PROVISION OF PARKING SHED FOR AIR WARRIORS IN TECH AREA OF ASTE AND CERTAIN MAJOR REVENUE MINOR WORKS AT ASTE SDI UNDER AGE BR I AGE EM OF GEAF MARATHAHALLI BANGALORE

Amount

Demolition of cement Concrete (un reinforced) in ground floors and pavings exceeding 15 cm thickness (below or above ground level), including removal of debris outside MOD Land, complete all as specified and directed complete all as specified and as directed.

All as per item no 1 above, but , exceeding 15cm thickness including removal of debris outside MOD Land, complete all as specified and directed complete all as specified and as directed.

Excavating in post holes in soft/loose soil (or similar holes) each n.exc 0.5 cu.m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm complete all as specified and as directed .

M & L for PCC 1:3:6, type C2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M & L for MS works in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161- 1979 grade St.-240 complete all as specified and as direced.

M & L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment, confirming to Fe-410- W(Gde-E-250)quality-B complete all as specified and as direced.

M & L for MS works as in roof trusses, trussed purlins (beam,tee,angle,channel or flat sections ) including distance pieces, cleats etc confirming to Fe 410-W (Gde-E-250) quality-A complete all as specified and as direced.

S & F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as direced.

M & L for paining to new steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer, over 10 cm width by or girth not otherwise described including preparation of surfaces complete all as specified and as direced.

M&L mild steel TMT bars 10mm dia and overs, cut to length, bent to shape required, including cranking, bending spirally for rooping, columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clibs complete all as specified and as direced.

M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to timber frame work complete all as specified and as direced.

M&L for 25mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to timber frame work complete all as specified and as direced.

S & F 75mm Brass barrel tower bolts of extruded section, complete all as specified and directed.

S & F 100mm double action spring hinges, mild steel with steel wire spring, stove enamelled, black complete all as specified and as direced.

S&F 75mm extruded brass handles, cast type polished bright, complete all as specified and directed complete all as specified and as directed.

S&F Brass Locks, drawer, grade I, square type , size 50mm, 4 levers complete all as specified and as directed.

S&F for MS bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), similar small articles confirming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L for two coats of synthetic enamel paints on steel and iron surfaces n.exc 10cm width or girth after preperation of new surfaces and primary coat red oxide zinc chrome primer all as specified and as directed.

Dismantling floor, hearth or wall tilling including Cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises including removal of debris outside MOD Land, complete all as specified and as directed.

M & L for Non-skid colured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.18 Sqm but n.exc 0.38 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed in CM 1:6 complete all as specified and as directed.

All as per item no 20 above, but , as in skirting including 10mm rendering as in backing coat in CM 1:4. complete all as specified and as directed.

Cutting holes into or through reinforced cement concrete slabs, chajjas, etc. superficial area n.exc 100 Sq.cm & 15 cm depth complete all as specified and as direced.

M&L Cement concrete cast -in situ 1:2:4 Type B1 (20 mm graded aggragate) in bands, coping and the like incl weathering, throating, slightly rounded or chamfered angles or throating providedas directed including formwork complete all as specified and as direced.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., brushing neat cement slurry with 3.0kg of cement per sq.m complete all as specified and as directed.

Material and labour for 20mm thick screed bed or bedding layer in CM 1:4 for laying of tiles, complete all as specified and directed.

Material and labour for rubber moulded pre-polished chequered cement concrete tiles 20cmx20cmx25mm thick, set, jointed and pointed with white cement and pigment in floors, complete all as specified and directed.

M&L Cement concrete in surface channels and drain, cast -in situ 1:2:4 Type B1 (20 mm graded aggragate) complete all as specified and as directed.

S&F factory made branded stainless steel 3 compartment sink with each bowl of size 24 inch x 24inch x 10 inch including 850mm high stand and overhead utensil rack/shelves above the sink 6ft L x 2ft W x 2ft H with two racks, design and sample and approved by Engineer-in-Charge .

S & F CPVC 16mm bore, SDR -11 Grade for hot and cold water with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S & F bip taps 15mm chromium plated cast copper alloy with crutch or butterfly handle, screw down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 75mm bore PVC(SWR) pipes single socketed, in ay length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs PVC (SWR) 75mm bore bends any radius complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar , incl all quions, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of debris outside MOD Land, complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and as directed.

