SPECIAL REPAIR TO AIRMEN/NCs(E) ACCN AT AF STN NAL

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement Concrete (unreinforced) of any description and in any position including any type of rooftreatment , PCC padding, brick tiles, lime concrete etc, complete all as specified and directed. Note: All demolished material / debries will be taken by the contractor out side the Airforce station Nal with out any extra cost.

Material and labour 25mm thick PCC 1:2:4, type B-0 (using 12.5mm graded aggregate) as in sub base of floor surface finished even & fair complete all as specified and directed.

Material and labour non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.06sqm but n.exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, over and including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material and labour non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11sqm but n.exc 0.18 sqm. in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 7.00 but coloured joint free ceramic tiles matt finish, as in vertical surface such as in skirtings over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour Coloured Glazed Ceramic tiles (Digital Designer tiles) 350x 250x 7mm / 450X 350X 7mm and 6 to 7mm thick on vertical surfaces such as skirting, dados and risers to steps etc over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour 20 to 25mm thick Granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge. Note - Roughening of the bottom surface i. e. opposite side of exposed surface of granite slab by means of application of araldite and spreading of sand shall be included in quoted rates

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Material and labour 75mm thick PCC 1:3:6, type C2 using 40mm graded stone aggregate as in floors, plinth protection and including filling the joints with bitumen complete all as specified & directed. Note:- The plinth protection shall be laid in panels and length of the each panel shall not be more than 2.00 mtr all as directed. joint shall be 6mm wide and filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided and cost thereof shall be deemed included in unit rate.

Material and labour Cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops, on junction of parapet, coping etc cement concrete surface finished even and smooth without using extra cement complete all as spd and directed.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and including brushing neat cement slurry with 3 Kg/Sqm in roofs complete all as specified and directed.

Material and labour Cement concrete 1:3:6, type C-1(using 20 mm graded stone aggregate) as in roof paddding, mass concrete finishing as required gradient cement concrete surface even and smooth without using extra cement complete all as spd and directed.

Material and labour 15mm thick screed bedding in cement mortar 1:4 mixed with water proofing compound pidiproof LW+ @ 200ml per 50Kg cement as per manufacturers instructions on concrete surface of roof and finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge (WPC shall be measured and paid separately)

Material and labour grit finish APP based polymeric membrane minium weight 3 Kg/Sqm and minium 3 mm thick, reinforced with polyster non wove fabric (wt. not less than 150 gms/Sqm ) laid by torch forced application over a coat of bitumen 85/25 grade applied hot @ 1.20 Kg/Sqm laid over and including a priming coat using bituminious primer @ 0.40litre/ sqm, with minimum 75mm side overlaps and minimum 100mm end overlaps etc complete all as specied and direct.

Material and labour Cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors over and including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Supply and fix 20 mm boreTubes, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Fixing only 20 mm bore tubes, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fix 15 mm bore tubes, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors for concealed pipe line, including cutting holes or grooves in brick wall/rcc and making good with cement mortar 1:3, complete all as specified and as directed.

Fixing only Tubes, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 15 mm bore complete all as specified and as directed.

Dismantiling water tanks from position and setting a side for cleaning and removing all scale and dirt from tank emptying, drying, cleaning by scrubbing the dust with wire brush from tank by removing inlet and outlet pipe and hosting, reconnecting and refixing in position 500 ltrs capacity complete all as specified and as directed..

Dismantling water tanks any type of capacity Exc 250 but n.exc 500 liters complete all as specified and as directed.

Supply and fix Rotational moulded polyethylene water storage tanks of white colour triple layered (ISO certified) (cylindrical vertical with closed top ) hoisted and fixed in position all as specified in Sch “A” of capacity 500 liter, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed.

Supply and fix in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Supply and fix in repairs 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed.

Supply and fix Sink with drainage board made by stainless steel 1 mm thick kitchen or laboratory with plugs, washers & CP waste fittings etc complete including bedding in cement mortar to dwarf wall or including fixing cantilever brackets connecting union to pipe overall size 915 mm X 460 mm and bowl size 410 mm X 330 mmX 160 mm complete all as specified and as directed.

