SPECIAL REPAIR TO 37 SHUTTERS OF BLDG N0 P 152 P 154 P 155 P 213 P 400 P 401 P 402 P 462 P 480 P 577 P 582 AT GMS UNDER GE I GOS

Amount

Taking down rolling shutters including all hardware fittings and removing to store complete all as specified & directed.

M&L for cutting holes in brick walls/ stone walls exc one brick but not exc two brick built in cement mortor or cement lime mortor and stone walls built in lime mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed. (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F Guide channel 3" (3.50 mm thick mild steel deep channel section) complete all as specified and directed.

S&F 1 mm thick of steel rolling shutters without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, gear operated type with bevel gear box and crank handle complete all as specified and directed.

S&F Ball bearing for rolling shutters complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F Bottom plate 5" (2.25mm) for rolling shutters complete all as specified and directed.

Taking down cover hood of existing rolling shutters (gear operated/ manually size any type ) carefully and completely over hauling the shutters by applying grease and oil in bearing, springs, guide cannels, operating rods, shaft gear boxes, gear wheel etc straightening thoroughly shutter blades, guide channels anchoring rods etc and fixing back the over hood in position and ensure smooth functioning of shutters complete all as specified and directed. (Note : worn out part for replacement will be measured and paid separately.)

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F in repairs only following parts of steel rolling shutters complete all as specified and directed:- (a) MS gear box complete incl handle and anchoring rod as of approved quality

(b) Ball bearing suitable for rolling shutter

(c) Guide channel 3" (3.50 mm thick)

(d) Hood Cover made of 1 mm thick GI Sheet pattern

(e) Bottom plate 5" (2.25mm)

(f) C Class pipe 50 mm dia in shaft

(g) Anchoring rod of 25 mm dia of MS pipe

(h) Safety lever locks MS with 4 levers

(j) MS Curtains of 1 mm thick Rolling Shutter consisting of the assembly of lath sections end-locking clips and the connecting pieces at the top complete all as specified and directed.

M&L for preparation of new steel surfaces and applying two coats synthetic enamelled paint to over a coat of red oxide primer area over exc 10cm in width or girth etc complete all as specified and directed.

M&L for preparation of old decorated Steel painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Taking down cement plaster on brick or concrete surface including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed.

M&L Preparation of newly Plastered surfaces and applying three coats of white wash complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm but n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed

Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet re-inforced with MS square tube in opening as per specification and shown on drawing SSR Part-II 2020 complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement , as per specification and shown on drawing in SSR Part-II 2020 complete all as specified and directed.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 100 mm dia extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Door closer hydraulically regulated designation No 2, universal type, suitable for door shutter of weight between 36 to 60 Kg of aluminium (Die cast) body complete all as specified and directed.

S&F Powder coated Fixed/ Louered Aluminum window/ Ventilator with frame not less than 1.8 mm thick excluding aluminium grill and including 4 mm thick tinted glass, beading & necessary rubber packing, locking & opening arrangement, all fitting and fixture complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for Brick work with fly ash bricks straight or curved on plan exceeding 6 m mean radius complete built in cement mortar 1:6 complete all as specified and directed.

M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered walls surfaces making absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

M&L for applying two coats of oil bound distemper on wall or concrete surfaces on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L preparation of old painted surfaces and applying one coat of white wash on ceiling surface complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S & F 15 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

S & F 20 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

Making connection of PPR distrubution branch with PPR main of following outer dia of pipe 16 to 40mm size by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

S&F in repair PP-R globe or gate valves screwed both ends for PPR Pipes of 20 mm bore of pipe complete all as specified and directed.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in Bricks/ stone Masonary wall complete all as specified and directed.

M&L for 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Dismantling of floor, hearth, walls, roof tiles including bedding (but not backing), and rubbish off permises complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 for laying of floor tiles complete all as specified and directed.

S & F in repair Europian WC floor mounted cascade pattern vitreous china with dual core flushing cistern incl all fitting flush pipe etc complete all as specified and directed. Make-Jaquar cat SLS-WHT-0208 or equivalent of higher cost.

S&F in repair PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed.

S & F in repair Soap dish any type fixed to plug with chromoium plated brass screw complete all as specified and directed. Make-Jaquar CAN-1311 N or equivalent of higher cost.

S & F in repair Corner glass shelf with brackets complete all as specified and directed. Make-Jaquar CAN-1173 or equivalent of higher cost.

S & F in repair Double coat hook complete all as specified and directed. Make-Jaquar AQN-7761 or equivalent of higher cost.

S & F in repairs Hand shower (Health faucet) with 1 mtr long Easy flex tube in crome finish & wall hook complete all as specified and directed. Make Jaquar Cat ALD-CHR-565 or equivalent of higher cost.

