PROVN OF ELECTRIC SUPPLY, PIPE LINE AT 2 AHQ, AIR PURIFIERS , WATER TANKS, PARKING AND REFRIGERATOR ETC UNDER GE(U) E/M MEERUT

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft /loose soil complete all as specified.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes,pier holes, laying of pipe and cables etc. but not exceeding 10 sqm on plan including dressing/trimming sides and levelling/grading & ramming bottom of excavation and getting out in soft/loose soil complete all as specified.

Returning ,filling in , including spreading , levelling , watering and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations / mass concrete complete all as specified.

M&L Reinforced Cement concrete M-25 ( design mix) as in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Supply only Integral water proofing compound complete all as specified and directed.

M&L Brick work with old size fly ash bricks., straight or curved on plan exc 6 m mean radius , built in CM 1:6, complete all as specified and directed.

Use and waste of formwork to flat soffits of suspended deck slabs, floor slabs, landings and similar work; not exceeding 200 mm thick ( Horizontal or sloping) surfaces finished fair as specified in SSR Part-I Clause 4.11.16.2(a) as specified complete all as specified.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs exceeding 10 cm and not exceeding 20 cm wide and sides of RCC/PCC bands in walls , horizontal or sloping and similar work surfaces finished fair in forms complete all as specified.

M&LHigh strength deformed bars or twisted bars ( TMT) 10 mm dia and over as in reinforcement , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. or higher complete all as specified.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade (ISI) marked , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

S&F Gunmetal , globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore dia. iron pipe and fixed complete all as specified.

S&F Rotational moulded poly-ethylene water storage tanks (ISI marked) ( cylinderical vertical with closed top ) 1000 litres capacity ,hoisted and fixed in position complete all as specified.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210 gms.) complete all as specified.

M&L for making hole in 150mm dia GI/DI/CI pipe line including cutting of pipe where required for making branch connections , including S&F mild steel clams made out of 40x6 mm flat iron duly fitted with suitable size of GI socket suitable for taling 25mm nominal bore pipe complete all as specified and directed.

M&L for construction of Brick masonry valve pit of 610mmx610mmx840mm internal size consisting of Mild steel frame and cover complete complete all as specified and shown in drawing No. CEBZ drg No. TD/EM/12

M&L 25mm nominal bore mild steel galvanised water tubing, medium grade with all fittings like bends, elbows, Tee, reducers, sockets, unions etc laid in trenches complete all as specfied and directed.

M&L 20mm nominal bore mild steel galvanised water tubing, medium grade with all fittings like bends, elbows, Tee, reducers, sockets, unions etc laid in trenches complete all as specfied and directed.

S&F Gunmetal , gate valves, with iron wheel head, screwed both ends for 25 mm bore dia. iron pipe and fixed complete all as specified.

Supply, installation and commissioining of porttable AIRPURIFIERS ,6 stage physical filtration and light weight , touch panel and maintaining the air upto 0.3 micron consisting HEPA filter, Activated carbon filter, Photo Catalyst filter ( Ti02 Titanium dioxide), 15 Ultravoilet (UV) LED Bulbs, Negative ions and 800 sqft area covered, clean air delivery rate (CADR) -420 cum per hour, 4 speed fan, auto mode ( based on dust and Odour sensor ) silent mode, power consumption -65 watt (approx) , filter replacement indicator complete all as specified and directed.

Supplying and fixing 80mm nominal bore Galvanised mild steel pipe /tubing, light grade for protection of earth lead / passing cable complete with all fittings, laid in trenches / under roads, drain, paths, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers complete all as specified of the following bore (Excavation & Earth work , Mild steel clamps, bolts , nuts and washers shall be measured and paid separately)

M&L fly ash old size bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

Material and labour for river sand, unwashed and screened dry ) for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . (Note:Punned thickness shall be measured for the purpose of payment)

M&L for auguring of hole suitable for passing 40mm to 100mm bore pipe in true horizontal position under road, PCC paths etc., by means of mechanical ring/ auger after doing ultrasound to prevent any damage to existing cables pipe line specified and directed coming in the route not exceeding 1.5 m in depth below existing surface level of road and not excd 30M in length complete all as specified. Note: Pipe shall be measured and paid separately under appropriate items and any dahage to existing cables of anytype shall be made good by the Bidder without any extra cost to department.

M&L Earthing complete with galvanised mild steel earth plate electrode 600x600x6mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI strip 32 x 6 mm as earth strip electrode bolted or rivetted to earth plate at one end and connected at another end, GI earth strip encased in and including 40 mm dia GI 'Light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'medium grade' as water pipe from earth chamber to upper edge of earth plate, GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 40mm thick precast RCC 1:2:4 type B-1, duly reinforced with 8 mm dia TMT high strength deformed bars @ 150mm c/c, 6mm dia MS round bar as in lifting handles, and mild steel angle iron frame 40mmx40mmx5mm for pit cover, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate number 3 of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

Supplying, installing, commissioing and testing of LT switchgear panel board of size 1200mmx1000mmx500mm (min) , IP-54 (outdoor type) , 415 Volts, 50 Hz, AC supply, three phase and neutral ( 4 wire) , 750 Amps Aluminium bus bars , 4 pole , cubical type, factory made out of 3.15mm thick CRCA sheet structure mounted on Platform (as per Sketch), rigid mild steel angle iron frame of 50mmx50mmx5mm with 400mm long extended legs grouting in PCC platform , duly epoxy powder coated internally and externally with approved shade, rubber gasketted, hinged front and back openable doors with proper locking arrangements for dust and vermin proof ,complete including suitable size cable allay, lugs , cable glands and making connections with MCCB spreaders,/ wiring with suitable size SC PVC insulated copper conductor cable, locking arrangements 65mm size and lock with keys comprising of the followings and specified hereafter:-

MCCB 4 pole,500Amps, 415V, 36 kA, 50 Hz, with adjustable thermal magnetic release, -01 No.(incoming)

LED type indication lamps ( R-Y-B) with holder panel mounting type complete all as specified. -01 No.

