Renovation work for smart look of building external area at Rampurhat Super Speciality Hospital, Dist. Birbhum -Electrical Installation work.

Amount

Supply, installation, testing & commissioning of fabricated Chanellium Letter (Sign Board) fo hight 2ft of following specification: ( "রামপুরহাট গভর্নমেন্ট মেডিক্যাল কলেজ এন্ড হাসপাতাল" : 36 nos albhabets X 24 inch= 864 Inch)

a) Each side of the letter would be made of 50mm breadth, 1.2mm thick Alluminium Sheet with the help of suitable cutting & bending machine.

b) Back side of the letter would be made from 2mm thick Alluminium Sheet by cutting according to appropriate letter block with the help of suitable cutting & bending machine.

c) Front side of the letter would be made of 4mm thick Mitshubishi or equivalent make imported Acrylic Sheet by cutting according to appropriate letter block with the help of suitable cutting & bending machine. The Color of the letter will be approved by the appropriate authorirty of the Hospital/Medical College.

d) For glowing each letter, Samsung or equivalent make (0.97 - 1.02)W LED module would be used. (Make will be approved by the EIC)

e) To provide power for LED module, suitable SMPS unit of IP-67 would be used in respect of load of each letter. And the power supply unit would be fixed in suitable MS or equivalent box of IP-65 on parapet wal or iron structure with appopriate clamp. (Make will be approved by the EIC)

f) All side of the letters (only side & back wall) would be painted with synthetic enamelled/PU paint. (Color & Make will be approved by the EIC)

g) The inter-connection of SMPS unit & LED mobule circuit of each letter would be made with FR PVC insulated sheathed copper wire. And the letter complete in all respect would be fixed on pre-errected MS structure by suitable SS nut-bolt & washer - as per direction of EIC.

(Above rate is considered including loading, unloading & transportation & all other charges.)

Febrication & errection of suitable Iron Structure would be made with 75*40*5 mm 'C' Iron Channel as vertical support on floor/roof, 50*50*5 mm Iron Angle for continuous horizontal frame supprot for top & bottom of each letter & cross angle support to structure, 50*5mm Iron Flat for continuous horizontal frame supprot for middle of each letter. A Sole plate of size 300x300x5mm would be welded at the bottom of each vertical support and suitable sole plate in case of cross support. The complete structure would be painted with two coats Red-Oxide Primmer & two coats Synthetic Enamelled paint. The structure would be errected on roof supported to parapet wall. (The work would be executed as per direction of EIC.

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. [using concrete mixture ratio: 1:1.5:3, Pakur Variety] (at the roof of the G+4 building) (PWD Building SOR Page: 26 Item: 10)

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (at the roof of the G+4 building) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary. (With 1:6 cement mortar, 20 mm thick plaster) [including cost of chipping over concrete surface] (at the roof of the G+4 building) (PWD Building SOR Page: 192 Item: 15)

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. (at the roof of the G+4 building) (PWD Building SOR Page: 192 Item: 15)

Dismantling of existing Signage Board from roof top of SSH Building.

Supply, Delivery, Installation, Testing and commissioning of waterproof LED driver for existing damaged signage board of Academic Building with following specification. Input: 170-264 V, AC, 1.5 - 2.38 A, 50 HZ, Output: 12 V, DC, 16.7 A, 200 watt, IP: 67 (Make: Reputed)

Supply & Delivery surface and wall mounted led batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver having THd<10%. High efficiency 20 watt T8 LED linear lamp (for Wall mounted) Make: Havells lumiline Plus BS20WLED865SPCSS, Philips, Bajaj

Supply & Delivery LED Batten for LED Tube Light Model: Havells Regal Batten T8 UPTO2X22WSSBSWH Make: Philips/Similar Crompton/Similar Havells

Supply of 1 no. “L” type MS clamp, 2 nos. fastener & 2 nos. bolts-nuts. [to fix “L” type MS clamp (125mmx125mm) 6mm thick and 25mm width in ceiling with the help of suitable size 2 nos. fastener & other end 25 cm long 20 mm dia EI conduit (14 SWG) with suitable size bolts and nuts.]

Drilling 2 nos hole on downrod.

Supply & Delivery T8 LED Tube Light 20 watt Make Havells PHOTONULTRA2.01213T8SSTL20WLED865SPC, Philips, Bajaj

Supply & delivery of LED PL-L 18W, CCT: 6500K Make: Philips, Model: 2G11

Supply & delivery of 4 pin type lamp holder for fixing of 18 watt 4 pin LED PL-L Lamp inside the 2'x2' conventional fittings (Make- any reputed)

Supply & Delivery of Recess/surface mounted 36 watt LED luminaire Cat no. Wipro CRCO10R038HP57GL1, Philips, Bajaj

Supply & Delivery of Recess/surface mounted 12 watt Round LED luminaire Make: Philips; Model No: 59435; Product Code: 929002630901

Supply & Delivery of Recess/surface mounted 18 watt Round LED luminaire Make: Philips; Model No: 59437; Product Code: 929002631501

Supply and delivery of 5W Square AP Plus UltraGlow LED Down Light (CDL) with Driver; Box Cut-out 7.5cm X 7.5cm (FOR LIFT) Make: Philips, Bajaj, Wipro

Prava Enterprise

B.P.CONSTRUCTION

BANERJEE CONCERN