Construction of Footpath and Installation of Open Gym in Dr. BHIM RAO AMBEDKAR Park in Gaunchi ward no. 02 NIT Faridabad.

Providing and fixing of Knee Chair complete in all respect as per specification KNEE CHAIR Machine Part Description of Knee chair 1. Back Seat 2. Gripper 3. Arm 4. Seat 5. Connector Pipe 6. Oscillator pipe 7. Roller 8. Mounting Plate 9. Center Pillar 10. Cap 11. Round Plate 1 12. Round Plate 2 13. Seat pipe 14. Circlip 15. Pin 1 16.Bearing 17.Metal Cap 18.Rubber Washer 19.Pin 2 20.Locating Strip KNEE CHAIR MECHANICAL DIMENSION AND MEASUREMENT OF MACHINE 1. A circular mounting plate of diameter 233mm and thickness 8mm. 4 eye holes made on this plate at 90 degree which is P.C.D 170mm, hole diameter is 20mm, length is 39.9mm. 2. On circular mounting plate ,a center pillar is welded diameter of center pillar is 114mm and height is 294mm.A round plate 1 is welded on the upper edge of the center pillar having diameter 104mm and thickness 5mm. 3. Seat pipe is welded on the round plate 1 along with the center pillar. It have three parts long straight edge length 366mm, 240mm radius and short length of 150mm bent at an angle of 100 degree from the base. The pipe used is of diameter 60mm and thickness 4mm.Center pillar is welded 239mm apart from the long straight edge of the seat pipe. 4. Locating strips are welded on the seat pipe 154.5mm and 265.5mm from the long straight edge of the seat pipe. Strips having length 55mm, breadth 35mmand thickness 3mm.A hole is made of diameter 13mm and 15mm apart towards the center pillar to locate seat well. Similar measurements for all the strips welded. A plastic seat is fixed on the holes made with the help of Allen bolts (poly drive head). 5. Back seat is located on the short length of the seat pipe with the help of strips welded 5mm above on the center face of the seat pipe and another one is welded 82mm from the seat pipe edge. 6. Arm have five parts length1 189mm,radius 104.4mm,straight length 166.9mm,radius 74mm bent at angle 130 degree,length2 160.8mm. Arm’s length1 edge is welded 205mm from the center of the center pillar and height 318.1mm on both the faces of seat pipe. Grippers are gripped on the length2 of the arm. Grippers used are either of plastic or rubber. 7. On the edge of the long straight edge a pipe of diameter 60mm, length 65mm and thickness 4mm is welded. A pipe of diameter 60mm, length 65mm and thickness 4mm is welded on both the edges of the oscillator pipe. Round plate 2 having thickness 4mm is welded on both sides 13.5mm inwards on edges of the pipe welded on the long straight edge of seat pipe. Round plate 2 have a hole of diameter 28mm. 8. On the upper welded pipe of the oscillator pipe having two bearing fitted, first on the edge and other one is fitted 29mm inwards from the edge of the pipe. Two oscillator pipe having similar mechanism discussed above attached on both sides. A pin having diameter 28mm and length 166mm is welded with the round plates and attached throughout both pipe with the help of bearing, welded along the oscillator pipe. A circlip slot(1.5x2) is made 5mm inwards from both the edges of the pin. Cap is fixed on both the edges of the pin. 9. A round plate is welded 41mm inwards in lower edge pipe of the oscillator pipe. A pin of diameter 28mm and length 227.6mm is welded with the round plate outwards .Plastic Cap is tightly fixed inward. A roller is fitted with the pin having inner diameter 25mm.A washer having diameter 60mm and thickness 5.5mm is fixed in between the roller and the circlip to avoid wearness and maintain the gap along .A circlip slot (1.5x2) is made 6.5mm from the face of the pin and self locking metal cap is fitted on the edge to avoid displacement of the roller. Since metal cap is self locking so that it cannot be detached untill it will not be broken. 10. Short length of the seat pipe has a cap fixed on the open edge .

