SPECIAL REPAIR TO BLDG NO P 22 330 INF BDE CAMP UNDER GE MH AND RH KHADKI

Amount

Demolition of cement concrete unreinforced of any description and in any position, not otherwise specifically provided for and Material and Labour for cement concrete 1:2:4 type B-0, using 12.5mm graded stone aggregates for filleting, benching, slightly rounding or chamfering on edges, filling undulations / depressions in roof surface, providing concrete platform for tanks wherever required complete all as sepcified and directed.

Taking down / removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and disposal of the same to distance exceeding 50mtr but not exceeding 100mtr as and where directed and Material and Labour for 10 mm thick screeding / rendering in cement mortar 1:3 on concrete roof surface, using Water Proofing Compound @ 3% by weight of cement, surface finished even and smooth without using extra cement complete all as sepcified and directed. Note: Water Proofing Compound shall be measured and paid separately.

Supply only intergral water proofing compound complete all as sepcified and directed.

Material and Labour for Cutting out cracks to "V" section in existing roofs or terracing, cleaning out wetting grouting with cement and sand slurry 1:3 complete all as sepcified and directed

Material and Labour for cleaning the plastered /concrete surface with wire brush and applying water proofing treatment as under:- (a) Apply a uniform coat of primer at 0.70 kg/sqm over cement plaster. (b) 3 mm thick and weighing not less than 3.6 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen - based prefabricated five layer water proofing membrane reinforced with non woven polyester black matt finished over compatible primer at 0.40 Ltr/sqm of required density at 25 degree centigrade 0.87 to 0.89 kg/litre and viscosity 70 to160 cps or cold sticker and torch application of membrane with 10 cm overlap both ways after necessary preparation of surface complete as per manufacturers instructions. (c) Apply two coats of bitumastic - aluminium paint over the membrane.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) complete all as sepcified and directed

Material and Labour for waterproofing treatment to RCC sunken slab complete all as specified below. Make: PIDILITE , Dr Fixit or techno commercial equivalent.

(a) Clean the sunken portion of toilet/Bath/WC/Kitchen thoroughly to remove laitance, dirt , dust etc

(b) Form angle fillet of size 40 mm x 40mm along the junction of wall and floor using polymer modified mortar ("Dr Fixit" Pidicrete URP" or techno commercial equivalent)

(c) Sanitary pipes entering through walls and floor shall be sealed with " Dr Fixit Bathseal Tape" and the gaps to be grouted with non-shrink cementitous grout " Dr Fixit Bathseal Gruot" or techno commercial equivalent . Nahani traps , etc to be fitted securely and the gaps around it to grouted in the same manner.

(d) Apply one coat of a Bitumen- modified polymer coating " Dr Fixit Bathseal Plus" or techno commercial equivalent on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely.

(e) In the remaining area, in dry substrate condition brush & apply first coat of the same coating and further apply second coat when first coat is dry. Extend the coating upto 150mm above the FFL. Above FFL, another cementitious waterproof coating " Dr Fixit Pidifins 2K" or techno commercial equivalent can be further applied right upto 2.1 mtr to waterpoof the shower area also , if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6 to 8 hours and allow to dry completely.

(f) After 2 to 3 days, sunken portion must be overlaid with a 50mm thick concrete M 15 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40mm OD UPVC pipe at the lowest point with 300mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2, complete all as specified and directed.

(g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of approvedd makes such as Dr Fixit, FOSROC , SIKA, MC BUCHEMIE, ROFF complete all as specified and directed.(Note:- Tiling work will be measured and paid separately)

Material and Labour for PCC (1:5:10) type E2 using 40mm graded stone aggregate as in mass concrete or as in sunken portion or floor complete all as specified & directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing coat) complete all as specified and directed.

Material and Labour for 25 mm thick PCC 1 :2 : 4 type B0 ( Using 12.5 graded stone aggregate) as in base of floors complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for colour Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick in CM (1:6) Screed bed or bedding layer of mortar for laying floor finishes complete all as specified and directed.

