ADDN/ ALTN AND IMPROVEMENT TO CERTAIN JOINERY AND ASSOCIATED WORKS IN 14 AFH APPROACH PATH SMQ AT AFA HYDERABAD

Amount

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P.brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for type of shutters(hung/sliding) of doors, windows, ventilators, including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections / appropriate Z sections and other sections of aproved make conforming to IS- 733 and IS- 1285, with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, CP brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F Powder coated (Thickness not less than 50micron) Aluminium anodised Grill, aperture n exc 75 mm ,size 6mm x 4mm thick, including 1 mm thick channel fixed with steel screws complete all as specified and directed.

S&F 12mm thick toughened stained glass door with one see through line in centre, of approx size 1.20m x 2.10m (single leaf) with approved design/ Air force logo not less than 0.30 Sqm on each leaf, white on white deep acid etching and including fixed with following fittings a)Door set L-321 top pivot -01Nos, b) Door set lock L-325-01Nos, c) Door set floor spring FS-120 - 01Nos, d) Glass Handle of 300mm size-02Nos (It includes all necessary hardware’s required for functioning) complete for each door, all as specified and directed by Engr In Charge.

S&F Aluminium(extruded section body) door closer hydraulically regulated designation No. 3, universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61to 80 Kg all as specified. MAKE : Godrej or Equivalent.

S&F double action floor door spring hydraulically regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box main body of stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed for aluminium door all as specified.

S&F of brass 4 Levers Mortice lock, vertical type, size 100mm

S&F 12 mm thick prelaminated particle board exterior grade laminated on both side with decorative choice lamination fixed to aluminium frame work for door panel shutter complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified.

M&L for Granite 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills/jams, cooking platforms and like over 15 mm thick cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters) from the frame exc 1.5 sq. m but n exc 4 sq. m complete all as specified and as directed

Taking down Chowkhats or frames with shutters (wihout taking off shutters) from the frame n.exc 1.5 sq. m complete all as specified and as directed

Dismantling boarding/partition of any description, fixed in any position fixed with nails

Taking down cement plaster in wall/ceiling surfaces on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry of type C1 1:3:6 (using 20mm graded stone aggregate) with solid blocks exc 10cm in width and setting in cement mortar 1:4 etc complete all as specified and as directed.

M&L for plastering in internal wall surfaces of 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed by Engr -in- charge.

M&L for plastering in external wall surfaces of 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) with water proofing compound complete all as specified and directed by Engr -in- charge.

M & L for two coats of oil bound distemper on newly plastered surface of walls over a coat of alkali resistant primer including preparation of surfaces complete all as specified and directed by Engr -in- charge.

M&L for preparation of newly plastered surfaces of external walls and applying two coats cement base paint over a coat of cement primer complete all as specified and directed by the Engineer-in-Charge.

Supply only Liquid water proofing compound.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out soft / loose soil, complete all as specified and as directed.

M&L for hardcore of gauge n exc. 63 mm of broken stone boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M&L 100 mm thick PCC (1:4:8) type D2 (40 mm graded aggregate) as in sub base for floors all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in ground floors and pavings n exc 15 cm thickness (below or above ground level) any position and disposed off to a distance of 5km from the starting point and deposited where directed etc complete all as specified and as directed.

M&L PCC (1:1/2:3) type B2 (20 mm graded aggregate) finishing cement concrete surface even and smooth Without using extra cement as in floors all as specified and as directed.

M&L for forming 12mm thick Expansion joints for 100mm thick concrete slab, filled with pre-formed bituminous filler and top 30 mm primed and sealed with sealing compound, Grade 'B'.

M&L for forming Construction joints 30 mm deep x 10 mm wide, filled with sealing compound Grade B.

M&L for forming Dummy joints 50 mm deep x 10 mm wide, filled with sealing compound Grade B.

M&L 75 mm thick PCC (1:4:8) type D2 (40 mm graded aggregate) as in sub base for floors all as specified and as directed.

M/L for Sand filling of 50mm thick under pavers, floors or in foundation including watering and consolidation, etc compelete all as specified.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, etc complete all as specified and as directed.

M&L PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in copings, kerbs and similar works etc complete all as specified and as directed.

Vipin Kumar and Brother (BID ID -3137014)

GUTHIKONDA BROTHERS (BID ID -3137995)

S J REDDY (BID ID -3138614)

M/s RAMA LAKSHMI CONSTRUCTIONS (BID ID -3144887)