PROVISION OF CHAIN LINK FENCING AROUND BOUNDRY OF ETT AT NDA KHADAKAWASLA

Amount

Earth work in excavation by mechanical means (hydraulic excavator) in foundation trenches or drains n.exc 1.5 mtr in width and not exc 1.5 mtr deep or for shaft,well , cespits, manhole, pier holes etc and getting out in all kind of soil complete all as specified and as directed

Excavation in post holes (or similar holes) each nexc 0.5 cu.m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers nexc 25 cm in soft/loose soil

Demolition of Brickwork or stone/boulder masonry, built in cement mortor including all qoins,arches, pillars etc and precast concrete articles

M&L for plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate ) as in foundation filling & mass concrete.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate ) as in post holes filling & mass concrete.

M&L for RCC 1:1.5:3 type A1 using 20mm graded stone aggregate (nominal mix) as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete.complete all as specified and directed.

M&L for RCC 1:1.5:3 type A1 using 20mm graded stone aggregate (nominal mix) as in columns, pillars, piers, posts and strut and mass concrete complete all as specified and directed.

Use and Waste of Form work to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams etc flat and rough finished faces of concrete complete all as specified and directed.

Use and Waste of Form work to sides of columns, beams, sides and soffits (if any) etc flat and rough finished faces of concrete complete all as specified and directed.

M&L for TMT bars 10 mm dia & over cut to length, bent to shape required, including cranking, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with the clips. complete all as specified and directed.

M&L for TMT bars 5 mm dia & over upto and including 10 mm dia in stirrups,spacers and binders, cut to length, bent to shape required, including cranking, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with the clips. complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing including one shop coat of zinc chromate primer paint using Fe 410-W (Gde E-250) quality B, complete all as specified and directed

M&L for modular fly ash bricks masonry built in CM 1:6 complete all as specified.

M&L for providing cement concrete in copings type B-0 1:2:4 (using 12.5mm graded stone aggregate),including necessary formwork complete all as specified and directed.

M and L for 16-18mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size not exceeding 0.25 sqm fixed with and including making V grove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing and including silicon treatment.

M&L Rendering 15 mm thick in CM 1:6 on surfaces of concrete walls, finished fair and even complete all as specified and directed.

M&L Rendering 15 mm thick backing coat of Dholpur stone in CM 1:4 on surfaces of concrete walls complete all as specified and directed.

M&L Preparation of new plastered surfaces and applying two coats of cement base paint complete all as specified and directed.

S&F 50 mm bore PVC pipes as in weep holes to wall at locations and spacing's specified complete all as specified and directed.

M&L for MS work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 (Gde-E-165) quality complete all as specified and directed

Supply only MS galvenised chain link fencing size 50 mm x 50 mm x 3.0 mm dia

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

M&l for 10 dia round bar horizontally waven in chain link fencing complete all as specified and directed.

S& F for 12 mm dia and 50mm long nut & bolt for fixing flat angle iron complete all as specified and directed.

M&L Preparation of new steel Surfaces of any description, exc 10cm in width or girth, not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide primer.

M&L Preparation of new steel Surfaces of any description,not exc 10cm in width or girth, not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide primer.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in hard dense soil.

Removal of surplus soil/rock to a distance not exc 50 mtrs and depositing where directed at a level not exc 1.5 mtrs above the starting point complete all as specified.

Raj Construction Company

M/s.C.D.Rathod

Sarkar Enterprises

Sunil Constructions

OM GANESH CONSTRUCTION

R & Y CONSTRUCTION COMPANY

Prem Singh

Tejas Enterprises