Providing and fixing of Back Shaper complete in all respect as per specification BACK SHAPER MACHINE PART DESCRIPTION OF ROWER MACHINE 1. RECTANGULAR PIPE 2. BRACKET 3. PIPE-1 4. PIPE-2 5. PIPE-3 6. STOPER BAND 7. RUBBER PAD 8. ANGULAR SEAT BASE PIPE 9. FOOT RESTER JOINT 10. FOOT RESTER 11. BENDING ARMS 12. GRIPPER 13. SEAT 14. BRACKET 15. FOOT RESTER SUPPORT PIPE MECHANICAL DIMENSION AND MEASUREMENT OF MACHINE ARE FOLLOWING 1. A rectangular base pipe having length 1010 mm breath 78 mm and height 40 mm. Three bracket are welded on the rectangular base pipe. 1ST bracket 50 mm ,2nd bracket 65 mm and 3rd bracked 760 mm from the edge of the base pipe. 2. Pipe 1 is arranged with the bracket 1 and having length 342mm and diameter 48mm. 2 bushes are welded on both edges of the pipe1, pipe 2 is also arranged with the bracket 2 and length 349mm and diameter 48mm and bushes are welded with it on both edeges. Similarly 3 brackets are also holding pipe 3having length 342mm and diameter 48mm with bushes welded on both edges. 3. Bending arm pipe welded with the bracket box on both its sides .This arm pipe haves parts, short length 91mm, radius1 121mm, angular length 517mm,radius2 96mm, extended length 140mm.The bending arm are 258mm from the base pipe towards upward. 4. Grippers are studded at the edge of last short straight pipe having material plastic or rubber. 5. Angular seat pipe having parts straight length 1119mm, and angular length 363mm,and having dimensions breadth 78m, above length bracket 1st is welded 88mm form the straight edge of the angular seat base pipe whereas bracket 2nd is welded 528mm from the straight edge of the angular seat base pipe. Each bracket is welded opposite to it. 6. Seat are fixed on the angular seat base pipe with the help of steel Allen bolt (polydrive head). It is of either plastic or metal. 7. Stopper band is also welded with the angular base pipe 334mm from the straight edge of base pipe. Rubber pad is tightened at the ending edge of the stopper band and to avoid shock. 8. Centre of the foot rest pipe is welded with the straight edge of the angular seat base pipe equally. And foot rester is also welded angularly on the foot rester pipe .The diameter of the foot rester pipe 32mm and length 160mm. 9. Foot rester jointers are welded on the foot rester pipe having length 315mm breadth60mmon the either sides of the rester joints, apart 432mm from the edges of the foot rester pipe .Foot rester is joined on the foot rester pipe with the help of polydrive head Allen bolt. 10. Pipe 1 is connected with the bracket 1st of the rectangular base pipe and angular seat base pipe, pipe 2 is connected with the bracket 2nd of the rectangular base pipe and angular seat base pipe, pipe 3 is connected with the bracket 3rd of the rectangular base pipe and another bracket welded on the edge of the (straight) of the angular seat base pipe ,Bushes of all the pipes are joined with the brackets having bearing and pin in between , tightened with Allen bolt polydrive head bolt having plastic caps on the ends. Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.

