SPECIAL REPAIRS TO BLDG NO P-211, P-04, P-74/03,04,11 AND 12 AT MIL STN SANGRUR UNDER GE (SOUTH) PATIALA

Amount

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

M & L for 15mm thick ( in two layers of 10mm and 5mm thickness) cement pastering in cement mortar 1:4 and mixig the water proofing compound as per manufactures instructions on brick or concrete surface of wall finished fair and even without using extra cement complete all as specified and directed Note : Water proofing compound shall be measured and paid saparately.

M&L 10mm thick cement plastering in cement mortar CM 1:6 finishing the surface even and smooth without using extra cement complete all as specified

Complete removal of existing treatment of any type/description such as distempering work ,internal emulsion etc from internal/external surfaces of walls & ceiling with mechanical means/grinder including removal of material from site complete all as specified and directed.

M&L Preparation of new plastered or unplastered surfaces of walls, two coats of cement base paint all as specified.

M&L Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over all as specified.

M&L Preparation of old plastered or unplastered surfaces of walls, two coats of cement base paint all as specified.

M&L for applying two coats of oil bound distemper over one coat of primer over a coat of 2mm thick wall care putty on new plastered surfaces of walls including preparation of new surface complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over a coat of 2mm thick wall care putty filling complete all as specified and directed.

Preparing of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel pain and one coat of pink primer all as specified and directed.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed.

Supply only integral water proofing compound ISI marked.

Rendering 5mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement all as specified.

Preparation of new plastered or unplastered surfaces applying three coat of white wash on ceiling surfaces all as specified.

Preparing old plastered surfaces of ceilings and applying one coat of white wash in all as specified and as directed by Engineer- in- charge.

Dismantling of brick work built in cement mortar incl all quoins, arches, pillar etc complete all as specified.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified.

M&L for brick work in cement mortar (1:4) using sub class 'B' bricks staight or curved on plan to any raidus but in half thick brick walls

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

All as per srl item hereinbefore but n. exc 1.5 sqm each.

S&F Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with single rebate including necessary fixing lugs, hinges, lock strike plate, complete as specified,size 105x 60mm complete all as specified. ( Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish.

S&F Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with double rebate including necessary fixing lugs, hinges, lock strike plate,complete as specified,size 125x 60mm complete all as specified. ( Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item )

M&L Plain cement concrete (1:3:6) type C-0,using 12.5 mm graded mechanically crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick plain framed (Factory made) Panelled shutters of 2nd class HW with lock rail and panels of 9mm B.W.P commercial ply including beading on the facing side of shutters as per SSR Part I clause No 8.17.5. The size of rail and stiles as per IS 1003 (Part I) kiln seasoned and chemically pressure treated all as specified.

S&F 35mm 2nd class hard wood Glazed and skeleton shutters, 2nd class hard wood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section and fixed complete.

S&F for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts fixed.

S&F Extruded aluminum alloy handles, fabricated type, anodised 150 mm size.

S&F Mild steel butt hinges of size 100mm medium weight cold rolled.

S&F 300 mm long MS rat tail pattern spring hinge (helical door spring) including roller and roller plate, complete all as specified.

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf.

S&F factory made aluminium 50 micron powder coated deco grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified.

Steel cup board shutter made out pressed steel frame of size 75mmx45mmx1.25mm thick with prressed steel shutter 01mm thick Godrej pattern fixed to masonry wall by hold fasts made out of 25x3mm flat iron including mild steel CP hanging rod of 20mm dia with brackets fixed on inner sie of one leaf of shutter and on other leaf provision of mild steel CP peg set of 3 including spray painting with two coats of synthetic enemal paint over one coat of red oxide primer all around on steel surfaces of frame and shutter including taking down existing wooden cup board and making good disturbed portion in CM 1:3 or PCC 1:2:4 all as specified and directed. 1.25 mm thick in frame work, cut to size, holes punched, welding, riveting, turning, bending etc. as require to made it in Godrej pattern complete all as specified and as directed.

