WBWRIDDEEAM/BANeNIT42/NP/25-26

MATERIAL Rigid P.V.C. pipes with one loose coupler for every 6.0 mtr. Length and solvent cement accordingly to technical specification as per I.S.No. 4985/2000 with latest amendments and duly I.S.I. certification marked. 140 mm.dia Class-I (0.25 MPA) with Coupler

Rigid P.V.C. Accessories of Class-II (0.4 MPA) according to Technical specification as per relevant IS Code with latest amendment & duly I.S.I. certification marked & CIPET tested. 315 mm.dia F.T.P. with Metallic flange

160 mm.dia F.T.P. with Metallic flange

140 mm.dia 900 Bend

160 x 140 mm.dia Reducer

140 mm.dia Equal Tee

140 mm.dia End Cap

315 mm.dia Extra Coupler

200 mm.dia Extra Coupler

160 mm dia Extra Coupler

140 mm.dia Extra Coupler

MS ACESSORIES:-150 mm.dia C.I Sluice Valve (ISI Marked IS-14846)

150 mm.dia Alfa Alfa Valve (Nipple Type as per IS 210)

150 mm.dia 900 G.I Bend(Both end flanged ISI Marked IS 1239)

150 mm.dia MS Tail Piece One end Flanged other end grooved.

Nuts & Bolts :- 20 mm x 80 mm

20 mm x 100 mm

16 mm x 80 mm

For Motor driven Pump Sets (12 Nos.)

Solvent cement conforming to I.S. No. 14128/94 with latest amendments, Medium Bodies.

Rubber Insertion, duly, reinforced 5 mm.thick 2 plies as per I.S.No.-6392 with latest amendments.300 mm.dia (Table-17)

150 mm.dia (Table-17)

150 mm.dia (Table-5)

Supply of wooden pannel board of size 6ft. X 4ft. X 1 inch. with 6 Nos. M.S. clamp for Pump House wall mounting

Pump House Dismantling all types of masonry exception cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 mtrs

Dismantling of all types of plain Cement Concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor

Earthwork in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite and sand stone), including removing, spreading or stacking the spoils, within a lead of 75 m as directed.The item includes necessary trimming the sides of trenches, levelling,dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1500 mm. (considering 50 mm clearence)

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidated the same by through saturation with water ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Single brick flat soling of picked Jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Ordinary Cement concrete (Mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement , if any, in ground floor as per relevant IS codes.(a) Pakur variety

Ordinary Cement concrete (Mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement , if any, in ground floor as per relevant IS codes.(a) Pakur variety

Hire and labour charges for shuttering with centering and necessary staging upto 4 metre using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). 25 mm. to 30 mm. thick wooden shuttering. For PUMP HOUSE

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. For works in foundation, basement and upto roof of ground floor / upto 4m. Tor steel/Mild steel ( Other than SAIL/ TATA/RINL) i)For foundation Blocks of Water Distribution System

Brick work in cement mortar (1 : 6) with first class kiln burnt bricks including racking out joints, scaffolding and other incidental works etc. complete. a) In foundation & plinth.

b) In superstructure ground floor

Stripping of wornout plaste and racking out joints of walls, ceiling etc.upto any height and in any floor including removing rubbish and stacking as directed.

Plaster (to wall, floor, ceiling etc.) with (1:6) sand and cement mortar including rounding off or chamfering corners, as directedand racking out joints or roughening of concrete surface including throating. Nosing and drip course as necessary at ground floor. (a) 15 mm thick (1:6) proportion.

b) 20 mm thick with 1:6 cement mortar.

c) 10 mm thick with 1:4 cement mortar.

Neat cement punning about 1.5 mm. thick in wall dado, floor, drain, door and window sill etc. complete.

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing above 16 Kg/sq. mtr. and above

Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost of all labour and materials.

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete A) UPVC Pipes:(i) 75 mm. Dia

Earth work in filling in foundation trenches or plinth with good earth in layer not exceeding 150 mm. Including watering and ramming etc. layer by layer complete with earth obtained from excavation of foundation. (Payment to be made on the basis of measurement of finished quantity of work)

Priming one coat on timber, plastered surface with synthetic enamel/oil boud primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. Two coats (super gloss hi- gloss except white) (b) On steel surface (Normal gloss).Two coats (with any shade except white).

