Maint of Internal Electrification works for OTM Accn at Faridkot Mil Stn

Amount

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells & making good the disturbed surfaces of walls, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLS with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of switches, sockets, fan regulator etc, covered with 2.8mm thick plastic laminate Hylem / Anchor top cover sheet of required colour, fixed with brass screws and cup washers, painting terminal boxes inside and outside with one coat of red oxide primer including continuous earth wire of size 1.5 Sqmm PVC stranded copper conductor unsheathed, insulated, stranded (Green colour) connected to common earth point dolly for One light point/ fan point/ exhaust fan point to be controlled by one number one way switch complete all as specified and directed .

All as per Srl item No. 02 here-in-before but for one ligh point controlled by two,two way switches complete all as specified and directed

All as per Srl item No. 02 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed

All as per Srl item No. 02 here-in-before but for one switch socket combination, 3 Pin 5 Amps, 230 Volts on independent board complete all as specified and directed

All as per Srl item No. 02 here-in-before but for one bell point controlled by one bell push complete all as specified and directed

All as per Srl item No. 02 here-in-before for switch socket combination (multi purpose) 6 Pin 15 Amps 230 volts point to be controlled by one switch and wiring with 2.5 Sqmm FRLS PVC unsheathed copper conductor and FRLS cable 2.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed .

S&F in replacement PVC Lamp holder with back plate suitable for batten fittings complete all as specified and directed .

S&F in replacement complete set of tube light fitting, 1x20 watt LED (4 feet long), 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed . Havells Cat Part No LUMILINEBS20WLED865SPCWH/Bajaj Cat Part no 830379 20WCDL/Crompton Cat Part No LDLL20-CDL

S&F in replacement complete set of tube light fitting, 1x10 watt LED (2 feet long), 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed . Havells Cat Part No LHEXACP7IN1W010/Bajaj Cat Part no BCLSB 10W/Crompton Cat Part No LDLL10-CDL

S&F in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 220 volt,AC, decorative type driver holder and LED lamp and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed .

S&F in replacement LED light fitting , 10 watt, bulk head luminaires, 220 volt,AC, LED light driver holder and LED lamp and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed .

S&F in replacement ceiling rose, three terminals, PVC polycarbonate, isolated body with bakalite 20mm back plate complete all as specified and directed..

S&F in replacement Submain wiring with two runs of single core PVC FRLS sheathed, insulated, copper cable of 10 Sqmm size, multi stranded, 1100 volts grade with PVC insulated FRLS copper wire 10Sqmm for continous earth wire drawn into and including concealed conduit of suitable size complete all as specified and directed . Note :- Two runs of 10 Sqmm copper cable and one run of 10 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F in replacement Submain wiring with two runs of single core PVC FRLS sheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated FRLS copper wire 6Sqmm for continous earth wire drawn into and including concealed conduit of suitable size complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F switch piano, flush type, single pole, one way, 5/6 Amps, 230 volts, AC supply complete all as specified & directed

S&F socket outlet, two-in-one, 5 pin, 5 Amp, 230 volts, AC supply complete all as specified & directed

S&F switch piano, flush type, single pole, one way, 15/16 Amps, 230 volts AC supply complete all as specified and directed

S&F Piano type switch, single pole, 2 way, 5/6 amps, 230 volt, AC supply complete all as specified and directed

S&F bell push, flush type, 5 amps complete all as specified and directed

S&F Bell, ding dong, AC 230V, single pole complete all as specified and directed

S&F socket outlet ,2 in 1, 5/6 pin, 15/16 Amps, 230 volts ,AC supply complete all as specified & directed

S&F in replacement Sheet metal enclosure for DBs,TPN, double door, 415 Volts, 4 ways, vertical type and space for MCCB complete all as specified and directed .

S&F in replacement Sheet metal enclosure for DBs,SPN, double door, 230 Volts,8 ways with 200 amps rated bus bar complete all as specified and directed .