Removing excavated material exc 1.50 km but n exc. 5 km and depositing complete all as specified and as directed.

M & L for 100mm thk PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M & L for Providing precast cement concrete solid blocks masonary type -C1, 1:3:6 20mm graded aggregate exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m and upto 3.0m depth in getting out soft/loose soil all as specified and directed.

M&L for Returning , filling soft/loose soil including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified and directed.

M&L Hardcore of broken stone gauge n exc. 63 mm, deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface complete all as specified and directed.

S&F Precast septic tank made of RCC Hume pipe with 900 mm dia X 2.40 m long for 20 users capacity, in pre excavated pit, including necessary connection complete all as specified and as directed.

Material & Labour for concrete bed in PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) to drain pipes including packing under,haunching against the sides of pipes after they are laid and tested for 100 mm dia pipe complete all as specified and directed.

Material & Labour for RCC Drain pipe, class NP2, 150 mm dia , laid in trenches and jointed in CM: 1:1 and tested complete all as specified.

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour for 100mm thk cement concrete ty B1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in flooring/hardstanding and finishing cement concrete surface even and smooth etc including forming expansion joints filled with glass/bituminuous fillers etc complete all as specified and directed.

Material & Labour for Mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to Gd I IS-432 complete all as specified and as directed.

Cutting into existing manholes for connecting new drains making good to open and rendering, cutting out existing benching for and forming branch channel 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1,smooth finished and reforming benching , dia of pipe 100mm complete all as specified and as directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exc 1.5 Sqm but n exc 4 Sqm and removing to or from stores complete all as specified and as directed

Cutting opening in cement concrete walls with or without reinforcement (any descript-ion) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc. complete all as specified and directed.

M&L for precast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc 10cm in width and setting CM 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc including removal of debris outside MOD Land, complete all as specified and as directed.

M & L for rendering 10mm thick cement plaster in cm 1:6 on fair faces brick or concrete surfaces including finished even and fair, complete all as specified and directed.

M & L for rendering 15mm thick cement plaster in cm 1:4 on fair faces brick or concrete surfaces including finished even and smooth without using extra cement , complete all as specified and as directed

M & L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant painting, complete all as directed

M & L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint, complete all as directed

M&L for second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints for door and window chowkhats and other frames all as specified and directed.

Supply & Fixing 35mm thick IInd class hardwood glazed and skeliton shutters, open rebeated and prepared to receive glass, gauze, etc. divided into squares with plain chamferred or rounded, mitred and rebeated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc.; sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and directed.

S & F for 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I),kiln seasoned and chemically pressure treated complete all as specified and directed.

M & L for preparation of new wooden surfaces, painting with two coat of synthetic enamel paint over a priming coat of pink primer , complete all as specified and directed.

S&F Butt hinges extruded aluminium alloy with galvanised aluminium hinge pin anodised and fixed type B 21 of size 125mm, complete all as specified and as directed.

S & F for Aluminium anodised, barrel tower bolts 150mm long, extracted section, complete all as specified and as directed.

S & F Aluminium anodised barrel tower bolts 125 mm long, extracted section , complete all as specified and as directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified.

Cutting holes in stone walls built in cement mortar for inserting hold fasts & making good dismantled portion in CM 1:3 or cement concrete 1:2:4 type B-1, depth of embedded portion of hold fasts or lugs measured from the face of the jamb into the wall exc half brick but n.exc one brick, complete all as specified and as directed.

S&F MS hold fast and similar small articles confirming to Fe-290 Gde-E-165, complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S & F powder coated anodised alluminium frame for sliding doors, window, ventilators, partitions with one or more rebates including joining cleat for fixing and finished with metal paste on gaps of the surface in contact with stone masonry walls / brick walls complete all as specified and as directed

S & F powder coated alluminium door shutters, aluminium sections weighing 0.55 Kg/m including joining cleats glazing clips, rubber neoprene packing , handle 2 Nos and hinges 3 Nos in each door, hinges, anodised aluminium snap, mortice lock, beading screws, bearings etc. complete all as specified and as directed

S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

M&L for Provision of 5mm thick tinted black glass exc 0.5 sqm of each pane of superior quality fixed to alluminium frame works with rubber beadings complete all as specified and as directed

Supply and fix 12mm thick prelaminated particle board fixed to aluminium framework complete all as specified and as directed

S& F Aluminium Extruded section body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S & F 12mm thick prelaminated particle board prelaminated both sides with decorative choice laminations, fixed with screws to timber frame work complete all as specified and directed.