S&F 30mm thick PVC door factory made solid panell shutters concisting of frame made out of MS tubes for top and bottom rails, MS frames shall be covered with hit moulded plain coulour PVC 'C' chanel having a PVC sheet strip of 20mm width stuck in side with screws.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixed in opening as per specification and drawing

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S & F Wire netting of galvanised steel wire 1.40mm dia and size of mesh 25mm fixed with wooden beds tinned tacks of wire staples

M&L Preparing of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel pain and one coat of pink primer all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises

M&L 25mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in complete all as specified and directed.

M&Lfor Chequered cement concrete tiles 20cm x20cm x 25mm thick,set, jointed and pointed in neat cement slurry in floors Complete all as specified and directed by Engr-in-Charge

M&L for vitrified floor tiles of area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm 8 to 10mm thick in flooring etc set and jointed in neat cement lurry and pointed in white cement to match over and including 20mm thick screed bed in CM (1:4) laid in complete all as specified and directed.

M&L coloured tiles Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed bed in CM (1:4) laid in complete all as specified and directed.

M&L for anti skid coloured pressed ceramic floor tiles of minimum size 300X300 mm 8 to 10mm thick in flooring etc set and jointed in neat cement lurry and pointed in white cement to match over and including 20mm thick screed bed in CM (1:4) laid in complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), in complete all as specified and directed.

M & L Ceramic tiles 8-10mm thick light colour (Square/ rectangular) polished, area of each tile 600 x 600 mm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over 20mm thick screed/ bedding layer in CM 1:4,all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes icluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330mm x 160mm.complete all as specified and directed by Engr-in - charge.

Taking up or down steel tubing of size15mm bore and removal to store

Taking up or down steel tubing of size 20mm bore and removal to store

Supply & laying of 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 with and incl fittings fixed on walls/ceiling or laying in floors complete all as specified.

Supply & laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 with and incl fittings fixed on walls/ceiling or laying in floors complete all as specified.

S&F mild steel chromium plated 20mm curtain rod with fixing brackets, stops rollerss complete incl fixing brackets, stops etc all as specified & directed as in repair . (For the purpose of mesurement and payment running length of curtain rod only shall be considered.)

Dismantling of brick tiles or terracing tiles single layar on roofs complete att as specified.

Demolation of mud puska on roof any thickness as directed.

Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust, etc complete all as specified and directed.

PCC 1:3:6, type B-0 using 12.5 mm graded stone aggregates as in padding over roof ,minimum thickness at khurra as 50mm maintain a slope of 1:100 using water proofing compound complete all as specified.

Cutting grooves in brick wall ,75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified

PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregates as in roof kerbs or mud stops/ coping etc including weathering slightly rounded or chamferred all as specified.

Providing and laying APP (Atactic polypropylene polymer) modified pre-fabricated five layer water proofing memorene 3 mm thick having weight not less than 3.60 kg/sqm black finished reinforced with non wooven polymer matt fix after applying one coat of cold applied solvant based bituminious primer @ 0,40 ltrs per sqm using botane torch and sealing all joint etc confirming to IS 3488 and cement plaster 15 mm thick in cm 1:3 all as per manufacturer instruction complete all as specified.

M & L cement concrete tiles 20-22 mm thick , type B-1 type (1:2:4) pointed in neat cement slury over 15mm thick sceed bed in CM (1:4) complete all as specified and as directed.

S&f Coolar stand Joist, channel, angle, or tee sections, fixed independently, without connecting plates, conforming to Fe 410-W (Gde-E-250) quality -A

S&F framed work as in doors or gates of angles or other section with gussets plate rails braces etc complete drill for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and incl either hook and hinges or steel hanging door fitting steel sheeting or other covering, running rails and hanging also fastening and fixing complete incl pintel hinges, stops hand made sliding bolts etc conforming to Fe 410-O or Fe 310-O, including taking down old steel gate.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed.

PVC ( SWR) rain water pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete as as pecified including flat iror clamps 25x3mm complete all as specified including taking out old damaged AC rain water pipes.

PVC (SWR) bends of any radius for 110 mmdia rain water pipes with rubber ring joints a complete all as specified.

Dismanteling 500ltr water storage tank.

Rotational moulded polythene water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position incl 20 mm bore ball brass valves high pressure with polythene float and fly nut all as specified in SSR Part-1.