S&F in replacement MCCB 3 Pole,adjustable type ,415 V, 160 Amps with breaking capacity 36 KA complete all as specified and directed.

S&F in replacement MCB SP 5 to 32 Amp, 230 volts, B Curve with breaking capacity 10 KA complete all as specified and directed

S&F in replacement MCB, SPN, 32 amps, 230V, B Series with breaking capacity 10 KA complete all as specified and directed

S&F in replacement MCB SP 63 Amp, 230 volts, B Curve with breaking capacity 10 KA complete all as specified and directed

S&F in replacement for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, buried directly in ground vertically (depth of pit not less than 2.25m below normal ground level), with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to electrical equipment/GOD/LA and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI medium grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of precast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Schedule Part-I (2009), complete all as specified and directed. Note(s):- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 1000 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) Quoted lump sum / rate shall be inclusive of above all provisions.

S&F in replacement stepped type electronic fan regulator, flush type on the existing pheonolic laminated sheet etc, single phase, AC supply, 230 V and connecting up complete all as specified and directed .

Excavation in trenches in soft/loose soil not exceeding 1.5m deep and 1.5m wide, for foundation etc or manholes,piers,shafts etc not exceeding 10 Sqm on plan and getting out complete all as specified and directed.

Returning, filling in, including spreading, levelling,watering and well ramming in layer not exceeding 25 cm thick complete all as specified and directed .

Removal of surplus excavated soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

Supplying and laying, factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 25 Sqmm, 4 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete including taking out old cable & bricks all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and brick cover for protection of cable shall be measured and paid separately.

S&F in replacement GI pipe, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed. Note : (i) Excavation and earth work shall be measured and paid separately.

S&F in replacement sheet metal enclosure wih socket plug top and MCBs 20 Amp, 240 V, AC Supply, Single Pole and neutral enclosure with a two pin and earth plug with socket complete all as specified and directed .

Supply, fixing and testing LED street / security light fitting of 25 Watt fitted on 4 to 9 meter high octagonal pole / wall/Swan neck pole including LED lamps complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminium alloy. The luminaries shall be monolithic construction, totally enclosed, dust and water proof with minimum IP-65 protection as per IS-10322-1982 (Part-I) with latest amendments and input voltage range 140-300V, AC, frequency 50-60 Hz, PF should be more than 0.9 with total harmonic distoration. THD (I) less than 15%, cool white colour and lamp starting time should not be more than 10 second, Fittings should be provided with 10 KV surge protection. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300V, AC. Driver should also have double phase protection, no load, open circuit and short circuit protection. LED light fittings should be suitable for ambient temperature from - 10 degree centrigrade to 50 degree centigrade and humidity level 10% to 90% RH. Covers should be polycarbonate/ toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficient of LED luminaries system shall be more than 85 lumens per watt and must be certified by LM-79 test report fixed on and including bracket of 32mm dia,light grade ,GI pipe ,1.20 m and connecting with twin core twisted flexible copper conductor cable 1.5 Sqmm including taking down existing one complete all as specified and directed. Note :- (a) Bidder shall submit test report of LED street light fitting from accredited test laboratory for LM-79 (b)Bidder has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. The product will be replaced free of cost in the following cases : - (i) Manufacturing defects (ii) Failure due to mechanical and electrical impact, (iii) Drop in lumen (or lux at 1m) below 90% of claimed values of lumen (or lux at 1m) of the LED/ luminairies. (c) All LED light luminaire must meet the provision laid down in IS-16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part-II/ Section 13 (d) Scope of work shall include supply and fixing street light fittings on poles which includes required T & P and accessories etc if any, making connection, testing etc complete. No extra payment is admissible on these account.

S&F in replacement Modular switch 1 way 16 amps, 1 module complete all as specified and directed.

S&F in replacement Modular socket 6A /16A - 2/3 pin combined, 2 module complete all as specified and directed.

