SPECIAL REPAIR TO JCOS/OR MD ACCN NO P-145 AT OLD SALARIA ENCLAVE OF JAK RRC UNDER GE (WEST) JABALPUR

Amount

Taking down or up steel tubing and connections for 20 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 15 mm bore of pipe complete all as specified and as directed.

Dismantling water tanks of capicity exceeding 500 ltrs to not exceeding 1000 ltrs complete all as specified and directed.

Taking down Chowkats or frames with shutters [without taking of shutter from the frame] not exceeding 1.5 Sq.m each complete all as specified and as directed.

Taking down Chowkats or frames with shutters [without taking of shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each, resecuring, easing, adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and directed.

Taking down shutter of any description n exc 1.0 sqm each complete all as specified and as directed.

Removing old tar felt, all loose dirt, old roof tiles, including taking down cement plaster, cleaning the concrete surface, and including removal & cleaning of vegetation, fungus,moss, small trees. etc., from the roof top with wire brush, removing the strips of lightening conductor and including refixing the same after repair work complete all as specified and directed.

Taking down Cement Plaster any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

Dismantling of Stone slabs and kota stone, Cuddappa stone, Granite, Chequered tiles, Paver block, etc of any description or any thickness, as in floors, aprons etc. laid, bedded and pointed in any cement mortar complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including cement mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris of the premises complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] complete all as specified and as directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out,sof/loose soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling plugging holes etc. in aprons complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed.

M&L Cement concrete type C-2(1:3:6) (40 mm graded stone aggregates) in benching, foundations, filling and mass concrete complete all as specified and directed.

M&L for cement concrete type B1 1:2:4 (20mm graded aggregate) as in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, Hold fast and similar works water troughs and the like including weathering, slightly rouinded for chamfered angles and necessary formwork all as specified and as directed.

M&L 50 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate laid in panels surface finish even and smooth using extra cement as in plinth protection, hard standing and similar works complete all as specified and as directed.

Supply only Liquid water proofing compound

M&L Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20mm graded aggregate) as in chajjas etc complete all as specified and as directed.

M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as desribed in serial item No. 26 above, but except bricks.

S & F Factory made PVC door frame of size 50x47mm single revated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, with wood free EPC, supplying & fixing in frame at site as per specification & drawing. complete all as specified and directed.

S&F 35 mm factory made shutters of second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat complete all as specified and directed.

M&L for 35 mm thick 2nd class hard wood glazed/gauzed and skelton door shutter, factory made, open rebated and prepared to receive glass/guaze etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guaze etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat, complete all as specified.

S&F aluminium powder coated window sliding type (3 track), 1.5mm thickness of frame and shutter with two glass shutter and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick plain float glass and 0.36mm dia apperture 1.4mm SS wire mesh and fittings etc and making good the jambs and painting with existing surface matching, complete all as specified and directed.

S&F aluminium powder coated louvered ventilators of 1.50mm thick frame including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. making good the jambs and painting with existing surface matching, complete all as specified and directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

M&L for 150 mm long, of PTMT handle , complete all as specified and directed.

S & F Aluminium anodised Handle, Cast Type, of size 150 mm complete all as specified and as directed.

S&F 75mm long Butt hinges,of PTMT, and fixed complete all as specified and directed.

M&L for 150 mm long of PTMT tower bolt, complete all as specified and directed.

S & F in repairs Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F Stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S&F TMT Bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S & F for frame work such as grill, grating etc with ends bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 125x60mm for doors, with double rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 105x60mm for doors, with single rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm crushed stone aggregate as in leveling course Iincluding demolition of existing PCC complete all as specified and as directed.

