SPECIAL REPAIR TO BLOCK No D-5 (QTR NO 1 TO 4) INCLUDING SERVANT QTRS AND TOILETS AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Demolition of cement concrete (un-reinforced ) of any description & in any position like sunken floor, roof treatment including cleaning of surfaces by wire brush etc, not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description (like beams, staircases, landing, chajjas, manhole cover, etc) & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of stone slabs, Paving Blocks and stone tiles of any description or thickness laid, bedded and pointed in any mortar as in floors, approaches etc including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush Shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including taking down of grills/guard bars (where occurs) & cutting holes for removing the hold fasts etc, also including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush Shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including taking down of grills/guard bars (where occurs) & cutting holes for removing the hold fasts etc, also including disposing off the debris outsite the premises, complete all as specified and as directed.

Taking down of Aluminium joinery (including chowkat, fittings etc), including taking down of grills/guard bars (where occurs) & cutting holes for removing the hold fasts etc, also including disposing off the debris outside the premises, complete all as specified and as directed.

Taking down Wooden/PVC/Flush shutter of any description, area exc 1.00 Sqm and not exc 2 Sqm each, complete all as specified and as directed.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 10 above but 20 mm bore

All as per item No 10 above but 25 mm bore

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

Taking down PVC SWR Pipes ( any size or pattern) including all fittings, heads, shoes etc, complete all as specified and as directed.

Dismantling water tanks exc 250 litres but not exc 500 litres capacity including disconnecting the connections, complete all as specified and as directed.

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges etc, complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets and existing frame work also, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

M&L for 25mm thick cement concrete type B-0 (1:2:4) (Using12.5 mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

M&L for Light Shade Polished Glazed Vitrified Tiles 9 to 10 mm thick (square/ rectangular), each tile of size 600mm x 600mm as in floor etc, set & jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shalde of the tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Light Shade Polished Glazed Vitrified Tiles 9 to 10 mm thick (square/ rectangular), each tile of size 600mm x 150mm as in skirting etc. on the vertical surfaces, set & jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shalde of the tiles, over and including 10mm thick screed bed in CM 1:3, complete all as specified and directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square / rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for factory fabricated, Hydraulically machine pressed cement concrete designer with glossy finish chequered tiles of size 300x300X20mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM 1:4, tiles joints shall be grouted in CM 1:3 and immediately after grouting, the joints shall be pointed flush in CM 1:3 mixed with pigments to match the colour of the Tiles (in separate process), complete all as specified and directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortar backing coat in CM 1:4, complete all as specified and and as directed.

M&L for coloured tiles of size 600mm X600mm x15 mm thick as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of the tiles including provision of 20mm screed in CM 1:4, complete all as specified and directed. Note : The tiles shall be of make JOHNSON ENDURA : METEOR series or equivalent of make AGL as approved by the GE.

M&L for coloured tiles of size 600mmX600mmX16 mm thick as in skirting,dado and risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of the tiles including provision of 15mm screed in CM 1:4, complete all as specified and directed. Note : The tiles shall be of make JOHNSON ENDURA : METEOR series or equivalent of make AGL as approved by the GE.

M&L for 16 to 18mm thick machine cut, pre-polished Black Jet, premium quality, granite stone slab, in skirting, Kitchen platform, Window cill, dado etc laid over and including 15mm thick CM 1:4 screed bed, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with the shade of granite stone including rounding / moulding the edges half round, complete all as specified and directed.

M&L for brick work with fly ash Bricks, straight or curved on plan to any radius built in CM 1:4 as in half brick thick walls, complete all as specified and as directed

M&L for Pre-cast reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates ) as in landing, cover slabs (for manholes etc), chulla hoods, water trough, shelves and similar article with plain faces including form work, complete all as specified and as directed. Note:- Reinforcement shall be measured and paid for seperately.

