Setting up of state of Art Plug paly IG1

Amount

PLAIN WORK STATION SIZE 1200MM(L)X600MM(B)X750MM(HT) Providing, fabricating and fixing in position Panel based modular workstations which Includes Partition, work surface, pedestal & MS powder coated CPU trolley. Work surface & gable ends will be in in 25mm thick exterior grade prelaminated Particle board with 2mm thk PVC imported edge banding tape for tops & 0.8mm thk PVC imported edge binding tape for verticals. The bottom surface of the table shall also be laminated. The worktops will be supported by MS powder coated brackets at regular intervals. The worktops shall be provided with PVC wire manager for cabling. Partition thickness will be 60mm with the inside gap between two tiles will be approximately 50mm for higher wire carrying capacity Frame Horizontals will be of Imm thick CRCA sheets & the verticals will be of Aluminium Extrusions of 1.5mm thick. All the frames will be duly powder coated based which will be inline with the Top trims & end trims. The partitions will be provided with leveling bolts/screws to take care of undulations in the floor level. Tiles: The fabric tile panels will be Constructed out of 4mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. One of the tile panel will be Whiteboard marker tiles made out of 4mm MDF with Imm glossy face laminate with a balancing laminate on the back. And one of the tile panels will be Magnetic tile Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Wire management: Internal Concealed raceways to be provided below work surface with switchboard arrangement for Power & Data along with PVC Wire manager with Grommet / scallops & Individual raceway arrangement for Data/ Power cable, Drawer Pedestal:- The Pedestal Unit of Dimensions 400W x 470D x 675mmH will be made of 18mm thick pre laminated particle board. All the exposed edges will be sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top ard drawer fascia will be sealed with 2mm thick PVC edge. This includes the site inspection & site survey, detail design & shop drawing for final review to issue as Good for Construction as per the approved Specifications. The drawer unit will consist of 2 box drawer and 1 file drawer. The sides of Inside drawer box will be of prelam particle board. The drawer box will be fitted with roller Slide for free movement. The drawer unit is provided with central locking system, where in the three drawer will be locked with one key.PVC recessed handles will be provided. The drawer unit will be fitted on castors. CPU Trolley & Keyboard tray:- CPU trolley will be made from Imm Thick CRCA steel sheet. The trolley will be mounted on lockable castors. The keyboard tray will be MS powder coated & will be fixed on telescopic channels & have provision for mouse pad. All material shall be of approved make. All works complete as per the drawing/ Image, technical specification and direction of the Engineer.

EXECUTIVE TABLE FOR CHAIRMAN AND MANAGING DIRECTOR SIZE:1800mm(L)X900mm(D)X750mm(H) & (SIDE TABLE SIZE: 1500 mm(L)X450mm(W)X700mm(H) Supplying and installing in position main table of approved make, colour and size 2400mm(L)X900mm(W)X750mm(H) with a curved top made up of 25 mm thick exterior grade prelaminated Particle board with 2mm thk PVC imported edge banding tape for tops & 0.8mm thk PVC imported edge binding tape for verticals. The bottom surface of the table shall also be laminated. The worktops will be supported by MS powder coated brackets at regular intervals. The worktops shall be provided with PVC wire manager for cabling. Partition thickness will be 60mm with the inside gap between two tiles will be approximately 50mm for higher wire carrying capacity. Frame Horizontals will be of Imm thick CRCA sheets & the verticals will be of Aluminium Extrusions of 1.5mm thick. All the frames will be duly powder coated based which will be inline with the Top trims & end trims. The partitions will be provided with leveling bolts / screws to take care of undulations in the floor level. The pedestal unit of size 350mm(L)X450mm(W)X550mm(H) with top made up of 25 mm thick prelaminated particle board with post formed edge profile & sides in 18 mm thick prelaminated particle board and 75 mm height skirting with 2mm thick PVC edge banding & sealed edges in 0.8 mm thick PVC edge banding. The pedestal will have three equal size drawers with front fascia having central locking system & full length aluminium G profile handles/ 4"SS 304 grade brush finish handles,roller slide mechanism and casters for added mobility All material shall be of approved make. All works complete as per the drawing/Image, technical specification and direction of the Engineer.