M & L for rendering 10mm thick in cement mortar 1:4 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions on existing surface after removal of the existing treatment for levelling the surface smooth to receive the water proofing membrane complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for preparation of surfaces, priming the surface with bitumen primer @ 400 grams per Sq.m, applying a coat of Blown Bitumen of grade 85/25 or 90/15 @ 1.2 Kg per Sq.m, laying APP based Polymeric water proofing membrane of minimum weight 3.0 Kg per Sq.m and minimum thickness of 3mm reinforced with polyster non woven fabric (weight not less than 150 gms/ sqm) by torch application with 100 mm overlap by thermo fusion including coating the surface with compatible blow bitumen of 85/25 @ 1.2 Kg per Sq.m and finished with two coats of bituminous aluminum paint @ 100 grams per Sq.m per each coat on top for water proofing treatment complete all as specified.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished fair and even complete all as specified and as directed.

M & L for 5mm thick plaster in cement mortar 1:4 mixed with water proofing compound over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces including finishing the top coat even and smooth all as specified Note: Water proofing compound will be measured and paid separately.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L Cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in sub base, 75 mm thick, complete all as specified and directed.

M & L for 100mm thick PCC 1:4:8 type D-2 using 40mm graded aggregate stone as in subbase, Hard standing and similar works complete all as specified and directed.

M&L for Machine cut cudappa stone slab 20-25mm thick as in Shelf/cooking platforms, and like including cutting and fixing over and including 20mm thick cement screed base in CM (1:4) and jointed to support granite top complete all as specified and directed.

M&L for zed granite Black Work 18 to 20 mm thick (table rubbed and polished ) as in steps , jambs, pillars, window- cills, cooking platforms, and like over and including 20mm thick cement screed bed in CM (1:4) and including pointing with white cement (1:2) using marble dust with admixture pigment to match with shade of slab complete all as specified and directed.

M&L for Granite tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15 mm thick screed bed of CM (1:4) , as in treads and risers of staircase, steps, jambs, pillars, window- cills, complete complete as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

S & F Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

S & F Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L Glazed ceramic colour tiles in vertifical surface 350x 250x 7mm/ 450X 350X 7mm thick with necessary border etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick renderting/ backcoating in cement mortar 1:4 complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, over and including screed bed or bedding layer in cement mortar(1:6), 15 mm thick for steps, floor, including rubbing and mirror polishing complete all as specified and directed.

M&L Machine cut kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar, over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, over and including 10 mm thick cement plaster (1:4), on fair faces of brick work or concrete surface as backing, including rubbing and polishing complete all as specified and directed.

Material and labour for 60mm thick machine pressed glossy finish precast concrete interlocking paver block any shape and size & Colour M-40 grade with grey cement and pigment confirming to IS 15658-2006 complete all as directed.

Complete removal of existing treatment on wall surfaces complete all as specified and directed

M&L for 1 mm thick wall care putty on wall surfaces, complete all as specified and directed.

M & L for washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of oil bound distemper on wall surfaces complete all as specified and as directed.

M&L for subsequent coat Oil emulsion distemper on wall surfaces, complete all as specified and directed

M & L preparation of New plastered surfaces of ceilig and applying three coats of white wash complete all as specified and as directed.

M & L complete removal of existing treatment on ceiligs and applying three coats of white wash complete all as specified and as directed.

Material and labour for complete removal of existing treatment or new surfaces, preparation of old decorated treatment on wall / ceiling / chajja by scrapping with trucare wall sander : L-01/H-01 (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying two coats of Anti fungal weather proof grade exterior acrylic emulsion paint of approved tint over a coat of weather proof primer with crack filling upto 5 bars of positive hydrostatic pressure on vertical walls without any dilution with forced coverage not more than 3.5 sqm / ltr as per manufacturer's instructions and all coats including primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed.

M&L preparing old wood or wood based surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified

M &L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of any tint all as specified and directed.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primere complete all as specified.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and directed.

Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and directed.

S & F Rotational moulded Polythene [HDPE] Water Tanks, Cylindrical & Vertical Type 1000 Liters Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and directed.

S&F 20 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding ditto but including brackets.