S & F 125mm Brass chromium plated shower rose with arms complete all as specified and directed.

S &F CP stop cock concelled cast copper alloy with crutch screwed down screwed for brass ferrule for 15 mm bore pipe after of any description complete all as specified.

S&F Bib taps for 15 mm dia bore pipe cast copper alloy cromium plated with capstain head screwed down for iron pipe or brass ferrule and fixed all as specified.

S&F Pillar taps hot and cold mixture Cast copper alloy fancy type 15mm bore , with capstan heads chromium plated screwed down high pressure and fixed all as specified.

S&F wall mixer hot and cold mixture Cast copper alloy fancy type 15mm bore , with capstan heads chromium plated screwed down high pressure and fixed all as specified.

S&F Angle stop valve/ Angle valve cast copper alloy chromium plated with capstan head , long shank and cup screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipeafter taking down old stop cock of any description complete all as specified.

S&F 450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes of approved quality complete all as specified and directed,

S&F Viterous china, wash hand basin, white, flat back, size 550x400mm including PVC waste pipe 32mm bore and mild steel brackets, fixed all in repairs, including cutting for or pinning in brackets complete all as specified and directed

S&FTubular towel rail, CP 20mm dia, 60cm long between flanges fixed in repairs.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed by Engineer-in-Charge.

S/F in repairs low level flushing cistern of PVC 10 ltr capicity incl 45cm long PVC connection with brass nut at both ends, 15 dia stop cock cast copper alloy,screwed both ends , high pressure(wt not less than as specified in SSR), PVC flush pipe 32 mm bore complete all as specified and directed.

S&FViterous china ware wash down water closet Orrisa pattern size 580x440mm white with integral foot rests including connection to traps and to flushing pipe, anti syphonage pipe complete fixed in repair.

M&L PCC (1:3:6), 50mm thick as in PCC path/ plinth protection.finished the surfaces even and smooth with out using extra cement

Demolition of reinforced cement concrete of any description (Reinforecement cut as required to facilitate demolition ) complete as directed.

M&L for reinforcement cement concrete (Normal mix )1:1.5:3 Type B1 (20mm graded aggregate) as in slab support on wall , beams and collums in floor roof landing balconies deck slab and in shelves and the like.

M&L for reinforcement cement concrete (Normal mix )1:1.5:3 Type B1 (20mm graded aggregate) as chajja and the like.

TMT bars 6 to 8mm dia and over mild steel as in reinforcement, cut to length bent to shape required including cranking and bending with MS wire (anealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat?forms and like in white cement with admixture of pigment to match with shade of granite stone including grinding and polishing complete laid over and including 15mm thick screed bed or bedding layer in CM(1:4) , in complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Machine cut Kota stone slab flooring 20mm (+2mm) thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S & F mild steel powder coated peg set of 6 fixed to wall with steel screws complete all as specified & directed.

S & F Stainless steel wall mounted kitchen dish rack of size 750mm X600mm X 250 mm as described and specifiede as Engr-in -charge.

S&F PVC enclosed case (cabin type) of size 350mmx450mmx100mm with cover and looking mirror over it with two shelves in it complete all as specified and fixed with screws on wall.

S&F cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints laid in trenches or in floor of 100 mm bore with sand cast paper all as specified

S&F cast iron 100mm sand cast vent cowl with cement joints bore with sand cast paper all as specified

S&F CI floor trap with grating including jointing to waste pipe in neat cement 75 mm dia fixed in cement concrete (1:2:4) type B1.

S&F CI P & S trap with grating including jointing to waste pipe in neat cement 100 mm dia fixed in cement concrete (1:2:4) type B1.

S&F 100mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured)

S&F 100mm Branch pieces, double/cross, T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches

S&F 100mm bore Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof

Demolition of cement concrete any description and any position not otherwise specifically provided (below or above ground level).

PCC 1:2:4 type B 0) using 12.5 mm graded stone aggregate 25 mm thick mixing with WPC as in bedding in sunken portions etc complete all as specified and directed.

Plain cement concrete 1:7:12 mix, type E-2 (using 40mm graded Brick aggregate) as in filling of sunken portion complete all as specified and directed.

