Construction of library with sanitary complex at Khanqah Bogdang. (Under Distt. Capex)

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30cm in depth,1.5m in width as well as10 sqm on plan) including getting out and disposa lof excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.All kinds of soil @70%

Ordinary Rock @15%

c)Hard rock (blasting prohibited) Manual Means @15%

Earth work in excavation by manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil @ 90%

Ordinary Rock @10%

Dry stone pitching (any thickness) excluding cost of stones. On Horizontal

Providing and laying in position cement concrete1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form work for : A)Foundations, footings, bases of columns, etc. for mass concrete

B)Columns, Pillars, Piers, Abutments, Posts and Struts

C)Suspended floors, roofs, landings, balconies and access platform.

D)Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Edges of slabs and breaks in floors and walls. Above 20 cm wide

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :1:3:6 (1 Cement: 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 6 fine sand ).

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer.

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm).

Providing wood work in frames of doors, windows clearstory windows and other frames, wrought framed and fixed in position. Second class Kail wood Frame of doors and window.

Providing and fixing panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for seperately,all complete as per direction of Engineer-in-charge.(second class teak wood 35 mm thick shutter)

Providing and fixing 250MM HIGH ladakhi type ornamental Pentsak with local talboo (Complete Balti Architecture shingtsak) including polish of desired shade all complete Job, as per designed specification or instruction of engineer incharge

Providing and fixing ladakhi type ornamental Kaju with 2nd class Kail wood or equivalent (Complete Balti Architecture Kaju) including artistic carvings of Balti architecture of carve depth and width of minimum 20mm and polish of desired shade all complete Job, as per designed specification followed by instruction of engineer incharge 14'6" high Kaa (wooden post) AVG 12" DIA WITH CARVINGS of groove depth 1"

Providing and fixing ladakhi type ornamental Kaju with 2nd class Kail wood or equivalent (Complete Balti Architecture Kaju) including artistic carvings of Balti architecture of carve depth and width of minimum 20mm and polish of desired shade all complete Job, as per designed specification followed by instruction of engineer incharge Kaju (Column Head) each 29.4 sft

Providing and fixing ladakhi type ornamental Kaju with 2nd class Kail wood or equivalent (Complete Balti Architecture Kaju) including artistic carvings of Balti architecture of carve depth and width of minimum 20mm and polish of desired shade all complete Job, as per designed specification followed by instruction of engineer incharge 10' high Kaa (wooden post) AVG 8" DIA WITH CARVINGS of groove

Providing and fixing ladakhi type ornamental Kaju with 2nd class Kail wood or equivalent (Complete Balti Architecture Kaju) including artistic carvings of Balti architecture of carve depth and width of minimum 20mm and polish of desired shade all complete Job, as per designed specification followed by instruction of engineer incharge Kaju (Column Head) each 2.6 sft

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Kiln seasoned and chemically treated hollock wood 35 mm thick

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture of wood work (Hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size asapproved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3. (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with;Budloo wood

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing ISI marked mortice lock set.300 x 16 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250 x 10 mm

Providing and fixing bright finished brass handles with screws etc. complete:125 mm

Providing and fixing strips in joints of terrazzo/ cement concrete floors. Glass strips 40 mm wide and 4 mm thick

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

Constructing masonry Chamber 30x30x50 cm, inside with precast cement concrete solid block in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design:Inside dimensions 500x700 mm and 45 cm deep for single pipe line with one or two inlets

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Carriage of Sand and C.Agg from an average lead up to 15km by mechanical transport.

Carriage of excavated earth at an average lead up to 150m by head load

Carriage of excavated earth from an average lead up to 2.0 km by mechanical transport. Qty vide item no. 1,2

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area beyond 3 sq. metres

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Carriage of malva/stone aggregate above 40mm at an average lead of 250m by head load

Carriage of malva/stone aggregate above 40mm at an average lead of 2 km by MT

Providing and fixing toilet paper holder :C.P. brass

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level P.V. C. flushing cistern including flush pipe (of approved make) "manually controled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests. JAGUAR/CERA Make

Providing and fixing Flexible (coil shaped) PVC waste pipe for ( wash basin & kitchen sink ) 40 mm dia with length not less than 700 mm i/c PVC waste fittings