CORNER TABLE (T21) (SIZE:600mm(L)X600mm(D)X450mm(HT) Providing & installing in position wooden side table made of size 600mm(L)X600mm(D)X450mm(HT) teak wood of square shape with wooden legs in horizontal & vertical frame of size 50x50mm and 10 mm thick plain glass on top fixed in 10 mm groove made in horizontal wooden members. The table shall include necessary hardware fittings, fixtures etc. The table will be finished with 3 coats of melamine polish of approved colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer.

RECEPTION TABLE (B1) (Main Table of Size 1500 mm(L) x 600mm(W) x1140mm(HT) & Side Table of Size - 1200 mm (L) x 450 mm (W) X 700 mm (H) Providing & fixing in position Reception table in 19 mm thick Marine BWP (boiling water proof) plywood with 50mm thk ledge box finished with corian make acrylic surface on the outside and 1 mm laminate inside , ms powder coat coated keyboard trays with accommodation of mouse pad and 2 nos of fixed drawer units with 3 no of drawers each made up of 19 mm thick plywood front fascia, 12 mm ply for sides and back, with 6 mm ply for base, side supports to be run on telescopic side mounted channels including central locking arrangement, heavy duty brushed stainless steel 'D' handle (4"), all exposed edges to be finished with teak wood lipping with 3 coats or more of melamine polish to match the shade of laminate with necessary labour, Provision shall be made for wire management to take care of basic wiring requirement for providing power data- voice switches on a modular switch plate. Table switches have independent wire manager and MS powder coated CPU trolley of standard size, S.S 304 grade hardware, cleaning, placing in position, etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

BACK STORAGE UNIT FOR RECEPTIONIST (SIZE:1500 mm(L)X425mm(D)X750mm(H) Supplying and installing in position back storage of approved make, colour and size with top made up of 25 mm thick prelaminated particle board to be extended in one piece as specified & having storage body made up of 18mm thick exterior grade pre laminated particle board, back of the unit made up of 9 mm thick particle board with 75 mm height skirting. All the exposed edges are in 2 mm thick PVC edge banding & sealed edges are in 0.8 mm thick PVC edge banding. Two equal size shutters fixed with s.s. brush finish brass hinges & full length aluminium G profile handles / 4" s.s 304 grade brush finish handles, premium lock to be provided and one shelf in centre fixed on shelf button. Both made up of 18 mm thick prelam particle board with 2 mm thick PVC edge banding on exposed sides & sealed edges in 0.8mm thick PVC edge banding. All material shall be of approved make. All complete as per the drawing / Image, technical specification and direction of the Engineer.

SOFA Supplying & placing in position sofa having solid frame structure with inner frame made of kiln chemical treated approved high quality wood. The seat cusion to be made of 7" multi layered foam of density 32D and HD with polyester polyfill outer layer of 180 gsm to keep the upholstery wrinkle free & soft. The thread used to be nylon bonded to provide lasting stitch strength. The backrest to be made of 3 inch foam of 23D with polyester polyfill outer layer of 180 gsm to keep the upholstery wrinkle free & soft. The seating cushions to have 2 inches of elastic webbing of 250 gsm with diagonal weave. The thread used to be nylon bonded to provide lasting stitch strength. The outer finish to be of superior quality leatherette stictched with nylon bonded thread. The legs to be of s.s 304 grade tubular section of dia 75mm and 2 mm thickness with rubber gasket. All material shall be of approved make. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Seat Height - 410 mm)

3 SEATER SOFA

SINGLE SEATER SOFA

CENTER TABLE

EXECUTIVE CHAIRS EXECUTIVE CHAIRS FOR DIRECTORS & THE CHAIRMAN (C1) Supplying and placing in position armed revolving high back chairs of approved make and colour, BIFMA (The Business & Institutional furniture manufactures association) compliant and having features like knee tilt syncronous mechanism with 4 position locking & anti shock feature & 2way adjustable lumbar support.PU coated adjustable Armrests with 4 position height & width adjustment & adjustable head rest, The back to have mesh fabric & leatherite for Seat. Die Cast Aluminium Base with PU Castors as per approved image and make etc. Rate shall include of all iron mongeries hardware, fittings, fixtures etc. All material shall be of approved make. All works complete as per the drawing/ Image, technical specification and direction of the Engineer.