S&F in repair Chromium plated angular stop cock for 15 mm bore complete all as specified and directed. Make-Jaquar CON-053KN or equivalent of higher cost.

S&F in repair Chromium plated Two-way angular stop cock for 15 mm bore complete all as specified and directed. Make-Jaquar CON-059KN or equivalent of higher cost.

S&F in repair Sink Cock with regular swinging spout (Table mounted Model) complete all as specified and directed. Make jaquar Cat FLR-5357N or equivalent of higher cost.

S&F CP Grating 75 mm dia fixed with white cement complete all as specified and directed.

S&F in repair Chromium plated Bib cock with flanges Quarter turn 15 mm bore complete all as specified and directed. Make-Jaquar FUS-29037 or equivalent of higher cost.

S & F in repair Toilet Paper Holder with Flap complete all as specified and directed. Make-Jaquar AKP-3573P or equivalent of higher cost.

S&F Chromium plated towel ring with bracket complete all as specified and directed. Make Jaquar Cat AQN -7721 or equivalent of higher cost.

S&F in repairs Stainless Steel Towel Rack 600 mm long with Lower Hangers but with 3 hooks. Make-Jaquar Cat AHS-1581 H or equivalent of higher cost.

Surface excavation n.exc 30 cm deep and getting out in soft/lose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exc 1.5m in depth; for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft/lose soil complete all as specified and directed.

M & L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L formwork to flat sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as inColumns, pillars, piers, posts and struts complete all as specified and directed

M&L formwork to Square,rectangular or polygonal rough surface of concrete of sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing surplus excavated earth (soil) to a distance n. exc 50 m & Depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Mild steel TMT bars 8mm dia and over, cut to length, spacers and binders and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L 40mm thick PCC 1:2:4 damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on brick or concrete surface, finishing even and smooth without using extra cement but using water proofing compound complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:6 on brick or concrete surface, finishing even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on concrete surface of ceiling finishing even and smooth without using extra cement complete all as specified and directed.

M&L moorum / Red bajri filling in floors or pavings, laid in layers n.exc15 cm thick spread levelled and rammed incl watering etc complete all as specified and directed.

M&L Hard core of gauge n.exc 63 mm, deposited, spread, levelled in layers not exc 15 cm thick, watered and well rammed to a true surface complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8, type D2 using 40 mm graded stone aggregate as in sub base, sub floors, including use of formwork / screed strips to divided the area in panels complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in floors finished even surface complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6, type C-1 using 20 mm graded stone aggregate as in plinth protection, surfaces finished even and smooth with out using extra cement complete all as specified and directed.

S&F glazed ceramic colored tiles (Premium quality) 200x300x6 to 7mm thick coloured on vertical surface such as dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tile including rendering 15 mm thick on brick or stone masonry surfaces finished fair and even to recieve tile in CM 1 : 4 complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , including 20mm thick screed bed in CM 1 :6 complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement based paint over a coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats colour wash over one coat of white wash complete all as specified and directed.

Supply only water proofing compound of approved make.

S&F Water closet vitreous china squatting pan, orissa pattern 580x440mm white with integral foot rests including flushing cistern and flush pipe including provision of lime concrete bedding complete all as specified and directed.

S&F vitreous china urinals, flat back of size 465mmX355mmX265mm, white with grating and union for discharge pipe complete all as specified and directed.

M&L for vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets, including supply & fixing pillar cock 15 mm bore CP fancy type, PVC connection of 450 mm long, PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as sapecified and directed.

M&L for brick work with subclass 'B' bricks straight or curved on plan to any radius half brick thick wall built in CM 1:4 complete all as specified and directed.

S&F 20mm dia GI tubing medium grade with all fittings and fixed complete to walls or ceiling or laid in floors complete all as specified and directed.

S&F 15mm dia GI tubing medium grade with all fittings and fixed complete to walls or ceiling or laid in floors complete all as specified and directed.

S&F 15 mm bore fancy type pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts complete all as specified and directed.

S&F 15 mm fancy type stop valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed.

S&F 15mm bore bib tap cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube complete all as specified and directed.

S&F 500 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 2009

S&F 25mm bore ball Brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipes or brass ferrule and fixed as in PVC Service tanks complete all as specified and directed.

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to 20mm bore GI tube complete all as specified and directed.

All as per Item No 105 above but 25 mm dia.

S&F PVC(SWR)75mm borepipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and directed.

All as per item No 107 above but 110mm bore

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR)bend 110mm bore complete all as specified and directed.

S&F PVC (SWR)bend 75mm bore complete all as specified and directed.

