IMPROVEMENT TO ORDERLIES SINGLE LIVING IN ACCN SUPPER BAR AND ALLIED WORKS AND PROVISION OF BATHROOM AND MISC B/R WORK AT SUB STATION OF SITE-II AND SP-65 AT AF STATION LAITKOR PEAK UNDER GE (I) (AF) SHILLONG

Amount

Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as directed.

Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as directed by Engr- In- Charge.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as directed.

Dismantling timber scantlings 40 sqcm and over in section for unframed work, in any position all as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15 mm dia

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20 mm dia

Demolition of reinforced cement concrete of any description and in any position complete all as specified.

Demolition of cement concrete of any description and in any position complete all as specified.

Demolition of Precast concrete block/ Brickwork or stone/boulder masonry, laid with cement morter complete all as directed.

Material and labour for Use and waste of flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed.

Material and labour for Reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies deck slabs, and in shelves and the like complete all as specified and directed. Note: Reinforcement and formwork shall be measured and paid separately.

Material and labour for cement concrete type B0, 1:2:4 (12.50mm graded aggregate), rounded or chamfered on edges in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping kneelers, apex stones, bed plates, kerbs not provided for roof kerbs or mud stops, rounded or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including water proofing compound complete all as specified

Material and labour 75 mm thick PCC type C2, 1:3:6 using 40 mm graded crushed stone aggregates as in sub-floors, sub- bases, floors and pavings, plinth protection including finishing the concrete surface even & smooth without using extra complete all as specified.

Material and labour for Hardcore of broken stone or boulder gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified.

Material and labour 25 mm thick PCC type B1, 1:2:4 using 20 mm graded crushed stone aggregates as in floor surfaces including finishing the concrete surface even & smooth without using extra cement complete all as specified.

Material and labour for precast cement concrete block masonry with solid blocks 1:3:6 type C1 using 20 mm graded crushed stone aggregates, exc 10 cm in width and setting in cement mortar 1:6, complete all as specified.

Material and labour for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers & binders, cut to length, bent to shapes required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Supply and fix Fe-410-W(Gde?E-250) qualityA Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified.

Supply and fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified.

Supply and fix compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. confirming to Fe 410-W (Gde-E- 250) quality-A complete all as specified.

Supply and fix 6 mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified.

Material and labour 2nd class hardwood Plain fillets. square,rectangular or triangular in section, clean sawn, secured with nails or brads exceeding 3 sqcm but not exceeding 6 sqcm complete all as specified.

Material and labour 40 mm thick PCC type B1, 1:2:4 using 20 mm graded crushed stone aggregates as in floor surfaces including finishing the concrete surface even & smooth without using extra cement complete all as specified.

Material and labour for 38 mm thick glass dividing strips, 3 mm thick complete all as specified.

Supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

Supply and fix powder coated aluminium door, window and ventilator shutters powder coating of any colour (Thickness or powder coating not less than 50 micron), side hung/ sliding type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

Supply and fix 5.50 mm thick sheet glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified.

Supply and fix PVC door frame of size 50 mm X 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified.

Supply and fix 30 mm thick factroy made solid panel PVC door shutter (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with neat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuct inside the solvent cement for style and single side pre laminated PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rails and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded to the style and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification .

Supply and fix as in repair harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified.

Supply and fix 200 mm long aluminium anodised barrel tower bolts of extruded section all as specified.

Supply and fix 100 mm long medium weight, cold rolled mild steel, Butt hinges, complete all as specified.

Supply and fix 150 mm long aluminium alloy handles, fabricated type, anodized all as specified.

Supply and fix as in repairs 100 mm long hasp and staple, of aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified.

Material and labour for 10 mm thick rendering on stone masonry surfaces or surface other than fair face of brick or concrete surfaces in cement mortar 1:6 finshed even and smooth without using extra cement complete all as specified.

Material and labour for preparation of newly plastered wall surface and applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified.

Material and labour for complete removal of existing treatment of old plastered wall surface and applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified.

Material and labour for 15 mm thick rendering in cement mortar 1:4 in two layers (10 mm +5 mm) on external faces of brick wall or concrete surfaces, finished the surfaces even and smooth without using extra cement with using approved Liquid Water Proofing Compound on second layer (5 mm) as per manufacturer instruction complete all as specified and as directed by Engineer-In-Charge. Note: Liquid Water Proofing Compound shall be measured and paid including this item

Material and labour for 5 mm thick rendering in cement mortar 1:3 on fair faces of ceiling surfaces, finished the surfaces even and smooth without using extra cement complete all as specified.

