CERTAIN REVENUE WKS AND CERTAIN MINOR WKS AT LICHUBARI AREA IN JORHAT MIL STN UNDER GE JORHAT.

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil.

Demolition of cement concrete (reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level)

Material and labour for Plain Cement Concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in beams and Lintel Beam complete all as specified and directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in slab complete all as specified and directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in column complete all as specified and directed.

Precast Reinforced Cement Concete cover slab type M-20(Nominal Mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4) complete all as specified and directed.

Precast Reinforced Cement Concete M-20 (20 mm graded aggregate) in precast posts, fencing posts, straining or terminal posts, struts etc. for fencing, average sectional area n exc 100 sq. cm, with or without chamfered angles and flat, splayed, rounded or mitred tops as directed and fixedcomplete all as specified and directed.

Use and waste of formwork to sides of columns

Use and waste of formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves for flat surfaces

Use and waste of formwork to soffits of suspended slabs such as roof slab, floor slabs, landings not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces of concrete.

Material and labour for TMT Bars Fe 500D of 10mm dia & over cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour for TMT Bars Fe 500D 6mm & 8mm dia cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour for High strength steel TMT bars 6 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and labour for Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Material and labour for Precast Reinforced Cement Concete jalli type M-15(Nominal Mix) B-0 using 12.5mm graded stone aggregate, set in Cement Mortar (1:4), 25 mm thick, including all moulding but excluding frame compound complete all as specified and directed.

Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Rendering 5 mm in Cement Mortar 1:3 on fair faces of brick work or concrete ceiling surfaces finished fair

Supply only integral liquid water proofing compound complete all as specified and directed.

Material and labour for Preparation of new plaster wall surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for Preparation of new plaster ceiling surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and applying 2 coats of cement based paint over a coat of alkali based primer of any description over 10 cm girth or width complete all as specified and directed.

Material and labour for Preparation of new wall surface and applying two coats plastic emulsion paint over a coat of primer ver a coat of 1.5 mm thick cement base wall putty on ceiling surfaces of any description over 10 cm girth or width complete all as specified and directed.

Dismantling steel work including gates, rafter, purlin, roof truss etc complete all as specified & as directed.

Rolled mild hollow steel sections steel of grade YSt 310 conform to IS 4923-1997 in roof trusses (framed), trussed, purlins, bracing and fastenings including distance pieces, cleats etc. Note:- The steel trusses shall be provide as per TD no CESZ/STD/26.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material and labour for GI Frame work for seamless ceiling comprising of GI perimeter channel 0.55mmm thick with two unequal flanges of 20 and 30mm and web of 7 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended form soffit at approx 900mm centre to entre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and including 4mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors, sunken floor and paving complete all as specified

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material and labour for75 mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Plain Cement Concrete M-10(Nominal Mix) using 20 mm gaded stone aggregate as in Surface channel and drain

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

Add or deduct for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete complete all as specified and directed.

Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in making good window opening, lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.06 Sqm and not exceeding 0.11Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour of vitrified ceramic tiles,double charged dark coloured shade, 10 mm thick of square/rectangular area of each tile exceeding 0.36 Sqm but not exceeding 0.42 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 15mm thick screed bed layer in CM (1:4)complete all as specified and as directed.

All as per item No 11 here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete

Material & Labour Glazed ceramic tiles 450x300x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Material & Labour of 18mm thick granite ( of any type) work ( table rubbed and polished in pillars and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust admixture of pigment to match with shade of granite over 15mm thick screed bed layer in CM (1:4) including taking down existing one complete all as specified and as directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Material and labour for factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 50x125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp¬ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: 1. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2. M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately

Factory made solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), 2,4, or 6 raised panel design with 2 mm thick Moulded prelam PVC sheet on the front face and 2 mm plain colour prelam PVC sheet on back face supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed..

Supply and fixing Factory made solid panel wire guage PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling wii be wire guage. The wire guage shall be wrappedon an additional square 8 mm MS solid tube.This tube shall be welded to MS tube. The wire guage shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) complete all as specified and as directedincluding taking dwon old one complete all as specified and as directed.

Supply and fixing of aluminium casement window with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and two leaf gauged (fly proofing) sliding shutter. (ii) Opening of windows exceeding 0.90 Sqm but not exceeding 1.50 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CESZ/2015/TD/20 Sheet no 1/2, 2/2 Note Nos :- (i) All window member including fitting & fixture i.e window frame, shutter frame, mullion, clip section, hingh, handle , lock etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass wire mesh shall be measure and paid separately under relevant items of BOQ .

Supply and fixing of sheet glass 4 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing of Glazing with sheet glass (frosted on one side) 4 mm thick ordinary quality with oil putty in square not exceeding 0.5 Sqm in each pane.