M&L for TMT bars 08 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc and applying one shop coat of redoxide primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of fixing lugs, locks strike plate etc and applying one shop coat of redoxide primer, complete all as specified and as directed. Note:- Hinges shall be paid for seperately.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold-fast blocks, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

M&L for the Framed work such as framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F Factory made 35mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type on both sides including provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F Factory made 25mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides icluding provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

S&F Factory made PVC door frame of size 50 x 47 mm with a wall thickness of 5 mm (+0.25mm) Density 600 Kg/Cbm manufactured by a ISO-9001-2015 certificate company , made out of single piece extruded PVC Foam profile, with mitred cut joints and joints with 2 nos of bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, or fusion heat welding process, the vertical door profiles to be reinforced with 33 x 17mm M.S rectangle tube of 19 Guage, the door frame to be fixed to the wall using 8 x 100 mm long anchor fasteners, complete all as per manufacturer’s specifications and as directed. Note :- Door frame shall be water proof, termite proof, elegant and shall have excellent screws holding strength to fix hinges and hold doors properly for a long life.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (Stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face all as shown on drawing at page No 161 of SSR Part-II, complete all as specified and as directed.

S&F standard aluminium powder coated section (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE), as in frame, shutters for doors, windows / ventilators, partitions, kitchen cabinate, kitchen almirah, Fixed/ Open able / side hung/ sliding two or three track or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) Cost of all the items / accessories, Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and wire cloth shall only be measured and paid separately under respective items.

S & F in repair factory made steel windows with side hung shutters including projecting type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, complete all as specified and directed.

All as per item No 41 above but steel windows without glazing bars.

S&F 4mm thick sheet glass of ordinary quality and glazing for Aluminium Joinery or with & including oil putty for steel surrounds or with wooden beading for wooden joinery (cost of wooden beads included in wooden joinery), in squares n exc 0.50 sqm in each pane, complete all as specified and as directed

S&F 4mm thick Figured glass, pin head type and glazing for Aluminium Joinery or with & including oil putty for steel surrounds or with wooden beading for wooden joinery (cost of wooden beads included in wooden joinery), in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including stainles steel wire staples etc, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt 200 mm long of extruded section, complete all as specified and as directed.

All as per item No 46 above, but 150 mm long.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F Floor door stopper (Overall length of cover plate 150mm) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and as directed.

M&L for factory fabricated Hydraulically machine pressed cement concrete tiles of size 300 x 300 x 20mm thick (with gray cement and no pigment), set in neat cement slurry, laid over terrace and roofs etc, including provision of 15mm thick cement screed bedding layer in CM 1:4 mixed with water proofing compound as per manufacturer’s instructions, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in CM 1:3 (in separate process) mixed with water proofing compound as per manufacturer’s instructions, complete all as specified and as directed (Note: waterproofing compound will be measured and paid separately as supply only).

M&L for 18 to 19mm thick plywood grade BWP (Termite treated & boiled water proof), type BB, fixed with & including screws to timber/iron frame work (Make Greenply/kit ply) duly pasted with approved adhesive 0.9mm thick decorative plastic laminated sheet type-1on both sides of plywood, of surfaces finish coloured and pattern as approved for cupboard, kitchen shelf etc, complete all as specified and as directed.

S&F in repairs vitreous china wash wall hung basin, 1st quality of size 200 x 540 x 390mm with & including full pedestal, 32 mm dia brass chromium plated waste fittings, 32mm bore PVC waste pipe 610 mm long and MS brackets, complete all as specified and as directed, (CAT No CNS-WHT-WB04 FOR BASIN AND CNS-WHT-1508 for Full PEDESTAL of Make Jaquar or equivalent of make of CERA/Parryware as approved by GE).