Applying three coats of brush bond acrylic based cementitious material of approved quality for sunken portion treatment all as per manufacturer instruction and providing 200 mm micron thick polythene film over 85/25 grade bitumen layer @ 0.5 kg /Sqm all as specified.

Providing 40 mm dia GI pipe medium grade spouts 50 Cm long .

Gun metal globe or gate valves of 20 mm dia with iron wheel head screwed both ends for iron pipe and fixed in repair.

S&F 18 mm thick LEAD FREE PVC celuka ply of both side plain white color fixed with screws, slovent cement/adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufactured's specification complete all as specified and directed.NOTE: not less than 10kg per sqm

S&F 18 mm thick LEAD FREE PVC celuka ply of both side plain of approved color other than white colour fixed with screws, slovent cement/adhesive to make kitchensides top and bottom and shelves inside the cabinets complete as per manufactured's specification complete all as specified and directed..NOTE: not less than 10kg per sqm

S&F 12 mm thick LEAD FREE PVC celuka ply of approved colour, fixed with screws, slovent cement/adhesive to make wall mount kitchen cabinets back and pull out drawer sides complete as per manufactured's specification complete all as specified and directed.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 Kg

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150 mm long matt finished complete fixed in position all as specified

S&F Paino/continuous hinge of size 30 mm stainless steel complete all as specified.

S&F auto closing hinges 35 mm of 0 crank(KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in postion all as specified

Dismantling loose/disintegrated portion of RCC Chajjas, bands, shelves, beams and similar works incl provison of supports if reqd and dubbing with PCC (1 : 1.5 : 3) using 6 to 12 thick graded stone aggregate in any portion of 15mm to 50mm thick and finshing to desired shapes.

Gun metal globe or gate valves of 20 mm dia with iron wheel head screwed both ends for iron pipe and fixed in repair.

PTMT jet spray with 1.00 metre PVC tube , (suitable for European seat) including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F for anodised aluminium door shutter, aluminium section weighting 0.55 kg/m including necessary joining, cleats,glazing clips,rubbber neoprene, packing headls 2 nos in each door hinges anodised aluminium snap beading screw etc including mortice lock with minimum three sets of key complete all as specified.

S&F in repair for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F Sheet glass 5.8 mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane.

S& F vitrious china urinal, half stall type, white including flushing cistern, flush pipe and waste pipe. CP waste coupling complete

S&F 15mm bore self-closing taps, cast copper alloy chro-mium plated screwed for iron pipe and fixed

S&F solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing

M&L for applying acrylic thick wall care putty on internal/external surfaces of walls/ceilings/soffits(thickness vary from1.5to2.5mm as required for desired smoothness and levelling of surfaces in two or more layers)by us ingready made wall careputty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed.

Applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceiling surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

S&F factory made Flush shuttersof 30mm, solid core construction, with block board core and plywood face panels, commercial type on both sides :

Dismantling of asbestos cement sheets [corrugated, semi-corrugated, etc] in roof coverings complete all as specified

S & F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping screws as specified

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws as specified.

S&F MS hollow rectangular/square/circular tubes/pipes of Fe410-W(Gde-E-250) Grade as in frame work for roof/rafter/purline/chajja/trusses/columns/struts etc and like similar items etc. complete all as specified.

S&F for plates /cleats/connplates of Fe410-W(Gde-E-250)quality A etc for frame work all as specified.

Dismantling of wrought timber truss scantling 40Sq.cm and over in section framed work, provided for complete as directed .

Dismantling of wrought timber scantling as in fillets, post rafter , purlins etc under 40Sq.cm in section framed work, provided for complete as directed .

Hard core of broken stone boulders of gauge 40 mm spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface all as directed and specified

Machine pressed precast concrete inter locking paver block any shape and size made of M-35 grade concrete (with grey cement and no pigment) of 60mm thickness with 6mm top layer of anti abrasive material laid over 25mm thick (compacted) fine sieved sand complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets

M&L anodised aluminium snap grid false ceiling of grid size 605x605mm consisting of aluminium main and "T' sections of size 25x35x1.5mm thick and wall angles of size 25x 25x 1.5 mm thick suspended with GI wire suspenders of 6mm dia of suitable length and 8-10 mm thick gypsum board, 60x60 cm size fixed with staples on snap grid complete all as specified and directed.