Providing and fixing of Air Walker complete in all respect as per specification AIR WALKER MACHINE PART DESCRIPTION OF THE AIR WALKER a. Mounting plate b. Center pillar c. Trapezium shaped pipe d. Cap e. Holding pipe f. Hinge supporter g. Obtuse L shaped pipe h. Rectangular pipe i. Standing pad j. Triangular hinge supporter 1. A circular mounting plate of diameter 233mm and thickness 8mm, 4 holes on this plate at 90 degrees of which P.C.D. 170MM. hole diameter is 20mm. 2. On circular mounting plate a center pillar is welded. Diameter of center pillar is 114mm and height is 223mm. 3. Trapezium shaped pipe is welded to the center pillar from the middle at the base. Trapezium shaped pipe’s upper portion is open with two branches. 4. Cap is on the two branches of upper portion/ top of the branches are 925mm wide and length of each branch is 885mm. At the base of the branches the gap is 925mm with a radius bend 235mm. 5. Open end of Trapezium shaped pipe is welded with a holding pipe. Holding pipe has a straight length of 810mm and a 90 degrees radius on both sides, then a small straight length of 246mm. through this small straight length holding pipe is welded to trapezium shaped pipe. Holding pipe is welded at an angle of 40 degrees to the open ends of trapezium shaped pipe, height of joint is 1212mm. 6. Hinge support of length 126mm is welded on the branches of trapezium shaped pipe at a height of 1117mm from the base. 7. 2 obtuse L shaped pipes are connected to the hinge supporter by the bushes. Bushes are welded at the upper portion of the obtuse L shaped pipe. Lower portion of obtuse L shaped pipe is welded with rectangular pipe, of length 705mm, radius 124mm and short length 137mm. 8. On rectangular pipe standing pad are tightly screwed. Standing pad (foot rest) can be of plastic or metal. 9. Triangular hinge supporter are welded to the hinge supporter to provide better strength. Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt poly drive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.

Providing and fixing of Abs Shaper complete in all respect as per specification MACHINE PART DESCRIPTION OF THE ABBS SHAPE a. Circular mounting plate b. Center pillar c. Main pipe d. Square mounting plate e. Frame base pipe f. Frame supporter g. frame h. foot rest i. bending support pipe j. PVC Pad k. Cap 1. A circular mounting plate which has diameter 233mm and thickness 8mm. also has 4 holes at 90 degrees which PCD is 170mm. the diameter of the hole is 20mm 2. In this circular mounting plate , a center pillar is welded. Diameter of the center pillar is 114mm and the height is 568mm. 3. Cap is fixed on the top of the center pillar with rivets. 4. Two main pipes are welded opposite to each other with the center pillar having length 266mm, height from the bottom edge is 174mm and diameter 48mm. 5. Two square mounting plates are welded on the main pipes, apart from the edges of the mounting main pipes 91mm. these plates are of length 190mm, breath 150mm and thickness 5mm 6. A frame base pipe is welded with the square mounting plate at a distance of 14mm from the one of the edge of base pipe having 2 parts, first length straight pipe 108mm and radius 119mm. therefore we have four base pipes welded on the 2 square mounting plate (2x2). Towards the welding, the distance between the two base pipes is 218mm. 7. A foot rest pipe is welded on the radial edge of the 2 base pipes of one square mounting plate. Rest pipes are extended equally from the center. 8. A frame support is welded on the frame base pipe having length 385 mm and diameter 38mm, from the straight edge of the frame base pipe is 84mm. this support pipes are welded on 4 base pipes. 9. A curved frame having a curved radius 2384mm and fliet radius 74mm is welded with the straight edge of the frame base pipe and 2nd side is with the foot rest pipe. Fliet radius is on the four corners of the curved frame. The pipe used to make the curved frame have diameter 32mm. 10. A PVC pad is mounted on the curved frame having same dimensions as of the curved frame, with the help of the mushroom head screws (steel). 11. Bending support is welded on the either side of the center pillar having 3 parts short length 34mm radius 150mm and long straight length 179mm. the bending support is welded 322mm from the center pillar on the main pipe whereas other edge (towards short length) welded with center pillar. Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.

