GENP-59/2021-22 SPECIAL REPAIR TO RAIN WATER HARVESTING SYSTEM IN THE AREA OF AGE B/R I UNDER GE AF PALAM DELHI CANTT 10

Amount

Cleaning of existing Water hervesting upto 4 m depth and removal of sludge/ silt/liquid/mud/sand/water etc in foul position and removing the same from site to outside the MoD land complete all as specified and directed by the Engr-in-Charge.

Taking down mud plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removing the debris from site to outside of MOD land all specified and directed.

M&L for 10 mm thick rendering on fair faces of brick work or concrete surface in cement plaster 1:4 including finishing surface even and smooth without using extra cement and using water proofing compound as per manufacturer's instruction over roof complete.( Note :- Water proofing Compound shall be measured and paid seprately) .

Supply only water proofing compound (ISI marked) all as directed.

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations,filling and mass concrete including form work.

M&L for Reinforced cement concrete (design mix) in M-25 mix as in Slabs supported on walls,beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like including necessary form work complete.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S&F Mild steel TMT bars 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Supply and fixing in repair framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete

S&F in repair 1.60mm thick Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

M&L for welding in repairs exc 2.5cm but n exc 5cm in length of metal to be welded not exc 6mm thick.

M&L for preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamelled paint over one coat of red oxide zinc chrome primer complete.

Supply and fixing PVC (SWR) pipes,Type 'A' conforming to IS:13592 of 150mm bore (internal dia) with fittings, single socketed in any length with rubber ring joints including dismantling of existing pipe complete all as specified.

Demolition of reinforced concrete as in slab, roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar work including removel of debris from the site to out side MoD land.

M&L for 40mm graded Coarse aggregate, spread and leveled in trenches / recharging wells complete all as specified and directed by Engr-in-Charge.

M&L for 20mm graded Coarse aggregate, spread and leveled in trenches / recharging wells complete all as specified and directed by Engr-in-Charge.

M&L for drilling upto 300 mm bore holes by DHT cum rotary method upto 100 mtr depth from natural ground level in any type of soil including removal of surplus soil to a distance n. exc 100 Mtr complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in lime or cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B, brick, straight or curved on plain eexceeding 6 m mean radius built in cement mortar 1:6 complete.

akhil enterprises

Shri Kanchan Engineers