STAFF CHAIRS Supplying and placing in position armed revolving medium back chair of approved make and colour with HR (high-resilience) foam seat and back BIFMA (The Business & Institutional furniture manufactures association) compliant and having features like knee tilt syncronous mechanism with 4 position locking & anti shock feature. PU adjustable Armrests, nylon base with PU castors. The back and seat upholstered in fabric. Rate shall include of all iron mongeries hardware, fittings, fixtures etc. All material shall be of approved make. All works complete as per the drawing/ Image, technical specification and direction of the Engineer.

LOW HEIGHT STORAGE CABINET (SIZE:900 mm(L) x400mm(D)x750mm(HT) Supplying and installing in position storage cabinet of approved make, colour and size 900mm (L) X400mm(W) X750mm(HT) top made up from 25mm thick exterior grade pre laminated particle board. The back of the unit is made from 9mm prelaminated particle board. All the exposed edges are to be with 2mm PVC edge banding and sealed edges are with 0.8mm thick PVC edge banding and with equal size shutters fixed with s.s. brush finish brass hinges & full length aluminium G profile handles / 4" s.s 304 grade brush finish handles, premium lock to be provided and one shelf in centre fixed on shelf button. Both made up of 18 mm thick prelam particle board with 2 mm thick PVC edge banding on exposed sides & sealed edges in 0.8mm thick PVC edge banding.. All material shall be of approved make. All works complete as per the drawing/Image, technical specification and direction of the Engineer.

OVERHEAD STORAGE CABINET (SIZE:1500mm(L) x 400mm(D)x 1250 mm(HT) behind Receptionist & size: 3000mm(L) x 400mm(D)x 1250 mm (HT) in Kitchen. Supplying and installing in position storage cabinet of approved make, colour and size stated with top made up from 25mm thick exterior grade pre laminated particle board. The back of the unit is made from 9mm prelaminated particle board. All the exposed edges are to be with 2mm PVC edge banding and sealed edges are with 0.8mm thick PVC edge banding and with equal size shutters fixed with s.s. brush finish brass hinges & full length aluminium G profile handles / 4" s.s 304 grade brush finish handles, premium lock to be provided and one shelf in centre fixed on shelf button. Both made up of 18 mm thick prelam particle board with 2 mm thick PVC edge banding on exposed sides & sealed edges in 0.8mm thick PVC edge banding.. All material shall be of approved make. All works complete as per the drawing/ Image, technical specification and direction of the Engineer.

File Storage:- Supplying and installing in position storage in 19 mm thick Marine BWP (boiling water proof) plywood with shutters in 19mm thick BWP (boiling water proof) plywood fixed on SS. brush finished brass 'L' hinges & 100 mm height SS 304 grade handles. The cabinet to have 19mm thick plywood shelves fixed on shelf buttons, back sheet in 8mm plywood & finished with 1mm thick laminate externally and 0.8mm thick laminate internally. All exposed edges to be finished with teak wood lipping with 3 coats or more of melamine polish to match the shade of laminate & with necessary labour, S.S brush finish hardware, cleaning, placing in position etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer. (Size 3000mm x450mm x3000mm (HT) in Pantry cum store room) & (Size 1600 mm x450mm x3000mm (HT) in store room next to wash area.

