Repair/maint to external water supply viz CI, DI, GI pipe lines including connected items at Mil Stn Abohar

Amount

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundations or laying cables/ pipes etc and getting out in soft / loose soil all as specified and directed by Engineer - in - Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers of soft / loose soil not exceeding 25cm thick all as specified and directed by Engineer - in - Charge.

Removal of excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed by Engineer - in - Charge.

Disconnecting electric connections, dismantling/ taking up electric motor 3 phase, 440 volts, 50HZ of capacity 12.5/15 HP, from existing foundation coupled with pumping set, removing to workshop for repair, dismantling/ opening for required repair work including replacement of stainless shafts, ball bearings of motors and pumps (04 Nos.), key rubber shaft coupling, impleller, varnishing, re-assembling and bringing back to installation and making founctional after re-fixing on existing foundation, testing on full load and commissioning complete all as specified and directed by Engineer-in-charge.

Disconnecting electric connections, dismantling/ taking up electric motor 3 phase, 440 volts, 50HZ of capacity 40 HP, 20000 GPH, 60M head from existing foundation coupled with pumping set, removing to workshop for repair, dismantling/ opening for required repair work including rewinding the motor with and including copper winding wire of existing gauge and weight and replacement of stainless shafts, ball bearings of motors and pumps (04 Nos.), key rubber shaft coupling, impleller, varnishing, re-assembling and bringing back to installation and making founctional after re-fixing on existing foundation, testing on full load and commissioning complete all as specified and directed by Engineer-in-charge. Make of winding wire shall be ATLAS/Devi dayal / BPL

Disconnecting electric connections, dismantling/ taking up electric motor 3 phase, 440 volts, 50HZ of capacity 40 HP, 20000 GPH, 60M head from existing foundation coupled with pumping set, removing to workshop for repair, dismantling/ opening for required repair work including replacement of stainless shafts, ball bearings of motors and pumps - 04 Nos. key rubber, shaft coupling, impleller, varnishing, welding, grinding, turning, facing, lathe work, greasing etc. and re-assembling, bringing back to installation and making founctional after re-fixing on existing foundation, testing on full load and commissioning complete all as specified and directed by Engineer-in-charge.

Disconnecting electric connections, dismantling/ taking up electric motor and monoblock pump 3 phase, 440 volts, 50HZ of capacity 20 HP from existing foundation coupled with pumping set, removing to workshop for repair, dismantling/ opening for required repair work including rewinding the motor with and including copper winding wire of existing gauge and weight and replacement of stainless shafts, ball bearings of motors and pumps - 04 Nos. key rubber shaft coupling, impleller, varnishing, re-assembling and bringing back to installation and making founctional after re-fixing on existing foundation, testing on full load and commissioning complete all as specified and directed by Engineer-in-charge. Make of winding wire shall be ATLAS/Devi dayal / BPL

Disconnecting electric connections, dismantling/ taking out non clog / monoblock centrifugal submersible pumping set 3 phase, 440 volts, 50HZ of capacity 5 HP from existing foundation coupled with pumping set, removing to workshop for repair, dismantling/ opening for required repair work including rewinding the motor with and including copper winding wire of existing gauge and weight and replacement of stainless shafts, ball bearings, shaft key, mechanical seal, varnishing, re-assembling and bringing back to installation and making founctional after re-fixing on existing foundation, testing on full load and commissioning complete all as specified and directed by Engineer-in-charge. Make of winding wire shall be ATLAS/Devi dayal / BPL

Disconnecting electric connections, dismantling/ taking out submersible pumping set 3 phase, 440 volts, 50HZ of capacity 15 HP from existing foundation coupled with pumping set, removing to workshop for repair, dismantling/ opening for required repair work including rewinding the motor with and including copper winding wire of existing gauge and weight and replacement of stainless shafts, ball bearings, shaft key, mechanical seal, varnishing, re-assembling and bringing back to installation and making founctional after re-fixing on existing foundation, testing on full load and commissioning complete all as specified and directed by Engineer-in-charge. Make of winding wire shall be ATLAS/Devi dayal / BPL

Run lead joint suitable for 100mm bore spigot and socketed pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

S & F 15mm bore medium grade steel tubes galvanised with all fittings laid in trenches all as specified and directed by Engineer - in – Charge .

S & F 20mm bore medium grade steel tubes galvanised with all fittings laid in trenches all as specified and directed by Engineer - in – Charge .

S & F 25mm bore medium grade steel tubes galvanised with all fittings laid in trenches all as specified and directed by Engineer - in – Charge .

S & F 40mm bore medium grade steel tubes galvanised with all fittings laid in trenches all as specified and directed by Engineer - in – Charge .

S & F 50mm bore medium grade steel tubes galvanized with all fittings laid in trenches all as specified and directed by Engineer - in - Charge .

S & F 80mm bore medium grade steel tubes galvanized with all fittings laid in trenches all as specified and directed by Engineer - in - Charge .

S & F in repairs gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 80mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F in repairs gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 50mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F in repairs gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 40mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F in repairs gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 25mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F in repairs gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 20mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F in repairs gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 15mm bore as in repairs complete all as specified and directed by Engineer – in – Charge.

