Special Repair of Toilet block (Civil, Plumbing and Electrical works) and other allied civil works at PM Shri Kendriya Vidyalaya Bantalab, Jammu

Name of Work: Special Repair of Toilet block (Civil, Plumbing and Electrical works) at PM Shri Kendriya Vidyalaya Bantalab, Jammu.

S.NO DESCRIPTION DSR AMOUNT NS AMOUNT

1 CIVIL & ALLIED WORKS ₹ 7,810,008.15 ₹ 124,455.32

2 PLUMBING WORKS

3 ELECTRCAL WORKS ₹ 1,278,063.00 ₹ 0.00

GRAND TOTAL (I/C GST) ₹ 9,359,000.00

GRAND TOTAL (I/C GST) ₹ 9,359,000.00

Digitally signed by AMIT

S.NO. DESCRIPTION UNIT BOQ DSR RATE DSR AMOUNT NDSR RATE NDSR AMOUNT

REPAIR OF ROOF (WATER PROOFING TREATMENT)

Providing and laying APP (Atactic Polypropylene Polymer) modified

prefabricated five layer 3 mm thick water proofing membrane, black

finished reinforced with non-woven polyester matt consisting of a coat

of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same

membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and

1 14.91 viscocity 70-160 cps. Over the primer coat the layer of membrane shall

be laid using Butane Torch and sealing all joints etc, and preparing the

surface complete. The vital physical and chemical parameters of the

membrane shall be as under : Joint strength in longitudinal and

transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in

longitudinal and transverse direction as 300/250N. Softening point of

membrane not less than 150°C. Cold flexibility shall be upto -2°C when

Removing dry or oil bound distemper, water proofing cement paint and

2 13.91 the like by scrapping, sand papering and preparing the surface smooth SQM 360.00 25.15 9,054.00

including necessary repairs to scratches etc. complete.

1:2:4 (1 cement : 2 coarse sand (zone-III) including

manufactured sand derived from Recycled Concrete

3 4.1.3A Aggregate (RCA) upto 25% : 4 graded stone aggregate 20 Cum 38.70 7654.85 296,204.42

mm nominal size including Recycled Concrete Aggregate

(RCA) upto 25%)- 45 mm thickness

15 mm cement plaster on the rough side of single or half brick wall of

mix : 1:6 (1 cement: 6 fine sand)

ASSEMBLY GROUND STAGE FLOORING & STAIRCASE PLASTERING

15 mm cement plaster on the rough side of single or half brick wall of

1:4 (1 cement: 4 fine sand)

Kota stone slab flooring over 20 mm (average) thick base laid over and

jointed with grey cement slurry mixed with pigment to match the shade

of the slab, including rubbing and polishing complete with base of

cement mortar 1 : 4 (1 cement : 4 coarse sand) :

7 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) cum 25.00 2434.25 60,856.25

Digitally signed by AMIT

TOILET FLOORING AND WALL DADO

Dismantling tile work in floors and roofs laid in cement mortar including

stacking material within 50 metres lead.

Providing and laying vitrified floor tiles in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08%

and conforming to IS: 15622, of approved make, in all colours and

shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse

sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting

the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08%

and conforming to IS:15622, of approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4

10 11.41A coarse sand) jointing with grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only . Laying of

tiles will be done with the notch trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for placing the tiles gently

Scraping old white or Colour wash including disposal of refuse as

directed by E-in-C within a distance of 60 meter.

Dismantling existing plaster including disposal of refuse as directed by

Engineer-in-charge within a distance of 60 meter (200 feet)

13.5 15 mm cement plaster :

Providing and applying white cement based putty of average thickness

14 13.80 1mm of approved brand and manufacture over the plastered wall SQM 2620.00 156.05 408,851.00

surface to prepare the surface even and smooth complete (13.80)

Distempering with 1st quality acrylic distemper (read made) having VOC

content less than 50 gm per ltr of approved manufacture and of

required shade and colour complete as per manufacture's

specification. (13.108)

New work (two or more coats) over and including water

16 13.41.1 thinnable priming coat with cement primer having VOC content SQM 650.75 185.65 120,811.74

less than 50 gram/litre

Wall painting with acrylic emulsion paint, having VOC content less that 50

17 13.82 grams / litre, of approved brand and manufacture, including appliying

additional coats wherever required, to achive even shade and colour.