Ditto all as in item No.11 above but as in skirting /dados including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Material and Labour for colour Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile n exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick in CM (1:6) Screed bed or bedding layer of mortar for laying floor finishes complete all as specified and directed.

Material and Labour for Coloured Glazed ceramic tiles 450X300X7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Demolition of brick work or stone masonry or block masonry built in cement or cement/lime mortar complete all as specified and directed.

Material and Labour for PCC solid block masonry of blocks of type C1 (20mm graded stone aggregate) (PCC 1:3:6) wall exceeding 10cm in width & built in CM (1:6) complete all as specified and directed.

Dismantling of old Granite slab of any description complete all as specified and directed.

Material and Labour for 20mm thick Granite slab machine cut laid over cement screed and jointed with grey cement slurry and pointed with whiteor colour cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete including screed bed 15mm thick in CM 1:4 complete all as specified and directed.

Material and Labour for 20mm thick Granite slab machine cut in dado/skirting over cement screed and jointed with grey cement slurry and pointed with whiteor colour cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete including rendering of 10mm thick in CM 1:4 complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Material and Labour for machine cut kota stone slab flooring 20 to 25mm thick in flooring but one piece as in treads of straircase etc over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, over 15 mm thick screed bed or bedding in CM 1:6 for laying floor finishes complete all as specified and directed.

All as item No 21 here in before but in skirting but one piece for step riser over and incl 10 mm thick rendering in CM 1:4 to receive kota stone/slab etc complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls,ceilings etc. including raking out joints, hacking for key, scrubbing down with water etccomplete all as specified and directed.

Material and Labour for 15 mm thick plastering in cement mortar 1:4 on external surface finished the surfaces (upto 10 mtr height) using 3% of WPC of weight of cement used or as per manufacturer instruction complete all as specified and directed. Note : WPC will be measured separately.

Material & Labour for preparation of new surface and applying / finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Material and Labour for complete removal of existing treatment, preparing the surfaces and applying / finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

ditto all as in item No. 24 above but 10mm thick in CM 1:4 finished even & smooth with thin layer of sagol finish but as in ceiling complete all as specified and directed

Material and Labour for applying three coat of white wash on ceiling including preparation of new surfaces complete all as specified and directed.

Material and Labour for applying one coat of white wash on celing on old surfaces including preparation of old surfaces including cleaning smoke efflorocense of any type or spot of nail filled with putty complete match to old surface complete all as specified and directed.

Material and Labour for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface with a thin layer of sagol complete all as specified and directed.

Material and Labour for preperation of new plastered surfaces & applying two coats of oil bound distember over a coat of alkali resistant primer complete all as specified and directed.

.Material and Labour for complete removal of existing finishes and applying two coats of oil bound distemper on walls over a coat of alkali resistant primer including chalk whiting preparation of old surfaces , on plastered surfaces prepratary to distempering complete all as specified and directed.

Material and Labour for preparation of new surfaces of wall and applying three coats of white wash on walls complete all as specified and directed.

Material and Labour for complete removal of existing finishes and applying three coats of white wash on walls including preparation of old surfaces complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm but n. exc 4.00 sqm complete all as specified and directed.

Supply and Fixing Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, size of frame 125x60mm complete all as specified and directed.

Material and Labour For PCC type C0, 1:3:6 (12.5 mm graded stone aggregate) in door and windows frames, any size, single or double rebated, including arrangement for fixing of hinges and fixtures as required complete all as specified and directed.

Supply and Fixing flush shutters 35mm thick solid core constructions with block board core , ply wood face panels commercial type on both side complete all as specified and directed.

Supplied and fitted to chowkats 35 mm thick factory made 2nd Class Hard Wood Gauzed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); complete all as specified and directed.

Supply and Fixing Aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed.

Supply and Fixing Aluminium handles, cast type, anodised size 150 mm long complete all as specified and directed.

Supply and Fixing 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and Fixing Mild steel Butt hinges100 mm long, medium weight, cold rolled steel complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of width or girth exceeding 10 cm including preparation of surfaces complete all as specified and directed.