15 mm C.P. brass 2 in 1 tap

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

PVC door junction 110 mm dia

15 mm C.P. brass tap

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) by way of self regulating heat cable / K -flex wire 19 mm / tape/ rock wool / chicken mesh /black polythine/28/26 guage aluminium sheet with screws including labour charge . complete as per direction of Engineer in Charge. PN-16 pipe , 25mm OD(SDR-7.4) a).32mm OD(SDR-7.4)

. 40mm OD(SDR-7.4)

c). 50mm OD

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357mm

Providing and fixing ladakhi type ornamental Kaju with 2nd class Kail wood or equivalent (Complete Balti Architecture Kaju) including artistic carvings of Balti architecture of carve depth and width of minimum 20mm and polish of desired shade all complete Job, as per designed specification followed by instruction of engineer incharge Kaju (Column Head) each 4.5 sft

12 Module (200mmX150mm)

Providing and fixing CP brass basin mixer pillar tap of approved quality and make

Providing and fixing CP brass bib cock of approved quality and make.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: Waste coupling 31 mm of 79 mm length and 62 mm breadth weighing not less than 45 gms.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore

Supply installation testing and commissioning of Instant Geyser 30ltr Capacity of approved brand (Havells/Bajaj/Crompton or any othet approved brand as per engineer in charge including all fixtures , bolts all complete

Providing and fixing soil waste & vent pipe PVC Pipe 110mm dia(10 ft unit length)

PVC Pipe 75mm dia(10 ft unit length)

PVC Collar 110mm dia

PVC Collar 75mm dia

PVC trap 110mm dia

PVC trap 75mm dia

PVC Socket 110mm dia

PVC Socket 75mm dia

Providing and fixing CP brass stop cock of approved quality and make.

PVC door junction 75mm dia

Electrification Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC Conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Providing and fixing of 1.0HP self priming regenerative electric motor water pump, of a brand approved by the engineer incharge, complete job.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

5 WATTS FOOT LIGHTS

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch

3 pin 5/6 A socket outlet

15/16 A switch

6 pin 15/16 A socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.20mm

Cast Iron C.I. Junction Box, Size: 25 mm, 4 Way

FAN box

Providing and fixing floor jali

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way,Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 Amps

Supplying and fixing following rating, four pole, 415 V, MINIATURE CIRCUIT BREAKER(MCB) in the existing DB complete with connections, testing and commissioning etc. as required.63 Amps

Supplying and fixing following rating, four pole, 415 V, Residual current circuit breaker (RCCB) having a sensivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 Amps

Providing and fixing danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply, installation, testing & commissioning of cubicle type compartmentalized floor mounted free standing with separation system as per IS:8623 part 1 for 415V, 50HZ, 3phase 4 wire AC supply, moisture, dust and vermin proof IP-55, L.T.Panel boards, made out from 2mm thick CRCA sheet steel duly epoxy powder coated (by seven tank process ) in approved colour, complete with interconnections / control/ power wiring with FRLSH copper conductor wires & 6A SP MCBs for control circuits ,communicable meters shall be with software, high conductivity Aluminium bus bars, earth bus,Bus bar supports, removable 3mm thick gland plates on top & bottom, M.V. danger notice plate , louvers and following incomer and outgoing feeders (outgoings will be with ON indication with 6A control MCB) complete as per specifications(SLD) and drawings :

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

4 Module (125mmX75mm)

8 Module (125mmX125mm)

Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round /square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as requiredwith Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C) 5 - 7 watt

10W LED MIRROR LIGHTS

WALL LAMP(10W)

Installation, testing and commissioning of the following 1500 rpm exhaust fans including louvered shutters etc. complete as required.300mm

Supply,Laying, Testing& commissioning of under ground cable one metre below ground level covered with sand and R.C.C covers of suitable size as per requirement for mechanical protection to the cable,including necessary connections, digging in all classes of soil and refilling with primary compaction of trenches for following sizes XLPE(E) 11KV insulated ISI marked and of approved make.Aluminium conductor armoured cables suitable for working voltage upto 11000 volts including proper dressing of the cable in an approved manner complete as required and as per specifications.3.5 core, 95 Sq.mm.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1kV grade as required .3.5 core, 95 Sq.mm.

Supply and laying of RCC Hume pipes (150MM Dia) for cable entry including the cost of excavation, back filling of excavated material, compaction and Concreteing and installation of cable marker as required