Supply and fix in repairs stainless steel plate rack made out of stainless steel 1 mm thick sheet of size 31" x 36" complete all as specified and as directed.

Supply and fix in repairs PVC valveless syphonic action type flushing cistern 10 ltr capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and as directed.

Supply and fix in repair wash hand basin Vitreous china white flat back size 550x400mm excluding taps, waste, chain and plug and porcelain stopper and including brackets complete all as specified and as directed.

Supply and fix PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

Supply & Fixing 15 mm dia Pillar taps fancy type chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. Make: Prayag, Jaquar, Marc

Supply and fix in repair 15 mm bore brass Bib taps (long shank with flange) cast copper alloy fancy type chromium plated with crutch or butterfly handle , screwed down, screwed for iron pipe or for brass ferrule fixed in repiar complete all as specified and directed. Make: Prayag, Jaquar, Marc

Supply and fix in repair 15 mm dia Stop valves/ angle cock cast copper alloy fancy type chromium plated with long shank and cup with crutch or butterfly handle , screwed down, screwed for iron pipe or for brass ferrule fixed complete all as specified and directed. Make: Prayag, Jaquar, Marc

Supply and fix in repiar 15 mm dia Stop valves cast copper alloy fancy type chromium plated with long shank and cup (concealed type) with crutch or butterfly handle , screwed down, screwed for iron pipe or for brass ferrule fixed complete all as specified and directed. Make: Prayag, Jaquar, Marc

Supply and fix in repairs 125mm dia brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union fixed complete all as specified and directed. Make: Prayag, Jaquar, Marc.

Supply and fix in repair towel rail 20mm dia chromium plated including 600mm long including brackets, screws and wooden/plastic cleats complete all as specified and directed.

Supply and fixed in repair vitreous china wash down water closet pan semi pedestal pattern (Anglo Indian type white including PVC seat cover, connection to waste pipe and flushing pipe complete all as specified and directed. Make - Hindustan/Cera/Neycer

Supply and fix PVC floor / nahani trap 75mm dia fixed in position complete all as specified and directed.

Taking down chowkats or frames n exc 1.5 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed.

Taking down shutters of any description n exc 1 sqm and removing to store complete all as specified and directed.

Taking down shutters of any description exc 1.00 sqm but n exc 2 sqm and removing to store complete all as specified and directed.

Material and labour for preparation of old painted surface of wood and applying two coats to synthetic enamel paint exc 10cm width/girth complete all as specified and directed.

Supply and fix 100 mm long, medium weight cold rolled mild steel Butt hinges and fixed complete all as specified and directed. Note: welding of MS hinge to be done in case of Mild steel frames or in case of PVC/wooden frames screwing shall be included in the quoted rates.

Supply and fix 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 150mm extruded aluminium alloy handles fabricated type anodized complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Supply and fix Pressed Steel door frames size 105x60mm for doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

Supply and fix Pressed Steel door frames size 125x60mm for doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

Supply and fix factory made solid UV wood grain printed panelled / plain PVC single piece door shutter 30mm thick style, consisting of frame made out of MS tube 19 guage thickness and size of 25mmx25mm for sitles, top and bottom rails MS frame shall have a coat ofsteel primes. The frame shall be covered with heat moulded woood grain UV printed PVC sheet tape fixed in MS frame welding sealed to the styles and rail with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed by Engineer-in-Charge, manufacture specification as per drawing Make : M/s HR Enterprises Pathankot, Door Craft Industry, Delhi, M/s Trehan Doors Pathankot. Note: The shutter is to be fixed with 50mm size self drilling star screws full threaded.

Supply and fix 34/35mm thick factory made single piece wire gauge door / shutter solid PVC UV printed doors - Wood Free consisting of 5mm thick solid PVC sheet on both side (both side mulit colour UV printed) using steel / aluminium XPM/ wire mesh and consisting frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 19mm x19mm for the top, bottom and lock rails with PVC beading in all around. M. S. frame shall have a coat of metal primers. MS Frame shall be covered with heat moulded (Rigid) 20/22mm PVC solid sheet at styles, top rail and bottom rail (Rigid) MS Frame welding sealed to the style and rail with sutiable PVC Sheet beading and joined together with solvent complete as per direction of Engineer-in-charge and as per manufacturer’s specification and drawing Make : M/s HR Enterprises Pathankot, Door Craft Industry, Delhi, M/s Trehan Doors Pathankot. Note: The shutter is to be fixed with 50mm size self drilling star screws full threaded.

