PROVISION OF MINOR WORK REVENUE WORK AND SPECIAL REPAIR UNDER AGE BR-I AGE BR-I AGE EM OF GE NORTH PATIALA AT PATIALA MILITARY STATION

Amount

Schedule 'A'Part -I (BUILDING SCHEDULE)

Total amount of Sch 'A' Part I (BUILDING SCHEDULE)

Schedule 'A'Part -II (BOUNDARY WALL/FENCING GATE)

Total amount of Sch 'A' Part II (BOUNDARY WALL/FENCING GATE)

Schedule 'A'Part -III (INTERNAL ELECTRIFICATION)

Total amount of Sch 'A' Part III (INTERNAL ELECTRIFICATION)

Schedule 'A'Part -IV (EXTERNAL ELECTRIFICATION)

Total amount of Sch 'A' Part IV (EXTERNAL ELECTRIFICATION)

Schedule 'A'Part -V (EXTERNAL WATER SUPPLY)

Total amount of Sch 'A' Part V (EXTERNAL WATER SUPPLY)

Schedule 'A' Part - VI (Misc B/R & E/M Schedule) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

B/R SCHEDULE

M&L 20mm thick screed in cement mortar (1:4) as in backing of floor, complete all as specified and directed.

M&L 10mm thick rendering in cement mortar (1:4) as in backing of wall tiles, complete all as specified and directed.

M&L for anti-skid ceramic joint free premium quality coloured tiles 400 X 400 mm and 6-7 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. and pointed in white cement with pigment to match the colour of tiles, including taking down old tiles complete all as specified and directed.

Providing and Laying Premium (1st) quality digitally printed straight edge, punched, glazed ceramic rectangle tile in approved shade and finish in coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, including taking down old tiles complete all as specified and directed. Note : Dado should be flushed with the wall plastering.

S&F Powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.28mm / 101.60X44.45X1.29 mm min thickness for chowkats or frame & shutters made of size 44.45x44.45x1.29mm min thickness for side rails and middle rail, 114.3X44.45X1.29mm min thickness for top rails and bottom rails complete all as specified and directed.

S&F aluminium casement windows (with provision for cooler) with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm min thickness and shutters made of 63.5X31.75X1.29mm min thickness complete all as specified and directed.

S&F Powder coated 50 microns extruded aluminium in 3 Tier Track Sliding Windows/glazing, with frame of section 100x44-45x1.30mm min thickness, track of size 100x38.10x1.30 & shutters made of size 32x18x1.3mm min thickness, with built in locking system for each leaf complete all as specified and directed.

Powder coated 50 microns extruded aluminium frame for fixed type partition made out of powder coated aluminium section of size 101.60 x 44.45 x 1.93mm, comprising of 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) inserted in and including necesary jointing cleats, rubber packing/EPDM gasket, anodised aluminium snap beading complete fixed to floor and wall by means of cadium plated steel screws complete all as specified and directed.

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm min thickness complete all as specified and directed.

S&F 12mm thick high density fibre board pre-laminated on both sides (water proof) below & above middle/lock rail in powder coated aluminium doors and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc aluminium beads 20 mm size with and complete all as specified and directed.

S&F 5mm thick tinted glass for aluminium windows / doors including EPDM gasket to render the glazing, air and water tight etc and power coated aluminium beeds 20 mm size complete all as specified and directed.

S&F stainless steel wire gauge 0.36 mm nominal dia of wire and average width of aperture 1.40mm to be fixed in Powder coated aluminium windows/ ventilators etc complete all as specified and directed.

S&F stainless steel (304 grade) finished butt hinges 125mm complete all as specified and directed.

S&F MS butt hinges 125mm complete all as specified and directed.

S&F powder coated aluiminium tower bolt 200mm long complete all as specified and directed.

S&F powder coated aluiminium tower bolt 150mm long complete all as specified and directed.

S&F powder coated aluminium handles 150mm complete all as specified and directed.

S&F powder coated aluminium hook and eye of suitabel length adjustable to aluminium window shutters complete all as specified and directed.

S&F 5mm thick frosted glass fixed to aluminium ventilator including necessary EPDm gasket to render the galzing, air and water tight etc and powder coated aluminium beeds 20mm sized complete all as specified and directed.

Factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified and directed.

LEAD FREE PVC Celuka ply 18 mm thick ( minimum density 600 Kg/Cum) of both side plain white colour , fixed with stainless steel screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed.

LEAD FREE PVC Celuka ply 18 mm thick (minimum density 600 Kg/Cum) of single side rigid lamination of approved colour and other side plain white colour fixed with stainless steel screws and solvent cement/ adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s specifications complete all as specified and directed.