Digitally signed by AMIT

Applying priming coats with primer of approved brand and manufacture,

having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having

VOC content less than 50 grams/litre

Digitally signed by AMIT

DOOR AND WINDOW

Dismantling doors, windows and clerestory windows (steel or wood) shutter

19 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking within 50

15.12.2 Of area beyond 3 sq. metres Each 22.00 502.75 11060.50

DOOR FRAMES- Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position with hold fast

20 9.1 lugs or with dash fasteners of required dia & length ( hold fast lugs or dash

fastener shall be paid for

9.1.1 Second class teak wood CUM 1.05 142949.70 150097.19

FLUSH DOOR:- Providing and fixing ISI marked flush door shutters conforming to IS

: 2202 (Part I) non-decorative type, core of block board construction with frame

of 1st class hard wood and well matched commercial 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters :

35 mm thick including ISI marked Stainless Steel butt hinges with necessary

Providing & Fixing decorative high pressure laminated sheet of plain / wood

grain in gloss / matt/ suede finish with high density protective surface layer

22 9.127 and reverse side of adhesive bonding quality conforming to IS : 2046 Type S,

including cost of adhesive of approved quality.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum

23 9.23 depth on all edges of flush door shutters (over all area of door shutter to be SQM 46.00 462.35 21268.10

Providing and fixing wooden moulded beading to door and window frames

with iron screws, plugs and priming coat on unexposed surface etc. complete:

9.40.1 2nd class teak wood

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH

25 MR 123 with Roses & Escutcheon in SS packaged with Mortice lockset 55mm EACH 22.00 3415.06 75131.32

backset, 20 SS forend, SS strike plate and EP Cylinder for all flush doors.

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised

26 9.97 (anodic coating not less than gradeAC 10 as per IS : 1868 ), transparent or dyed

to required colour or shade, complete:

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor

door stopper with necessary screws, etc. complete.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10

mm diameter bolts, nuts and wooden plugs and embedding in cement

28 9.53 concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded EACH 132.00 228.85 30208.20

stone aggregate 20mm

29 MR Door Closer:- Providing and Fixing Door Closer For Entry Door EACH 22.00 2242.00 49324.00

Polishing in high gloss/matt finish melamine clear polish on wood work in

30 13.116 required color/wooden shade texture with following process in the sequence as

detailed below:

Digitally signed by AMIT

The surface to be polished is rubbed with sand paper 80/120 no. and then with

sand paper of 160/180 nos.

Applying two coats of sealer with spray gun and allowing sufficient drying time

for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.

On drying of sealer coat, wet rubbing with emery cloth of finer grading with

ample water to remove excess sealer layer and make the surface further

smooth after this wet rubbing, then surface is applied with special grade

melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be

allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this

surface is further allowed to dry for 12 hrs

On this, 1st coat of melamine polish is applied with spray gun using melamine

clear polish and melamine thinner in required proportion. This 1st coat is allowed

to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is

further allowed to dry for 12 hrs. The final melamine polish is applied with SQM 87.00 3049.85 265336.95

compressor pressure spray gun using melamine clear polish and melamine

thinner mixed in required proportion complete as per direction of Engineer-in-

Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Disposal of building rubbish / malba / similar unserviceable, dismantled or

demolished material by mechanical transport including loading, unloading and

stacking, beyond 50 metres initial lead, complete as per direction of Engineer-in-

Dismantling doors, windows and clerestory windows (steel or wood) shutter

32 15.12 including chowkhats, architrave, holdfasts etc. complete and stacking within 50

15.12.1 Of area 3 sq. metres and Below Each 16.00 367.20 5875.20

15.12.2 Of area beyond 3 sq. metres Each 10.00 502.75 5027.50

Digitally signed by AMIT

Providing and fixing factory made uPVC glazed/wire mesh windows/doors

comprising of lead free uPVC multi-chambered frame, sash and

mullion/coupler (where ever required) extruded profiles having minimum wall

thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and

R4 profiles conforming to EN: 12608 in any shape, colour and design duly

reinforced with galvanized mild steel section made of required shape & size as

per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline

sash adaptor (where ever required) of appropriate dimension, EPDM gasket,

hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head,

comprising of matching polyamide PA6 grade sleeve for fixing frame to finished

wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary

stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be

mitred cut and fusion welded/mechanically jointed duly sealed at all corners,

33 9.147A including drilling of holes for fixing hardware and drainage of water etc. After

fixing frame the gap between frame and adjacent finished wall shall be filled

with weather proof silicon sealant over backer rod of approved size and quality,

all complete as per approved drawing conforming to CPWD specification &

direction of Engineer-in-Charge. Section of steel reinforcement and cross

sections of uPVC profiles to be as per design approved by Engineer-in- Charge.

Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with /

without high performance coatings as per design requirements and conforming

to IS: 3548 & IS: 16231 shall be paid separately.

Note: Structural design proof checked from a Government Engineering Institute,

to be provided by the manufacturer for : (i) Sites with basic wind speed > 45

m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all

Two track two panels sliding window with Aluminium channel for roller track,

9.147A1 wool pile, nylon rollers with SS 304 body.

Using R2 series with frame (40mm & above) x (40mm & above) & sash (25mm &

9.147A1.1 above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks sqm 70.20 8298.85 582579.27 - -

with hook (Height upto 1.2 metre).

Filling the gap in between aluminium frame & adjacent RCC / Brick / Stone

work by providing weather silicon sealant over backer rod of approved quality

as per architectural drawings and direction of Engineer-in-charge complete.

21.8.1 Up to 5 mm depth and 5 mm width Rm 172.00 96.75 16641.00 - -

Steel work welded in built up sections/ framed work, including cutting, hoisting,

35 10.25 fixing in position and applying a priming coat of approved steel primer using

structural steel etc. as required

Steel work welded in built-up sections / framed work in gratings/frames/guard

bars/railings/brackets/gates and similar works

Painting with synthetic enamel paint of approved brand and manufacture to

give an even shade:

13.61.1 Two or more coats on new work Sqm 91.00 155.90 14186.90 - -

Providing and fixing angle iron frames for doors, windows and ventilators of mild

steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron

35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall

with dash fastener, including fixing of necessary butt hinges and screws and

applying a priming coat of approved steel primer, all complete as per the

direction of Engineer-In-charge.

Digitally signed by AMIT

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) SQM 50.00 1123.80 56190.00

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every

third course of half brick masonry.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors

(cost of glass excluded)

9.24.1 Rectangular or square SQM 15.00 199.15 2987.25

SANITARY FIXTURES

Providing and fixing one piece construction white vitreous china

squating plate with an integral longitudinal flushing pipe, white PVC

automatic flushing cistern, with fittings, standard size G.I / PVC flush pipe

41 17.2 for back and front flush with standard spreader pipes with fittings, G.I

clamps and C.P brass coupling complete, including painting of fittings

and cutting and making good the walls and floors etc. wherever

17.2.1 Single squatting plate with 5 litre P.V.C automatic flushing cistern. Each 15.00 6515.55 97,733.25

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar

taps, 32 mm C.P. brass waste of standard pattern, including painting of

fittings and brackets, cutting and making good the walls wherever

White Vitreous China Flat back wash basin size 550x 400 mm with single

15 mm C.P. brass pillar tap.

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin

including PVC waste fittings complete.

Providing & fixing white vitreous china flat back half stall Urinal of

580x380x350 mm with white PVC automatic flushing cistern with fittings

standard size CP brass flush pipe, spreaders with unions and clamps (all

in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet

grating and other couplings in CP brass including painting of fittings and

brackets cutting & making good the walls & floors wherever required.

17.4.1 Single half stall urinal with 5 liter P.V.C. automatic flushing cistern Each 10.00 6258.75 62,587.50

Providing and fixing 600x450 mm beveled edge mirror of superior glass

45 17.31 (of approved quality) complete with 6 mm thick hard board ground Each 35.00 1607.95 56,278.25

fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm

high and 112 mm distance from wall of standerd shape with bracket of

the same material with snap fittings of approved quality and colour

weighing not less than 105 gms

Digitally signed by AMIT

REPAIR OR GATE AND RAILING

Steel work welded in built up sections/ framed work, including cutting,

47 10.25 hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and

Painting with synthetic enamel paint of approved brand and

manufacture of required colour to give an even shade : Two or more

coats on new work over an under coat of suitable shade with ordinary

paint of approved brand and manufacture

Demolishing cement concrete manually/ by mechanical means

49 15.2 including disposal of material within 50 metres lead as per direction

of Engineer - in - charge.