Material and Labour for applying one coats of synthetic enamel paint on old wooden surfaces of width or girth exceeding 10 cm including preparation of surfaces complete all as specified and directed.

All as per item No 35 above but size of door n. exc. 1.5.Sqm each.

Taking down shutter from frame exc 1 sqm and n.exc 2 Sqm each and removing from the site complete all as specified and directed.

Supply and Fixing Solid PVC door frame of size 50mm X47 mm made out of 5mm plain colour PVC sheet rinforced with MS Square tube suppling and fixing in opening as per specification and drawing complete all as specified and directed.

Supply and Fixing MS Butt hinges 75 mm long, medium weight, cold rolled steel complete all as specified and directed.

Supply and Fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip if 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bootom rail on either side & as gap insert for top rail and bottom rail ; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles. & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification & drawing complete all as specified and directed.

Supply and Fixing Aluminium, anodised, barrel tower bolts of extruded section 125mm long complete all as specified and directed.

Supply and Fixing Aluminium handles, cast type, anodised size 125 mm long complete all as specified and directed.

Supply and Fixing Powder coated aluminium window sliding type (3 track) with frame size100x35x1.2mm and shutter 39.40x17.70x1.2mm with tow glass shutter & one mesh shutter incl necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm plain float glass & 0.56 mm dia SS wire mesh, fittings etc including taking down old steel window complete all as specified and directed.

Supply and Fixing galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixing to new steel window with nut bolt,fixed complete all as specified and directed.

Material and Labour for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide, primer complete all as specified and directed.

Supply and Fixing Powder coated aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. including taking down existing steel ventilator complete all as specified and directed.

Material and Labour for preparation of old steel surfaces exc 10 cm width or girth and applying one coats of synthetic enameled paint complete all as specified and directed.

Material and Labour for spot welding for repairing steel windows and ventilators hinges, brackets, steel handle, complete all as specified and directed.

Supply and Fixing in repairs powder coated aluminuium pipe 20 mm dia as in curtain rod fixed to brackets complete all as specified and directed. Note brakets shall be measured and paid separately.

Supply and Fixing in repairs powder coated aluminium brakets fancy type for curtain rods of 20mm dia complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed

Taking up or down 15 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required complete all as specified and directed.

Ditto-all as above Item No. 63 but 20 mm dia pipe etc.

Supply and Fixing 15 mm bore of pipe medium grade steel tubes, galvanised with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

.---- do ---- all as per serial item No. 65 above but except steel tubing.

Supply and Fixing 20 mm bore of pipe medium grade steel tubes, galvanised with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply and Fixing in repair rotational moulded polyethylene water storage tanks of capacity 500 ltr hoisted and fixed in position including 25mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Supply and Fixing Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe and fixed in repair complete all as specified and directed

Supply and Fixing in repairs 20mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipes and fixed complete all as specified and directed.

Supply and Fixing in repair angle stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union dia of pipe 15 mm complete all as specified and directed.

Supply and Fixing in repair stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union dia of pipe 15 mm but fancy type with long shank and cup ( concealed type) complete all as specified and directed by Engineer in Charge.

Supply and Fixing in repairs 15mm dia fancy type Bib taps, cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

Supply and Fixing in repair,Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union complete all as specified and directed

Supply and Fixing PVC connections 15 mm size with PTMT nuts of 600 mm long complete all as specified and directed

Supply and Fixing in repairPVC (SWR) pipes 110mm dia ,single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

Supply and Fixing in repairPVC (SWR) pipes 110mm dia ,single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed

Supply and Fixing in repair,PVC (SWR) pipes 75 mm dia ,single socketed in any length with rubber ring joints fixed and laid in trenches or floor complete all as specified and directed.

Supply and Fixing in repair,PVC (SWR) pipes 75 mm dia ,single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed

Supply and Fixing in repair,PVC (SWR) bends any radius,for 110mm dia pipe complete all as specified and directed.