Material and labour for preparation of old plastered or unplastered ceiling surfaces including brooming down or steel wire brushing , scrapping down smoke, soot , moulds , moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash with roller finish complete all as per manufacturer instruction

Material and labour for preparing newly plastered surfaces and applying three coats of white wash on ceiling/soffits of chajjas complete all as specified and directed.

Material and labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces.

Material and labour for prepration new or previously untreated wood or wood base materials of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Material and labour for preparation of old painted wooden surfaces of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Material and labour for complete removal of existing old plastered surfaces of wall and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm.

Material and labour for prepration new or previously untreated steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Material and labour for 7 mm thick joint free premium quality glazed ceramic colour tiles of size 600 mm x 300 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified.

Material and labour for 7 to 8 mm thick joint free premium quality anti skid colour ceramic tiles size of each tiles should be 400 mm x 400 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces including 20 mm thick screed bed in cement mortar 1:4 complete all as specified.

Material and labour for 10 mm thick joint free premium quality double charged vitrified ceramic tiles of size 600 mm x 1200 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces laid over 20 mm thick screed bed in cement mortar 1:4 complete all as specified.

Material and labour for 10 mm thick joint free premium quality double charged vitrified ceramic tiles of size 600 mm x 1200 mm as in skirting/ dado/ vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified.

Material and labour for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20 mm thick screed bed in cement mortar 1:4, including edge moulding of counters vanities etc. and machine polishing to edge to give high gloss finish etc. including demolition complete all as specified.

Material and labour for 12 mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including edge moulding of counters vanities etc. and machine polishing to edge to give high gloss finish etc. including demolition complete all as specified.

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

Supply and fix as in repairs Vitreous China wash basin, white, flat back, size 550 mm x 400 mm including 32 mm dia waste fittings and waste pipe including brackets complete all as specified. Make Johnshon / Jaquar / Cera/ Parryware

Supply and fix as in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste coupling and waste pipe; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410mm x 330mm x 160mm complete all as specified. Make: Diamond/ Nirali/ Grohe/ Kohler

Supply and fix as in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified. Make:-Blue Star & Silver Shine/ Prayag Polymer Pvt. Ltd./ Polytuff

Supply and fix as in in repairs 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified.

Supply and fix as in repairs PVC flexible/collapsible sink/wash basin waste pipe drain hose/ outlet pipe of 31 x 32 x 950 mm as spesified and directed

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but not exceeding 20 cm girth complete all as specified.

Supply, lay and fix 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. Make: Surya Roshni ltd/ Tata/ Jindal Steel/ Prakash/ Bansal/ Zenith/ Nezone Tubes Ltd

Supply, lay and fix 20 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. Make: Surya Roshni ltd/ Tata/ Jindal Steel/ Prakash/ Bansal/ Zenith/ Nezone Tubes Ltd

Supply and fix as in repairs soap dish holder (polycarbonate) as per manufacturer instruction. Make:- Jaquar / Parryware/ Johnson

Material and labour for second class hardwood scantling wrought sawn complete all as specified.

Supply and fix for 15 mm bore dia of pipe Brass CP Wall mixer 3 in 1 for mixing hot & cold water screwed down for iron pipe and fixed complete all as per manufacturer instruction. Make:- Parryware Cat No G3317A1/ Jaquar Cat No CQT-23281UPR/ Johnson Cat No T6023C

Supply and fix as in repairs brass CP overhead shower rose with or without swivel joints, size of 190 mm x 295 mm Rectangular Shape Single Flow (Body & Face Plate Stainless Steel) with Rubit Cleaning System, including fixing to stainless steel pipe or union as per manufacturer instruction. Make:- Jaquar / Parryware/ Johnson

Supply and fix as in repairs, brass CP single lever basin mixer for mixing hot and cold water including 15 mm bore hot water pipe duly insulated with glass wool and aluminium cladding complete all as specified. Make:- Parryware Cat No G3165A1/ Jaquar Cat No COP-001BPM / Johnshon Cat No T6045C

Supply and fix as in repairs 15 mm bore quarter turn Bib taps, chromium plated, cast copper alloy, with wall flange concealed type screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified. Make Johshon Cat No T3305C/ Jaquar Cat No FUS-29037/ Marc Cat No MCT-1030