S&F in repairs sink made of 0.80 mm thick sheet of stainless steel (Bronze range super steel 204) for kitchen or laboratory with and including plugs, washers, wastes; 40mm bore PVC waste pipe, also including bedding in cement mortar 1:3 on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall size 460mm x 535mm x 203mm with bowl size 460mmx 394mm x 203mm of Cat No 920-D of Make- Prayag or equivalent of make as mentioned in Appx “B” of Particular Specifications as approved by GE, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Down Water Closet (Pedestal Pattern), 1st quality, of make JAQUAR; CAT No CNS-WHT-WH10 or equivalent of Make CERA/Hindware (Italian collection) as approved by the GE, (excluding flushing cistern & flush pipe), including water closet seat & cover and mild steel CP or aluminised hinging device, making connections, complete all as specified and as directed.

S&F in repair brass towel rail, CAT No BA-70 of Make- Prayag or equivalent of make Jaquar, as approved by the GE, complete all as specified and as directed.

S&F in repairs Overhead Shower 8’’ x 8” mm size with and including shower arm, also including fixing to 15mm steel pipe or union, CAT No- MSR-1170N for over head shower and CAT No- MRX-2140 for shower arm of Make-MARC or equivalent of make Jaquar, as approved by the GE, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repairs bib cock with flange, fancy type, cast copper alloy, chromium plated, screwed for iron pipe or brass ferrule of 15 mm bore, CAT NO- MOR-1020 A of make Marc or equivalent of make Jaquar as approved by the GE, complete all as specified and as directed.

S&F in repairs bib cock, 2 in 1, fancy type, cast copper alloy, chromium plated, srewed for iron pipe or brass ferrule of 15mm bore, CAT NO- MOR-1380 of make Marc or equivalent of make Jaquar as approved by the GE, complete all as specified and as directed.

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated with long shank and cup (concealed type), screwed down, high pressure, screwed both ends for iron pipe or for unions of 15 mm bore, CAT NO- MOR-1040 of make Marc or equivalent of make Jaquar as approved by the GE, complete all as specified and as directed.

S&F in repairs angle valve with flange, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions of 15 mm bore, CAT NO- MOR-1060-A of make Marc or equivalent of make Jaquar as approved by the GE, complete all as specified and as directed.

S&F in repairs Pillar taps, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, CAT NO- MOR-1010 of make Marc or equivalent of make Jaquar, as approved by the GE, complete all as specified and as directed.

S&F in repairs PVC connection of 450 mm length including brass nuts, complete all as specified and as directed.

S&F in repairs 32mm dia Low density polyethylene (LDPE) pipes of pressure rating 6kgf/sq. cm, complete all as specified and as directed.

S&F in repairs for 75 mm bore out let cast floor trap with and including grating, also including jointing to waste pipe and provision of cement concrete type B-1 (1:2:4) block of required size for fixing, complete all as specified and as directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with and including solvent cement, complete all as specified and as directed.

S&F 15mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, fixed partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, also including cutting chases of the required size and making good the same after fixing of the pipes in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per item no 70 above but 20 mm bore pipes.

All as per item no 70 above but 25 mm bore pipes.

S&F rotational moulded polyethylene water storage tank 500ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 25mm bore (Minimum weight 455 grms), complete all as specified and as directed.

S&F in repairs, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and as directed.

S&F in repairs, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 25 mm bore, complete all as specified and as directed.

S&F in repairs 75 mm bore, Cast iron soil, waste and vent pipes (spun pipes), in any length with ears with and including cement joints, laid in trenches or in floors or fixed to wall vertically (also including suitable clamps for fixing of the pipes with the wall etc), complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid for separetly.

S&F in repairs 100 mm bore Cast iron soil, waste and vent pipes(spun pipes), in any length with ears, with and including cement joints, laid in trenches or in floors or fixed to wall vertically (also including suitable clamps for fixing of the pipes with the wall etc), complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid for separetly.

S&F in repairs 75mm bore cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and as directed.

S&F in repairs 100 mm bore cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and as directed

S & F 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, complete all as specified and directed. Note :- Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM 1:3 to match with the existing surfaces.

