SITC of CCTV Cameras in Lifts and Common areas Installation of Intercom Systems inside Lifts Segregation of Residential and market entry DG Fencing and Construction of Male and Female toilet at each Cluster at Golf Homes and Kingswood project located at Plot No 2 Sector 4 Greater Noida West UP 201301

Grand Total(DSR + NON-DSR) 1,78,85,000.00

ABSTRACT OF COST (CIVIL, ELETRICAL & PLUMBING WORKS)

S. DSR 23 C.I @ 3% DSR-Amount MR-Amount

Ref. No Description Unit Quantity

No. Rate Correction (Rs.) (Rs.)

1.0 EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including

dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated

soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.

2.25 in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and Cum 50.00 196.00 196.43 9,821.46

watering, lead up to 50 m and for all lift.

2.0 CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone

aggregate 40 mm nominal size)

3.0 REINFORCED CEMENT CONCRETE

Centering and shuttering including strutting, propping etc. and removal of form for all heights:

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 200.00 961.30 963.41 1,92,681.05

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 25.00 736.40 738.01 18,450.32

Providing and laying in position machine batched and machine mixed design mix M-25 grade

cement concrete for reinforced cement concrete work, using cement content as per approved

design mix, including pumping of concrete to site of laying but excluding the cost of

centering, shuttering, finishing and reinforcement, including admixtures in recommended

5.33.2.1 proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability Cum 40.00 9860.40 9881.99 3,95,279.77

without impairing strength and durability as per direction of Engineer-in-charge.“(Note :-

Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per

design mix is payable/recoverable separately).All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete upto plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kilogram 3700.00 107.85 108.09 3,99,918.91

Providing and rebarring by using chemical grout (Hilti RE 500/RE 200) following the

manufacturer's printed installation instructions (MPII). Drilling, hole cleaning, mortar injection,

and rebar installation will be done as per the specified procedures to ensure proper

embedment and alignment, with the use of automated systems for accurate chemical dosing.

The work shall be carried out as per the technical specification and approved by the

Engineer-in-Charge.

Add for using extra cement in the items of design mix over and above the specified cement

content therein.

Core cutting of 110 mm diameter in RCC, including all necessary equipment, labour, and

tools, complete with proper packing, sealing, and finishing to ensure a watertight (leak-proof)

condition, complete in all respects as per site requirements and Engineer-in-Charge

4.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundation and plinth in:

a) 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 47.50 7132.25 7147.87 3,39,523.81

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10

3.08 6.34 average compressive strength in super structure above plinth level up to floor V level in :

a) 6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) Cum 95.00 8752.55 8771.72 8,33,313.22

Brick work 7 cm thick with common burnt clay F.P.S. (non modular) brick of class designation

6.9 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and Sqm 180.00 865.65 867.55 1,56,158.24

upto floor five level.

5.00 FINISHING

13.1 12 mm cement plaster of mix :

13.2 15 mm cement plaster on the rough side of single or half brick wall of mix:

Providing and applying white cement based putty of average thickness 1 mm, of approved

13.80 brand and manufacturer, over the plastered wall surface to prepare the surface even and Sqm 1150.00 156.05 156.39 1,79,850.51

smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve even shade and colour.

6.0 FALSE CEILING

Digitally signed by MAYANK

S. DSR 23 C.I @ 3% DSR-Amount MR-Amount

Ref. No Description Unit Quantity

No. Rate Correction (Rs.) (Rs.)

Providing and fixing false ceiling at all height including providing and fixing of frame work

made of special sections, power pressed from M.S. sheets and galvanized with zinc coating

of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25

mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia

bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length

with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the

ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each

having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular

to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high

12.45 having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with

the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and perimeter channel with the help of dry

screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of

tapered and square edges of the board with recommended jointing compound , jointing tapes

, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and

two coats of primer suitable for board, all as per manufacturer’s specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and

direction of the Engineer in Charge but excluding the cost of painting with :

12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board Sqm 120.00 1529.10 1532.45 1,83,893.85

7.0 MARBLE WORK

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved make, in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed

with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS:15622, of approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

11.41A sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the

joints with white cement and matching pigments etc. The tiles must be cut

with the zero chipping diamond cutter only . Laying of tiles will be done

with the notch trowel, plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently and easily

Glazed Vitrified tiles Matt/Antiskid finish of size

8.00 DOOR & WINDOW

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative

type, core of block board construction with frame of 1st class hard wood and well matched

teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of

9.20.2 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm 58.00 3167.95 3174.89 1,84,143.49

Providing wood work in frames of doors, windows, clerestory windows and other frames,

wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia

& length (hold fast lugs or dash fastener shall be paid for separately).