Supply and fix as in repairs 15 mm dia cast copper alloy chromium plated Angle valves, with wall flange concealed type screwed down for iron pipe of for unions complete all as specified and directed. Make :- Parryware Cat No T3907A1/ Cera Cat No F1016201/ Johnson Cat No T5310C

Supply and fix as in repairs Rotational moulded polyethylene water storage overhead tanks (cylindrical vertical with closed top) multi layered 1000 ltr capacity hoisted and fixed in position including 25 mm dia Ball valves (Minimum weight of valve 455 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified. Make:Sintex/ Astral/ Finolex/ Supreme

Supply and fix one piece Vitreous China wash down water closet pan floor mounted, white including fixing bolts, 10 ltr capacity flushing cistern,flush pipe plastic water closet seat white including jet spray, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices and also including 'P' or 'S' trap including taking out old pedestal alongwith existing all fittings and making the surface match with existing surface complete all as per manufacturer instruction. Make of Pan Parryware Verve AM / Cera CAMPBELL/ Johnshon COSMO

Supply and fix as in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified.

Supply and fix as in repairs vitreous china squatting pan of Orrisa pattern size 580 mm x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including 'P' or 'S' trap and lime concrete bedding connection making good to floor all as specified. Make Parryware Cat No C0117* / Cera Cat No COVY S3010104/ Johnshon Cat No P0461PW

Supply and fix as in repairs 10 ltrs capacity PVC valveless syphonic action type, low level flushing cistern, white with inlet, ball valve float and handle including brackets and 32 mm dia PVC low or high density flush pipe complete all as per manufacturer instruction Make Parryware Cat No E8109 / Cera Cat No B1020101/ Johnshon Cat No P2831PW

Supply and fix as in repairs 75mm dia PVC (SWR) floor trap, plain with gratings including jointing with solvent cement complete all as specified and directed. Make: Jain Irrigation/ Kisan/ Supreme/ Prince/ Reliance/ Oriplast

Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified. Make: Jain Irrigation/ Kisan/ Supreme/ Prince/ Reliance/ Oriplast

Supply and fix 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. Make: Jain Irrigation/ Kisan/ Supreme/ Prince/ Reliance/ Oriplast Note: Quoted rate is deemed to be included for necessary Bend, Junction, branch piece, reducer and any other fittings required for fixing.

Supply and fix 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. Make: Jain Irrigation/ Kisan/ Supreme/ Prince/ Reliance/ Oriplast Note: Quoted rate is deemed to be included for necessary Bend, Junction, branch piece, reducer and any other fittings required for fixing.

Supply and fix as in repairs 75 mm dia PVC (SWR) vent cowl complete all as specified and directed. Make: Jain Irrigation/ Kisan/ Supreme/ Prince/ Reliance/ Oriplast

Material and labour for 75 mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregates complete all as specified.

Supply and fix bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified.

Supply and fix as in repairs, stainless steel kitchen plate rack of size 36 x 36 x 10 inch made out of 0.85 mm thick stainless steel sheet complete all as per manufacturer instruction. Make: Prayag/ Nirali/ Blue Star & Silver Shine

Supply and fix as in repairs 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified.

Supply and fix as in repairs 12 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified.

Supply and fix as in repair 30 mm width of flaps (when open) continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as per specified.

Supply and fix ball catches with 8 mm dia steel ball, and brass body and striking plate of 140 mm length ncluding letting in and fixed complete all as specified.

Supply and fix Pavement floor vitrified tiles of size 300x 300x 10 mm thk (Endura tiles of Johnson or equivalent makes listed in List of Makes) of approved colour and design set and jointed in neat cement slurry and pointed in white or coloured to match including 20 mm th screed bed in cement mortar 1:4 complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified.

Excavation in trenches not exc. 1.5 m wide not exc. 1.5 m in depth; for laying of cables not exc. 10 Sqm on plan and getting out , trimming sides, forming bottom surface to required level complete in hard/dense soil all as specified and as directed.

Material and labour for Cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregates as in foundations, filling and mass-concrete complete all as specified.

Material and labour for 75 mm thick Cement (PCC) concrete 1:4:8 type D2 using 40 mm graded stone aggregates as in hardstanding/ sub bases finished the surfaces even and rough complete all as specified.

Supply and fix mild steel screw bolts (machine made) of dia 16-20 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.50 cm but not exc 30 cm long complete all as specified and directed.

Supply and fix roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W (Gde-E- 250) quality-A complete all as specified.