Supply and fix factory made solid UV PVC door frames of size 90mm x 55mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, etc complete all as specified and as directed. Make HR enterprise/ Alstone Make : M/s HR Enterprises Pathankot, Door Craft Industry, Delhi, M/s Trehan Doors Pathankot. Note: The shutter is to be fixed with 50mm size self drilling star screws full threaded.

Supply and fix factory made flush shutters solid core construction,with particle BWP board core 30mm thick and plywood face panels,commercial type on both side ISI mark incl taking down old shutter complete all as specified and directed.

Supply and fix factory made flush shutters solid core construction,with particle BWP board core 25mm thick and plywood face panels,commercial type on both side ISI mark incl taking down old shutter complete all as specified and directed.

Taking down wooden door shutters of any description and size and refixing after easing and replacing the fittings as required (Note all fittings shall be measured seperately under respective items) complete all as specified and directed.

Material and labour for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer over exc10cm width or girth complete all as specified and directed.

Supply and fix Factory made Box type Steel window 1.25mm thick (primer coated) ERW hollow section of size 60mmx25mm including grill using 10sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mm x 25mm and 1.25mm thick including cutting holes and good dismantled portion in PCC(1:2:4) type B1 four Nos for each window/ ventilator including following fitting welded to frame shutter : (a) Hold fast,150mm long of 12mmx3mm made to shape 04 Nos per ventilator. (b) Handle of Z Sec 20mmx25mm, 100mm long-per leaf. (c) MS Tower bolt 150mm long-02 No per leaf. (d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) Cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf. (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf. (g) Stainless steel wire mesh 0.36 mm nominl dia and average width of aperture1.40mm. (h) 3mm thick sheet glass ordinary quality with oil putty. Note : (i) TD of Chief Engineerls Chandigarh Zone, TD-219 i.e Typical deta of Box window (Steel) with Fly proof Shutter for any missed out details if any. (ii) The mode of measurement shall only be one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account. (iii) MS Grill, glass and wire mesh shall be included in the unit quoted rate. (iv) Rate quoted shall include shop coat of red oxide primer for full window including grill.

All as per srl item No.62.00 here in before but as in ventilators complete all as specified and directed.

Material and labour for preperation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer width or girth exc 10cm complete all as specified and directed.

Material and labour for two coats of synthetic enamel paint on new steel sufaces width or girth exc 10cm incl preparation of surfaces complete all as specified and directed.

Material and labour for preparation of new steel surfaces and applying two coats of synthetic enamel paint over one coat of redoxide primer width or girth n.exc 10cm complete all as specified and as directed.

Material and labour for prepartion of old steel surfaces and applying two coats of synthetic enamel paint width or girth exc 10cm complete all as specfied and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specfied and as directed.

Supply and fix Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.40 mm & fixed with tinned takcs,cut nails, galvanised wire staples or with woooden beading complete all as specified and as directed.

Supply and fix in repairs Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.40 mm & fixed with tinned takcs,cut nails, galvanised wire staples or with woooden beading complete all as specified and as directed.

Supply and fix in repairs heavy duty Stainless steel (Grade 305) curtain rods 20 to 25mm dia complete all as specified and as directed.

Supply and fix in repairs Stainless steel (Grade 305) brackets with finnals (open ends) suitable for curtain rods of 20 to 25mm dia complete all as specified and as directed.

Supply and fix in repairs Stainless steel (Grade 305) brackets (Dead ends) suitable for curtain rods of 20 to 25mm dia complete all as specified and as directed.