M& L for 2nd class hardwood wrought scantlings in framed and fixed complete all as specified and directed.

M & L for french polishing on surface of any description width or girth incl cleaning and preparing the surface incl a coat of wood filler on new works with two or moire coats.

S &F 2nd class hard wood boarding in flooring 25mmthick Planed one side, with butt joints and fixed with secret nailed.

Stainless steel gauge wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples or with wooden beads, screws and nuts botls etc. all as directed.

Taking down carefully copper/ aluminium point wiring (light fan socket or power) complete along with fittings such as switches, ceiling roses, Pendants regulators Tube fittings and other Kits & fittings/conduit from surface /wall .Removing the material from work site and making good the disturbed portion/ surface of wall/ floor/ ceiling etc by using cement mortar and colour/ white wash to match with the existing surface / location. (Note ;- Serviceable fitting / fixtures will be reused in the work as directed by Engineer- in-Charge)

Taking down un-serviceable main switch, DB’s insulators, DB for MCB etc of any type and any capacity and further disposal including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) all as directed by Engineer-in-Charge.

Taking down ceiling fan of any descrptions, servicing and repairs of fans as required, fixing back, connecting and testing the fan for its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) all as directed by Engineer-in-Charge.

Taking down exhasust fan of any descrptions, servcing and repairs of fans as required, fixing back, connecting and testing the fan for its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash/paint/distemper wherever required (as per the existing ) all as directed by Engineer-in-Charge.

Taking down elect water heater of any descrptions, servcing and repairs of geyser as required, fixing back, connecting and testing the geyser for its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) all as directed by Engineer-in-Charge.

M & L for point wiring with FRLS PVC insulated unsheathed multi-stranded copper conductor 1.5 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and including rigid non metallic concealed PVC Conduit of suitable size (not less than 20 mm) on wall , surface of ceiling with all fittings, such as tee, bend, elbow, socket etc, including FRLS PVC insulated unsheathed stranded copper conductor 1.5 Sq.mm (nominal area ) single core cable as earth continuity conducter to common earth and connected to earth dolly, complete all as specified, for the following :-

(a) One light/fan point controlled by one 1-way switch

(b) One light/fan point controlled by two 2-way switch

(c) One 3/5 pin socket outlet, 5 Amp on independent board

(d) One 3/5 pin socket outlet, 5 Amp on same board

(e) One bell /buzzer point controlled by one push button on independent board

M&L for point wiring with FRLS PVC insulated unsheathed multi-stranded copper conductor 2.5 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and including rigid non metallic concealed PVC Conduit on wall , surface of ceiling with all fittings, such as tee, bend, elbow, socket etc, including FRLS PVC insulated unsheathed stranded copper conductor 2.5 Sq.mm (nominal area ) single core cable as earth continuity conducter to common earth and connected to earth dolly, complete all as specified and directed by Engineer in Charge.

Dismantling / Taking down existing unserviceable sub main wiring from batten / conduit of any size all as directed. Removing the material from work site and making good the disturbed portion/ surface of wall/ floor/ ceiling etc by using cement mortar and colour/ white wash to match with the existing surface / location.

M &L for sub main surface wiring with PVC insulated unsheathed copper conductor cable of size 6 Sqmm single core through concealed rigid nonmetallic PVC conduit of suitable size (Not less than 25 mm dia) in wall and surface of ceiling including 6 Sqmm PVC insulated unsheathed copper conductor cable for continuous earthing form main earth dolly including making good the disturbed potion of wall. (Note :- Two run of 6 Sqmm copper cable one run of 6 Sqmm copper cable and PVC conduit will be measured as a single length)

Switch Modular type, 6 Amp, 240 Volts , one way complete fixed as in repair all as specified.

Switch Modular type, 6 Amp, 240 Volts , Two way complete fixed as in repair all as specified.

Switch Modular type, 16 Amp,240 Volts , one way complete fixed as in repair all as specified.

Socket outlet, Modular type, 6 Amp complete fixed as in repair all as specified.