S&F PVC(SWR) bend 110mm bore with access door complete all as specified and directed.

All as per item No 112 above but 75mm bore

S&F PVC (SWR) vent cowl, 100mm dia complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F PTMT waste coupling of 32mm dia for wash basin/urinal complete all as specified and directed.

S&F PVC LDPE waste pipe of pressure rating 6kg/cm2 of 32mm dia pipes complete all as specified and directed.

M&L PCC 1:3:6 type C2 concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 200mm dia pipe complete all as specified and directed.

M&L 200mm dia salt galzed stoneware drain pipes laid in trenches and jointed complete all as specified and directed.

M&L cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 200 mm bore drain pipe.

S&F extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm signle core PVC insulated sheathed copper FRLS multi stranded conductor cable in and including PVC casing caping of 20 MMwith ISI marked inclusive of tees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminted 3mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sqmm FRLS cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incuding cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for following:- (a) One light point controlled by one , one way switch 5 Amp

one fan/ exhaust fan point controlled by one way switch 5 Amp

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

S&f LED lights fitting mirror lights 12W, 220V, 50 Hz complete all as specified and directed. Make: Philips cat part No 919216000000 or equivalent of higher cost.

S&F LED recess light fitting 36 watts 2x2 ft 220 volts, 50 Hz complete all as specified and directed. Make: Havells cat part No VENUSNEOHE2X2R36WLED840PIRSENSOR or equivalent of higher cost.

S&F hand dryer with automatic on/off features , low noise pollution, shockproof 230 volts, 50 Hz complete all as specified and directed. Make prestige or equivalent of higher cost.

S&F switch piano flush button single pole one way 6 Amps, complete all as specified and directed.

S&F LED bldg security light fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make Havells, Cat No enduraPearlsl25Wled757sasYtoPCmP or equivalent of higher cost.

M&L Point wiring complete with PVC insulated and unsheathed, flame retardant low smoke 1100 volt grade electric cable of 1.5 Sqmm (nominal area) with multi stranded copper conductor single core in and including rigid PVC concealed conduit not less than 19mm dia, and wall thickness 2mm, with suitable GI flush metal boxes (not less than 1.00mm thick) of suitable sizes including earth dolly with 3mm thick plastic laminated sheet top cover of approved colours including 1.50 Sqmm PVC insulated & unsheathed copper cable as continuous earth wire with all accessories including lugs required, complete all as specified and directed for the following :- (a) One light/fan point controlled by one way switch 5 Amps

(b) One 5 pin socket outlet, 5 Amps, Independent

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

M&L for Switch socket combination 2 in 1, 5 A flush type complete all as specified and directed

S&F Sheet metal enclosure factory made single door for mounting MCBs with 200A rated bus bar capacity SPN 4 way AC 230 volts with IP-43 protection, complete all as specified and directed.

S&F Ceiling rose 3 terminals of PVC/ polycarbonate, as per relevant IS code, ISI marked isolated body complete all as specified and directed.

M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less'than 1.5 meters below normal ground level, connected to galvanised iron earth lead wire of 4 mm dia GI pipe mediam grade 15 mm dia upto 7.5 mtr including provn of conrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 25x25x3 mm with lugs 02 Nos and with 6.0 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for earth plate, common sald and charcoal filing, test point made out of Bronze/ Gun metal with fixing arrangement, funnel, wire mess and excavation/ earthwork in hard/ dense soil, to a distance not exceeding 50 mtr all as per electrical plate No 3 of SSR 2009 Part I and connecting to earth test point all as specified or indicated incl testing on completion.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of 40 to 63 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning.

M&L for street light fitting bracket made out of 32mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall, painting with two coats of aluminium paint over a coat of red oxide primer complete, all as specified and directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed

Supply dry sand for cushioning to underground cables 8cm thick before laying cable and 15cm thick after lying and streching the cable, complete all as specified and directed. Note :- For payment purpose punned thickness shall be measured.

S&F sub class ‘B brick, old size, as cable protection cover, laid dry, flat, transversally along the length of cable, on sand cushioning, with width equal to the length of the brick, complete all as specified and directed

Supply, laying and testing LT cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade cross section area 10 sqmm 2 core complete laid in trenchers, duct, passing through pipe, fixed to poles complete all as specified and directed

Supply and laying for 25 mm bore 3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches of size 25 mm complete all as specified and directed

S&F PP-R Gate valves (brass insert) of 25 mm bore complete all as specified and directed

M/S SIWALIK AND CO

M/S. KISHAN ENGINEERING

M/s MAA BHAIRABI ENTERPRISES

R K Traders

M/S JAGANNATH SASMAL

HARAGOURI SUPPLIERS