Improvements to the internal roads at Sudhanthira Ponvizha Nagar including approach road from 45 feet main road in Kamaraj Nagar Constituency, Puducherry.

Amount

CODE NO. 2.8.1 - Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil.

Code No.4.1.3 - Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

CODE NO. 4.1.5 - Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- all work upto plinth level -1:3:6 (1 cement:3coarse sand 6 graded stone aggregate 20mm nominal size)

CODE NO. 4.1.10 - Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size).

CODE NO. 4.3.1 - Centring and shuttering including strutting, propping etc. and removal of from for - foundations, footings, bases of columns etc. for mass concrete.

CODE NO. 5.28 - Providing and fixing in position 12 mm thick bitumen impregnated fibre board conforming to IS : 1838 , including cost of primer , sealing compound in expansion joints

CODE NO. 10.25.1 Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in stringers, treads, andings etc. of stair cases, including use of chequered plate wherever required all complete.

CODE NO. 11.3.1 Cement concrete flooring 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate.

CODE NO: 13.16.1 6mm cement plaster of mix 1:3 (1 cement : 3 fine sand)

Code No.15.2.1 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead – nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Code No.16.68 Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand , filling the joints with coarse sand etc. all complete.

Code No.30.38 Desilting the canal by removing silt, slush and debries from the bed of the drain removing the grass , buses etc., complete in unhygenic and foul condition including disposal of the same within an average lead of 1KM without polluting the environment by manual means

Code No.4.1A.1 Construction of granular sub-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 of MoRTH specification, 4th Revision - by plant mix method - for grading I material..

Code No.5.5 Providing, laying and rolling of built-up spray grout layer over prepared base consisting of a two layer composite construction of compacted crushed coarse aggregates using motor grader for aggregates. Key stone chips spreader may be used with application of bituminous binder after each layer and with key aggregates placed on top of the second layer to serve as a base conforming to the line, grades and cross-section specified ,the compacted layer thickness being 75mm. (As per MoRTH specification, 4th Revision)

Code No.6.1.MO Cleaning the existing W.B.M. road surtace including removing of binding material and other foreign matter with wire brushes and small picks, sweeping with brooms or soft brushes and finally dusting with old gunny bags and / or compressed air to receive bituminous treatment. As per clause no 502.4.2 and 503.3.1 of MOST specification.

Code No. 6.2.MO Cleaning of the existing black topped surfaces with brooms, soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. As per clause no 503.3.1 of MOST specification.

Code No. 6.5E.1.MO Providing and applying tackcoat on the prepared surface, heating bitumen in boiler and spraying the bitumen with sprayset fitted on bitumen boiler - on black topped surface bitumen @ 5kg/10sqm.

Code No. 6.5F.1.MO Providing and applying tack coat on the prepared surface, heating bitumen in boiler and spraying the bitumen with sprayset fitted on bitumen boiler - on granular base such as WBM and WMM surfaces not bitumen primed. Rate of application 10kg/10sqm

Code No.6.11B.MO Providing and laying open graded premix carpet 20mm thick on prepared surface in a Single course as wearing course composed of specified size of stone aggregates premix with a bituminous binder in mini hot mix plant 6 to 10 tonne laying manually and rolling with power roller 8 to 10 tonne but excluding cost of primer/tack coat. As per clause no 509 of MOST specification.

Code No. 6.17.MO Providing and applying premixed seal coat type ’B’ comprising of thin application of fine aggregate premix with bitumen binder in mini hot mix plant, carriage manually of mixed material and laying and rolling with power roller 8 to 10 tonne. As per clause no 513 of MOST specification.

Code No.NPSR - Disposal of dismantled materials upto 2Km including loading and unloading etc., as directed by the Engineer-in-Charge