S&F 110mm bore PVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - B] as in main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plate, framing for cladding, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

S&F Decorated PVC False ceiling of size 600mmX600mmX5mm (+ 0.25mm) thick plain PVC sheet of density 600 Kg/Cum of the specified make, used as a panel insert in a frame work made using powder coated aluminum T-section of size 25mm x 25mm of 19 guage or 1mm thick in square pattern of grid size 600mm x 600mm. The aluminum frame work shall be supported from the ceiling by providing of J Hook or 4 mm dia GI wire of required size to maintain the proper levels etc as directed. The aluminum frame work shall be supported on side wall with the use of powder coated aluminum Angle section of size 25mm x 25mm of 19 gauge or 1mm thick angles etc. complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:4 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:6) on the surfaces of brick work or concrete, finsihed even and smooth (without using extra cement), complete all as specified and as directed.

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings, Chajja kerbs, roof padding/staging of water tank, fixing of GI pipe between wall & MCBDB, etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.00 kilogram of cement per square metre over roof surfaces & sunken floors etc, providing 20 mm thick plastering in cement mortar 1:4 mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

Supply only liquid water proofing compound, complete all as specified and as directed.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying 4mm thick APP modified water proofing polymeric membrane reinforced with non woven polyester fibre using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 4.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption,% - Not more than 0.15. (ix) Cold flexibility - (-) 50C. (x) Dimentional stability % change = Maximum 1%. (xi) Heat Resistance - Does not dirp at 1200 C Note : The quoted rate shall also be deemed to include for cutting grooves of size and shape as required in the parapet wall for tackling the APP membrane in the wall including making good the surfaces of groove & damaged surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane, complete all as specified and directed.

M&L for applying evenly bituminous tack coat @1.20Kg/Sqm of industrial bitumen blinded with 0.006 cum of coarse sand per sqm on the surfaces of the sunken floor, complete all as specified and as directed.

M&L for cement concrete 1:5:10 type E-2 using 40mm graded brick aggregates as in sunken portion of WC etc, complete all as specified and as directed.

M&L for preparing surface of steel and iron work, new or old, ends of posts, back of chowkhats etc area tarred exc 0.10 sqm and not exc 0.50 sqm each and treated with tar or coal tar or black paint, complete all as specified and as directed.

M&L for preparing new plastered surface of ceiling and applying three coats of white wash, complete all as specified and as directed.

M&L preparing old plastered surface of ceiling and applying one coat of white wash, complete all as specified and as directed.

S&F stainless steel zero crank hinges (auto) fancy type (with Euro concealed hinges) of standard size and shape for kitchen cupboard etc, Make :- Godraj or equivalent as approved by GE, complete all as specified and as directed.

M&L for preparing new plastered surface of walls, applying two coats of Birla/Asian wall care Putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of Birla/Asian wall care Putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed

M&L preparing new plastered surfaces of walls and applying two coats of exterior emulsion weather coat paint over one coat of primer, complete all as specified and as directed.

M&L for complete removal of existing treatment from the surfaces of walls and applying two coats of exterior emulsion weather coat paint over a coat of primer including preparation of surfaces, complete all as specified and as directed.

M&L preparing new wooden surfaces of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F Hard drawn steel wire fabric in available size weight not exc 4.00 Kg /sqm for the tank caging etc including welding, riveting, framing etc, complete all as specified and as directed.

S&F in repair wall mixture with & including 115mm long bend pipe on upper side of 15mm bore for fixing of overhead shower, connecting legs and wall flanges, CAT No. MOR-1141, MAKE : MARC or equivalent of Jaquar make as approved by the GE, complete all as specified and as directed.

S&F in repair sink mixture with swivel spout for 15mm bore, wall mounted with connecting legs and wall flanges, CAT No. MJN-1160, MAKE Marc or equivalent of Jaquar make as approved by the GE, complete all as specified and as directed.

