Beautification of entry Point in National Capital Territory of Delhi at Noida (Mayur Vihar). (SH- Civil, Horticulture and Electrical works). (Balance work).

Civil work

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.

All kinds of soil

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.

All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for :

Foundations, footings, bases for columns.

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works up to plinth level:

Concrete of M10 grade with minimum cement content of 220 kg /cum

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for : Edges of slabs and breaks in floors and walls

Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes.

NIT No:- 11/SE(East)M/PWD/2025-26

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge.

With granite stone of colour black, cherry/ruby red of area less than 0.50 sqm

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

250 mm dia. R.C.C. pipe

Add @ 3.00% Cost Index on DSR 2023

Providing and laying cement concrete tactile tile (for vision impaired persons as per standards) of size 300x300x60mm in outdoor floors such as footpath, court yard, multi modals locations etc. of required thickness, size shape made by table vibratory method using PU Mould, laid in required colour & pattern laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting of the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

60 mm thick C.C. tactile tile of M-35 grade with approved colour, design & pattern.

Providing and fixing Aluminium Composite panel sheet bend to the required shape and profile and fixed on existing column/.structure in approved design and filling the joints with silicon as per direction of Engineer-In Charge.

Providing and fixing machine cut, mirror/ eggshell polished , Granite stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. .

18 mm thick Polished Granite stone slab jet Black, Cherry Red, Elite

Providing and laying Vibro compacted cement concrete paver blocks ( make - chelsea ) of M-40 grade concrete having 80 mm thickness made up in fully automated plant with steel moulds resulted in precise dimensions with compaction @ 3200 psi including minimal water ratio content (3:1) with waterless curing by Rotho curing system to the required level and line laid over a bed of 20mm average thick cement mortar 1:4 (1cement : 4 coarse sand ), complete as per direction of Engineer-in-Charge. ( Color & pattern to be approved by Engineer in Charge)

80 mm thick cement concrete paver block of M-40 grade with approved colour, design & pattern.

Providing and fixing 100x100x60 mm Delhi stone cobble block hand cut and chisel, rough finish on top, mixed with red sand stone machine cut size 100/75x100x40 mm , for paving in parking floors and table top, etc. laid over 20 mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.

Providing and placing in position FRP Bollard of size 250 mm dia at top, 350 mm dia at bottom & 850 mm height of required/Approved shape & Size (As per Sample approved), including embedded 200 mm in cement concrete 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size), necessary excavation for the same in bitumen/ concrete pavement at specified spacing complete and as per direction of Engineer-in-charge.

Horticulture Work

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Rough dressing the trenched ground including breaking clods

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if

any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Flooding the ground with water including making kiaries and dismantling the same.

Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment).

Holes 45 cm dia, and 45 cm deep.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

Tree Plants

Shrubs Plants

Providing and stacking of Tecoma gaudichaudi of height 45-60 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Calliandra, emarginata of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Nerium oleander (kaner) of height 60-75 cm. with 5-6 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Add 18.00 % GST([email protected]%) on DSR 2020

Modified Estimated Cost due to correction in GST Rate @ 0.973 =(Estimated cost based on DSR 2023 items *0.973) = (-) (486813*0.027= 13144)

Add 7% Cost Index on DSR 2020

Add 1.00 % Labour Welfare Cess on DSR 2020

Providing and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Variegated, Glabra Formosa, Peruviana Odissi, Paratha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Phoenix sylvestris Roxb. (Wild date palm/khajur) of height 305-365 cm. in Big HDPE Bag as per direction of the officer-in-charge.

Supply and plantation of seasonal plants @ 25 cm c/c in plain area at designated locations consisting of plants variation as Cineraria dwarf, Marigold Jaffri, Mumulus Multi Branching, Nemesia, Petunia Hybrid, Phlox, Salvia Dwarf, Cosmos,Verbina pernelia, cocks-comb vinka, chrysanthemum, Dahlia,sunflower single, stock. The plant should be healthy and full of Foilage when planted. Plantatin works include watering, removal of dead plants and unservicable materils as per direction of officer in charge. Note : Name of the variety to be planted shall be get approved from Engineer-in-Charge.

Electrical Work

Per Bag

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required

63 mm dia (OD-63 mm & ID-51 mm nominal

Supplying & Laying of one number PVC insulated and PVC sheathed / XLPE aluminium conductor armoured power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL / PVC / DWC pipe i/c connections etc. complete as reqd.

3.5 x 35 sqmm

4 x 16 sqmm

Supplying & Laying of one number PVC insulated and PVC sheathed / XLPE copper conductor armoured power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL / PVC / DWC pipe i/c connections etc. complete as reqd.

4 core x 4 sq. mm

Supplying & Laying of one number PVC insulated and PVC sheathed / XLPE copper conductor armoured power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL / PVC / DWC pipe i/c connections etc. complete as reqd.

Supplying and drawing following sizes of PVC insulated PVC sheathed copper conductor multicore flexible cable of following size in the existing RCC/ HUME/ METAL / PVC / DWC pipe i/c connections etc. complete as reqd.