S&F stainless steel Piano Hinges 20mm wide for cupboard, complete all as specified and directed.

Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity minimum 50 kgs complete all as specified and directed.

D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified and directed.

Preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion over and including 1.5 to 2.5mm thick putty complete all as specified and directed.

Applying 02 coats of interior plastic emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer including acrylick thick wall care putty 1.5 to 2.5mm thick putty complete all as specified and directed.

Applying 02 coats of interior plastic emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceiling surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer acrylick thick wall care putty 1.5 to 2.5mm thick putty complete all as specified and directed.

S&F health faucet (ABS Body) with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F PTMT jet spray with 1.00 metre PVC tube, (suitable for European seat) complete all as specified and directed.

S & F CP toilet paper holder with flat recessed type stainless steel complete all as specified and directed

S&F waste pipe 90 cm long flexible type suitable for 32 mm dia waste coupling, complete all as specifed and directed.

S&F 15mm dia chromium plated brass, autoclosing urinal valve, complete all as specified and directed.

S&F 6mm thick looking mirror with smooth finish bevelled edges/sides fixed to wall with stainless steel brackets/plugs/connecter/spacers/ screws etc. chrome finish complete fixed in position all as specified and directed.

S&F CP peg set of 6 hooks and including all accessories like screws etc as recommended by manufacturer and complete fixing in position complete all as specified and directed.

M & L 22mm thick PCC tiles laid over cement mortar 1:3 mixed with water proofing compound and joints grouted flush in cement mortat (1:3) complete all as speciied and directed. Note : WPC will be measured and paid for seprately.

Providing and fixing factory made aluminium ventilators with 80 micron powder coating of frame of 127X38.10X1.74 mm and fixed shutters made of 45X45X1.63mm including 5mm thick glass in lower half portion of shutters and stainless steel wire gauge 32 Gauge in upper half portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size complete all as specified and directed.

S&F intergrated lock of 75mm for aluminium doors with 2 keys, complete all as specified and directed.

M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. Note : Dado should be flushed with the wall plastering.

M&L for Baroda Green marble, machine cut as in shelves/steps/cills/jambs/skirting/border and the like works and flooring etc, 15-16 mm thick including bull-nosing the exposed sides, set and jointed in cement slurry over & including screed of 15 mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified and directed. Note : Single piece should be used in steps/cills/jambs/shelves.

S&F single liver basin mixer with popup waste system and 450 mm long braided hoses, fancy type, cast copper alloy, with capston head chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts screwed for 15 mm bore of iron pipe complete all as specified and directed.

S&F vitreous china premium/1st quality wash down water closet wall hung EWC P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc. incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete all as specified and directed.

S&F vitreous china premium/1st quality wash basin (under counter), white, size 580x430 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions complete all as specified and directed.

S&F concealed flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates and making space/cavity in existing brick work wall for fixing and taking down existing of any description/size complete all as specified and directed.

S&F Urinal pot with auto sensor sprinkler complete fixing accessories set of size 480 x 300 x 740mm including necessary fixing arrangements and incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories complete all as specified and directed.

S&F vitreous china premium/1st quality urinal division plates/partitions of size 720X320X90 mm including S&F all accessories as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete all as specified and directed.

S/F stainless steel soap dish, complete all as specified and directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fiber Reinforced Gypsum) false cell of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.50 to 0.75 as per IS 8225/1987; Noncombustible as per BS 476 Part 4, 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15x32 mm of length 3000 mm, cross T of size 15×32 mm of length 1200 mm and secondary intermediate cross T of size15x32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel hangar rod (galvanizing @ 80 grams per sqm) i.e. minimum 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm fully threaded hanger rod up to 1000 minimum length or as per length required at site for desired height and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 24X24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of 40mm long SS screws with plastic raw plugs at 450 mm center to center, with semi perforated 12 mm thick micro tegular edged GRG false ceiling, completed all as specified and as directed.

INTERNAL ELECTRIFICATION

Supply and fix in replacement of old unsv building light ,25 W IP 66 LED security light for building luminaire comprising of die cast aluminium housing with weather proof gasket for lamp & driver compartment with system wattage of 25 W . The LED make must be of minimum 100 lumen/watt CCT 6500K .The driver must be power factor > 0.95 with short circuit protection , open circuit protection , reverse polarity protection , high voltage protection. the luminaire must have secondary optics with perfectly matched lens for better light control with GI bracket of suitable size and clamps with fixing accessories connection with PVC insulated three core flexible copper conductor cable 0.75X3 Sqmm with proper clamps complete all as specified and directed.