15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) cum 14.00 2434.25 34,079.50

Providing and laying in position cement concrete of specified grade

50 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

4.1.3 sources : 4 graded stone aggregate 20 mm nominal size Cum 9.00 7878.50 70,906.50

derived from natural sources)

COMMONM MISCELLANEOUS CIVIL WORKS

Providing and fixing double scaffolding system (cup lock type) on the

exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5

m centre to centre, horizontal & vertical tubes joining with cup & lock

system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase

system in the scaffolding for working platform etc. and maintaining it in a

serviceable condition for the required duration as approved and

51 14.72 removing it there after. The scaffolding system shall be stiffened with SQM 240.00 338.25 81,180.00

bracings,runnrs, connection with the building etc wherever required for

inspection of work at required locations with essential safety features for

the workmen etc. complete as per directions and approval of Engineer-

in-charge. The elevational area of the scaffolding shall be measured for

payment purpose. The payment will be made once irrespective of

duration of scaffolding.

Painting (one or more coats) on rain water, soil waste and vent pipes

52 13.96 and fittings with synthetic enamel paint of approved brand and

manufacture and required colour on old work

Digitally signed by AMIT

Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm

and under, including cutting the patch in proper shape, raking out joints

and preparing plastering the wall surface with white cement based

polymer modified self curing mortar, including disposal of rubbish, all

complete as per the direction of

Engineer-In-Charge.

Dismantling precast concrete or stone slabs in walls, partition walls etc.

54 15.40 including stacking within 50 metres

15.40.2 Thickness above 40 mm up to 75 mm SQM 36.00 433.55 15,607.80

Dismantling C.I. or asbestos rain water pipe with fittings and clamps

including stacking the material within 50 metres lead

Dismantling old plaster or skirting raking out joints and cleaning the

56 15.46 surface for plaster including disposal of rubbish to the dumping ground SQM 140.00 54.65 7,651.00

within 50 metres lead.

Chipping of unsound/weak concrete material from slabs, beams,

columns etc. with manual Chisel and/ or by standard power driven

percussion type or of approved make including tapering of all edges,

57 26.28 making square shoulders of cavities including cleaning the exposed

concrete surface and reinforcement with wire brushes etc. and disposal

of debris for all lead and lifts all complete as per direction of Engineer-In-

26.28.1 75 mm average thickness sqm 10.00 378.00 3,780.00

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)

Single socketed pipes.

Providing & Applying polymer modified, flexible cementatious negative

side waterproofing coating with elastic waterproofing polymers on

interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of

self priming of cementatious waterproofing polymer (dilution with water

59 22.23A in the ratio of 1:1) and two coats of cementatious waterproofing sqm 10.00 447.35 4,473.50

polymer (dilution with water in the ratio of 3:1 ) after scrapping and

properly cleaning the surface to remove pre-existing paint film & loose

particles till plaster is visible, complete in all respect as per the direction

of Engineer-in-Charge.

Digitally signed by AMIT

Repair Micro concrete: Application of repair Micro-concrete of M40

grade for Making up lost section of concrete for thickness more than

60 30mm, after the application of bonding agents to ensure stability of the Kg 1500.00 71.98 107,970.00

concrete, followed by curing with water for at least 7 days. The rates are

inclusive of all materials, labour, machinery, equipment, tools, tackles"

Brick work with common burnt clay modular bricks of class designation

7.5 in foundation and plinth in:

6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 6.00 6504.90 39029.40

Carriage of Materials: By Mechanical Transport including Loading,

Unloading and Stacking- Lime, Moorum, Building Rubbish upto 30km

MULTIPLYING FACTOR @0.973 FOR 18 % GST 7,582,532.18

Grand Total of Civil Works 7,934,463.47

Grand Total of Civil Works 7,934,463.47

Digitally signed by AMIT

PLUMBING FIXTURE WORKS

S.No. DSR No. Description of Item Unit Qty DSR RATE DSR AMOUNT NDSR RATE

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1

1 17.16A metre long with S.S. triangular plate to Eureopean type W.C. of quality Nos. 14.00 349.15 4888.10

and make as approved by Engineer - in - charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including

P.V.C. waste fittings complete.

17.28.1 Semi rigid pipe

Providing and fixing CP Waste Coupling for wash basin and sink

3.1 a) CP Waste coupling 31 mm dia of 79 mm length and 62 mm breadth Nos. 4.00 850.00 3400

3.2 b) CP Waste coupling 38 mm dia of 83 mm length and 77 mm breadth Nos. 4.00 1109.50 4438

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at

1.00 m spacing. This includes jointing of pipes & fittings with one step

CPVC solvent cement and the cost of cutting chases and making good

the same including testing of joints complete as per direction of

Engineer in Charge. :Concealed work, including cutting chases and

making good the walls etc.