S & F in repair ball brass valve 20mm bore dia high pressure with polythene float and fly nuts complete screwed with iron pipe and fixed all as specified and directed by Engineer - in - Charge .

Construction of valve pit inside dimensions 90cm x 90cm x 90cm deep from the top of surface including cover of MS sheet 3.15mm thick and angle iron 40mm x 40mm x 6mm with hinges and locking arrangement including painting with two coats of synthetic enamelled paint over a coat of red oxide and grouting to PCC 1:2:4 type B-1, and brick work in CM 1:4, plastering in cement mortar 1:3, foundation concrete 1:3:6 all as per existing pattern and as specified and directed by Engineer - in – Charge. (Earth work shall be measured and paid for separately)

Supplying and fixing as in repairs/replacement sluice valve flanged type rating PN 1.6 size 200mm bore conforming to IS14846 with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supplying and fixing as in repairs/replacement sluice valve flanged type rating PN 1.6 size 150mm bore conforming to IS14846 with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supplying and fixing as in repairs/replacement sluice valve flanged type rating PN 1.6 size 100mm bore conforming to IS14846 with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supplying and fixing as in repairs/replacement sluice valve flanged type rating PN 1.6 size 80mm bore conforming to IS14846 with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supplying, laying, jointing, commissioning and testing DI pipes with Tyton joints of spigot and socket ends centrifugally cast(spun) class " K-9" conforming to IS-8329-2000 in any length of size 100mm bore laid in trench complete all as specified.

Supplying, laying, jointing, commissioning and testing DI pipes with Tyton joints of flanged ends centrifugally cast(spun) class " K-9" conforming to IS-8329-2000 in any length of size 250mm bore laid in trench complete all as specified.

Supplying, laying, jointing, commissioning and testing DI pipes with Tyton joints of flanged ends centrifugally cast(spun) class " K-9" conforming to IS-8329-2000 in any length of size 200mm bore laid in trench complete all as specified.

Supplying, laying, jointing, commissioning and testing DI pipes with Tyton joints of spigot and socket ends centrifugally cast(spun) class " K-7" conforming to IS-8329-2000 in any length of size 150mm bore laid in trench complete all as specified.

M & L for DI fittings confirming to IS-9523-2K for DI Spigot and socketed pipes like bends (any type, radius and angle) straight, taper, bend, increasing, decreasing double socket etc.) tee pieces single branch “Y” junction double branch, cross collars, caps and plugs etc. complete all as specified. Note for DI Fittings :-The weight of the fittings for the purpose of payment shall be actual weight of the fittings or as specified in IS code whichever is less.

M & L petty repairs to water supply line for removing leakage/ blockage of GI pipe 50mm bore by providing gasket/ socket/ tee/ elbow/ bend including washers, nuts, bolts etc. including earth work as required complete including earth work all as specified and as directed by Engineer-in-Charge.

M & L petty repairs to water supply line for removing leakage/ blockage of GI pipe 100mm bore by providing gasket/ socket/ tee/ elbow/ bend including washers, nuts, bolts etc. including earth work as required complete all as specified and as directed by Engineer-in-Charge.

M & L petty repairs to water supply line for removing leakage/ blockage of CI/ DI pipe 80mm to 150mm bore by providing gasket/ socket/ tee/ elbow/ bend including washers, nuts, bolts etc. including earth work and lead joint as required complete all as specified and as directed by Engineer-in-Charge.

M & L petty repairs to water supply line for removing leakage/ blockage of CI/ DI pipe 200mm to 300mm bore by providing gasket/ socket/ tee/ elbow/ bend including washers, nuts, bolts etc. including earth work and lead joint as required complete all as specified and as directed by Engineer-in-Charge.

Suuply and fixing of gilan packing for pump and sluice valve of site 6 mm, 8 mm, 10 mm

Supply and fixing of tire coupling for pump set of size TC-10

Supply and fixing of tire coupling for pump set of size TC-11

Supply and fixing of tire coupling for pump set of size TC-12

Supply and fixing of tire coupling for pump set of size TC-14

Supply and fixing of tire coupling for pump set of size TC-15

Supply and fixing of tire coupling for pump set of size TC-18

Supply and fixing of power conractor AC 3 80 Amp Cat Part No 850181 Make : Indo-asian

Supply and fixing of power conractor AC 3 25 Amp Cat Part No 850135 Make : Indo-asian

Supply and fixing of power conractor AC 3 95 Amp Cat Part No 850191 Make : Indo-asian

Suuplying installing testing and commissionng of fully automatic fixing Star-Delta Starter for submersible motor in steel sheet encloser Model No IHSASAP3-E AC 3 415 V 15 HP/ 11 KW 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make :- Cat part No. IHPASDNC of Havells or equivalent HPL/Indoasian/ L&T/BCH/Siemnes

SUDESH ENTREPRISES

POOJA CONSTRUCTION COMPANY

RANDHIR AND COMPANY

M/S RAJESH KUMAR and CO.

ROYAL BUILDERS