S&F in repair centeral hole basin mixture with bradied hoses of 15mm bore, CAT No. MJN-1100, Make- Marc or equivalent of Jaquar make as approved by the GE, complete all as specified and as directed.

S&F in repair single towel rail 600 mm long, CAT No. ACN1111NM of Make Jaquar or equivalent of Marc make as approved by the GE, complete all as specified and as directed.

S&F in reapir soap dish holder, CAT NO ACN-1131N, Make Jaquar or equivalent of Marc make as approved by the GE, complete all as specified and as directed.

S&F in repair toilet roll holder with Flap, CAT No. ACN-1153N, Make-Jaquar or equivalent of Marc make as approved by the GE, complete all as specified and as directed.

S&F in repair glass shelf 600 mm long, CAT No. ACN-1171N, Make-JAQUAR or equivalent of Marc make as approved by the GE, complete all as specified and as directed.

S&F in repair hand shower (Health Faucet) ABS Body with 8 mm dia, 1.20 metre long flexible tube & wall hook, CAT No. ALD-CHR-583, MAKE-JAQUAR or equivalent of Marc make as approved by the GE, complete all as specified and as directed.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates ) as in Beams, cantilevers, bressumers, lintels over 1.5 metre span, complete all as specified and directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates ) as in Chajjas, complete all as specified and directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in slabs supported on walls, beams and and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in columns, pillars, piers, posts and struts , complete all as specified and as directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc and mass concrete, complete all as specified and as directed. Note:- Reinforcement and Form work shall be measured and paid for seperately.

Use and waste of formwork to Beams, cantillevers, bressumers, lintels, shelves and similer items for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similer items including edges for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste of formwork to soffits of suspected slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizonal or slopping) for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, (vertical or to batter) for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide, sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat concrete surfaces, complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

S&F in repairs stainless steel derocative curtain rod of 25mm bore with wood finishes, complete all as specified and directed.

S&F brackets and funnel caps suitable for the curtain rod to be provided under Item No. 99 above, complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), including disposing off the retrieved debris outside the premises, complete all as specified and directed.

M&L for Brickwork with fly ash Bricks, straight or curved on plan exc 6m mean radius built in Cement morter 1:6, complete all as specified and directed

M&L for 18-19mm thick, prelaminated partical board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for cupboard shelves fixed with and including 2nd class hard wood supports of size as directed by the Engr-in-Charge with nails or screws as required at site, complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

M&L for 25mm thick sand cushioning including spreading and levelling etc, as in sub base of Floors etc,complete all as specified and directed.

M&L for 60mm thick interlocking pavor blocks, Factory Fabricated, Machine pressed, precast conctete reinforced with glass fibre having glossy finish, confirming to IS 15658-2006, M-35 Grade (size, shape and colour as approved by the GE) with grey cement and pigment, complete all as specified and as directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, laying of pipes, cables, etc and getting out in soft/loose soil, complete all as specified and directed.

Demolition and breaking up drain pipes 150mm bore (Salt glazed ware or AC pipes) set in cement mortar, complete all as specified and directed.

M&L for cement concrete in foundation filling and mass concrete type D2 (1:4:8) using 40 mm graded stone aggregates, complete all as specified and directed.

M&L for 150 mm bore SGSW pipe, grade 'A', laid in trenches including jointing with cement mortar, complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregates as in surface channels and drains, complete all as specified and directed

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregates for 150 mm bore pipes as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed

Removing excavated material to a distance not exc 50.00 mtr and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

Dismantling fencing posts or struts (steel or RCC), any section including taking out embedded portion by demolition of PCC block foundation and making good the disturbed ground, also including dismantling of the fencing wire/ mesh of any type and disposing off the debris outside the premises, complete all as specified and directed. Note :- For payment purpose, length of posts/struts as dismatnled shall only be considered.