Material and labour for 15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finshed even and smooth without using extra cement complete all as specified.

Returning filling in soft/loose soil, including, spreading, levelling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated materials (soils) not exc 50.00mtr and depositing where directed at a level not exc 1.50 mtr above the starting point in soil, complete all as specified and as directed.

Material and labour for cutting holes in circular shape in brick walls exceeding half brick but not exceeding one brick thick in cement mortar for fixing exhaust fan and making good disturbed surfaces in cement mortar (1:3) finished even and smooth and to match with existing as required complete all as specfied and as directed.

Supply and fix 4.00 mm thick frosted glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified.

Material and labour for 10 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4 finshed even and rough complete all as specified.

Supply and fix as in repairs CP health faucet with tube and wall hook including all fittings as per manufacturer instruction. Make: Parryware Cat No T9961A1/ Jaquar Cat No ALD-579 / Johnson Cat No S0826C

Supply and fix anodised aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, 4 lever mortice lock, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified.

Material and labour for reinforced cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggreagates as in foundation including rafters footings foundation beam plinth beam bases for column etc basement slab under reamed piles and mass concrete complete all as specified and directed. Note: Formwork and reinforcement shall be measured and paid separately.

Material and labour for use & waste of formwork to sides of square, rectangular or polygonal pillars, posts, columns etc for flat rough finished surfaces complete all as specified and directed.

Material and labour Reinforced cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregates as in Columns, pillars, piers, posts and struts complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately

Material and labour for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Supply and fix as in repairs Rotational moulded polyethylene water storage overhead tanks (cylindrical vertical with closed top) multi layered 500 ltr capacity hoisted and fixed in position including 20 mm dia Ball valves (Minimum weight of valve 210 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified Make:Sintex/ Astral/ Finolex/ Supreme

Taking down carefully aluminium/copper point wiring (light,fan,socket or power) of any type complete, including fixtures and fittings such as switches,ceiling roses,pendants,regulators sockets, light fittings etc. removing materials to stores for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls,floors,ceiling etc.,all as directed

Material and labour for point wiring with 1.50 Sqmm PVC insulated un sheatned multi stranded copper conductor cable (FRLSH) 1100 volts grade two single core conforming to IS-694-1990 and one run of continious earth wire with 1.50 Sqmm PVC insulated unsheatned stranded copper conductor cable (FRLSH) draw in and including heavy duty 20 mm dia PVC conduit (ISI marked) in concealed with all necessary fittings and fixures and switch, socket, regulator, fan point, exhaust fan point etc. including making good disturbed surface with CM (1:4) to match with the existing surface complete all as specified for the following :- Note:- (a) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (b) Quoted rates shall be deemed for conduit, cutting chases of wall, making good disturbed wall. (c) The metal flush box with modular cover plates with frame measured and paid separately. Make: Finolex(ISI Marked)/ Polycab(ISI Marked)/ Nicco (ISI Marked)/ Havells (ISI Marked)/ RR Cable(ISI Marked)/ KEI (ISI Marked)

One light/ fan/ exhaust fan/ bell point controlled by one nos, one way switch

One 5 pin 6 Amps switch socket outlet point controlled by one switch on independent board.

One 5 pin 6 Amps switch socket outlet point controlled by one switch on same board with other switches

All as per Item No 113.00 but One 3 pin socket outlet. 15 amps, independent, with cables 2.50 sq. mm size complete all as specified.

All as per Item No 113.00 but One 3 pin socket outlet. 15 amps, independent, with cables 4.00 sq. mm size complete all as specified.

Supply and fix as in repairs Modular type Switch , flush type single pole one way 10 Amps 240V.

Supply and fix as in repairs modular socket outlet , 2 module, 3 pin 6 Amps 240 V flush type .

Supply and fix as in repairs Modular type Switch , flush type single pole one way 20 Amps 240V.

Supply and fix as in repairs Modular socket outlet 2 module , 3 pin 6 to 16 Amps 240 V flush type .

Supply and fix modular metal flush box with modular white cover plate with frame , 1 or 2 module complete all as specified. Make: L&T/ Legrand/ Havells/ Anchor/ Schneider/ Hager

Supply and fix modular metal flush box with modular white cover plate with frame , 3 module complete all as specified. Make: L&T/ Legrand/ Havells/ Anchor/ Schneider/ Hager

Supply and fix modular metal flush box with modular white cover plate with frame , 4 module complete all as specified. Make: L&T/ Legrand/ Havells/ Anchor/ Schneider/ Hager

Supply and fix modular metal flush box with modular white cover plate with frame , 6 module complete all as specified. Make: L&T/ Legrand/ Havells/ Anchor/ Schneider/ Hager

Supply and fix as in repairs Switch piano, flush type single pole two way 6 Amps 240V.