Dismantling Aluminium snap grid for false ceiling boarding, any description , fixed in any position incl hangar bars, supports, disposing off the premises, complete all as specified and directed.

S &F false ceiling grid of size 600 mm x 600 mm system using hot dipped galvanized steel section with pre coated capping, main tee of size 24 x 32 mm having 0.27mm thick at every 1200mm centre to centre, cross tee of size 24 x 27 mm having 0.25 mm thick at 600 mm centre to centre and wall angle of size 19 x 19 mm having 0.35 mm thick fixed to the periphery of the wall, and suspended at every 1200 mm centre to centre in both direction using 2.00 mm thick GI wire and fixing 600 x 600 mm x 14 mm mineral fibre regular edge ceiling tiles complete all as specified and directed. Make : Amstrong or any equivalent confirming to IS.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in openings as per specification and drawing, complete as specified and directed

Supply and fix factory made Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design, with particle board core with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing suppling and fixing in the frame at site as per specification and drawing, complete as specified and directed

S & F 100 mm butt hinges medium weight cold rolled mild steel fixed with screws or welded, complete as specified and directed

S & F Aluminium alloy anodised sliding door bolt with hasp staple ( bolt type) and fixing clip of sheet, cast or extruded sections not less than 12 mm dia with and incl minimum of 6 bolts and nuts four on bolt plate and two on staples 250 mm long, complete as specified and directed

Supply and fix 100mm aluminium handles, cast type, anodised, complete as specified and directed

M&L for RCC 1:2:4 Type B1 (20mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like , complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), fair finished surface, complete all as specified and directed.

Material and labour for non skid coloured ceramic tiles 7 to 8mm thick (Square/ rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

Material and labour for glazed coloured ceramic tiles in vertical surfaces 350mm x 250mm x 7mm / 450x350x7mm thick in dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match incl backing coat of 10mm thick CM 1:4, complete all as specified and directed.

S& F in repairs , Vitreous china urinals, half stall type, complete incl providing and fixing clubs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass srews, pointing around urinal back in cement; fixing flush pipe , grating and union for discharge pipe, complete all as specified and directed.

S&F in repairs, vitreous china wash basin, white, flat back, size 630 x 450mm, excl taps, chain and plug and porcelain stopper including CP waste coupling of 32 mm (half or full threaded), brackets, complete all as specified and directed.

S & F in repairs 15mm bore Pillar taps, cast copper heads, capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm , complete all as specified and directed.

S&F in repairs PVC (SWR) 75 mm bore floor trap, plain with grating incl jointing with solvent cement complete all as specified and directed.

M & L for tubular towel rail, 20 mm dia, ' D' type, 60 cm long between flanges, brass chromium plated, fixed in repairs, in rapairs complete all as specified and directed.

S & F in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms), complete all as specified and directed.

Taking up or down steel tubing and connections, 15mm bore complete all as specified and as directed.

S & F CPVC 16mm bore, SDR -11 Grade for hot and cold water with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M & L for rendering 10mm thick cement plaster in cm 1:6 on fair faces brick or concrete surfaces including finished even and fair, complete all as specified and directed.

M&L for moorum/red bajri filling in floors or paving, laid in layers n.exc 15 cm thk, spread,levelled and rammed including watering complete all as specified and directed.

S & F in repairs LDPE pipes 32 mm dia for WHB or sink, pressure rating 6 kgf/cm2 fixed complete to walls, ceilings, or in floors etc, complete all as specified and directed.

M&L for point wiring with 1.5 sqmm nominal cross sectional area, single core, 1100 volts grade, stranded, PVC insulated , unsheathed copper conductor cable in and including PVC casing capping complete with and including all accessories/fittings, brass screws, washers etc, sunk zinc cozted pressed steel terminal boxes including two coats of whie/colour washing/distempering etc to the distrubed surfaces to match the existing with 3 mm thick plastic laminated sheet top cover concealed in wall with and including continuos earth wire of size 1.5 sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for One fan point controlled bu one, one way switch

All as per item no 99 above ,but, one fan point controlled by one way switch complete all as specified and directed.

All as per item no 99 above ,but, for one 3 pin, 05-06 Amps socket outlet point on same board controlled by one way 05/06 Amps switch complete all as specified and directed.