Excavation in post holes and/or similar holes each not exceeding 0.50 Cum in soft/loose soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, complete all as specified and as directed.

M&L for mild steel comprising of the angle iron, flat iron etc using steel conforming to Fe-290 Gde E-165 as in posts and struts in fencing inclluding cutting tops to shape as diected, drilling holes, notching for wire etc, including necessary bolting/ riveting and embeding in concrete and similar work, complete all as specified and as directed.

M & L for Cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregates) as in PCC blocks for fixing fencing posts, foundation filling and mass concrete, complete all as specified and as directed.

S&F stainless steel, fancy type, bright finish handle of 125 mm size with screws, complete all as specified and as directed.

Supply only of chain link fencing made of mild steel galvanised wire and size of mess as per site requirement, complete all as specified and as directed.

Fixing only chain link fencing of any size including line wires, any mess, size and type, to any type of standards, rails, straining bolts etc, inclding provision of binding wire, complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) (diameter of neck 11 to 15 mm) with hexagonal or square heads at one end or screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 05 cm but n. exc 10 cm long, complete all as specified and as directed.

S&F Mild steel bars 10mm dia round bars and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Fe 290 (Gde - E-165) for holding the chain link fencing in the position etc, complete all as specified and as directed.

M&L for 2nd Class hard wood (Hollock/Kalasiris/Brijsal/Gamari) as in plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together on with glue, pinned at joints, complete all as specified and directed.

Taking down carefully existing aluminium/copper point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity) and making good the disturbed surfaces all as specified and as directed.

Taking down existing unserviceable submain wiring (including conduit /casing -caping), any size and making good the disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed.

Material and labour for point wiring for one light point or one Fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 161 above but for one switch socket outlet, 5 Amp on independent board, complete all as specified and as directed.

All as per item No 161 here-in-before but for one socket outlet 5 amps on the same board with other switches, complete all as specified and as directed

All as per item No.161 here - in - before but for one light point controlled by two, 2- way switch, complete all as specified and directed.

All as per item No 161 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Supply and fixing switch socket out let multipurpose, 3 pin, 15 amp and one 3 pin, 5 amp, controlled by one switch, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 5 amps, complete all as specified and as directed.

Supply and fixing switch socket outlet 5 pin, 5 Amp, flush type, complete all as specified and as directed.

S&F socket outlet, 5 pin, 5 Amps, flush type, complete all as specified and as directed.

S&F switch, flush type, 5 Amps, SP, two way, complete all as specified and as directed.

S&F bell push, flush type, 5 Amps, complete all as specified and directed.

S&F call bell Dingdong type, AC, 230 Volts, single pole, complete all as specified and directed.

Supply and fixing ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

Supply and fix electronic fan regulator, flush type, 5 step not less than 100 watt, complete all as specified and directed.

Supply and fixing indoor LED 18/20 watt luminaires (4 Feet Long) comprises of extruded channel in thermally conductive material, high translucent serrated milky white diffuser, make Crompton : Cat No LDL-20-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL's as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

Supply and fixing indoor LED 10 watt luminaires (2 Feet long) comprises of extruded channel in thermally conductive material, high translucent serrated milky white diffuser, make Crompton : Cat No LDL-10-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL'S as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

S&F Street Wall/Security 20W LED light luminaire, pressure die cast housing alongwith polycarbonate cover and high pressure LEDs and secondary lenses with IP66 protecton, make Crompton Cat No. LST-20-CDL-M or equivalent of make BAJAJ/PHILIPS/HAVELLS as approved by the GE, complete with and including providing connection with 3 core 1.5 Sqmm PVC insulated stranded copper conductor cable, also including providing bracket made of 25mm bore GI light grade tubing 1metre long bent to angular shape, with MS FI Clamps, nuts & bolts,painting the exposed surfaces of GI pipe and steel work with two coats of aluminium paint over 1 coat of red oxide primer after preparation of the surfaces as required , complete all as specified and directed.