Supply and fix as in repairs switch socket combination, 2 in 1, 5 pin 6 Amps 240 V ,flush type.

Supply and fix as in repairs socket outlet , 3 pin 6 Amps 240 V flush type .

Supply and fix as in repairs switch socket combination, 2 in 1, 6 pin 6 Amps and 16 Amps 240 V ,flush type.

Supply and fix as in repairs Switch piano, flush type single pole two way 16 Amps 240V.

Supply and fix as in replacement LED lights fitting 1x 18W, 220V, warm white/ pure white AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specifed and directed. Note:- (a) LM-80 certificate from NABL accredited Lab shall be submitted for LED light fittings. (b) Warranty certificate shall be submitted for LED light fitting as per standered format for minium 50000 Hrs. (c) LED light fitting and drivers shall be of same make.

Supply and fix as in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC warm white/ pure white decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specifed and directed. Note:- (a) LM-80 certificate from NABL accredited Lab shall be submitted for LED light fittings. (b) Warranty certificate shall be submitted for LED light fitting as per standered format for minium 50000 Hrs. (c) LED light fitting and drivers shall be of same make.

S & F in repairs two pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 'C' Series 20 Amps, 240 Volts complete all as directed. Make: ABB/ Siemens/ Schneider/ Legrand/ Hagger/ L&T/ GE

Supply and fix as in repairs ceiling rose surface baklite with three terminals 240 V. Make: L&T/ Legrand/ Havells/ Anchor/ Schneider/ Hager

Supply and fix as in repairs lamp Angular holder insulated body with back plate suitable for batten fittings all as specified. Make: L&T/ Legrand/ Havells/ Anchor/ Schneider/ Hager

Supply and fixing sub-main wiring with PVC insulated & unsheathed two run of 6.00 Sqmm single core multistrand copper conductor cable (FRLSH), 1100 Volt grade alongwith single run of 6.00 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH) 1100 Volt grade, connected to common earth dolly as earth continuity conductor, drawn through minimum 25 mm PVC conduit including taking down existing wiring complete all as specified and directed. Note:- (a) PVC conduit in concealed including accessories shall be measured and paid including the item. (b) 2 Run of line conductor and 1 Run of earth continuity conductor shall be measured as one unit length. (c) Cable requireds for connection to MCBs/DBs shall be deemed to be included in the unit rate. (d) Rate shall be included for cutting, pinning in, making good to facings where required for pointing in cement mortar 1:3 and cutting chases for concealed conduit wiring and making good, and cutting not exceeding 10 cm girth. Make:Finolex(ISI Marked)/ Polycab(ISI Marked)/ Nicco (ISI Marked)/ Havells (ISI Marked)/ RR Cable(ISI Marked)/ KEI (ISI Marked)

Supply and fix as in replacement sheet metal enclosure MCB DB SPN with din rail 08 way 240 V (double door type) with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc. and making good of disturbed surface to match with existing colour of wall complete all as specified. Make: ABB/ Siemens/ Schneider/ Legrand/ Hagger/ L&T/ GE Note: (a) Quoted rates shall be deemed for brick wall / concrete wall cutting and making good as per existing surfaces.

Supply and fix as in repair MCB SP 240 volts, 50 Hz capacity 6-32 Amps 'B' curve all as specified. Make: ABB/ Siemens/ Schneider/ Legrand/ Hagger/ L&T/ GE

Supply and fix as in repair MCB SPN/ DP 240 volts, 50 Hz capacity 63 Amps 'B' curve all as specified. Make: ABB/ Siemens/ Schneider/ Legrand/ Hagger/ L&T/ GE

Supply, installation & testing electric water storage heater (Geyser) of capacity 35 litre, vertical mounting type, (BEE Five star rated) rated power input 1000 W/2000 W/ 3000 W for Eco mode, Smart mode & Turbo mode respectively, Incoloy glass coated heating element, anode rod, suitable for 230V Single Phase 50 Hz AC supply, 0.8Mpa high working pressure withstanding capacity, IPX-4 protection, Class-I, with & including Thermostat with Thermal Cutout, heating indicator, Multi functional valve (acts as pressure release valve, non-return valve, expansion valve and vacuum release valve), fixed all as per manufacturer’s instructions, fixed with & including ‘Anchor’ type /fastener type bolts & nuts (Set of 4 bolts of 10mm dia 150mm long with nuts & washers) into the wall grouted properly to hold the geyser and making good the disturbed surface as original, complete all as specified & directed. Make Jaquar & Company Pvt Ltd/ Usha/ Ao-Smith