S & F in repair water closet (Squat Pattern) complete including provn of lime concrete bedding Orissa pattern size 580 x 440mm white with integral foot rests (excluding flush pipe or flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor to match with existing complete all as specified and directed.

S&F in rep Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) fixed as in repair, complete all as specified.

S & F in repairs PVC High/Low level flushing cistern 10 litrescapacity including all fittings I.e float valve, syphon, flushpipe,brackets all as specified and directed.

S&F, in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers & wastes including CI cantilever bracket & connection union to pipe over all size 915mmx460mm & bowl size 410 x330x160mm complete all as specified and as directed.

S&F in repair 15 mm bore Stop valves/angle cock, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,conceledd,fancy type, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S & F in repairs Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

S & F in repair PVC connections 15mm dia with PTMT nut on both ends and washers 450mm long complete all as specified and directed.

S & F in repair 15 mm dia, fancy type bib taps cast copper alloy CP with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule 15mm bore dia complete all as specified and as directed.

S&F in repair PVC floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified and as directed.

S&F in repair towel rail 450 mm long of Brass CP fixed with and including chromium plated brass screw and wooden / plastics cleats ( min wt 170 gms) complete all as specified and as directed.

S & F in repair of 110 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches,floor and wall including taking down old unserviceable pipe any description and any type complete all as specified.

S & F in repairs PVC (SWR) Pipes single socketed in any length with rubberring joints laid in trenches or in floors and wall 75mm bore including taking down old unserviceable pipe any description and any type complete all as specified and as directed.

S&F 110mm dia (bore of pipe) PVC bends (any radius), diminishing pieces or tapers (larger bore measured) with cement joints,with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) bends 75mm dia bore any radius with access door complete all as specified and as directed.

S&F in repairs 75mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and as directed.

S&F in repairs 110mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and as directed.

S&F in repairs 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair 18/19 mm thick water proof block board of commercial quality Gde-I fixed with screws as kitchen , cup board box and shutters & shelves etc complete all as specified and as directed.

S&F in repair 18-20 mm thick Acrylic PVC Board, prelaminated one side with decorative choice lamination & other side balancing white lamination approved texture as in kitchen cabinet,Cupboard etc (with shelves and partition ) including necessary fittings & fixtures as per manufacture's instrucions complete all as specified and as directed.

M&L 6 mm thick cover fillets of standard hard board, 40 mm wide and fixing with screws complete all as specified and as directed.

S&F in repairs 1st class HW Beads, straight ( 20 mm size) for glazed or gauzed joinery, renewed, including mitres etc., Plain or moulding as requirement, complete all as specified and as directed.

S&F in repairs 30 mm wide Steel Continous (piano) hinge, steel bright finish or electro galvanised etc complete all as specified and as directed.

S&F and in repair 40 mm dia , SS cupboard knobs fixed with nut ,screw and washer of mild steel bright complete

M & L 25mm thick crushed stone dust/sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all respect as specifiedcomplete in all respect as specified

S&F in Repairs Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed .

S&F in Repair Brass CP WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed .

S&F in repairs for stainless steel kitchen plate rack of size 24"X36"X10", three tire, ISI marked, including all fittings complete all as specified and as directed..

M&L Formwork to chullah hoods, chajjas, troughs and similar items including edges flat surfaces of concrete rough finished complete all as specified and as directed.

S & F in repairs curtain rod stainless steel with brackets for each, stops, rollers etc. and fixed in position complete.

Supply, laying and testing of 150 mm inner diameter of double wall corrugated (DWC) high density polethelene pipes(HDPE) and stiffness class-8 (SN-8) with ISI marked (with CML No) with and including all fittings & jointing materials for sewage line and laid in trenches as specified in IS-16098(Part-2):2013 and as per manufacturer's instruction complete all as specified and as directed. Note:- Bedding of pipe shall not be provided in normal condition and construction methods shall be strictly compiled as per clause no A-4 Annex 'A' of IS 16098(Part-2):2013

Taking down carefully any type of old unserviceable point wiring (light, fan, socket bell or power) , complete with fittings such as switches ceiling roses, lamp holders sockets, regulators with PVC conduit surface /concealed or wooden patterns including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

Taking down the ceiling fan in situ and removing to MES store complete all as specified and directed.