Supply and fixing in repairs Bulkhead LED 10 watt luminaires, complete with all inbuilt accessories, prewired, make HAVELLS : Cat NoHEXAFT 10W LED 857 SSYM BOPC IP66 or equivalent of make BAJAJ/PHILIPS/CROMPTON as approved by the GE, including provision of twin twisted copper conductor flexible wire, complete all as specified and as directed.

Supply and fixing decorative wall mounting LED luminaries with end covers suitable for and including 1x15 watt LED lamp, Make Havells Cat No City-01 (LHDL02160099) or Equivalent Cat No. of make Bajaj/Phillips/CROMPTON as approved by the GE, including provision of copper conductor cable for connecion, complete all as specified and directed.

S&F ceiling fan, 3 star rating, ISI marked, white in colour,1200 mm sweep, 230V, SP, complete with accessories, MS hook made out of mild steel flat iron of size 25 x 5mm of the rquired length for hanging of ceiling Fan, also making connection with and including copper conductor cable from ceiling rose to fan, also including taking down of existing Fan and depositing the same in MES store yard of GE, complete all as specified and as directed, Make : Usha model TECHNIXPLUS ISI marked or Equivalent of make Havells/Bajaj as approved by the GE.

S&F exhaust fan of 250 mm sweep, 230volts, AC, PVC body, making connection with & including copper conductor cable from ceiling rose to fan, also including cutting opening in the wall/metal grills etc & making good the surfaces of wall in CM 1:3/making good the remaining metal grill etc by necessary welding etc to match with the adjoining surfaces, all as required at the site, complete all as specified and directed. Make : USHA Model No. CRISP AIR or equivalent of make CG/Havells/Bajaj/Orient as approved by the GE.

S&F ISI marked, Exhaust fan, 300 mm sweep, 230 Volts, SP, metal body, complete with and including accessories, luovers, anchoring bolts, nuts, washers, provision of PVC copper conductor cable for making connection with ceiling rose, including taking down of existing Fans & depositing the same in MES store yard, complete all as specified and as directed, Make : USHA Model No. TURBO DBB-G Grey or Equivalent of make CG/Havells/Bajaj/Orient as approved by the GE. Note : Quoted rate shall also be deemed to include for cutting opening in the wall/metal grill etc, making good the surfaces of wall in CM 1:3/making good the remaining metal grill etc by necessary welding etc to match with the adjoining surfaces, all as required at site and as directed.

S&F LED bedside light fitting (Set of 2) with 1800 swivel and in-built ON/OFF switch, make as approved by the GE, complete all as specified and as directed.

S&F Wall fan of size 400mm sweep (white), 230Volts, AC, provision of PVC copper conductor cable for making connection with ceiling rose, Make-Usha, Model No-MAX AIR SUPER WF or equivalent model of Havells/BAJAJ as approved by the GE, complete all as specified and as directed. Note :- Rate of fixing arrangement as directed shall also be deemed to be included in quoted rate.

S&F electric storage heater of 25 Litre capacity, vertical type with ABS covered outer body, 3 mm thick EPAC (Engineered Polymer Anti Corrosion) coated inner tank to suit any kind of water, interchangeable coloured (Red& green) panel, vitreous enamel coated heating element for long life, adjustable capillary thermostat for temperature regulation, multifunctional safety valve including hot & cold water CP flexible pipe etc and fixing arrangement for mounting on wall, complete all as specified and directed, Make : USHA Model No. MYSTY or equivalent of make CG/Jaquar/Bajaj as approved by the GE.

Supply and fixing sheet metal enclosure for MCBs/MCCBs DBs, Double Door, phosphatised, Powder coated , Triple Pole and Neutral (TPN), VERTICLE TYPE , 4 way, 415 Volts, IP-43 & IK-09 complete with and including 200 Amps rated bus bar, 1 Number160 Amp, 4 pole, 415 Volts incoming MCCB with rupturing capacity 25 KA, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and as directed .