White washing including cleaning and smoothening surface thoroughly (5 parts of stone lime and 1 part of shell lime should be used in finishing coat) all floor b) Three coats

Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification. ii) b) Two coats

Supplying, fitting and fixing including transportation of sign board for identifing the exact location of Major RLI scheme ( one at rode side and other at site) the board will be made 3 mm thick MS plate of 300 mm X 600 mm and fitted and fixed on 50 mm GI Pipe of IS 1239/90 (part-I) including cutting, welding and writting of both sides of Sign board. Base - Yellow, and ward - Red. Both bottom end of the stands pipe will be grouted in 1:2:4 CC on a single brick flat soilng. This will include one materials and labour complite as per drawing and direction of EIC.

Carriage on (SL No.-18 to 49) except Item No-27 & 44 ( 4%)

WATER TRANSMISSION ARRANGEMENT Installation/Erection of Surge Tank/Shore manifold( to be supplied from Deptt. free of cost) over a rigid base of ordinary cement concrete (1:2:4) with graded stone chips (20 mm nominal size) of pakur varity of 1250mm X 1250mm X 150 mm over a single layer of brick flat soling and embedding the legs of surge tank/shore manifold with in the concrete base including cost of all materials and labour charges and as per direction of Engineer-in-Charge.

Dismantling all types of masonry exception cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 mtrs.)

Dismantling of all types of plain Cement Concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor

Earthwork in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite and sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, leveling, dressing and ramming the bottoms, bailing or pumping out of water etc. as required complete.

Labour charge for fitting fixing 150 mm Dia Alfa Alfa valve with 160 mm dia P.V.C riser pipe with the help of flanged P.V.C tail Piece by joining the P.V.C end of Tail Piece and riser Pipe with coupler and flanged end of tail piece and Alfa Alfa valve with rubber insertion, nuts and bolts, complete.

Laying of P.v.C. pipes of different diameters within field trenches in curve /straight line using P.V.C. fittings, viz. Bend, Tee, Reducer etc. and making leak proof joints with couplers after roughening the surface with wire brush and emery paper and applying solvent cement (The rate is inclusive of transport of pipes, fittings and solvent cement to be supplied by Deptt.) all complete as per direction of Engineer-in-Charge c) 140 mm dia

Labour charge for replacement of damage P.V.C Pipe of any length in the pipe line of HDTW/MDTW/RLI with new piece of pipe after taking out damage pipes from the existing pipe line by cutting hacksaw and joining the new pipes with the existing pipe line using necessary couoplers after oughening up surface with wire brush,emery paper and applying the solvent cement (cost inclusive) to make the joint leakproof (pipe coupler to be supplied departmentally) including transpoting departmentally issued pipes coupler etc. from Sub-Divisional store to the site all complete as per direction of Engineering-in-charge. i) 315 mm dia. PVC Pipe

ii) 200 mm dia. PVC Pipe

iv) 140 mm dia. PVC Pipe

Repair of puncture/holes of any size in existing P.V.C. pipeline of HDTW/MDTW/RLI by placing half round P.V.C. pipe section of required size to cover the Holes/puncture having adequate bearing on all sides and joining the half round section with solvent cement after roughening the surface with wirw brush ,emery paper to make the joint leak proof as per direction of engineer -in-charge (cost inclusive of supplying sovent cement at site and transportation of required length of P.V.C. pipe to be issued departmentally ,for cutting half round section, from Sub-Divisional stores to site) ii) 200 mm dia. PVC Pipe

iii)140 mm dia PVC pipe

Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by through saturation with water ramming complete including the cost of supply of sand. (Payment to be made on measurment of finished quantity)

Brick work with 1st Class bricks in cement mortar (1:4) in foundation and plinth

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

Ordinary Cement concrete (Mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement , if any, in ground floor as per relevant IS codes.(a) Pakur vareit

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (c) 15 mm thick plaster. .

Neat cement punning about 1.5 mm. thick in wall dado, floor, drain, door and window sill etc. Complete..

)Fitting and fixing of M.S. / G.I. / C.I. accessories and special in pipe line (accessories & special to be supplied departmentally) including supply of jointing materials viz. rubber insertion, nuts & bolts, havoc Zink (Zink Oxide) complete as per direction of Engineer-in-Charge 150 mm dia. Sluice valve

150 mm dia. and 315 mm dia. E.R.W Pipe 90° Bend

150 mm dia suction hose with clamps and foot valve

Labour charge for fitting fixing 150 mm Dia Alfa Alfa valve with 160 mm dia P.V.C riser pipe with the help of flanged P.V.C tail Piece by joining the P.V.C end of Tail Piece and riser Pipe with coupler and flanged end of tail piece and Alfa Alfa valve with rubber insertion, nuts and bolts, complete.

Welding in M.S. structural work with gas or electric:(b) Continuous weld.

