Internal Development work of 4/6/10 Percent Abadi plots in Village Ajayabpur, Greater Noida.

Road Work:- Cleaning jungle including up rooting of rank, vegetations grass, push, wood trees and samplings of grith upto 30cms. measured at a height of 1 M. above ground level and removal of rubbish up to a distance of 50M. Out side periphery of area cleared. (SOR-20/259(i))

Same as above 259(i) above but grass only (SOR-20/259(a)

Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads. Transporting to site, spreading, grading to required slope and compacts to meet requirement of Table No 300-2: lead upto of 5.00KM (MORTH--20/305/3.16)

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). (DSR-18/16.2)

Supplying and stacking at site. (DSR-18/16.3)

90mm to 45 mm size stone aggregate (DSR-18/16.3.1)

63mm to 45 mm size stone aggregate (DSR-18/16.3.2)

53mm to 22.40 mm size stone aggregate (DSR-18/16.3.3)

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . (DSR-18/16.4)

Supplying and stacking at site.: Moorum. (DSR-18/16.3.10)

Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-18/16.7.1)

Providing and applying tack coat with bitumen grade of VG-10 using pressure distributor at the rate of 0.50 Kg per sqm on the prepared bituminous surface cleaned with mechanical broom. (MORTH 5.02/503)

Providing and laying Bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @5.40 Percent of mix and filler transporting the hot mix to work site, laying with hydrostatic paver finisher with sensor control to the required grade, level, and alignment rolling with smooth, wheeled vibratory and tandem rollers to achive the desired compaction as per MORTH specification clause No 507 complete in all respects. (MORTH/5.05/507(B))

30mm compacted thickness with bitumen penetration of [email protected]% by weight of total mix. (MORTH-5.05/507(B))

Excavation in foundation in ordinary soil (Loam clay or sand) including lift upto 1.50 M and lead upto 30.00M and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer incharge upto a distance of 30m from the foundation trenches (where machine con not reach/move) (SOR/251 (A)/4.1.1)

Supply of ISI marked RCC S&S NP-3 pipes of following size including carting, loading, unloading at godown including all taxes and levies & rubber rings, (AR/GNIDA)

250mm dia NP-3 pipe AR

Laying of NP-3 RCC S&S pipes jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 coarse sand) including testing of joints etc. complete. (AR/GNIDA)

250mm dia NP-3 class

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : (DSR-18/18.33)

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (DSR-18/18.33.1)

Drain Work:- Cement concrete with 4cm gauge Approved stone ballast coarse sand & cement in the proportion of 8:4:1 including supply of all materials labour tools & Plants etc required for proper completion of the work

8:4:1 (1 Cement 4: Coarse sand :8 graded stone aggregate 40mm nominal size) (SOR-20/281/5.08)

Plain/Reinforced Cement concrete in open foundation complete as per Drawing and Technical Specifications. (MORTH-20/9.06/E/Case-II)

RCC Grade M-25 using batching plant transit mixture and manual placing (MORTH-20/9.06/E/Case-II)

Steel reinforcement for RCC work including straightening cutting bending placing in position and binding all complete upto plinth level

Thermo Mechanically treated bars of grade Fe-500D or more. (SAIL Steel) (DSR-18/5.22.6/AR)

Sewerage work:- Excavation in foundation in ordinary soil (Loam clay or sand) including lift upto 1.50 M and lead upto 30.00M and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer incharge upto a distance of 30m from the foundation trenches (where machine con not reach/move) (SOR/251 (A)/4.1.1)

Depth from 0.0 to 1.5M below G.L.

Supply of ISI marked RCC S&S NP-2 pipes of following size including carting, loading, unloading at godown including all taxes and levies & rubber rings, (AR/GNIDA)

250mm dia NP-2 pipe AR

Laying of ISI marked RCC NP-2 pipes of following size including carting, loading, unloading, at godown, including all taxes and levies & rubeer rings of following dia

250mm dia (AR/GNIDA)

Supply of ISI marked RCC S&S NP-3 pipes of following size including carting, loading, unloading at godown including all taxes and levies & rubber rings, (AR/GNIDA)

250mm dia NP-3 pipe AR

Laying of ISI marked RCC NP-3 pipes of following size including carting, loading, unloading, at godown, including all taxes and levies & rubeer rings of following dia

250mm dia (AR/GNIDA)

Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) in concrete cradle under NP-2 pipe of following diameter including centring shuttering but excluding excavation as per approved. (GNIDA/AR)

250mm dia NP-2 pipe (DSR-18/AR)

Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) in concrete cradle under NP-3 pipe of following diameter including centring shuttering but excluding excavation as per approved. (GNIDA/AR)

250mm dia NP-3 pipe (DSR-18/AR)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. NP-2 pipe (DSR-18/19.6.3/AR)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. NP-2 pipe (DSR-18/19.6.2/AR)

Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) in concrete cradle under NP-2 pipe of following diameter including centring shuttering but excluding excavation as per approved. (GNIDA/AR)

150mm dia NP-2 pipe (DSR-18/AR)

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : (DSR-18/19.9)

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : (DSR-18/19.9.1)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-18/19.9.1.1)

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-18/19.10.1)

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : (DSR-18/19.11)

1.68 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : (DSR-18/19.11.1)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-18/19.11.1.1)

Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m : (DSR-18/19.12)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-18/19.12.1)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. (DSR-18/19.16)

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : (DSR-18/18.33)

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (DSR-18/18.33.1)

Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement mortar 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (DSR-18/19.34)

150 mm dia (DSR-18/19.34.2)

M-150 brick work in 1:6 cement & fine sand 1.25 FM mortar in foundation and plinth including supply of all material labour and T&P etc required for proper completion of the work. (SOR-20/303) same as item no 303 but in 1:4 one cement & four fine sand of 1.25 F.M. mortar. (SOR-20/305) Same as item no 305 but in 1:4 one cement & four coarse sand of 2.20 F.M. mortar. (SOR-20/305(A))

Water Supply work:- Excavation in foundation in ordinary soil (Loam clay or sand) including lift upto 1.50 M and lead upto 30.00M and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer incharge upto a distance of 30m from the foundation trenches (where machine con not reach/move) (SOR/251 (A)/4.1.1)

Depth from 0.0 to 1.5M below G.L.

Providing & laying jointing & testing of folowing dia rigid PVC pipe of 6kg/cm2 working presser (finolex or equivalent make rigid PVC pipes as per IS 4485:2000) including all fitting & specials jointing material etc. for proper completion of the work.

90mm dia (O.D)

110mm dia (O.D)

Providing and fixing G.I. pipes complete with G.I. fittings includingtrenching and refilling etc. External work (DSR-18/18.12)

15 mm dia nominal bore (DSR-18/18.12.1)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : (DSR-18/18.46)

15 mm nominal bore (DSR-18/18.46.1)

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :

15 mm nominal bore (DSR-18/18.20.1/AR)

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : (DSR-18/18.59)

80 mm dia (DSR-18/18.59.2)

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : (DSR-18/18.31)

100 mm diameter: Class I (DSR-18/18.31.1.1)

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : (DSR-18/18.33)

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (DSR-18/18.33.1)

Labour cess and GST will be paid extra as per Govt. orders.