Taking down carefully Main switch and Distribution boards any make and size complete all as specified and as directed .

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/ PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 6.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting, fixing accessories and 4 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 6.0 Sqmm Wire and One No of 4 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 4.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting, fixing accessories and 4 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 4.0 Sqmm Wire and One No of 4 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

(a) One light point/Bell point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket point controlled by one switch on same board.

(d) One socket point controlled by one switch on Independent board.

All as described in serial item No. 32 here-in-before, but with 1100 volts grade copper standard conductor FRLSH cable of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor cable for 3 pin 15 Amp switch socket outlet independent board complete all as specified and directed.

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed.

S & F Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed.

S & F Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed.

S & F switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and as directed.

S & F Ceiling rose surface bakelite 65 mm x 50 mm three terminal AC 230 volts flush type complete all as specified and as directed.

S&F fan regulator Step type of polycarbonate complete all as specified and as directed.

S&F LED lamp rotary type/holder type of 12 watt all as specified and as directed.

S&F in replaceement of decorative wall light fitting WITH LAMPS 12 WATT made up of Polycarbonate, City-1, Cylindrical shape, with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed. Make:City 1 of havells or equivalent makes mentioned here-in-after.

S&F in repairs Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), (Make : Philips Cat part No BN 021 LED 22S 6500/4000 PSU GR S1 or equivalent makes as mentioned here-in-after.

S & F in repair of LED Decorative /mirror light fitting 9 watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge. Make- Havells LUMILINEPLUSSBS10WLED865SPCSS or equivalent makes as mentioned here-in-after.

S & F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed. Make :Havells Cat Part No. HEXAFT10WLED857SSYMBOPC or Equivalent make Philips / BAJAJ / WIPRO

Supply & fix in replacement of LED Security Light Luminaire 35 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed. Make:Havells cat part no: LHDAUU7PA7J025 or equivalent in Philips, Bajaj or Surya

S&F in replacement of sheet steel enclouser distribution boards, double door factory made VTPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 63 amps , circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed.Make of Distribution Board Legrand cat no:5077 50 or equivalent in seimens /GE and Make of MCBs :Legrand/Seimens/GE

S & F MCB TPN 25 to 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells)(Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge Make : Havells/ CG/ Bajaj

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.Make : Legrand CAT NO 507611 / SIEMENS CAT NO 8 GB 32102RC8/GE

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand DX3 DP CAT No 408637/ Siemens cat no- 5SL 42327RC / GE

S & F for MCB Single pole rated capacity 5 to 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand cat no DX3 SP 408587,408590,408592,408593,408594,408595 / Siemens cat no- 5SL41067RC, 5SL41107RC, 5SL41167RC, 5SL41207RC, 5SL41257RC, 5SL41327RC / GE

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed. Make:- Legrand/ havells or Equivalent

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep PVC body complete , including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed by Engineer in charge

Supply and lay DWCP pipe OD 65 mm , ID 38 mm all as per required and directed by Engg I charge(Necessary excavtion may please be added in rate quoted) complete all as specified and as directed.

Supply and laying Sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. NOTE : Punned thickness only shall be measured and paid.

supply and laying the Brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class ‘B’ bricks laid dry flat complete all as specified and directed by Engr in charge.

Rai Construction Co (BID ID -3347867)

Kirti Chandeliya and Assosicates (BID ID -3348179)

chandra builders (BID ID -3348201)

Maa Bhawani Construction (BID ID -3348170)

ANAMIKA CONSTRUCTION (BID ID -3348457)

RAVI ENTERPRISES (BID ID -3347819)

TRISHLA CONSTRUCTIONS (BID ID -3348102)