ADDN / ALTN AND IMPROVEMENT TO DRAINAGE AND SANITARY FITTINGS AT CERTAIN VIP AND VVIP CABINS AT WARD ROOM MESS AT INS MANDOVI UNDER AGE (I) MANDOVI

Amount

Dismantling of wall & celling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets.

S&F GI frame work for seamless ceiling of grid size 605x605mm comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 to 30mm and web of 27mm fixed to surrounding wall using nylon sleves and scerews at 450mm centre to centre/ intermediate channel 0.90mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre

S&F Hangers 6mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40x3mm siZe 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified

S&F Seamless calcium silicate ceiling 8mm thick made out of 1800 x 1200 mm size board of siliceous & calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling & tapping screws having Phillips head with under head cutter at 200 mm C/C including finishing the joint of face board with specially formulated jointing compound & 48 mm wide fibre tape to provide seam less finish ( Frame work for ceiling shall be measured & paid separately)

Preparing newaly surface of ceiling and apply two coat of oil bond distemper white or tinted over a coat of alkali resistant primer

Taking down cement plaster of stone /Pcc block /brick wall / top of chajja, or concrete surface of any description including raking out joints hacking for key scrubbing down with water etc and removalof debris to outside of INS Mandovi Area including filling of open joints in cement mortar 1:6 Complete

M & L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brickwork or concrete surface finished even & smooth without using extra cement

M&L distempering walls with two coats of distemper oil emulsion, white or tinted including preparation of new plastered surfaces of wall preparatory to distempering, applying 1mm thick acrylic wall care putty on wall, priming plastered and other surfaces with alkali resistant priming paint

M & L for 15 mm thick (10+5) rendering in cement mortar 1:4 on on fair faces of brickwork or concrete surface in two layers i.e first layer 10 mm thick and 5 mm thick outer layer mixed with WPC as per manufacturer instruction and finished surface even and smooth without using extra cement complete all as specified and directed Note - WPC shall be measured and paid separately

M&L for Preparing new plastered or unplastered surfaces of walls applying two coats of 100%Anti fungal acrylic emlusion exterior grade paint over a coat of acrylic primer in approved shade and as per manufacture instruction including necessary scaffolding etc on newly plastered surfaces incl prepration of surfaces on external surfaces (wall facia cornices etc) complete and directed by Enggineer-in-Chargre (make- asian/Berger/Nerolac/Dulux)

M & L for 5 mm thick plastering in cement mortar 1:3 finished even & smooth, without using extra cement on ceiling

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash

Supply only WPC

Demolition of Brickwork or stone/ boulder masonry, built in cement / lime mortar including all quoins, arches, pillars, etc, for ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling

M & L precast cement concrete solid Block Masonary in PCC 1:3:6 type C1 using 20 mm graded trap aggregate exc 10 cm width and setting in CM 1:6

Dismantling PCC Floor,hearth or wall tiling including cement mortar Bedding, removing serviceable tiles to stores and removing debris to a distance exc 250 m and not exc 1000 m spread and levelled

M&L Screed bed or bedding layer of mortar 20mm thick in CM 1:6 for laying floor finishes

M&L non skid ceramic tiles 7 to 8 mm thick (Square/Rectangular) area of each tile exc 0.11 Sqm but n exc 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for rendering 10mm thick in CM 1:4 for back coating to fixing tiles

Glazed ceramic tiles in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Taking down chowkats with shutters (without taking off shutters from the frames) not exc. 1.5 sq m each

Taking down chowkats with shutters (without taking off shutters from the frames) exc. 1.5 sq m but n exc 4 Sqm each.

S&F 100mm X 63 mm size factory made FRP door frame , frame fixed with 3.Nos on either side with MS flat iron 25mmx3mm cut to size & made to shape & fixed as in hold fast after necessary tarring & sanding & fixed as per manu facture instructions & as directed. Thickness of FRP lamination shall be 2mm. Core shall be polyurethane foam/high density (more than 40kg per cubic meter) cellular foam done in situ. Sscond class wooden blocks shall be provided to hold the fittings .The size of the chowkats shall be inclusive of 2mm thick FRP lamination. Make.Delux/Omega

S&F factory made paneled FRP door shutter , 30 mm thick with 2 mm FRP lamination top rail of size 30 x 150 mm , lock rail & bottom rail of size 30 x 150 mm with 12 mm thick panels of FRP section of box type construction as per IS 4020 core shall be polyurethane foam / high density ( more than 40 Kg per cubic meter ) cellurar foam done in situ & fixed in position as per manufacturer.