GRID FALSE CEILING Providing and fixing of PVC coated Gypsum tile Suspended Ceiling System using pre coated (Exposed portion only) GI T Grid system in 600x600mm module which includes providing and fixing wall angle along the perimeter of the room with help of nylon sleeves and wooden screws at 300mm centers & then suspending the main tee from the soffit with help of soffit cleat, rawl plugs and wire rod with leveling spring clip at 1200mm c/c. 1200mm Cross Tee shall be interlocked into the pre-cut slots in the main Tees at 600mm centers in direction perpendicular to the main Tee to make a grid of 600x1200mm. 600mm Cross tees shall be interlocked into the pre cut slots in the 1200mm tees at 1200mm centers and in direction parallel to the main tee. Cross Tees having length more than 600mm shall be supported independently. The tile shall be of size 595x595mm & 9mm thick, square edge with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film. The tile shall have light reflectance > 75%, humidity resistance of 90% and thermal conductivity of 0.24 W/m°K. The gypsum tile shall be placed into the grid size of 600x600mm. The item also includes providing cutouts for electrical fixtures etc. Marking has to be provided for Sprinkler, Smoke Detectors etc. on the ceiling and also templates have to be provided and fixed in the ceiling made of 12mm BWR (boiling water proof) Plywood. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

VERTICAL BLINDS Providing & fixing in position vertical blinds 100 mm wide approved fabric and of approved make, colour with head rail of 25mm height and 47mm wide extruded high strength anodised aluminium alloy section. End control unit state of art reduction ratio of 3:5:1 for a very smooth operation of the blind. It shall include all necessary fittings and fixtures like tilt rod, tilter chain, carrier/ runner, spacers, installation bracket, cord weight, cord, bottom mechanism consisting of weight and chain etc. complete. All material shall be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer

CAFETERIA TABLE (T18) (SIZE:1200mm(L) X750mm(D) x750mm(HT

PARTLY GLASS PANELLED & PARTLY SOLID PARTITION WITH LAMINATE FINISH AND GLASS DOOR Providing & fixing in position, full height partly glass panelled & partly solid partition made of treated salwood framework of size 38mm x 50mm having grid spacing at 600mmx600mm centre to centre both ways & covered with 12 mm thick Marine BWP (boiling water proof) plywood on both sides of framework & finished with 1mm thick laminate of approved color and texture. The framework shall be properly screwed to the walls, ceiling and floor and plywood shall be screwed to the framework. The space between the framework grid shall be filled with glass wool for sound insulation. The partition will have an opening as per the height specified in the drawing. Glass of thickness 12 mm will be fixed in the opening with wooden beading of size 38mm x 12 mm on both sides. Wooden beadings will be finished in three or more coats of melamine polish (glossy/matt) including final coat of buffing till the required finish is achieved. All hidden framework to be painted with black japan paint. Glass door shall be made using 12 mm thick toughened glass with 100 mm high plywood frame with laminate finish, fixed using double action floor spring, top patch, bottom pivot in SS brush finish and s.s. 304 grade handles of size 200mm. Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

FULLY GLASS PANELLED PARTITION AND GLASS DOOR Providing & fixing full height glazed partition upto 2400 mm height with 12 mm thk toughened glass, 35x12mm thick teak wood beading on all sides, The beading shall be finished with three or more coats of melamine polish (glossy/matt) including final coat of buffing till the required finish is achieved Solid sandwich partition above lintel level & upto slab bottom using 38 X 50mm treated Salwood frame having grid spacing at 600mm centre to centre both ways & sandwiched by 8 mm thk plywood & 12 mm gypsum on both sides. All hidden framework to be painted with black japan paint. 100mm in height plywood skirting to be finished with 1 mm thk laminate of approved make/color/ sample on both the sides. Glass door shall be made using 12 mm thick toughened glass with 100 mm high plywood frame with laminate finish, fixed using double action floor spring, top patch, bottom pivot in SS brush finish and s.s. 304 grade handles of size 200mm. Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon: Second class Indian teak wood.