Providing and fixing of Shoulder Shaper complete in all respect as per specification THE SHOULDER SHAPER MACHINE PARTS DESCRIPTION OF SHOULDER SHAPPER • Mounting plate • Centre pillar • 2 hinge holding pipe • 2 bending pipe • Cap • 2 u shapped pipes • Handles • 2 straight pipe(no.-1) • Straight pipe (no-2) • Straight pipe (no-3) • Seat base pipe • Seat bending pipe • Seat • Back seat • Hinge box • Bracket holder 1. A circular mounting plate of diameter 233mm and thickness 8mm. there are 4 holes on this plate at 90 degrees which is P.C.D. 17mm, hole diameter is 20mm. 2. On circular mounting plate a centre pillar is welded. Diameter of the centre pillar is 119mm and height is 1838mm. 3. Cap is fixed on the top of the pillar with rivets. 4. At 1528 mm vertical distance – 2 hinges holding pipes are welded in opposite directions. Hinge holding pipes have clear hole for screw at 177mm distance. 5. Bending pipes are welded to the Hinge holding pipes and the centre pillar to provide mechanical strength to the hinge holding pipe. 6. Hinge box is fitted to the hinge holding pipes with a steel screw and bush. Hinge Box has a clear hole at the base. 7. U shaped pipes are welded at the upper part of the hinge box. 8. At the opening end of the U shaped pipe, handles are fitted with steel screw. 9. Straight pipe no.1 is fitted to the hinge box at the base with Pin bearing. 10. Lower end of the straight pipe no.1 is fitted to straight pipe with a pin bearing. 11. Straight pipe no.2 and no.3 are joined to the centre pillar and seat base pipe one over the other respectively with a gap of 490mm, through bracket jointers, which are welded to the centre pillar and seat base pipe also. 12. Seat base pipe is connected with straight pipe no.2 and no.3 with pin bearings. 13. Over seat base pipe a seat bending pipe is welded. 14. Seat and back seat are fitted on the seat bending pipe with Pin bearing. These seats may be of plastic or steel made. Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.

Providing and fixing of Single Skier complete in all respect as per specification SINGLE AIR SKIER MACHINE PART DESCRIPTION OF SINGLE AIR SKIER a. FOUNDATION RECTANGULAR PIPE b. FOUNDATION CONNECTOR c. STANDING RECTANGULAR PIPE NO.1 d. STANDING RECTANGULAR PIPE NO.2 e. CYLINDRICAL PIPE f. PENDULUM BAR BIG g. PENDULAM BAR SMALL h. BRIDGE RECTANGULAR PIPE i. BRACKET j. STANDING PAD k. BUSH l. HOLDING PIPES m. GRIPERS 1. There are Two Foundation rectangular pipes of length 556mm, breadth 79mm and height 40mm. 2. These 2 foundations rectangular pipes are connected with Foundation connector of length 790mm, breadth 80mm and height 40mm. Foundation connector is welded to both foundations rectangular pipe through the middle of the same pipes. 3. Standing rectangular pipe no.1 of length 930, diameter 89mm is welded to one of the foundation rectangular pipes’ top through the center. 4. Standing rectangular pipe no.2 of length 745mm, diameter 89mm is welded to another foundation rectangular pipe’s top through the center. 5. Cylindrical pipes are welded on the top and center of the both standing pipes. Diameter of cylindrical pipe is 60mm and length is of 457mm. 6. On the both ends of cylindrical pipes 2 pendulum bar big and pendulum bar small are suspended through pin bearing connection. These pendulum bars can swing in forward and backward motion. Length of big pendulum bar is 770mm and length of small pendulum bar is 515 mm. gaps between the 2 pin bearings is 338mm. These pendulum bars are welded to the bush. 7. Free ends of the big pendulum bars and small pendulum bars are welded with bushes. These welded bushes are fitted in the brackets. 8. Bridge rectangular pipe of length 920mm, breadth 40 and height 60mm is connected between one big pendulum and small pendulum bar of same side. 9. Brackets are welded on the both sides of the bridge rectangular pipe for connection of big pendulum bar and small pendulum bar, with steel screws. 10. In the middle of the bridge rectangular pipe standing pads (foot rests) are attached with steel screws. Standing pads may be of plastic or of metal. 11. Holding pipes are welded on the top of the bush of cylindrical pipe. Holding pipe has 3 parts. First straight length of 123mm, radius length 96mm at the angle of 26 degrees, radius at angle 90 degrees and last is straight length 140mm. 12. Last portion of holding pipes are studded with plastic/rubber grippers Note: All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can’t be opened until they will be broken.