M & L Taking down shutters of any description exceeding 1 sqm but n exc 2 Sqm each, easing, adjusting and refixing in the same opening

S&F Extruded aluminium alloy handles, fabricated type, anodized. 200 mm long in size.

S&F for stainless steel hinge, size 100 mm

S & F floor door stopper 150mm long of aluminium alloy body and fixed to door shutter.

S&F aluminium alloy anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt or extruded section or cast aluminum alloy and fixed 300mm size

S&F Aliuminium , anodized barrel tower bolt of extruded section & fixed . 200 mm long in size.

Taking down steel tubing and connections 15 mm bore

Taking down steel tubing and connections 20 mm bore

S & F of CPVC 20mm pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F of CPVC 25mm pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F Stop valve of fancy type chromium type cast copper alloy with crutch or butterfly handle, screwed down, any colour high pressure screwed for iron pipe and fixed fixed in repair (Minimum weight 15mm-90gms/ 20mm- 92gms) in dia 15 mm pipe Code -FON-40053 Make - Jaguar

S & F Bib tap standard of fancy type chromium type cast copper alloy with crutch or butterfly handle, screwed down, any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms).15 mm bore pipe fixed in repair Code -CON-037KN Make - Jaguar

S & F Two way Bib taps,fancy type chromium type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs15 mm bore pipe(Make : Hindware/Jaquar/Cera/Equivalant) Code -FON-041KN Make - Jaguar

S&F 2 in 1 Health Faucet with Hook (Chrome Plated) 1.5 Mtr Tube Make : Make - Jaguar

S&F in repairs Swivel shower of fancy type chromium type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs15 mm bore pipe, 195mm long with bend of 45degree with flange of PTM(Make : Jaquar/Cera / Equivalant )

S&F Chromium plated soap dish approximate size 160 x 160 x 90 mm embedded in wall fixed in repair (Make : Prayag/Jaquar/Cera/Equivalant)

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) (Make : Prayag/Jaquar/Cera/Equivalant)

Disconnecting existing tanks exc 250 litres & n exc 500 litres capacity ,setting aside Cleaning and removing all scales and dirt etc from mouths of circulating pipes etc hoisting if requried, connecting and refixing in position

S&F 500 Litre Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by engr in charge.

S&F Ball valves 25mm bore dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipeand fixed in repairs . (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . /25mm-455gms/ 40mm- 690 gms)

S&F 20mm CPVC Tank Adaptor

S & F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) ( excluding flushing cistern and flush pipe ) fixed in repairs (Make : Prayag/Jaquar/Cera/Equivalant)

S&F 10 litres Capacity PVC valveless,syphonic action type,flushing cistern,low level,white with inlet,ball valve,float and handle including brackets & Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern & fixing only in repair of High or low level fluslhing cistern (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, if any (Make : Prayag/Jaquar/Cera/Equivalant)

S & F Wash basins, Vitreous China (flat back or angle back type) 550mmx400mm size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipefixed in repairs & Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern (Make : Prayag/Jaquar/Cera/Equivalant)

S & F PVC Connection of size 15 mm ,450 mm long with PTMT nuts complete all as specified

S&F 32mm x 800mm long PVC Waste Pipe

S&F Pillar taps fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot and cold with long screwed shanks and flynuts, screwed for iron pipe and fixed in repairs

S & F PVC (SWR) pipes 75 mm bore single sockeyed in any length with rubber rings joints laid in trenches or in floors

S & F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber rings joints laid in trenches or in floors

M&L for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement fixed in repairs

S& F PVC (SWR) bends any radius 110 mm bore

S& F PVC (SWR) bends any radius 75 mm bore

S&F PVC (SWR) junction single, (Single T) equal or unequal 110mm bore with acess door

S&F PVC (SWR) junction single, (Single T) equal or unequal 75mm bore with acess door

S&F PVC (SWR) vent cowl 75mm dia

S&F PVC (SWR) vent cowl 110mm dia

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F aluminum powder coated door/window/ventilator shutter including frame , any type (sliding/open-able/louver ) with frame , & other similar work etc fabricated by using the JINDAL / CENTURY section including necessary arrangement to receive 4mm thick sheet glass or wire mesh with aluminium channel beading & stainless steel screws including the cost of rubber gasket / rubber beading etc complete . But the weight of the rubber gasket / beading will not be measured with weight of aluminium shutter Note :- Sheet glass & wire mesh shall be measured & paid separately