S&F incl taking down 20 watt wall mounted, new generation LED batten fitting 4 feet with polycarbonate diffuser andextruded thermoplastic body > 90 lumen/watt having correleted color temperature(CCT) of Emitting light 6500/3000 K with CRI of LED >90 . including all fixing accessories & connecting up with PVC insulated twin core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F MCCB DB VTPN 4 WAYdouble door 240 volts with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting type, drilling holes for incoming and out going cables complete suitable for ways with IP65 protection complete all as specified and directed. (Note: MCCB should be B or C curve as directed by engineer in charge)

M&L in replacement of old/damaged earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level,the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected toand including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES SSR part I and testing on completion including necessary excavation and earth work in any type of soil,PCC(1:3:6)type C1 chamber,pre-cast RCC slab 50mm thic in cement concrete (1:2:4),type B1,reinforced with welded steel wire fabric or XPM,(weight not less than 4 Kg per Sqm) with cast iron frame,funnel with watering pipe 20mm dia medium grade,wire mesh and lugs,GI protection pipe,15mm dia,light grade,7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

S&F Lamp holder including LED bulb 12 W including flexible wire 0.5 Sqmm copper cable complete all as specified and directed.

S&F Surface Mounted LED Bulk Head Luminaire of capacity 10 watt with ABS Body & Polycarbonate Diffuser, IP54 inc connection with ,with flexible wire 0.5 sqmm copper cable complete all as specified and directed.

Supplying & laying factory made unreinforced Precast concrete cable covers class LV type 1, flat, Size 250x150x40mm laid in trenches as protection to cables complete all as specified and directed.

S & F MCB , SPN, 240 Volts ,32-40 amp for fixing in DBs of including proper thimble connections complete all as specified and directed.

S & F MCB, single pole 240 volts 6 to 32 Amp capacity for fixing in DB’s including proper thimble connections complete all as specified and directed.

M & L for Earthing complete with galvanized iron earth plate electrode of size 600x600x6.0mm , buried directly in ground (earth pit not less than 2.25 mtrs below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts , nuts , check nuts and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate 20 mm dia watering pipe medium grade 1.70 mtr long with a plug at top, GI protection pipe light grade 15 mm dia from earth pit to main board including PCC pit in cement concrete 1:2:4 along with CI frame and cover 10mm thick duly hinged to CI frame as shown in the electrical plate No3 of SSR 2009 part 1 specification at page 497 complete all as specified and directed.

Supply and fix Tube light fitting Self Ballasted LED Batten. Extruded Thermoplastic body with PC Diffuser in square LED Batten 18/20W 6500K of capacity ,20 watt,4 ft long incl 3 core flexible wire 0.5 sqmm copper cable complete all as specified and directed.

Supply & fix mirror light with Linear & compact 12 W mirror light with decorative grey end caps, polycarbonate body and ribbed opal diffuser of capacity 12 watt complete all as specified and directed.

Supply & fix Exhaust fan AC single phase 230/240 v of size 200 mm sweep 900 rpm Engineering thermoplastic body, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated including Louver , making holes, grouting nut-bolts and make surface good complete all as specified and directed.

Supply and fix House Service bracket (hook type) complete with 3 meter long GI pipe 40 mm dia medium grade, two nos 90 degree bends M.S hook and stay or guy complete all as specified and directed.

Supply fabricating and fixing angle iron frame made out of 40X40X5 mm thick suitable for fixing of desert cooler including necessary civil work, making good the disturbed portion of wall including colour/white wash as per existing surface complete all as specified and directed.

Fixing and Installation of desert cooler with outer body made of PGI (plain galvanized iron) sheet not less than 1.2 mm thickness for fixed part, thickness of PGI sheet for shutter not less than 0.8 mm thick front grill made of PGI Sheet with minimum weight 2.8 kgs overall outer size not less than 66cm X 66cm X 99 cm(HEIGHT) electric driven copper wounded fan motor having nominal air flow capacity 4000 cum per hour and capacity of water storage tank not less than 80 ltr and submerible pump for required flow of water single phase) complete all as specified and directed. Desert cooler will be issued to contractor free for fixing)

S&F Lamp holder ,PVC/polycarbonate type with back plate suitable for batten fitting complete all as specified and directed.

Supply,installation and testing of minimum 5 star rated electric water heater (Geyser) metal body storage type of 20 ltrs capacity of Steel tank inclding 04 nos anchor fastining for mounting geyser and other nut,bolt and washers with 3 core flexible wire of size 2.5 Sqmm from Geysere to metal plug and socket complete all as specified and directed.