Supplying and fixing SMC (sheet moulding compound) cable junction box of nominal size 250 x 200 x 105mm with cover having IP55 ingress protection on wall surface/pole with suitable clamps/fastners i/c supplying & fixing 1 No. 63A 4 way terminal block, 1 No. 63 A TPN MCB with din rail, including connections etc complete as reqd.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3½ X 35 sq. mm (32mm)

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

4 X 25 sq. mm (28mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying, Installation, testing & commissioning of 40 W Colour Changing RGB type Ground Mounted LED Projector Light Fitting made of powder coated pressure die cast aluminium housing with heat resistance toughendglass having IP66 ingress protection i/c suitable CC foundation, connections etc. complete as required

Supplying, Installation, testing & commissioning of 25 W LED Bollard Light Fitting of 900mm minimum height made of decorative cast iron with hexagonal lantern with heat registance diffuser having IP66 ingress protection i/c suitable CC foundation and minor civil works, connections etc. complete as required

SITC of 7.5 HP 100X100 MM Open well submersible pump set capable of delivering 1800 LPM at a head of 10.5 mtr suitable for 3 Phase 415V 50Hz AC supply including necessary mounting arrangement, strainer, water proof cable joint, connections etc. complete as required.

SITC of 2 HP 50x50 mm Open well Submersible pumpset SS Body, SS Impeller and SS Shaft capable of delivering 430 LPM at a head of 12 mtrs suitable for 3 Phase 415V 50Hz AC supply including necessary mounting arrangement, strainer, water proof cable joint, connections etc. complete as required.

SITC of 0.5 HP 25X25 MM Dia Open well submersible pumpset CI Body. CI Impeller SS Shaft capable of delivering 130 LPM at a head of 12 mtrs suitable for 1 Phase 230V 50Hz AC supply including necessary mounting arrangement, strainer, water proof cable joint, connections etc. complete as required.

Supply & Installation of following size uPVC Pipe/Plumbing suitable for 10kgf/cm² i/c fittings & accessories etc complete as required.

110 mm Dia

63 mm Dia

25 mm Dia

SITC Of 100 mm Dia CI Butterfly valve with accessories in the existing pipeline etc. complete as required.

Supplying and fixing of Following Size GM Ball Valve with accessories in the existing pipeline etc. complete as required.

63 mm Dia

50 mm Dia

SITC Of 32 mm Dia Upvc Ball Valve with accessories in the existing pipeline etc. complete as required.

SITC Of Following Size Duel Plated CI Check valve with accessories in the existing pipeline etc. complete as required.

Supplying and fixing of Following Size GM Ball Valve with accessories in the existing pipeline etc. complete as required.

100 mm Dia

SITC Of 63 mm Dia Upvc Check Valve with accessories in the existing pipeline etc. complete as required.

Supplying & laying of following Size PVC insulated PVC sheathed copper conductor flexible cables for pump i/c connections etc. complete as required.

3 x 6 sqmm Flat Submersible cable

3 x 2.5 sqmm Flat Submersible cable

4 x1.5 sqmm Round cable

1.5 sq mm 2 core Round cable

SITC of 25 mm Dia Geyser Jet Nozzle to produce required water effect for water fountain etc. complet

e as required.

Supply & Fixing of 25 mm Dia Foming Jet Nozzles in SS 304 Gr to produce required water effect for water fountain etc. complete as required.

SITC of 25 mm Dia Swivel Connector to produce required water effect for water fountain etc. complete as required.

SITC Of Debris Collection Strainer in the existing pipeline etc. complete as required.

SITC Of 65 mm Dia Overflow Skimmer to produce required water effect for water fountain etc. complete as required.

SITC of 4000 mm Dia SS 304 Gr Round shaped Pipe ring made by 50 mm Dia Ss 304 gr. Pipe with 2 Nos 50 mm Dia inlets and 4 Nos 25 mm Dia Outlet i/c necessary mounting arrangements, connections etc. complete as required.

Supplying and fixing of 100 mm Dia SS pipe manifold complete with 100 mm dia inlet and 100 mm & 50 mm outlets as per site requirement i/c necessary mounting arrangements, connections etc. complete as required.

Supply installation Testing and Commissioning of 100 mm dia 100 mm long Spool piece with flanges at both ends with nuts bolts, rubber gaskets i/c necessary mounting arrangements, connections etc. complete as required.

SITC Of 6x3 Watt Donut Type WW water proof LED lights made out of stainless steel 304 gr with emitter type power LED's, tempered glass 8 mm having ingress protection class IP-68 i/c SS Stand, water proof joint, connection etc as required

SITC of High Power Circular 6x3 w RGB LED lights made out of stainless steel 304 gr with emitter type power LED's, tempered glass 8 mm having ingress protection class IP-68 i/c SS Stand, water proof joint, connection etc as required

SITC of Constant Voltage Driver (CVD) for LED lights 14 Amp 24 Volts for light controlling i/c connections etc. complete as required.