MCCB 4 pole, 400Amps, 415V, 16 kA, 50 Hz, with adjustbale thermal magnetic) release, -02 Nos.(outgoing)

MCCB 4 pole, 250Amps, 415V, 16 kA, 50 Hz with adjustble thermal and adjustable magnetic) release, 50 HZ, -02 Nos.(outgoing)

Onload Changeover Switch 630 Amps, 4 pole, 50 Hz, 415 Volts, open execution type-01 No (outgoing)

Drawings of LT panel shall be got approved from GE before procuring.

Supplying, installing, commissioing and testing of LT switchgear panel board of size 1200mmx800mmx400mm (min) , IP-54 (outdoor type) , 415 Volts, 50 Hz, AC supply, three phase and neutral ( 4 wire) , 600 Amps Aluminium bus bars , 4 pole , cubical type, factory made out of 3.15mm thick CRCA sheet structure mounted on Platform (as per Sketch), rigid mild steel angle iron frame of 50mmx50mmx5mm with 400mm long extended legs grouting in PCC platform , duly epoxy powder coated internally and externally with approved shade, rubber gasketted, hinged front and back openable doors with proper locking arrangements for dust and vermin proof ,complete including suitable size cable allay, lugs , cable glands and making connections with MCCB spreaders,/ wiring with suitable size SC PVC insulated copper conductor cable, locking arrangements 65mm size and lock with keys comprising of the followings and specified hereafter:-

MCCB 4 pole,400Amps, 415V, 36 kA, 50 Hz, with adjustable thermal magnetic release, -01 No.(incoming)

LED type indication lamps ( R-Y-B) with holder panel mounting type complete all as specified. -01 No.

MCCB 4 pole, 250Amps, 415V, 16 kA, 50 Hz, with adjustbale thermal magnetic) release, -02 Nos.(outgoing)

MCCB 4 pole, 160Amps, 415V, 16 kA, 50 Hz with adjustble thermal and adjustable magnetic) release, 50 HZ, -02 Nos.(outgoing)

Drawings of LT panel shall be got approved from GE before procuring.

Supplying, laying or fixing, jointing and testing LT under ground electric power cable Crossed linked polyethylene ( XLPE Cable) insulated, galvanised steel strip or wire armoured, ISI-7098 marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of 150 sqmm 3 1/2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc.( Excavation, earth work, sand cushioning, protection bricks/ tiles/ block,clamps, nuts , bolts, washers and pipe shall be measured and paid separately under appropriate items ).

Supplying, laying or fixing, jointing and testing LT under ground electric power cable Crossed linked polyethylene ( XLPE Cable) insulated, galvanised steel strip or wire armoured, ISI-7098 marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of 240 sqmm 3 1/2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc.( Excavation, earth work, sand cushioning, protection bricks/ tiles/ block,clamps, nuts , bolts, washers and pipe shall be measured and paid separately under appropriate items ).

Excavating in post holes in soft/ loose soil ( or similar holes) each n exc 0.5 cu.m. getting out, returning,filling in and ramming earth or broken rubble mixed with earth around , in layer not exceeding 25 cm, watering and removing surplus soil to a distance n.exc 50 M complete all as specified.

M&L Rolled mild steel in roof trusses, ( framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing ( Beam, tee,angle,channel or flat sections ) including distance pieces , cleats etc. Fe-410W grade A complete all as specified.

M&L Rolled mild steel in rolled sections as in main and cross beams, hip and jack rafters ; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410 W grade A complete all as specified.

S&F Pre-painted galvalume( hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon, AZ 150 gm/sqm both side) , Zincalume (steel) based corrugated sheet 0.50mm thick ,of an approved colour, having tensile strength of 550 Mpa, and finished with resin coat on both surfaces as in roof covering/ cladding to wall,including flashings , ridges, valley etc fixed with self tapping screws complete all as specified ( Roof area shall only be be measured for the purpose of payment )

M&L 0.63 mm thick galvanised plain mild steel sheeting , grading of coating 275, in ridges, hips, Valley gutters, drip and straight flashings ( length and girth as fixed) complete all as specified.

M&L preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamelled paint over one coat of red oxide Zinc chrome primer complete all as specified.

M&L broken bricks Hardcore of gauge n exc. 63 mm , deposited , spread and levelled in layer n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L Plain cement concrete 1:3:6 ,type C2 , using 40 mm graded crushed stone aggregate,75 mm thick as in sub base complete all as specified.

M&L Plain cement concrete type B1 , using 20 mm graded crushed stone aggregate,50mm thick as in floor top finished even and smooth without using extra cement complete all as specified.

Supply and installation of refrigerator electric driven ( Single phase) 320 litres capacity , frost free, double door with 2 star rating complete all as specified of make Samsung, Godrej, Whirlpool/ LG

S&F automatic volatge stabliser wall mounted with input correction range of 140V to 280V and output range Volatge 225 Volts + 11% with digital display features of high and low out of range volatge shutdown and time relay 2 to 3 min on initial start capacity 1 KVa of make Sinetrac/ Blue bird/ Logicstat

Jain Traders

Manish Enterprises

BASANT RAM AND SONS