Supply and fixing sheet metal enclosure for MCBs DBs, Double Door, phosphatised, Powder coated , Triple pole and Neutral (TPN), 415 Volts, 04 Ways, with and including common bus bar at incoming end, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damged surfaces to match with the adjoining surfaces, complete all as specified and as directed.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , single pole and neutral (SPN), 240 Volt , 4 Ways with and including common bus bar at incoming end, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and directed.

S & F MCB, 'C' Series, Single Pole, 240 volts, 6 to 32 Amps, ruputring breaking capacity 10KA, complete all as specified and directed.

S&F MCB 'C' Series, 4 pole, 40 to 63 Amp, 415 Volts, reputring capacity 10 KA, complete all as specified and directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size4.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 4.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 20 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed. Note for Item No 191 :- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

M & L for sub main wiring with 4 runs of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith two run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 25mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and directed. Note for Item No 192 :- For payment purposes, 4 runs of main cable (each of 1RM), 2 run of earth continuity cable (each of 1RM) and one run of conduit (each of 1RM), all together shall be considered as "1RM".

Supply and fixing in repairs single pole neutral enclosure with & including a two pin and earth plug and socket, also with and including one number single pole, MCB, 16/25 Amps 240 volts, 10 KA ruputring capacity, complete all as directed and specified.

Supply and fixing AC, three phase, Static Electronic KWH Energy Meter of accuracy class 1.0, 240V, 4 wire, 50 Hz, with Bakelite LCD Display of Rating 10-60 A with Transperent Hinged Type Box with six month History of Energy in KWH including taking down of old Energy Meter and depositing the same in MES store yard, complete all as specified and as directed.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt Sub class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed

Material and labour for galvanized iron tubing 40mm bore light grade with all fitting for protection of cable, laid in trenches/ along poles /wall/floor incl necessary clamps, bolts/nuts, complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid separately.

Taking down of existing Under Ground cable from trenches/ along wall/pole etc, complete all as specified and directed. Note :- Excavation & Earth work shall be measured & paid for separately.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 25 Sqmm 3.5core laid in trenches /along poles/on wall etc, complete all as specified and as directed Note For item No 199 : Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately.

Dismantling of existing earthing and in lieu providing new earthing complete of advance encapsulated compound based (CPRI tested) maintenance free, pipe-in-pipe technology upgraded (Zinc & Alloy coated). Zinc coated (80-100) microns with pure zinc(99.9%) & alloy coating (200-250) microns. Earthing system shall be conforming to IS-3034, the outer and inner pipe shall be 76.2mm & 41.9mm dia, 2 metre length Zinc coated with additional special alloy coating 300mm on the topside for additional protection of the terminal annular space between the pipes being filled up with compact fill (CF) (Crystalline conductive compound). The compact fill (CF) mixture shall be machine pressed in the pipes and should not disintegrate or collapse when outer pipe corrodes. The inner pipe shall be extended with terminals for connectivity. The job includes digging the pits and refilling the same by electrodite/ conductolite back fill comopound (Ground Enhancer). The BFC shall be eco friendly, it shall not contain environmentally hazard materials having ROHS certification from NABL accredited lab. The earth pit shall also be provided with earth pit cover for protection and safe guard of terminals. In area where soil condition is bad, good earth shall be provided to fill the excavated pits by mixing the same with BFC, 4 bags (as per soil condition) extra per pit/unit. The earth electrode (the main component of the earthing system) which is in direct contact with the ground shall be able to provide a means of releasing or collecting earth leakage current. The materials shall have good electrical conductivity & anti-corrosion property in wide rage of soil condition and testing on completion including dismantling unserviceable earthing complete all as specified and as directed. Make ASHLOK Model- ASEEL or equivalent of make JMV/True Power as approved by the GE.

M/S SEN CONSTRUCTION

M/S BOSE CONSTRUCTION