Supply and Fixing in repair,PVC (SWR) bends any radius, 75mm dia pipe complete all as specified and directed.

Supply and Fixing in repair,PVC (SWR) branch piece, single (single Y) equal or unequal,for 110mm dia pipe complete all as specified and directed.

Supply and Fixing in repair,PVC (SWR) branch piece, single (single Y) equal or unequal,for 75mm dia pipe complete all as specified and directed.

Supply and Fixingin repair,PVC (SWR), junction single, (Single T) equal or unequal,for 110mm dia pipe complete all as specified and directed.

Supply and Fixing in repair,PVC (SWR), junction single, (Single T) equal or unequal,75mm dia pipe complete all as specified and directed.

Supply and Fixing in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mmX440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete complete including making good to floor complete all as specified and directed.

Supply and Fixing in repair PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, white/coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed.

Supply and Fixing in repairs vitreous china wash basin white, flat back of size 450mm x 300mm, excluding taps, waste chain & plug & porcelein stopper but including brackets, cutting for and pinning in ends of brackets complete all as specified and directed.

Supply and Fixing in repair pillar taps fancy type cast copper alloy with capestan heads chromium plated screwed down high pressurewith hot &cold with long screwed shanks and fly nuts complete all as specified and directed.

Supply and Fixing in repair ,stainless steel sink, 1mm thick, kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply and Fixing plate rack made of stainless steel 1mm thick and overall size 915mm x915mm x 255mm, inlcuding taking down old /unsv complete all as specified and directed.

Supply and Fixing 20mm dia or over pre polished and moulded granite corner shelf fixed in CM 1:3 to wall and maked good with putty filling with colour match to existing surface complete all as specified and directed by EIC.

Supply and Fixing in repairs tubular towel rail 20mm dia, D type 60cm long between flanges brass chromium plated complete all as specified and directed.

Material and Labour for 75 mm dia cast iron floors trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) (using 20 mm graded stone aggregate), complete all as specified and directed.

Material and Labour for PCC 1:3:6 type C-2 (40mm graded stone aggregate), 75 mm thick as in plinth protection complete all as specified and directed.

Material and Labour for 75mm PCC 1:4:8 type D2 ( 40 mm graded stone aggregates) as ins sub base of floor complete all as specified and directed.

Material and Labour for Prepolished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors with grey cement and pigment including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

Supply and Fixing 1st class Hard Wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together wit glue pinned at joints complete all as specified and directed.

Supply and Fixing in repairs 18-19mm thick Prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Supply and Fixing Hasp and staple 150mm long, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and Fixing 75mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply and Fixing 100mm long Aluminium handles, cast type, anodised complete all as specified and directed.

Supply and Fixing in repairs grating square or circular 125mm dia of PTMT (minimum weight 100 gms, complete all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and 1.50m depth for foundation, etc., for Shaft wells, Manholes etc not exceeding 10sqm on plan and not exceeding 1.50m in depth and getting out in soft / loose soil complete all as specified and directed.

All as per Item No 105 above, but for depth exceeding 1.5m and not exceeding 3.0 m in soft/loose soil.

Returning filling in including spreading leveling watering well ramming in layers not exceeding 25cm thick with soil obtained from excavation complete all as specified and directed.

Demolition and breaking up drain pipes of 150 mm bore RCC/SGSW set in cement mortar including removing the debries to a distance n exc 100mtr, complete all as specified and directed

All as per item No. 109 above but dia of pipe 200mm.

All as per item No. 109 above but dia of pipe 300mm.

Material and Labour for PCC M-7.5 grade nominal mix using 40 mm graded stone aggregate as in concrete bed to drain pipes including packing under and haunching against sides of pipes with concrete after they are laid and bedded dia of pipe 150mm complete all as specified and directed.

All as per item No. 109 above but dia of pipe 200mm.

All as per item No. 110 above but dia of pipe 300mm.

Material and Labour for 150mm dia RCC drain pipes class NP2 laid in trenches and jointed with in cement mortar complete all as specified and directed.