Supply and fix MS Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk water tanks and similar work including all necessary drilling or cutting holes in brick/ concrete surfaces and making good, welding work, bolting or reveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fix for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing as directed, drilling holes, notching for wire, etc.; flat iron fillets including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fix for Pre-painted galvalume aluminum zinc coating GI based corrugated or semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ chajja /cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed. Note: Galvalume Sheet shall be curved profile suitable for chajja and rate quoted shall be included in the same.

Material and labour for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove and making good with cement mortar 1:3, complete all as specified and directed.

Material and labour for green Marble slab work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. Note - Roughening of the bottom surface i. e. opposite side of exposed surface granite slab by means of application of araldite and spreading of sand shall be included in quoted rates

Material and labour for green Marble slab work 18 to 20mm thick (table rubbed and polished) in vertical risers and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. Note - Roughening of the bottom surface i. e. opposite side of exposed surface granite slab by means of application of araldite and spreading of sand shall be included in quoted rates.

Material and labour Providing and injecting chemical emulsion for post construction anti termite treatment using chemeical chloropyrihos 20% EC emulsifiable concentrate of soil under existing floors using chemical emulsion @ 1 liter per hole 300 mm apart and plugging holes with cement mortar 1:2 to match with the existing surface complete all as specified and directed.

Material and labour Providing and injecting emulsion for post construction anti termite treatment using chemeical chloropyrihos 20% EC emulsifiable concentrate along the external wall of building below conctee or masonry apron using chemical emulsion @ 2.25 liter per linear etre including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 in apron complete all as specified and directed.

Material and labour Providing and injecting emulsion for post construction anti termite treatment at points of contract of wood work by using chemeical chloropyrihos 20% EC emulsion in oil or kerosene based solution @ 0.5 liter per hole by drilling 6mm dia holes by degree @ 150 mm centre to centre and sealing the same and making good the disturbed surfaces to match with the existing surface complete all as specified and directed.

Demolition of reinforement cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

Material and labour reinforced cement concrete M 25 Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like etc complete all as specified and directed.

Supply and fix Mild steel TMT bars upto10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, rough finished surfaces of flat, concrete not exceeding 200mm thick (Horizontal or sloping),etc complete all as specified and directed.

Formwork to rough finished surfaces of concrete, edges of concrete flats, treads, breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, etc complete all as specified and directed.

Demolition of brick work or stone masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc, but excluding aslar facings,dresse stone work and percast conrete articles complete all as specified and directed.

Supply and fix Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, concealed pipe line, including cutting holes or grooves in brick wall/rcc and making good with cement mortar 1:3 complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors concealed pipe line, including cutting holes or grooves in brick wall/rcc and making good with cement mortar 1:3 complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) bends any radius including cutting holes or grooves in brick wall/RCC and making good with cement mortar 1:3 complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) bends any radius with access doors including cutting holes and making good with cement mortar 1:3 complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) bends any radius including cutting holes and making good with cement mortar 1:3 complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) bends any radius with access doors including cutting holes and making good with cement mortar 1:3 complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door including cutting holes and making good with cement mortar 1:3 complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

Material and labour PVC (SWR) gully trap 125/10mm setting and jointing solvent cement complete all as specified and directed by Engr-in-charge

Material and labour for repairing of soffit of RCC slab and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any situation (including provn of support, formwork and welding of reinforcement with weld mesh of weight not less than 3 kg/ sqm and dubbing 1st coat of 20 to 25mm thick in CM 1:3 finished rough and finishing coat of 10mm thick in CM 1:3 finished even and smooth without using extra cement after applying cement slurry @ 3.00 Kg/Sqm and applying three coats of white wash complete all as specified and directed. Note : (i) Unit rate of this items includes the cost of scaffolding, form work etc and nothing extra shall be paid on account of variation of heights (ii) The measurement of finished plaster of 2nd coat provided on surface in sqm shall be the mode of measurement aganst this item.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

Material and labour for brickwork with sub class 'B' bricks, straight or curved on plan exc 6 m mean redius, built in cement mortar 1:6 complete all as specified and as directed.

Material and labour half Brick wall with sub-class 'B' bricks old size straight or curved on plan to any radius built in cement mortar 1:4 and complete all as specified and as directed.