Supply and fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Material and labour for Aluminium handles cast type anodised 125 mm size complete all as specified and directed.

Supply and fixing of 300mm ordinary rat tail rod pattern springs including roller and roller plate complete made out of brass complete all as specified and as directed

Material and labour for Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed. Note for item no 57 & 58:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requiredment as as directed by AGE and same shall deem to be included in quoted rate.

Material and labour for Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 15mm bore complete all as specified and as directe

Material and labour for Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore complete all as specified and as directe

Supply and fixing in repair of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -08 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repairs Stop valves fancy type, chromium plated with long shank and cap (concealed type), cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and of size 15 mm bore complete all as specified and directed. Make :- Cat no PIS -28 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS 02 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed. Make: Cat no S2040103 wash basin of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed. Make: CHIVAS of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supply and fixing in repair of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no BS-76 of PRAYAG or equivalent model of make list as given in PS as approved by GE.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 and including taking down existing water tank complete all as specified and directed .

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75 mm dia of outlet complete all as specified and directed.

Cutting into existing manhole for connecting new drain, making good to pipe & rendering, cutting out existing benching for and forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate for 150 mm bore pipe complete all as specified and directed.

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and all as specified in IS 13592 complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.

Supply, laying and testing of 100 mm internal diameter of double wall corrugated(DWC) high density polyethylene pipes (HDPE) and stiffness classes-8 (SN-8) with ISI marked(with CML no) with and including all fitting & jointing material for sewage line and laid in trenches as specified in IS-16098-2013 part-2 complete all as specified and as directed.

Supply and fixing of 8 mm thick frameless toughen glass partition including stainless steel panel hardware complete all as specified and as directed.

Supply and fixing of 8 mm thick frameless toughen glass wall to wall shower enclosure of size 2000x 1950 mm with two fixed and one open able door fixed on side panel including stainless steel panel hardware complete all as specified and as directed. Make:JSE-CHR-OPTSDR1950SX of JAQUAR or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of shower panel 1600 x 200 mm including all necessary fitting and fixtures complete all as specified and as directed. Make: JPL-SSF-ST88158B of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing fancy type chromium plated 15 mm bore stop valve/angle cock cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. Make Cat no AR-39053 of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing of brass chromium plated superior quality single lever tall boy basin mixer 15 mm dia with 150mm extension body & 600mm long braided hoses complete all as specified and directed. Make :- Cat no ARI-39005B of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing of in repair 15mm bore, chromium plated two way bib taps cast copper alloy with crutch or butterfly handle screwed down for iron pipe complete all as specified and directed. Make Cat no ARI 39041 of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing of counter top hung basin vitreous china wash basin white flat back, size 595 x 435 mm including CP waste coupling, bottle trap,with GI pipe brackets & , rag bolt in cement concrete/brick wall and making good wall surface complete all as specified and as directed. Make:-ARS-WHT-39601 of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing in repairs 15 mm dia brass CP fancy basin mixer &Exposed Part Kit of Single Lever Basin Mixer Wall Mounted Consisting of Operating Lever, Cartridge Sleeve, Wall Flange, Nipple & Spout (Compatible with ALD-233N & ALD-235N) for iron pipe and fixed as in repairs complete with making good wall surface complete all as specified and as directed. Make :- Cat no For ARI-39233NK of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing in repairs 15 mm dia brass CP fancy wall mixer 3-in-1 system with L Bend including hand shower with fiexble shower tube1.5m long for mixing hot & cold water screwed down for iron pipe and fixed as in repairs complete with hand shower rose and tube. Make :- Cat no For wall mixter Cat No. 7680 & for Hand shower BH-73 of Paryag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of Vitreous china wash down water closet (pedestal pattern) with concealed S-trap or P-Trap, white, 390 mm high, seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc and including taking down existing one complete all as specified and as directed Mak:-SLICK of HINWARE or equivalent model of make list as given in PS as approved by GE."

Supply and fixing of Toilet paper holder chrome plated complete all as specified and directed. Make Cat no AKP 35753PS of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing of Soap dish chrome plated complete all as specified and directed. Make Cat no AKP-35731P of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing of Soap Dispenser with Glass Bottlecomplete all as specified and directed. Make Cat no CAN-1135N of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing of double arm wall mounted reversible plain / magnifying (X3) pivotal mirror complete all as specified and directed. Make Cat no ACN-1193N of Jaquar or equivalent model of Kohler/Grohe/ROCA

Supply and fixing of Towel shelf/rack chrome plated 24’’ long complete all as specified and directed. Make Cat no CAN-1581H of Jaquar equivalent model of make list as given in PS

Supply and fixing of Glass shelf chrome plated 22" long complete all as specified and directed. Make Cat no AKP-35731P of Jaquar equivalent model of make list as given in PS

Supply and fixing of corner glass shelf chrome plated 22" long complete all as specified and directed. Make Cat no ACN-1173 of Jaquar or equivalent model of Kohler/Grohe/ROCA

Mild Steel angle posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 (Gde E-165) complete all as specified and directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR B/R PORTION (Sl No __ to ____)

Material and labour for concealed point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing complete switch for One light/fan/bell point controlled by one way switch. Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

All as per item no -- here-in-above but One light point controlled by two way two nos switch.