S&F in replacement Modular switch 1 way 6 amps, one module complete all as specified and directed.

S&F in replacement Modular switch 2 way 6 amps, two module complete all as specified and directed.

S&F in replacement Modular bell push 6 amps, one module complete all as specified and directed.

S&F in replacement Modular socket 6A -2/3 pin combined, 2 module complete all as specified and directed.

S&F in replacement modular metal flush box 1/2/3 modules including making good to disturbed area duly matching the colour with existing surface complete all as specified and directed.

S&F in replacement modular metal flush box 4 modules including making good to disturbed area duly matching the colour with existing surface complete all as specified and directed.

S&F in replacement modular metal flush box 6/8 modules including making good to disturbed area duly matching the colour with existing surface complete all as specified and directed.

S&F in replacement Modular white cover plate with frame, 1 module complete all as specified and directed.

S&F in replacement Modular white cover plate with frame, 2 module complete all as specified and directed.

S&F in replacement Modular white cover plate with frame, 3 module complete all as specified and directed.

S&F in replacement Modular white cover plate with frame, 4 module complete all as specified and directed.

S&F in replacement Modular white cover plate with frame, 6 module complete all as specified and directed.

S&F in replacement Modular white cover plate with frame, 8 module complete all as specified and directed.

S&F in replacement mild steel 2mm thick galvanised steel pressed sunken terminal boxes of size 75mmx75mm and 60 mm deep, painted on both sides (inside and outside) with one coat of red oxide primer, for mounting of switches, sockets, fan regulators, etc. including 3mm thick plastic laminated sheet on top, fixed on box with screws and making good to the disturbed surfaces of walls, matching the colour with existing surface complete all as specified & directed.

S&F in replacement mild steel 2mm thick galvanised steel pressed sunken terminal boxes of size 100mmx100mm and 60 mm deep, painted on both sides (inside and outside) with one coat of red oxide primer, for mounting of switches, sockets, fan regulators, etc. including 3mm thick plastic laminated sheet on top, fixed on box with screws and making good to the disturbed surfaces of walls, matching the colour with existing surface complete all as specified & directed.

S&F in replacement mild steel 2mm thick galvanised steel pressed sunken terminal boxes of size 150mmx75mm and 60 mm deep, painted on both sides (inside and outside) with one coat of red oxide primer, for mounting of switches, sockets, fan regulators, etc. including 3mm thick plastic laminated sheet on top, fixed on box with screws and making good to the disturbed surfaces of walls, matching the colour with existing surface complete all as specified & directed.

S&F in replacement mild steel 2mm thick galvanised steel pressed sunken terminal boxes of size 150mmx150mm and 60 mm deep, painted on both sides (inside and outside) with one coat of red oxide primer, for mounting of switches, sockets, fan regulators, etc. including 3mm thick plastic laminated sheet on top, fixed on box with screws and making good to the disturbed surfaces of walls, matching the colour with existing surface complete all as specified & directed.

S&F in replacement condenser 3.15/2.5 Mfd AC 240V, complete all as specified and directed.

S&F in replacement LED luminaire 600mmx600mm,35/36 watt,220 volts,AC, recessed type with high efficiency PMMA diffuser soft glare free light complete with driver,holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified & directed.

S&F in replacement PVC non metallic rigid conduit, 25 mm external dia (medium grade) ISI marked exclusive of boxes but inclusive of all tees, bends, reducer, bell mouth tube ends and fixing accessories, concealed including cutting chases in wall, floor and making good all disturbed surfaces matching with existing surfaces complete all as specified and directed. Note :- A Sum of Rs. 78781.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 21 (Schedule of credit) of Tender Documents.

NAV DURGA CONSTRUCTION CO

NEW AMRITSAR CONSTRUCTION COMPANY

M/s Manoj Construction Co.

GS and Co

DEEPAK ENTERPRISES

Singla Electricals