Material and labour 5 mm thick rendering with mixing water proofing compound in cm 1:4 to be finished even and smooth with out using extra cement over 10mm thick rendering on faces of brick work or concrete surface in cm 1:4 finished even and fair complete all as specified and as directed. Note : WPC will measured and paid seprately

Supply only Liquid water proofing compound complete all as specified and as directed.

Material and labour Rendering 15mm thick in cement mortar 1:6 on brick work or concrete surface and finished even and smooth without using extra cement and complete all as specified and directed.

Material and labour for rendering 10mm thick in ceiling in cement mortar 1:3m finished even and smooth complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

Material and labour for preparation of plastered or un-plastered old surfaces of wall and applying one coat of white wash to wall complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of oil bond distemper over a coat of alkali-resiatant priming paint complete all as specified and directed.

Material and labour Preparation of old plastered surfaces of wall and applying two coat of oil bound distemper (washable) white or tinted over one coat of alkali resistant primer and including complete removal of existing treatment on wall complete all as specified and directed.

Material and labour for preparation new ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Material and labour for preparation of old plastered or un-plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of cement base paint (camoflauge pattern) over one coat of alkali resistant primer all as per manufactures instructions complete all as specified and directed.

Complete removal of exsting treatment on walls and applying two coats of cement base paint (camoflauge pattern) over one coat of alkali resistant primer all as per manufactures instructions complete all as specified and directed.

Taking down DB/ main switch/sheet metal enclousure of any size and making good disturbed surface of wall/ floor complete all as specified and directed. Note:- Temporary power supply shall be provided by contractor.

Taking out carefully the existing burnt sub main wiring of size 4 Sqm / 6 Sqmm PVC insulated multi stranded aluminum/copper conductor cable along-with earth continuity conductor from the PVC/rigid steel, concealed/surface conduit and making good the distubed surface all as specified and directed.

Taking down carefully point wiring (Light, fan, socket) complete including fittings such as switches, Ceiling roses, pendants, regulator, sockets etc removing from site of work and making good to the disturbed surfaces of walls/floors etc all as specified and directed Note:- Temporary power supply shall be provided by contractor.

Supply and laying Sub main wiring complete with 03 runs (Phase, Neutral & Earthing colour code) of single core 4 sqmm fire retardant low smoke (FRLS) PVC insulated copper conductor cable multistranded and sheathed LT 1100 V grade drawn through and including non metalic regid PVC medium conduit 20 mm dia ISI marked and allaccessories including cutting chasing in walls for concealed wiring using mechine and making good the disturbed surface complete all as specified and directed. Note :- 3 run of 4 sq mm cable, 1 run of PVC conduit cable shall be measured as single unit length.

Supply and laying Sub main wiring (concealed) complete with three single core 6 sqmm fire retardant low smoke (FRLS) PVC insulated unsheathed multi stranded copper conductor cable LT 1100 V grade drawn through in 20 mm dia non metalic regid PVC medium conduit and conduit accessories including 6 sqmm fire retardant low smoke (FRLS) PVC insulated unsheathed multi stranded copper earth cable connected to common earth dolly complete including cutting chasing in walls for concealed wiring using mechine and making good the disturbed surface complete all as specified and directed Note :- 3 run of 6 sq mm cable, 1 run of PVC conduit cable shall be measured as single unit length.

Material and labour for Point wiring (concealed) with PVC insulated fire retardant low smoke (FRLS) multi stranded copper conductor cable of 1.5 sqmm in and including PVC concealed nonmetalic rigid conduit heavy duty (ISI mark) and pressed steel terminal boxes (for mounting switches / sockets /regulators / ceiling roses etc) made out of MS sheet not less than 1.6 mm and 6cm depth including painting with one coat of red oxide primer on internal and external surface covered with 3mm thick laminated plastic sheet ISI marked including 1.5 sqmm PVC insulated fire retardant low smoke (FRLS) multi stranded copper conductor cable as earth continuity wire connected to common earth and each terminal box/fitting complete all as specified and directed. (a) One light point/bell point controlled by one switch

All as per description of serial item No.122.00 but One ceiling fan point controlled by one switch complete all as specified and directed.