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block

30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal

Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction

hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated

9.147.D Using R1 series with frame (33 mm & above ) x (35 mm & above) & sash /mullion (33 mm &

1.1 above) x (50 mm & above). (Height upto 0.90 metre).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with

necessary screws etc. complete (Copper oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with

screws etc. complete (Copper oxidised as per IS 1378)

9.00 SANITARY FITTING

Supply, installation, testing and commissioning of glazed vitreous china wash

basin with R.S. or C.I. brackets painted white with padestrain to conceal waste pipe, 32mm

C.P. brass waste of standard pattern , C.P brass wall flange 32 mm dia. C.P. brass bottle

trap and union 32 mm dia C.P, Angle Valve, Wash Basin Trap, Waste Pipe connecting to Cp

Jali, pipes to wall flange. complete including cutting and making good the walls wherever

White Vitreous China Wash basin size 630x450 mm with bib cock long body with wall flange.

Providing & fixing beveled edge mirror 5.5mm thick (60X45cm) of superior quality plate glass

complete with CP brass screws and as per design including polishing.

Providing and fixing white vitreous china pedestal type water closet (European type W.C.

pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe,

17.2 with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making good the walls and floors wherever required

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 16 6515.55 6529.82 1,04,477.10

Providing & fixing Hand Shower (Health Faucet) with 8mm dia, 1M long PVC tube and wall

hook CP brass wall flange

Digitally signed by MAYANK

S. DSR 23 C.I @ 3% DSR-Amount MR-Amount

Ref. No Description Unit Quantity

No. Rate Correction (Rs.) (Rs.)

18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin

of 430x260x350 mm sizes respectively with manual flushing angle valve with standard flush

MR-6 pipe, waste connection pipe and C.P. brass spreaders with brass unions and G.I clamps Each 8 3,273.81 26,190.48

complete, including painting of fittings and brackets, cutting and making good the walls and

floors wherever required :

10.0 MARKET GATE ENTRY

Providing, fabricating, supplying and fixing M.S. framed mesh fencing of height 1.20 m (4 ft) for enclosure of DG set

area, including access gate at each location with all accessories, frames and locking arrangement, complete in all

respects as per approved design and direction of Engineer-in-Charge.

1. Supporting Pillars

Providing and fixing M.S. posts made of 100×50×4 mm rectangular hollow section, spaced at suitable intervals (approx.

3.0 m c/c), including. Embedding in RCC Column/Masonary Work of required size. Proper alignment, levelling, curing

and finishing. Base plates, anchor fasteners wherever required.

2. Fencing Frame

Providing and fabricating M.S. frame panels using 50×50×6 mm M.S. angle for outer framing 50×6 mm M.S. flat as

stiffeners/support members Cutting, welding, grinding, edge finishing complete

3. Mesh / Jali Work

MR-7 Providing and fixing 3 mm thick M.S. jali / welded wire mesh of approved pattern inside the frame, including: Proper Sqm 931 710.13 6,61,131.03

stretching and fixing by welding/clamping Ensuring rigidity and uniform alignment

4. Surface Preparation & Painting

Thorough cleaning, removing rust, scale, oil etc. Applying one coat of steel primer (red oxide/zinc chromate) Finishing

with two coats of synthetic enamel paint of approved shade

5. Erection & Completion

Including: Transportation, loading/unloading Erection, alignment, fixing in position Testing for stability and safety

Making the complete fencing system ready for use.

6. Civil work like PCC, RCC, Masonary Works, Plaster Works paid separately, However dismentaling, Reparing,

Painting on MS structure work are inclusive in the rates.

Providing, fabricating, supplying and fixing sliding type M.S. gate of 1.80 m (approx. 6 ft) height & required grill work for

market separation, made out of structural steel sections, including all fittings, fixtures, accessories and finishing complete

as per approved design and direction of Engineer-in-Charge.