Socket outlet, Modular type, 6&16 Amp complete fixed as in repair all as specified.

Bell Push, Modular type, 6 Amp complete fixed as in repair all as specified.

Fan regulator, modular type electronic step type complete fixed as in repair all as specified.

S&F ceiling rose surface bakelite two to three terminal 65x50 mm.

S&F in replacement Tube light fittings LED type 1x20 Watt 4 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable all as specified & directed.

S&F in replacement Tube light fittings LED type 1X10 Watt, 2 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable all as specified & directed.

Supply & fix LED bulk head ,10 W complete all as specified & directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as directed.

S&F LED Bulb 9 watt 230 volt retrofit type complete all as directed.

S&F in bell ding dong operating on AC 230 volt single phase.

S&F MCB DB SPN 8 Way with acrylic double door complete all as specified and directed.

S&F including flushing in wall MCB distribution board vertical TPN 4 way 415 Volts AC double door type sheet steel phosphotised powder painted with bus bar neutral earth bar including provision of MCB TPN, FP 100 Amp conforing to IP 43 as incomer all as complete specified and directed.

S&F MCCB 4 pole 100 Amp 415 volt with breaking capacity of 16 KA complete all as specified and direceted.

S&F MCB SPN 240V 40 Amps C series 10 KA complete all as specified and direceted.

S&F MCB SP 240V 6 to 32 Amps C series 10 KA complete all as specified and direceted.

Taking Down the KWH meter along with wooden board/DB after removing all electrical connection complete all as directed by Engineer in Charge.

Refixing & connecting the same or new serviceable KWH energy meter after wiring complete all as directed by Engineer in Charge.

S&F Sheet metal enclosure factory made of size 20cm x 25cm x 12.5 cm deep box made out of 2mm thick ms sheet with double door with locking arrangement , epoxy power coated holes drilled for cable entries suitable for accomodating electric energy meter including brick/cement works as per site requirement includiing flushing the box in walll and making good the disturbed portion of wall /surface complete all as specified & directed bby Engr in charge.

Taking down old U/S LT UG cable of any size from trenches/pipe/floor/walls complete all as specified.

Supply laying jointing cable XLPE insulated PVC shetahted strip wire armoured 1100 volt 4 core 25 sqmm multi stranded aluminium conductor laid in trenches/wall/ducts etcincluding necessary fixing arrangement such as cable lugs glands etc complete after removing/taking out extg unsv cable to the entire satisfaction of Engr in Charge.

Excavation in trenches n.exc 1.5 mtr deep and n.exc 1.5 mtr wide getting out soil.

Returning filling in including spreading leveling, watering and well ramming in layers

Removing excavated soil to a distance not exc. 50 mtr and depositing where directed

Supply and spreading dry sand in trenches for cushioning of cable

Supply and laying well brunt bricks sub class ‘B’ of size 25 x 12.5 x 7.5 cm.

S&F HDPE pipe of size 50 mm dia complete all as spcifed & directed by Engr-in-Charge.

M & L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2 mtr deep below ground level with top edgw of the plate not less than 1.4 mtr below normal ground level , connected earth wire 4 sqmm by means of bolts nuts check nuts and washers of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit in PCC(1:3:6) type C-1 cast iron frame 50mm thick pre cast RCC(1: 1 1/2:3) nominal mix cover slab reinforced with 8 mm dia mild steel deformed bar 15cc and suitable handle of 10 mm Dia round bar including necesary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc 50m and funnel with watering pipe wire mesh copper lugs etc GI protection pipe of size 15 mm bore including testing complete all s specified & directed by Engr in Charge.

Supply and fixing LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified & directed.

Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete with all accessories required for fixing arrangements all as specified and directed by the Engr-in-charge.

Supply laying jointing cable XLPE insulated PVC shetahted strip wire armoured 1100 volt 2 core 16 sqmm multi stranded aluminium conductor laid in trenches/wall/ducts etcincluding necessary fixing arrangement such as cable lugs glands etc complete after removing/taking out extg unsv cable to the entire satisfaction of Engr in Charge.

NARINDER KUMAR SONS

Aman Enterprises

KG BUILDERS

M/s R.N Construction Co.

S K BANSAL AND CO.