All as per item no ___ here-in-above but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item no ___ here-in-above but above but for one 5 amp socket independent complete all as specified and as directed.

Material and labour for concealed point wiring complete with 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing 3 pin socket outlet 15 Amp independent:- Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Material and labour for concealed point wiring complete with 4.0 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 4.0 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing 3 pin socket outlet 15 Amp independent:- Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Material and labour for point wiring with PVC insulated unsheated stranded copper conductor cable of size 1.5 sq mm in and including PVC cassing caping of required width with all necessary fittings with sunk cast iron /pressed steel terminal box of1.6mm wall thickness and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan/bell controlled by one switch complete all as specified and directed by engineer incharge.

Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.

Supply and fixing of switch piano flush single pole one way 15 amps complete all as specified and as directed.

Supply and fixing of switch piano flush single pole two way 5 amps complete all as specified and as directed.

Supply and fixing of switch socket outlet 3 pin 6/15 Amps 230 volts Universal type complete all as specified and as directed.

Supply and fixing of switch socket outlet 3 pin 6 Amps 230 volts Universal type complete all as specified and as directed.

Supply and fixing in repair bell push flush type 5 Amps complete all as specified and as directed.

Supply and fixing in repair of bell multi music type AC, 230 volts complete all as specified and as directed.

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed. Make : Code no 14502 of Anchor or equivalent model of make list as given in PS as approved by GE.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply , Fixing & testing of Recessed/Surface LED ceiling light fitting 36 Watt of 600mm x 600 mm with LED lamp’s & driver and made of Metallic CRCA powder coated body with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with LED fitting system lumen not less than 100% Lumen per watt and electronic driver with efficiency > 85% with inbuilt protection against lightning, over voltage, short circuit and surge/spike protection upto 5 KV ensuring longer life (THD <10%, PF shall be > 0.95, colour temperature 5700±300 K), Life expectancy of LED's minimum 50,000 burning hrs, warranty of complete luminaries fitting shall not less than three years. The fitting shall be tested LM 79 & 80 and test certificate shall be submitted from original manufacture including connection complete all as specified and directeddirected. Make : Model No LCTLRP 24 FOCDL of Crompton Greaves/ BZRSQL 36L LED GX D WH SD of Bajaj or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repairs of LED 15 watt recessed mounting round down lighter polycarbonate housing with superior light output and integral driver and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. Mm copper conductor flexible wire/cable complete all as specified. Make : Model No LCDEP-15-CDL.of Crompton/ BGSLO SLEEK 15 W WH RD of Bajaj or equivalent model of make list as given in PS as approved by GE

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 10Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 110 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No LDL-10-CDL of Crompton/ BCLSB 10NW of Bajaj or equivalent model of make list as given in PS as approved by GE.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and necessary connecting PVC insulated Flexible cable for connection from ceiling rose to fan and connecting complete all as specified.

Supply and Fixing exhust fan 240V, 300mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed.

Supply and fixing of LED Strip light fittings of capacity 2 W,driver,connector etc incl hanging arrangement including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Havells Cat No LHEHDNP6FN4W002 or equivalent model of make list as given in PS.

Supply, Installation, testing & Commissioning of Stationary storage type electric water heater(Geyser) of capacity 25 Litres with inner tank coated with glass lined coating (Feroglass technology), with high density PUF insulation Shock resistant ABS Body, 4 in 1 multifunctional safety valve, energy efficient BEE 5 star rated and confirming to IS:2082(Part-1), IS 302-2-21 : 2011 other relevant BIS including fixing arrangement and suitable capacity flexible 3 core copper cable of 1.5 metre to 2 metre length necessary connection with and including one PVC Connection pipe of 600mm length for cold water,and one CP flexible Connection pipe of 600mm length for Hot water fixing on walls with and including all necessary fitting material i.e. mild steel Bolts (Bolted to be grouted ). Nuts, Washers etc all as specified and as directed.

Supply and fixing of sub main wiring with two single core 4.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 4.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Supply and fixing of sub main wiring with two single core 6.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 6.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 12 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length complete all as specified and as directed.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 415 volts 10KA breaking capacity.

Material and labour for Earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connetced with earthing wire 4.0mm dia as earthing lead by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 15 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

PEE BEE INDIA

M/S DHAR AND DHAR

AJOY DUTTA CHOWDHURY AND CO

M/S ENGINEERING SYNDICATE

M/S FRONTIER CONSORTIUM