1. Main supporting pillars:

Providing and fixing M.S. pillars made of 100×100×5 mm square hollow section, embedded in PCC foundation of

suitable size (e.g., 1:2:4 mix) including excavation, concreting, curing and finishing complete.

Fabricating outer frame using M.S. rectangular hollow section 100×50×4 mm including cutting, welding, grinding and

3. Infill members:

Providing internal members using M.S. square pipe 50×50×2 mm or equivalent, placed vertically/horizontally as per

approved pattern.

4. Sliding track arrangement:

Providing and fixing 150 mm M.S. C-channel embedded/fixed in ground with proper alignment, including 20 mm dia

M.S. round bar track welded/fixed over channel for smooth movement.

5. Roller assembly:

Supplying and fixing heavy-duty roller wheels (minimum 2–4 nos. as required) with ball bearings, suitable brackets, base

MR-8 plates, and alignment for smooth sliding operation. Sqm 350 6,629.30 23,20,255.00

6. Guide system:

Providing top and side guide rollers/brackets to ensure proper alignment and prevent tilting during operation.

7. Locking arrangement:

Providing and fixing complete locking system including sliding bolt, tower bolt, hasp & staple, provision for padlock,

stopper, end catchers and locking plate as required.

8. Accessories:

Including all necessary items such as base plates, anchor fasteners, clamps, stoppers, end plates, caps, handles, etc.

9. Surface preparation & painting:

Cleaning, rubbing and removing rust using emery/power tool Applying one coat of approved steel primer (red oxide/zinc

chromate). Finishing with two coats of synthetic enamel paint of approved shade and brand

10. Erection & completion:

Including loading, unloading, transportation, hoisting, fixing in position, alignment, testing for smooth operation and

making the gate fully functional.

Rate inclusive of all civil works like Dismentaling, Repairing, PCC, RCC, Steel work, Etc.In this regard nothing will be

11.0 WATER PROOFING

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by

applying cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement

compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second

22.5 layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ Sqm 115 617.5 618.85 71,168.02

0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for

48 hours. (The rate includes preparation of surface, treatment and sealing of all joints,

corners, junctions of pipes and masonry with polymer mixed slurry.)

12.0 PLUMBING WORK

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe

with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and the cost of cutting chases and making good the same including testing of

joints complete as per direction of Engineer in Charge. Concealed work, including cutting

chases and making good the walls etc.

18.8.2 20 mm nominal dia Pipes Mtr 85 537.60 538.78 45,796.07

18.8.4 32 mm nominal dia Pipes Mtr 70 739.30 740.92 51,864.33

Providing, laying and fixing uPVC soil, waste and vent pipe of 110 mm diameter conforming

to relevant IS standards, including all fittings such as bends, tees, offsets, junctions,

couplers, access doors, etc., jointing with rubber ring / solvent cement joints, cutting and

making good the walls and floors, including clamping with MS clamps, supports, testing of

joints, and making the system complete in all respects as per direction of Engineer-in-Charge.

13.0 ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call

bell point with 1.5 sq.mm FRLS/HFFR PVC insulated

copper conductor single core cable in surface/

recessed medium class PVC conduit, with modular

1.10.1 switch, modular plate, suitable GI box and earthing E/pt. 104 1189.00 1,23,656.00

the point with 1.5 sq.mm FRLS/HFFR PVC insulated

copper conductor single core cable etc. as required.sheet, suitable size M.S. box and

earthing the point with 1.5sq.mm. FRLS PVC installed copper conductor single core cable etc

as required. Group A

Digitally signed by MAYANK

S. DSR 23 C.I @ 3% DSR-Amount MR-Amount

Ref. No Description Unit Quantity

No. Rate Correction (Rs.) (Rs.)

Supplying and fixing metal box of following sizes

(nominal size) on surface or in recess with suitable

size of phenolic laminated sheet cover in front

including painting etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire p/mtr 30 334.00 10,020.00

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution

board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/Isolator) (A) 6Way Double door

Supply of 12'(300mm)sweep 1400 rpm heavy duty Exaust Fan complete with ring, blade etc

as required. ISI marked.

Installation of exhaust fan in the existing opening, including making good the damage,

connection, testing, commissioning etc. as required.