All as per item no 99 above ,but, for one 3 pin,05/06 Amps socket outlet point on independent board controlled by one way 05/06 Amps switch complete all as specified and directed.

All as per item no 99 above ,but, for one 3/5 pin , 15/16 Amps socket outlet point on independent board with 2.5 sqmm cables complete all as specified and directed.

S&F switch piano flush type, 05/06 Amps single pole, one way 240 volts in replacement of old u/s complete all as specified and directed.

S&F ceiling roses surface type PVC/Polycarbonate , isolated body with three terminals complete all as specified and as directed.

M&L for making circular opening by cutting brick wall 40cmx40cm thickness 23cm complete with inserting hume pipe collar of internal dia 300mm & length 23cm and filling all around (between wall and outer dia of hume pipe collar) with PCC (1:2:4) B0, 12.5mm graded aggregate and grouting 04 nos bolts of size not less than 10mm dia and 100mm long with nut & washer and making good to disturbed surface (note:- Necessary support in high rise building (ground floor to third floor) for working from out side shall be deemed inclusive) complete all as specified and as directed.

S&F exhaust fan 300mm sweep, metallic body (Heavy Duty), single phase, 900rpm, including fixing arrangement with suitable lovers complete all as specified and as directed. Make : Havells (Turbo force) or equivalent in Crompton & Greaves / Bajaj

Supply and fixing stationary storage type (Vertical type) energy efficient (5 star rated) electric water geyser of capacity 25 ltrs including fixing with necessary anchor bolts etc complete all as specified and as directed. Make: Havells Product Code GHWAPFTWH025 ( Vertical) complete all as specified and directed.

Supply and fixing stationary storage type (Horizontal) energy efficient (5 star rated) electric water geyser of capacity 25 ltrs including fixing with necessary anchor bolts etc complete all as specified and as directed. Make : Havells Product Code GHWCAMTWH025 ( Horizontal) complete all as specified and directed.

Supply and fix GI pipe medium grade of size 15mm dia with all fittings and connections, laid in floors or trenches/fixed on walls/ceilings and testing including making holes/chasis in walls and making good complete all as specified and directed.

Material and labour for cutting & screwing existing steel tubing of size 15 mm bore for alteration or additions (or lengthening screw on pipe to form connector) done in position without taking down complete all as specified and as directed.

Supply and fix PVC connection up to 450 mm in length suitable to connect GI pipe 15 mm dia to cold water inlet of geyser cpmplete all as specified and as directed.

Supply and fix PVC connection up to 600 mm in length suitable to connect GI pipe 15 mm dia to hot water outlet of geyser complete all as specified and as directed.

Supply and fix 15 mm bore Stop valves, chrominum plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union fixed all as specified and directed by Engr-in-charge.

Supply and fix 15 mm bore bib tap,cast copper alloy,chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified .

Material and labour for sub main wiring in pvc conduit with 2 run of 4.0 sqmm single core multistranded pvc insulated cable unsheathed 1100 volts grade with one run of earth wire of 2.5 sqmm copper earth continuity conductor cable connected to common earh and earth dolly complete and including pvc conduit all as specified and as directed .

S & F in replacament single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB 20 Amps capacity complete all as specified and directed .

Supply & fix exhaust fans Turbo force SP 900 RPM.AC single phase 230/ 240 V of size 300 mm sweep with louver etc all as specified and directed . Make : Havells (Turbo force) or equivalent in Crompton & Greaves / Bajaj

Material and Labour for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non metallic rigid medium grade PVC conduit with all accessories alongwith fixing arrangements in walls , roofs , floors etc., or fixed in walls and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor connected to common earth dolly in the existing steel terminal boxes all as specified and as directed for One Exhaust fan point controlled by one switch.

Cutting holes into or through cement concrete slabs,chajjas, etc. reinforced or otherwise if reinforcement is cut through all as specified and as directed.

Supply and fix Wall mounted fan 400 mm sweep 3 blades white colour with speed controller rope 1350 RPM . Make : Havells (Sameera) or equivalent make.