4.1 18.8.1 15 mm nominal outer dia .Pipes. Metre 18.00 497.8 8960.40

4.2 18.8.2 20 mm nominal outer dia .Pipes. Metre 24.00 537.6 12902.40

Supplying and fixing position the following approved make fittings

& fixtures, including carefully removing the existing old/damaged

fittings & fixtures and

handing over the same

15 mm dia. C.P. Brass bib cock with nozzle wall CP. flange of

5.1 (i) approved equivalent Each 16.00 1003.00 16048.00

15 mm dia. C.P angle valve with wall CP. flange of continental

approved equivalent make.

100mm dia. Heavy quality stainless steel Jali (grating) with or

without holes for waste pipe of floor / Nahani trap etc all complete as

required at site as directed by

Engineer In charge

5.4 (iv) Providing and fixing table mounted sink mixture Each 2.00 7080.00 14160.00

5.5 (v) S/F 450 mm long pvc connection Each 2.00 177.00 354.00

Providing and fixing CP brass Tube spout Faucet complete with flow rate

2.5litre per minute at 3 bar including cutting and making good the wall

where required. (Make: Kohler:Model No Kitchen Faucet:K-99176-IN-4-

CP)(Roca Model No-RT5A847 AC0H) & equivalent Jaguar

Digitally signed by AMIT

S.No. DSR No. Description of Item Unit Qty DSR RATE DSR AMOUNT NDSR RATE

Providing and fixing CP brass 1 Way Bib Cork with wall flange with flow

7 MR - 6 restrictor with flow rate 2.5 liter per minute at 3bar. (Make-Kohler:Model Nos. 2.00 2600.00 5200.00

No's. 1 Way Bib Cork:K-16093 IN-4-CP)(Roca Model No's-RT5A 787ACA1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipe having

thermal stability for hot & cold Water Supply, including all CPVC plain &

brass threaded fitting, including fixing the pipe with clamps at 1.0m

spacing. This include jointing of Pipe & fitting with one step CPVC solvent

cement and testing of joint complete as per direction of Engineer in

43284 25mm Nominal outer dia Pipe Mtr 55.00 401.55 22085.25

43285 32mm Nominal outer dia Pipe Mtr 32.00 518.75 16600.00

Providing and fixing PTMT Bottle Trap for Wash basin and sink: Bottle trap

38 mm single piece moulded with height of 270 mm, effective length of

9 17.70.2 tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth Nos. 12.00 375.65 4507.80

with 25 mm minimum water

seal, weighing not less than 263 gms

Providing and fixing mirror of superior glass (of approved quality) and of

required shape and size with plastic moulded frame of approved make

shade with 6 mm thick hard board backing : Rectangular shape

MULTIPLYING FACTOR FOR GST CORRECTION AS PER DSR 2023 0.973 77218.79

Grand Total of Plumbing Works 146473.25

Grand Total of Plumbing Works 146473.25

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S DSR E&M TOTAL AMOUNT

S DSR E&M TOTAL AMOUNT

DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in

surface/ recessed steel conduit, with modular switch, modular plate, suitable

A.1 GI box and earthing the point with 1.5

sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as

Wiring for group controlled (looped) light point/fan point/exhaust fan point/

call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper

A.2 conductor single core cable in surface/ recessed steel conduit, and earthing

the point with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single

core cable etc. as required.

Supplying and fixing following modular switch/ socket on the existing

1.24 modular plate & switch box including connections but excluding modular

plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 35 ₹136.00 ₹4,760.00

1.24.5 6 pin 15/16 amp socket outlet Each 20 ₹156.00 ₹3,120.00

Supplying and fixing following size/module, GI box along with Modular base

& cover plate on existing modular metal boxes etc. as required.

Digitally signed by AMIT

Supplying and fixing of following sizes of medium

class PVC conduit along with accessories in

1.21 surface/recess including cutting the wall and making

good the same in case of recessed conduit as

Supplying and fixing of following sizes of Mild steel conduit along with

accessories in surface/recess including painting in case of surface conduit,

or cutting the wall and making good the same in case of recessed conduit

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring along with earth wire

with the following sizes of FRLS/HFFR PVC insulated

copper conductor, single core cable in surface/

recessed steel conduit as required.