Supplying and fixing of following sizes of medium

class PVC conduit along with accessories in

1.21.2 surface/recess including cutting the wall and making p/mtr 76 168.00 12,768.00

good the same in case of recessed conduit as

required. A)25 mm

Supplying and fixing 5amps,to 32 amps rating, 240 volts, "C" curve miniature circuit breaker

2.10.1 suitable for inductive load of following pole in the existing MCB DB complete with connection Each 32 256.00 8,192.00

testing and commissioning etc, as required. (A) Single Pole

Supply and fixing following rating, double pole, 240 volt, isolator in the existing MCB DB

2.12.2 complete with connection, testing and commissioning etc. as required. (A) 63 Amp. each 8 527.00 4,216.00

Laying of one number pvc insulated and PVC sheathed/ XLPE power cable of 1.1 kv grade of

following size in the existing surface as required

Upto 35 sq. mm (clamped with 1mm thick saddle)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

S/I/T/C of LED tube type luminaire 20 watt rating complete with extruded aluminium batten

prewired with high efficient LEDs with the following :

Total system wattage 20 watt +/- 5 %

Luminous efficacy lumens/watt >=95

MR-11 Power factor >=0.95 Each 50 460.96 23,048.00

Supplying and fixing following modular switch/ socket

on the existing modular plate & switch box including

connections but excluding modular plate etc. as

1.23.4 3 pin 5/6 amps socket outlet Each 16 136.00 2,176.00

1.23.5 6 pin 15/16 amps socket outlet Each 16 219.00 3,504.00

Supply of PVC/XLPE insulated PVC/XLPE sheathed Al. conductor armoured cable for

working voltage up to 1.1 kv confirming to IS 7098(part-1) of following size

Digitally signed by MAYANK

SUBJECT: CCTV Installation in Project

ABSTRACT OF COST (CCTV WORK)

Sr. No. Ref. No Description Unit Qty Amount

Supply Installation Testing and commissioning of 8 channel NVR , ONVIF compliant

, Certification CE, FCC, UL, BIS, recording bandwidth 320 Mbps , output interface 1

x HDMI (up to 4K), 1 x VGA , Alarm in/out :8ch in / 4ch out , 1 X RJ-45 port (1000M)

, Bit Rate 16kbps-20mbps per channel, Sync Playback 4/8 ch playback, iOS

smartphone support , 1 HDD support , support upto 8 TB HDD , , 1x3.0 USB for

backup /upgrade , 2x 2.0 USB for mouse, Display resolution up to 4K, 1 ESata Port,

1 MR-13 RS-485 Port, Cloud Storage, Net HDD, Edge analytics : Face Detection, Heat Map, NOS 56 18,009.43 1008528.08

Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection,

Stationaary Object Detection, Motion Detection, Tempring Detection, Rare Sound

Detection, License Plate Detection. Defog, Protocol support:- HTTp, TCP/IP, IPv4,

UPNP,RTSP,UDP, SMTP,NTP,DHCP,DNS, IPilter, PPPOE, DDNS,FTP,IP search,

P2P, NFS/SMB/CIFS, IPC Management complete etc as required.

Supply Installation Testing and commissioning of 32 channel NVR , ONVIF

compliant , Certification CE, FCC, UL, BIS, recording bandwidth 320 Mbps , output

interface 1 x HDMI (up to 4K), 1 x VGA , Alarm in/out :16ch in / 4ch out , 1 X RJ-45

port (1000M) , Bit Rate 16kbps-20mbps per channel, Sync Playback 4/8/10/16/32 ch

playback, iOS smartphone support , 2 HDD support , each HDD slot support upto 8

TB HDD , , 1x3.0 USB for backup /upgrade , 2x 2.0 USB for mouse, Display

resolution up to 4K, 1 ESata Port, RS-485 Port, Cloud Storage, Net HDD, Edge

2 MR-14 analytics : Face Detection, Heat Map, Human & Vehicle Detection, Pedestrian NOS 2 24,986.18 49972.36

Intrusion Detection & Line cross Detection, Stationaary Object Detection, Motion

Detection, Tempring Detection, Rare Sound Detection, License Plate Detection.

Defog, Protocol support:- HTTp, TCP/IP, IPv4, UPNP,RTSP,UDP,

SMTP,NTP,DHCP,DNS, IPilter, PPPOE, DDNS,FTP,IP search, P2P,

NFS/SMB/CIFS, IPC Management complete etc as required.