S & F exhaust fan of 300 mm sweep,metal body, heavy duty, double ball bearing, 1400 RPM, 70 watt, 4 blades, air delivery 1770 m3 /h, suitable for SP 230/250 Volts, 50 Hz AC supply complete with louver shutter including fixing/ grouting of frame & louvers in wall & connecting with and including 3 Nos 1.5 Sqmm single core, PVC insulated but unsheathed FRLS 1100 Volts grade cable with multistranded copper conductor from ceiling rose to fan complete all as directed. Make : Havells / Bajaj/ Crompton/Usha/Orient

S & F exhaust fan of 450 mm sweep,metal body, heavy duty, double ball bearing, 1400 RPM, 70 watt, 4 blades, air delivery 1770 m3 /h, suitable for SP 230/250 Volts, 50 Hz AC supply complete with louver shutter including fixing/ grouting of frame & louvers in wall & connecting with and including 3 Nos 1.5 Sqmm single core, PVC insulated but unsheathed FRLS 1100 Volts grade cable with multistranded copper conductor from ceiling rose to fan complete all as directed. Make : Havells / Bajaj/ Crompton/Usha/Orient

Supply and filling for dry sand in cable protection trenches before and after the cables are laid, for sand cushioning to cables complete all as specified and directed. NOTE : thickness after punning of sand shall be (minimum as specified in SSR) measured and paid in this item.

Material and labour for brick protection for UG XLPE cable with burnt clay old size sub class 'B' bricks laid dry and flat abutting each other with gaps between adjacent brick not more than 10mm and width equal to length of brick in trenches across the cable complete all as directed by Engineer-In-Charge. Make: Best quality locally available which is duly approved by GE.

Supply and laying, connecting, testing, commissioning LT UG cable XLPE Insulated,armoured, electric power cables (heavy duty) 1100 Volts grade conforming to IS 7098 with aluminium conductor multi-strand of cross-sectional area 10 Sqmm 4.00 Core laid in trenches / ducts/ inside protection pipe including cable glands, lugs and suitable size of MS saddle clips etc. also including taking out existing UG cables all as directed by Engr-In-Charge. Make: Polycab(ISI Marked)/ Finolex(ISI Marked)/ Havells (ISI Marked)/ Gloster (ISI Marked)/ KEI (ISI Marked) Note:-(a) Excavation, sand cushioning, bricks shall be measured and paid separately

Material and labour for tubes "light grade" galvanised with all fittings laid in trenches of 20 mm bore dia. Make : Tata / Jindal Steel / Prakash/ Surya Roshni ltd

Supply and fix LED bollard of 9-10 Watts, 240V, 50Hz IP 65 tripod type WITH minimum upward light component power efficient complete all as directed. Note:- (a) LM-80 certificate from NABL accredited Lab shall be submitted for LED light fittings to the Engineer-In-Charge. (b) Warranty certificate shall be submitted for LED light fitting as per standard format for minimum 50000 Hrs to the Engineer-In-Charge. (c) LED light fitting and drivers shall be of same make.

M&L for horizontal boring for 50 mm to 100mm bore GI pipe under road/pavement/hard standing at 0.6 m to 1.5 m depth from top of road level and insert 50 mm to 100 mm medium GI for Laying XLPE UG Cable with all necessary fittings and without any damage of road/pavement/hard standing surface complete all as specified and directed. Note :- (i) Necessary earth work shall be carried out and the cost for the same shall be included in the rate quoted for this item. (ii) GI pipe shall be measured and paid including this item

Supply and fix as in repairs SMC cable junction box of size 295 mm x 195 mm x 100 mm with terminals / connectors, mounting bracket & polyamide cable gland with lock nut & bolts including internal connections with proper size Copper/ Aluminum lugs/ thimbles including fixing on pole with clamps and also drilling of two holes on pole for inserting PVC insulated copper cable complete all as directed.

Bhuiya Construction (BID ID -3495887)

M/S BISWA CONSTRUCTION (BID ID -3493963)

H K Enterprise (BID ID -3502984)