Earth work in filling in foundation trenches or plinth with good earth in layer not exceeding 15cm. Including watering and ramming etc. layer by layer complete with earth obtained from excavation of foundation.

Testing of pipe line system against leakages by filling the distribution chamber with water and supplying water through the entirepipe line net work for at least 4 (four) hour by running the departmental Deasel Engine pumping set, including supplying necessary fuels & lubricants and hiring and transporting tools and plants all complete as per direction of Engineer-in-Charge. (As it is electrified scheme so testing can be done with Electro Motor Pumping set & the departmental electric line)

Carriage charge (4%) on every item from Sl. no-51 to 74 excluding Sl. No-54 & 73,74

Transportation of Diesel Engine pumping set / Electro-Motor pumping set for Major R.L.I. of any make/brand with necessary fixtures viz. M.S. bend, M.S. Pipes, Rubber Hose Pipe, Manifold, Surge tank, foot valve, non-return valve, tail piece, hose clamp, sluice valve, priming chamber etc. over Pucca/Kancha road from Sub-Divisional Store to worksite excluding loading at the lifting point and unloading at the delivery point. (a) Distance upto 50 km.

Installation of Diesel Engine /Electro-Motor pumping set of any make / brand and for RLI scheme on pump foundation over SAL sleeper (to be supplied departmentally) by fixing nuts and bolts and making connection of suction hose and foot valve with necessary fittings at the inlet end of the water pump and fitting fixing of 90° M S priming bend, sluice valve and delivery hose with all necessary fittings at the delivery end of the water pump, duly connected with the pipe line, maintaining proper alignment and level including cutting holes on the wall of the pump house where necessary, mending good damages after completion of the works as per direction of Engineer-in-charge. (Pump set and all accessories will be supplied departmentally).

INTERNAL WIRING Fitting of wooden pannel board of size 6ft. X 4ft. X 1 inch. with M.S. clamp on the wall of pump house and made necessary arrangment for fitting fixing the following elctrical equipment including 2 coat of pantigof app.quality as per direction of E.I.C.

Fixing only Sheet Steel Main Switch(Rewirwable type)/ Change over on Flat Iron Frame/Angle Iron Frame on wall 63 Amps On angle iron frame

Fixing only Sheet Steel Main Switch(Rewirwable type)/ Change over on Flat Iron Frame/Angle Iron Frame on wall 200 Amps On angle iron frame

Fitting & fixing of Starter (Direct on Line or Star-Delta/Auto- Transformer) with Nuts & Bolts fixed on Angle iron frame on wall and making necessary connection with the electrical cables. iii) Star-Delta / Auto-Transformer Starter (Above 15 HP upto 25 HP)

Fixing only MS sheet metal busbar Chamber on angle iron frame on wall. 4 bars, 200 Amps.

Supplying and Drawing with 1.1 KV, PVC flexible 'FR' cables copper conductor conforming to IS 694 in suitable size with fitting and fixing on wall/Kiosk Box , including making necessary connection to the pre-fixed devices with all necessary accessories like saddle, screw, clips, gland, socket etc. conforming to IEE regulation and as per direction of EIC. (Brand: Gloster/Havells/Finolex) (i) 4Cx 25 sqmm Copper cable conforming to IS 694 in [ 100/200 A TPN switch to Bus-bar]

(ii) 3C X 16 sqmm copper cable conforming to IS 694 [Busbar to 63 A, TP Main switch and 63 A TP switch to Motor starter]

(iii) 2 X 3C X 10 sqmm copper cable conforming to IS 694 in 32 mm GI conduit (ISI-Medium quality) [ Star-Delta Motor starter to Motor]

Supplying & fixing bulk head light fitting(Havells Make) on wall / Ceilling incl. S&F suitable 100 watts lamp complete with glass wire-guard and holder.

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in suitable size PVC casing-capping (Precision make) with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, incl. necy. fittings etc. to light/fan/call bell point with Modular type switch (Brand approved by EIC) fixed on Modular GI / PVC switch board with top cover plate on wall incl. mending good damages to original finish. [PVC casing capping and Switch board both on surface] (a) Average run 5 mtr

Connecting the equipments to earth busbar including S & F G (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages (a) Solid GI wire (iii) No. 8 SWG

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By TATA-Medium GI pipe

Supply & Fixing EI danger board on wall 20cm x 30cm ( 8" x 12" )

Insulation testing of internal wiring of Pump House/Kiosk Box including wiring of electric Motor & other ancilary equipments by means of Megger

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required

Add GST @18% for the item No (25 to 92) on 437988.68

cess 1% on for the item No (25 to 92) on 516826.64

Please Enable Macros to View BoQ information