Supply Installation Testing and commissioning of 2 MP Dome camera with stqc

Supply Installation Testing and commissioning of 5 MP Bullet camera with stqu

Supply Installation Testing and commissioning of Surveillance Class 4 TB HDD for

Recording. It should support 24x7 usage complete etc.as required.

6 MR-18 Supply 24'' LED DISPLAY NOS 60 12,001.67 720100.20

Supply Installation Testing and commissioning of 8 portPoE+ Switch with 8 x

7 MR-19 10/100/1000BASE-T and 2x 1G SFP+ uplink ports, minimum switching capacityof NOS 62 11,004.99 682309.38

Supply Installation Testing and commissioning of HDMI 4K Cable as per required.

Supply Installation Testing and commissioning of 2U wall mount rack with fans , 2

Nos. of hardware pkts 2 PDUs with 3x15A power supply points mesh-screen front

and rear lockable doors, ventilated top cover with cable glands etc.complete as

Supply Installation Testing and commissioning of 4Uwall mount rack with fans , 2

Nos. of hardware pkts 2 PDUs with 3x15A power supply points mesh-screen front

and rear lockable doors, ventilated top cover with cable glands etc.complete as

Supply Installation Testing and commissioning of RJ 45 connetctor for user and

Supply Installation Testing and commissioning of 25mm PVC with saddling and

bend, shocket complete as required.

Supply Installation Testing and commissioning of cat6 4pair cable LSZH for cctv

work complete as required.

Supply Installation Testing and commissioning of following length of UTP 23 AWG

14 MR-26 Factory crimped CAT6A Patch cord RoHS compliant complete as required. 1MTR NOS 70 193.80 13566.00

15 MR-27 Supply Installation Testing and commissioning of 12core flatwire 180 mtr MTR 7020 189.65 1331343.00

Supply Installation Testing and commissioning of armoured 6 core Singlemode

OS2 (9/125 Micro) fiber cable , Corrugated ECCS Armor, HDPE (UV) Sheathing,

Theoxtropic gel filled OFC cable with 2 Nos steel music wire embedded in side

sheathing as stregth member for switch connectivity. Cable should be ROHS

compliant and as per IEC60749-1 with product warranty of 30 years.

Digitally signed by MAYANK

SUBJECT: CCTV Installation in Project

ABSTRACT OF COST (CCTV WORK)

Sr. No. Ref. No Description Unit Qty Amount

Supply, Installation, Testing & Commissioning of 12F SM loaded LIU with LC

adaptor plates, pigtel cables, Spilce tray, cable holder and 4 nos of cable entry exist

point with rubber gurment along with the LIU, Powder Coaded 1.2mm steel sheet

metal, 1U etc complete as required. LIU should be in accordance with YD/T 778-

2006 Optical Distribution Frame & YD/T 1272.1-2003 Optical Fiber Connector Part

1: Type LC and should have 30 years of product warranty.

Supply, installation, testing, and commissioning of Fibre Termination Box (FTB) for

CCTV system, suitable for terminating optical fibre cables, complete with splice

trays, adapters, pigtails, connectors, and all necessary accessories, including proper

dressing, labeling, and fixing on wall/rack as required. The item shall include fibre

splicing, testing, and ensuring proper signal transmission, complete in all respects

as per specifications and directions of the Engineer-in-Charge.

19 MR-31 Supply, Installation, Testing & Commissioning of 1g SFP Module. Nos 124 2,996.96 371623.04

20 MR-32 Supply, Installation, Testing & Commissioning of LC to LC patch fiber cord . Nos 124 1,100.50 136462.00

Total amount 76,92,618.88

Total amount 76,92,618.88

Digitally signed by MAYANK

SUBJECT: Intercom EPBX system for lifts in Project

ABSTRACT OF COST (Intercom Work)

Sr. No. Ref. No Description Unit Qty Amount

Supply Installation Testing and commissioning of 4 Line intercom

Supply Installation Testing and commissioning of analogue Phone

recever metal cabinet

Supply Installation Testing and commissioning of Speaker phone for

inside and out side lift

Supply Installation Testing and commissioning of 4core flatwire 180

Total amount 14,11,325.42

Total amount 14,11,325.42

Digitally signed by MAYANK