All as per item No. 113 above but dia of pipe 200mm.

All as per item No. 114 above but dia of pipe 300mm.

Material and Labour for cutting to existing manholes for connecting new drain, making good to pipe and rendering, cutting out existing benchings for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for internal dia of pipe 150mm complete all as specified and directed.

Supply and Fixing RCC precast Sewage manhole cover MD grade of size 450mmx900mm thickness 25 to 30 mm and set the same at the site including removing old from site in any position complete all as specified and directed by EIC

Supply and Fixing RCC Precast round Sewage manhole cover MD Grade of size 560mm to 600mm dia thickness 50 to 60 mm heavy duty and set the same at the site including removing old from site in any position complete all as specified and directed by EIC

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors complete all as specified and directed.

Material and Labour for point wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through non metallic rigid PVC conduit and accessories in surface of walls/ceilings including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 1.22 mm thick pressed steel terminal boxes to provision of Modular switches to house switch/regulators etc including Modular Plate and Covers for one fan/light /bell point controlled by one switch/bell push complete all as specified and directed.

All as per item No 120 above but for one 3 pin 5 Amps socket on same board control with other switches on same board

All as per item No 120 above but for one 3 pin 5 Amps socket on independent board

All as per item No 120 above but for for one light point controlled by two way switch complete all as specified and directed.

All as per Item No 120.here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for Power Socket on independent board in Concealed conduit complete all as specified and directed.(09 nos for 15 amp socket + 09 nos for geysers)

Supply and fix switch piano type one 6 amps flush type 240v AC complete all as specified and directed.

Supply and fix modular switch 2 way 6A, 1 module complete all as specified and directed.

Supply and fix bell push, flush type, 5 amp complete all as specified and directed.

Supply and fix socket outlet 2 in 1,3 pin 6A complete all as specified and directed.

Supply and fix socket outlet 2 in 1, 3 pin, 16A flush type complete all as specified and directed.

Supply and fix switch piano type one 16 amps flush type 240v AC complete all as specified and directed.

Supply and fix Modular fan regulator complete all as specified and directed.

Supply and fix electric bell Ding Dong, AC 230 volts complete all as specified and directed.

Supply and fix ceiling rose surface bakelite with three terminals complete all as specified and directed.

Taking down old unserviceable pandent lamp holder & Supply and Fixing PVC/ Polycarbonate type pandent lamp holder with back plate suitable for batten fitting complete all as specified and directed.

Supply & fix LED fitting for Bldg security, 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete. including connecting with 1.5 sq mm copper conductor 3 core flexible cable from fitting connector to ceiling rose and fix on wall with clamps & nut bolts and necessary GI bracket made of 32 mm light grade GI pipe of 1 mtr length with necessary bending complete all as specified and directed .

Taking down old unserviceable tube light fitting and Supply and fixing LED lights fittings 4 feet long, 1x 22 W, 220V,AC, decorative box type with driver, holder incl LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make :- Crompton/Halonix/Bajaj/Wipro

Taking down old unserviceable tube light fitting and Supply and Fixing LED light fitting mirror type with high output diffuser 2 feet, 10 W 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as directed by Engr-in-Charge . Make :- Crompton/Halonix/Bajaj/Wipro

Taking down unserviceable submain wiring and Material and Labour for submain wiring in PVC conduit with two run of 6 sq mm and one runs of 6 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid conduit heavy grade ISI marked (IS 9537 Part III) includung accessories such as bends, supports and chislling/ cutting of wall/ ceiling/ surface, making suitable size of hole through wall/ celling/ surface and making good disturbed surfaces to match the existing surface of walls, floors etc complete all as specified and directed. Note: Two runs of 6 sq mm and one runs of 6 sqmm as earth continuity cable along with conduit shall be measured as one length.