All as per description of serial item No.122.00 but One exhaust fan point contrelled by one switch complete all as specified and directed.

All as per description of serial item No.122.00 but One switch socket outlet 3 pin 6 Amp on same board complete all as specified and directed.

All as per description of serial item No.122.00 here in before but one 3 pin socket outlet 5 Amp on indipendent board complete all as specified and directed.

All as per description of serial item No. 122.00 here in before but for for One 3-pin socket outlet 15 Amp on independent board with 4 sqmm FRLS cable including 2.5 sqmm FRLS multistranded copper cable as earth continuity wire complete all as specified and directed.

Supply and fixing energy saving decorating box type batten light fitting 230 volts surface mounted complete with high effeciency glare free light LED lamp 20 watt blue coloured end caps with all accessories, pre- wired, including providing flexible copper wire twin core cable complete all as specified and directed by enginer in charge. Make :- Havells cat part No batten LHEXBXPNIN1W020 HSN code 9405 or equivalent in Crompton/Philips /Wipro

Supply and fixing LED light fitting, 1x10 w Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head luminaries Back-lit LED luminaire comprising of high brightness LEDs complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 hz complete all as specified and directed. Make havell Cat Part No HEXAFT10WLED857SSYMBOPC HSN Code 9405 or equivalent in Crompton/Philips /Wipro.

Suply and fixing Lamp holder angular PVC polycrbonate type with back plate suitable for PVC casing capping/conduit fitting complete all as specified and as directed. Make :- Anchor/Plaza/Crabtree

Supply and fix LED bulb 9 watt with lumen 850 complete all as specified and directed. Make :- Havell Cat Part No LHLDEUEEMC8R009 or equivalent in Philips/Crompton/Wipro

Supply and fix LED mirror light 10W stout Plus LED complete range of industrial LED battens to replace traditional T8 battens 600 mm legth with industrial grade heavy duty driver having THD<10%.

Supply and fixing in repair stepped type electronic fan regulator 100/120 watt , SP 230 Volt 100 watt complete all as specified and directed.

Supply and fix socket out let 5 pin 6 amp multipurpose, flush type complete all as specified and directed.

Supply and fix Socket out let 2 in 1, 3 pin, 5 and 15 amp multipurpose, flush type complete all as specified and directed.

Supply and fix Switch piano flush type single pole one way 5/6 amp complete all as specified and directed.

Supply and fix bell push flush type single pole one way 5/6 amp complete all as specified and directed.

Supply and fix Switch piano flush type single pole one way (multi pin) 16 amp complete all as specified and directed.

Supply and fix Ceiling rose surface Bakelite 65 x 50 mm three terminals complete all as specified and directed.

Supply and fix Bell, AC, 230 volts, single pole complete all as specified and directed.

Supply and fixing in Repair sheet metal enclosure single pole and neutral with two pin and earth plug and socket complete with provision for fixing of one MCB SP 20 Amps complete all as specified and directed.

Supply and fixing vertical TPN DB double door suitable for fixing 100 amp MCCB, IP 45 protection with powder coated enclosure 4 way insulated busbar assembly rating 200 Ampswith and including MCCB 4 pole, 415 V, 100 A, 16 kA - 01 No complete all as specified and directed. Make : Havells Cat part No DHDLVDRWGOFO04 HSN No 8537 or equivalent in IndoAsian/ Legrand/ ABB.

Supply and fix sheet metal enclosure for SPN DBs with double door for incorporating MCBs IP 43, 8 way with 200 Amp rated busbar, 240 volts as per IS 8623, DBs, all as specified and directed. Make :- Legrand /L&T/Havells

Supply and fix MCB SPN 32 Amps 10 KA 240 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of lugs etc. complete all as specified and directed. Make :- Legrand /L&T/Havells

Supply and fix MCB SP 32 Amps 10 KA 'C' curve 240 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of lugs etc. complete all as specified and directed. Make :- Legrand /L&T/Havells.

Supply and fix MCB SP 6 to 20 Amps 10 KA 'C' curve 240 volts 50 Hz including making necessary incoming and outgoing connection with suitable size of lugs etc. complete all as specified and directed. Make :- Legrand /L&T/Havells.