Supply and fix aluminium powder coated grill, 7.5 mm thick

S&F Figured glass 4mm thick, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

S & F aluminium powder coated louvers of 4 handle/blades to fitted in aluminium ventilator of size 0.6m x 0.45m

Dismantling of wooden kitchen cabinet and cupboard fixed in any position

S&F in repair for 18 mm thick marine waterproof ply wood grade BWR, type BB fixed with screws to timber frame work, block boards, grade 2 quality, interior grade, commercial type , fixed with screws to timber framed work for kitchen cabinet,cupboard etc ISI Mark

S&F in repair for 12 mm thick marine waterproof ply wood grade BWR, type BB fixed with screws to timber frame work, block boards, grade 2 quality, interior grade, commercial type , fixed with screws to timber framed work for kitchen cabinet,cupboard etc ISI Mark

S&F in repair for 0.9mm thick decorative laminate type I, of surface finish, colour and pattern as approved , fixed with approved adhesive as per manufacturers instructions.

S & F in repair Continuous (piano) hinges, mild steel, bright finish or electrogalvanised 40mm width

S&F in repair Ball catches with 8 mm dia steel ball, and brass body and strikoing plate including letting in and fixed

S & F in repair Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane 4.8mm thick

S&F in repair for 100 mm long brass handle ,casst type polished bright for cupboard,cabinate ,etc.

M&L for french polishing on wooden surfaces of any description, including cleaning and preparing the old surfaces including a coat of wooden filler on old works with one or more coats

S & F wooden Beading of size 1" x 6mm thick

Dismantling stone slab of any description or thickness in floors, approns etc

M & L For Screed Bed or Bedding Layer of mortar 15 mm thick in cement mortar 1:4 for laying Floor finishes

S & F 20 mm thick granite (of any type) work (table rubbed and polished) as in cooking platform , wash basin platform and like in CM 1:4 including pointing in white cement (1:2) using dust with admixture of pigment to match with shade of granite over cement slurry 20 mm thick in CM (1:6) all as specified and directed

S & F 20 mm thick granite (of any type) work (table rubbed and polished) as in vertical surface (facia ect.) and like all as directed by Engg-In-Charge.

M&L for chamferring and rounding the straight cut edges of stone slab such as in steps, cooking platform and other similar situations complete all as specified

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, wahers and wastes incl bedding in cement mortar on the dwarf wall or incl fixing cantilever brackets and incl all necessay fitting , connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330 mm x 160 mm

S&F in repairs Stainless steel plate utensil rack of size 900 X 600 X 1mm thick, 30cm width and fixed to wall surface with necessary bolts complete all as specified (Make : HINDUSTAN / NIRALI)

S&F in repair 32 mm dia waste fittings, brass chromium plated for glazed ware sinks , WHB with long screwed shanks & fly nuts, flange end .

Excavation in trenches nexc 1.5deep and nexc 1.5m wide in soft/disintegrated rock for foundations etc and getting out

Returning filling in incl spreading, levelling watering and well ramming in layers nexc 25cm in soft/disintegrated rock

Removing excavated material exc 50m and depositing where directed at a level n exc 1.5m above the starting point

Demolition of cement concrete (un-reinforced) of any description and in any position such as in bed for drain pipe etc complete all as directed by Engineer-in-charge

Demolition and breaking up of 150mm/160mm drain pipes (Salt glazed ware/AC/PVC) set in cement mortar

M&L for concrete bed to drain pipe of 160mm dia incl packing under and haunching against the sides of pipes after they are laid and tested in cement concrete type C2 (1:3:6)

M&L PVC (SWR) pipes 160mmsingle socketed, in any length with rubber ring joints, laid in trenches or in floors

M&L, rendering 10 mm thick in cement mortar 1:6 on brick masonry surface finished even and smooth without using extra cement .

Materials and labour for providing cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate in mainholes, surface channels/drain incl necessary form work, finished to required shape all as directed as specified and directed by Engineer-in-Charge.

Materials and labour for pre cast cement concrete (1:2:4) Type B1, using 20mm graded crushed stone aggregates in cover slabs, set in cement mortar 1:4 with plain faces, complete all as specified and directed by Engineer-in-Charge. Note: - Reinforcement steel shall be measured and paid separately under appropriate item of Schedule 'A'.

Supply and fix mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. .

N VENKATESWARLU