B.1 1.7.1 2X1.5 Sqmm +1 x1.5 sqmm earth wire Mtre 200 ₹370.00 ₹74,000.00

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 490 ₹476.00 ₹2,33,240.00

1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 200 ₹652.00 ₹1,30,400.00

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in the

C.2 existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following rating, four pole, 415 volts, isolator in the

2.13 existing MCB DB complete with connections, testing and commissioning etc.

Digitally signed by AMIT

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with

2.4 tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without MCB/

RCCB/ Isolator)

Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity

current upto 300 milliamperes in the existing MCB DB complete with

C.5 connections, testing and commissioning etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe of 2.7 Meter long etc. with

charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for

connections etc. as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop

earthing as required.

Dismantling of ceiling fan and painting the same with one or more coats of

spray painting with synthetic enamel paint of approved brand and

D.6 1.59 manufacture to give an even shade, including cleaning of surface with Each 10 ₹324.00 ₹3,240.00

detergent and replacing the damaged rubber reel,

nuts and bolts with washers and safety pins, reinstalling the same as required.

Digitally signed by AMIT

Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation,

Testing and Commissioning of ceiling fan with Brush Less Direct Current

(BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30

cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding,

steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W)

minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total

D.7 9.2 Harmonic Distortion) less than 10%, suitable for operation with regulator for

speed control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise=75 0C (max.), insulation resistance more than 2

mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan

compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core cable and

earthing etc. as required.

1200mm, service value ≥ 6.0 CM/Min/Watt, air

delivery 210 CM/Min (Minimum)

Installation, Testing and Commissioning of exhaust fan in the existing

D.8 1.50 opening, including making good the damage, connection, testing,

commissioning etc. as required.

Supplying and fixing two module stepped type

electronic fan regulator on the existing modular plate

switch box including connections but excluding

modular plate etc. as required.

Digitally signed by AMIT

LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)

Supplying, installation, Testing & Commissioning of LED Recessed/surface

Down lighter (Round/ square/ Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and construction as per IS : 10322

with driver as per the requirement with Driver efficiency >85%,

Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp

range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV

with Short & Open circuit protection ,THD < 10%, P. F.≥0.95, IP20, CRI >80,

UGR (Unified Glare Rating) <19, Flicker free (flicker should be below 5

%), life time (LED, Driver & electrical circuitry), life time of minimum 50000

Burning Hours with 70% of initial Lumen maintained till life ends, CCT

3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard

Deviation Color Matching) <3, Maximum power consumption

should not more than the specified rating and Fixture shall be of relevant

BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/

Screen printing on housing Complete in all respect i/c external

connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor

single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt

output . LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted.. Shape size and CCT shall be as

approved by Engineer-in Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C). Powder coated die cast

/Extruded aluminium

Body including trim .

Digitally signed by AMIT

LED Down lighter (COB Type) (System lumen

efficacy ≥105 < 120 lm/Watt ).

Supplying, installation, Testing & Commissioning of

LED Recessed/ surface Down lighter (Round/

square/ Rectangular) COB Type of following body

material and construction as per IS : 10322 with

driver as per the requirement with Driver efficiency

>85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating

temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with

Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR

(Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life

time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with

70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K

/ 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color

Matching) <3, Maximum power consumption should not more than the

specified rating and Fixture shall be confirming to relevant BIS standards.

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on

housing Complete in all respect i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty. System lumen

efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all

testing required for LED fixtures as per BIS shall

be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of

aluminium housing such that LED junction

temperature shall not rise above 90°C)

Powder coated die cast /Extruded aluminium

Body including trim with Aluminium Reflector

Digitally signed by AMIT

LED Batten light (System lumen efficacy ≥120 <135

Supplying, installation, Testing & Commissioning of

LED surface mounted Batten light of following body

material and construction as per IS : 10322 with

driver (Replaceable) as per the requirement with

Driver efficiency >85%, Operating voltage AC 140 270 Volt, frequency 50/60

hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV

with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,

Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical

circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen

maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per

ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture shall be

of relevant BIS standard. Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. complete

in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy ≥120

<135 lm/Watt output . LM79 & LM80 Test report and all testing required

for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C).

Powder coated die cast /Extruded aluminium

Body (Thickness > 1.20 mm)

Total of Electrical items ₹12,78,063.00

Digitally signed by AMIT