Supply , install and testing complete new digital water level indicator device operating on single phase supply direct display in 6'' size (letter display) digital system in meter / centimeter of water level of over head tank ensuring alaram while water fall or rise over pre-determined limit with the following description complete all as specified and directied by Engr-in-charge. (a) The entire unit must operate through a compact electronic citcuit which must reliable operation at 230 volts + 10% at 50 Hz with reliable in display and alaram at low and high level of over head tank. (b) One circuit must be housed in high impact polystryrene moulded box with nylon moulded connection strips.The level system must resistance transducer. (c) The whole unit system electronically control and the upper level and lower level indication must be in two part Each complete part must be fitted in MS CRCA sheet box separately.One must be installed multi core copper conductor and second at pump house with locking arrangement. Note: Pvc insulated multi core copper conductor cable 0.5 sqmm from water level indicator to over head tank,Sensor shall be connected with pvc insulated copper conductor cable so as to indicate the water level empty,25% ,50%,75%, & 100% tank full.

Supply & fixing of timer switch in accordance with IEC 60730-1 and 60730-2-7 Manual switching on/automatic/Off option & Hourly/daily/weekly switching dial with captive segments including clock provision +/- 5 mins for the daily time switch - 10 0c to + 55 0c operatinf temperature Make: Cat part no. 412828 of Legrand or equivalent in Indoasian/Havells etc

Boring of holes under road, pavement, hard standing 1.5 to 2 mtrs below ground level by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 40 mm dia suitable for 0.4 mpa working pressure for passing of UG cable complete all as specified and directed.

Supply, laying and testing of 10 sqmm 2 core LT UG cable XLPE insulated screened PVC bedded, galvanised steel strip wounded ,electric power cable (heavy duty) 1100 volts with stranded aluminium conductor and making connection with suitable lugs complete all as specified and directed. Note: Rate quoted are deemed to be included for laying,clamping with non mettallic PVC conduit of 25 mm dia and its accessories and making good to the disturbed surface of wall/floor etc complete all as specified and directed.

M&L for making circular opening by cutting brick wall 40cmx40cm thickness 23cm complete with inserting hume pipe collar of internal dia 300mm & length 23cm and filling all around (between wall and outer dia of hume pipe collar) with PCC (1:2:4) B0 , 12.5mm graded aggregate and grouting 04 nos bolts of size not less than 10mm dia and 100 mm long with nut & washer and making good to distrubed surface (note:- Necessary support in high rise building (ground floor to third floor ) for working from outside shall be deemed inclusive) complete all as specified and directed.

S&F of socket outlet 3 pin, 05/06 Amps (2in1 multipurpose) flush type 240 volts in replacement of old u/s complete all as specified and as directed

S&F of socket outlet 3 pin, 15/16 Amps (2in1 multipurpose) flush type 240 volts in replacement of old u/s complete all as specified and as directed

S&F of switch piano flush type, 15/16 Amps single pole, one way 240 volts in replacement of old unserviceable complete all as specified and as directed

S&F electronic fan regulator stepped , socket type 400w including removing the switch board panel and making the provision for fixing the electronic type regulator and refixing the same complete all as specified and as directed

S&F lumiline LED tube with patti, 2 feet, 10 watts alongwith tube complete all as specified and as directed. Make : Bajaj cat no : BCLSB 10 WH or equivalent in CG/PHILIPS

S&F lumiline LED tube with patti, 4 feet, 18 watts alongwith tube complete all as specified and as directed. Make : Bajaj cat no : BCLSB 18 WH or equivalent in CG/PHILIPS

S&F ceiling fan 1400mm sweep, 5 star rated energy efficient type, white colour with down rod, rubber reel, nut bolt, washers, clamps, canopys, connecting up using suitable size copper conductor flexible twisted cable from existing ceiling rose to fan connector etc, but, with out regulator and testing including making a fixing arrangement of ceiling fan on roof complete all as specified and as directed. Make: Havells , Cat Part No : ES-50/Bajaj/Crompton

Testing and submitting of soil resistivity test report as per "Wenne four electrode method" (IS 3043) and Submit the design calculation of earth electrode resistance , earth strip resistance, earth grid resistance as per IS 3043 and also submit the description of material to be incorporated all as specified and as directed. (a) Ensuring grid resistance to be less than 1 ohm. (b) Ensuring the size of conductor for bearing the fault current. Note : (i)Testing shall be done for a spacing of 0.5 to 10 mtrs depend on space availability. (ii) Minimum 6 readings required in each direction. (iii) The measurement shall be carried in 4 directions at each.locations depends on space availability.

ADWITHI

G K CONSTRUCTIONS

RASHMI BUILDERS