Material and labour for taking dowon ceiling fan after diconnection of electric cable and removing the same to MES store yard for reuse complete all as specified and directed.

Material and labour for servicing, painting of ceiling fans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust refixing the ceiling fan in orginal position and connecting all as specified and directed.

Material and labour for taking down geyser of any capacity after disconnecting of electric connection and deposit in MES store for reuse complete all as specified and directed.

Material and labour for cleaning and servicing of electric geyser after that refixing the geyser in orginal position and connecting all as specified and directed.

Material and labour for taking down single phase KWH meter after disconnincting of electric connection including cleaning and dusting after that the same has deposit to MES store for reuse complete all as specified and directed.

Material and labour for concealed single phase KWH meter box of size 35 x 25 x14 cm made out of CRCA sheet 3mm thick powder coated to protect from rust with and including arrangement for fixing SPN MCB and complte all as specified and directed.

Fixing only as in repairs KWH meter single phase and making connection with suitable size of copper cable complete all as specified and directed. Note:- (i) KWH meter shall be issued from MES store free for fixing only. (ii) Cost of Cable for connection shall be deemed included in the unit quoted rate of this item.

Material and labour for earthing complete with GI earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.50 Mtr below ground level. The earth plate to be connetced with earth lead of 4 mm dia galvanised iron or steel wire all as shown in para no 4 the earthing test point all as specified and directd.The GI earthing strip to be protected by galvanised iron pipe 40 mm bore (medium grade) up to ground level and there after with 40mm dia HDPE pipe up to test point. Earthing shall be include with providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) up to 90 cm all around earth plate further filled with 60 cm thick Tibba sand and 2nd layer with 30 cm of Magnesium sulphate powder (compact thickness ) , 3rd layer with tibba sand up to the ground level. Earthing shall also be include for providing concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and not exeeding 1.5 m deep, getting out the excavated earth bottom surface to required gradient complete all as specified and as directed.

Returning filling in, and including spreading and leveling in layers not exceeding 25 cm thick complete all as specified and as directed.

Material and labour for removal of excavated material such as soils at a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

Material and labour for sand cushioning using dry and clean tibba sand in two layers, first layer of 80 mm thick before laying of cable and second layer of 150 mm thick after laying of cable in trenches/ ducts including consolidation of each layers complete all as specified and directed. Note : Punned thickness (18 cm) shall be measured and paid.

Material and labour well burnt old size sub Class ‘B’ bricks, laid flat, in trenches for cable protection complete all as specified and as directed.

Taking out old uncerviceable cable XLPE/PVC sheathed 1100 volts grade armoured with aluminum conductor of any size from trenches, wall, poles, under floor etc complete all as specified and as directed.

Suplying, laying, jointing and testing of under ground cable XLPE insulated, 1100 volt grade heavy duty armoured with stranded aluminium conductor 3.5 core 35 sq mm laid in trenches/ duct/pipe including all electrical connection with required lugs and nuts, bolts complete complete all as specified and as directed.

All as per item No 161.00 above but 25 sq mm 4 core complete all as specified and as directed.

Material and labour boring of road crossing of size 80 mm dia at suitable depth not less than 1 m by using machinery / equipments complete without damaging the surface for passing pipes / cables etc including removing excavated soil to a distance n exc 50m complete all as specified and as directed. Note : (i) Location of boring holes shall be decided by the Engr-in-Charge as per requirement, nothing extra shall be payable on account of variation in length of crossing of road etc. (ii) During boring soil strata may be changed, hence nothing extra shall be paid to the contractor for boring of holes through different strata/different type of soil. Tenderer is hereby advised to keep in mind this aspect while quoting his rates.

Supplying and laying as in repairs 40 mm bore GI tubing light grade incl all accessories for passing of cables for mechanical proctection, laid under Plinth / Floors/ Paths Culverts or fixed on wall or concealed in wall / floor or along poles or as street light poles or as street light mounting bracket with complete accessories such as bends / sockets / reducers / saddles incl necessary threading / drilling works complete all as specified and as directed.

M/S BUDHRAM BISHNOI