Supply and fix tube light fitting LED type integrated 9/10 watt, 2 ft long incl LED tube rod and incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed.

S & F Exhaust fan 300 mm sweep complete all as specified and directed.

S&F LED bulb 9 watt complete all as specified and directed.

S&F Single pole & neutral 4 way door closer DB with 200 amps rated bus bar complete all as specified and as directed.

EXTERNAL ELECTRIFICATION

Supply & fixing of LED Flood light fittings of capacity 120 watts IP-66 , complete with accessories and mountig clamp including suitable nut/bolts/washers etc complete all as specified and directed at site. Note:- Contractor will submit the manufacturer test certificate and an extended warranty card for two years certificate by manufacturer

Supply and fix steel tubular swaged poles type 410 SP-31 (9.0 meter long)complete with CI base plate and finial complete all as specified and directed

Supply and fix junction box made out of PVC 30cmx20cmx10.5cm complete including aluminium bus barr of suitable size three phase with insulators, including mounting arrangement flat iron clamps,nut bolts washers etc for clamping with steel tublar pole complete all as specified and directed.

Supply and fix PVC insulated round/flat copper cable of size 3 core 2.5 sq mm for connection of LED lights from FRP junction box to street light fittings complete all as specified and directed.

Earthing complete with Galvanized steel earth plate 600 x 600 x 6.0 mm buried directly in ground (earth pit not less then 2.25 Mtr deep below ground level) with top edge of the plate not less then 1.5 Mtr below normal ground level connected togalvanized earth lead wire 4.0 mm dia by means of bolts ,nuts ,check nuts and galvanized iron or steel incl excavation and earth work, GI pipe light grade 25mm/40 mm bore for protection of GI wire /strip from earth electrode to and incl the earth test point of gun metal or phosphorus bronze size of size 75 X 75 X 25mm drilled and screwed including, 3 NOS, 8mm dia 25mm long hex, head screw supplying and lying charcoal dust, common salt, PCC 1:3:6 type CI (using 20 mm graded crushed stone aggregate) as in chamber and MS angle iron frame 40 x 40 x 3mm and RCC cover 40 mm thick 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) reinforced with 8 mm dia. TMT bars @ 75mm c/c both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate No. 3 of SSR Part I of 2009 and connected to earth test point incl testing complete all as specified and directed

Suppy and fix Rigid non-metallic PVC conduit 20 mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers,lock nuts,saddles,pipe hooks etc.

M&L for iron frame work of suitable for symmetrically fitting of 4 Nos of LED Flood light fittings of capacity 120 watts and mounting on steel tublar pole complete with MS clamp bolts and nuts complete all as specified and directed.

Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply & fix Prestressed concrete pole, 9.0 metres long, 102mm x 152mm at top and 102mm x 289mm at bottom, class 10 including painting of 05 Nos alternate strips of black and yellow paint up to 1.5 mtr from PCC coping complete all as specified and directed.

Supply and fixing GI bracket 1.2 mtr long 40 MM dia complete with MS clamp bolts and nuts for fixing of bracket complete all as specified and directed.

Supply and fix junction box made out of PVC 30cmx20cmx10.5cm complete including aluminium busher of suitable size three phase with insulators and MCB SP of 6 Amps complete all as specified and directed.

Rigid non-metallic PVC conduit of size 20 mm exclusive of boxes (junction/ terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed.

Supply and fix PVC insulated round/flat copper cable of size 3 core 1.5 sq mm for connection of LED lights from over head conductor to street light fittings complete all as specified and directed.

EXTERNAL WATER SUPPLY

Material and labour for cutting the existing pipe line of 40 mm dia and insertion tee of 40x40x20 mm complete all as specified and directed. Note :- Excavation and earth work shall be measured and paid seperately.

M & L for constructing of brick mesonary pits of internal dimensions 0.6mtr x 0.6 mtr x 0.6 mtrs ( bottom PCC floor of the pit should be minimum 30 cms below the bottom surface of valve flange to provide sufficient working space) , bottom floor of the pit be constructed in PCC (1:3:6) 15 cms thick with 20 mm stone aggregate, inner and exposed surfaces and bottom floor of the pit should be plastered in CM (1:4) 15 MM thick. The valve and other fittings should be housed in center of the pit. the vertices of the pit should in right angle and champhered .The top cover of the pit will be made out of MS sheet min 5mm thick witth angle iron frame made out of MS angle 40mm x40 mmx 5 mm with galvanised steel hindges two nos ,and locking arrangements duly painted with two coats of water resistant synthetic enamelled paint over one coat of red oxide complete all as specified and directed.

Buttar Construction Co.