Supply and Fixing MCB DB TPN 4 way of any size and capacity double door type horizontal with 200A busbar including disconnecting from mains and making good the disturbed surfaces complete all as specified and directed. Make :- L&T/ Legrand/C&S

Supply and Fixing MCB DB SPN 8 way of any size and capacity double door type horizontal including disconnecting from mains and making good the disturbed surfaces complete all as specified and directed. Make :- L&T/ Legrand/C&S

Supply and Fixing MCB SP of capacity 6A to 32A "C' curve complete all as specified and directed. Make :- L&T/ Legrand/C&S

Supply and Fixing MCB DP of capacity 32A "C' curve complete all as specified and directed. Make :- L&T/ Legrand/C&S

Supply and Fixing MCB, SPN (Double Pole) 40 amps, 240 Volts, 10 kA ‘’C” curve complete all as specified and directed. Make :- L&T/ Legrand/C&S

Supply and Fixing MCCBs 415v, 16 kA, 4 pole of capacity 63A complete all as specified and directed. Make :- L&T/ Legrand/C&S

Taking down unservicable earthing and Material and Labour for earthing complete with galvansihed steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level connected to 4.0 mm dia galvansihed earth lead wire by means of nuts bolts check nuts and GI washers including PCC pit in PCC 1:2:4 type B-1 (20 mm graded stone aggregate) RCC cover 20 mm dia (medium grade) GI watering pipe with funnel wire mesh and protection pipe of GI of suitbale size upto 7.5 mtr length including charcoal black cotton soil as required at site to achieve the earthing result and common salt & charcoal including , excavation earth work etc in any type of starta complete all as shown in electrical plate No 3 as specified, GI wire suitable size and length for continuity earth wire from test point to main distribution Board complete all as specified and directed. Note: Rate for achieving required depth by compressor machine if required is deemed included in item unit rate.

Material and Labour for taking down existing fan and Supply and Fixing for new ceiling fan, complete with blades, down rods, electronic regulator and accessories,230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) and existing C/F deposited to MES store yard complete all as specified and directed.

Supply and Fixing in repair exhaust fan, steel body AC single phase, 230 V of size 300 mm sweep with, blades, and frame and louvers including chislling/ cutting of wall/ ceiling, making suitable size of hole for exhaust fan through wall and making good disturbed surface of wall/ ceiling to match with existing surface complete all as specified and directed.

Supply and Fixing in repair exhaust fan, PVC body AC single phase, 230 V of size 300 mm sweep with, blades, and frame and louvers including chislling/ cutting of wall/ ceiling, making suitable size of hole for exhaust fan through wall and making good disturbed surface of wall/ ceiling to match with existing surface complete all as specified and directed.

Supply and Fixing in repair Electric storage water heater of capacity 25 ltr of five star rating, AC 230 V with four number nut bolts duly groutted in walls including all standard accessories with flexi connection pipe of 450mm size, glass line tank, NRV complete all as specified and directed.

Taking down the existing serviceable kwh meter from site without any damage cleaning it properly and refixing the same in the new panel as directed by Engr-in-charge of the each block after completion of work complete all as specified and directed.

Taking down existing meter panel box and Supply and Fixing in repair meter panel box indoor type wall mounting of with locking arrangement including powder coating siemens grey shade of size (1200X900X250)mm with sheet thickness not less than 2mm alongwith the provision of MCB SP/SPN/DP - 10 nos , mounting channels & suitable for mounting 10 nos single phase meter complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core including taking out the old cable complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation of poles stays laying of electric cables, pipes etc and getting out in hard/dense soil complete complete all as specified and directed.

Material and Labour for riddled earth for cushioning to under ground electric cable including spreading , levelling and hand punning complete all as specified and directed. Note - Punned thickness shall only be measured & paid .

Material and Labour for Brick " Class B "protection for under ground cable complete all as specified & directed .

Sunrise Traders (BID ID -3313609)

M/S KISHAN CONSTRUCTION (BID ID -3308538)

UNIQUE ENGINEERS (BID ID -3314571)

N AND G CONSTRUCTION (BID ID -3314313)

M/S JAYCONSTRUCTION CO (BID ID -3314505)

ShreHari Civil Enginneering and Contractors (BID ID -3314336)