Providing and fixing 50 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary screws: Second class Indian teak wood

Melamine polishing on wood work (one or more coat): Glossy

SINGLE SHUTTER DOOR WITH VISION PANEL IN PARTITION Providing & fixing in position frameless factory made solid core waterproof flush door shutter of 35 mm thick & finished with 1mm thick laminate of approved colour & texture on both sides & teak wood lipping of size 37x12mm on edges of shutter. The shutter shall be provided with a vision panel of size 275x600mm using glass of 8 mm thickness fixed with teak wood beading of size 19x12mm on both sides. The door shail be fixed on SS. brush finished brass butt hinges & provided with a surface mounted hydraulic door closer, SS matt finish concealed mortise lock case with lever handle, profile thumb turn cylinder (with key outside & thumb turn inside) with key hole, PVC door buffer & SS brush finish door stopper. All exposed teak wood lipping shall be finished with 3 coats or more of melamine polish (Matt/Gloss) to match the colour/ shade of the laminate including final coat of buffing till the required finish is achieved. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.(Refer drawing number - IN - 610). a) SIZE - 900 mm (L) X 2400 mm (HT)

SINGLE SHUTTER DOOR WITH VISION PANEL IN PARTITION Providing & fixing in position frameless factory made solid core waterproof flush door shutter of 35 mm thick & finished with 1mm thick laminate of approved colour & texture on both sides & teak wood lipping of size 37x12mm on edges of shutter. The shutter shall be provided with a vision panel of size 275x600mm using glass of 8 mm thickness fixed with teak wood beading of size 19x12mm on both sides. The door shail be fixed on SS. brush finished brass butt hinges & provided with a surface mounted hydraulic door closer, SS matt finish concealed mortise lock case with lever handle, profile thumb turn cylinder (with key outside & thumb turn inside) with key hole, PVC door buffer & SS brush finish door stopper. All exposed teak wood lipping shall be finished with 3 coats or more of melamine polish (Matt/Gloss) to match the colour/ shade of the laminate including final coat of buffing till the required finish is achieved. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.(Refer drawing number - IN - 610). b) SIZE - 1200 mm (L) X 2400 mm (HT)

MAIN ENTRANCE DOOR (Size- 2115mm(L ) x 2400mm(HT) Providing and fixing main door using 12mm thick toughened glass. The door shall have two shutters fixed on stainless steel patch fittings at top and bottom with double action stainless floor spring at bottom corner and both shutters shall have stainless steel lock at floor level. Plywood architrave/ frame using 19mm+19mm +12mm Marine BWP (boiling water proof) plywood shall be fixed on three sides and finished with Imm thick laminate. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer

DISCUSSION TABLE (T10) (SIZE: 1200mm dia X 750mm(HT) Supplying and installing in position Discussion table of approved make, colour and size 1200mm dia with top made up of 25 mm thick exterior grade prelaminated board and having superior edge profile with 2mm thick PVC edge banding of matching colour. The understructure of the table is made up of stainless steel 304 grade plate & a vertical support tube of stainless steel 304 grade 90mm diameter. The base to be circular at the bottom and top. The top base to have required holes for fixing table top to it. All material shall be of approved make. All works complete as per the drawing/ Image, technical specification and direction of the Engineer.

UPS AND BATTERY STORAGE (B20) (Size- 1800mm(L) x 600mm(W) x750mm(HT) Providing & fixing in position UPS Storage in 19 mm thick Marine BWP (boiling water proof) plywood with 25 mm thickness louvered sandwich shutters in 12mm thick BWP (boiling water proof) plywood framework with 6mm thick BWP (boiling water proof) plywood on both sides fixed on SS. brush finished brass 'L' hinges & 100 mm height SS 304 grade handles and having the louvers in 38x12mm thick wooden lipping. The cabinet to have 19mm thick plywood shelf fixed in center on shelf button, back sheet in 8mm plywood & finished with Imm thick laminate externally and 0.8mm thick laminate internally. All exposed edges to be finished with teak wood lipping with 3 coats or more of melamine polish to match the shade of laminate & with necessary labour, S.S brush finish hardware, cleaning, placing in position etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

KITCHEN COUNTER SHUTTERS Providing & fixing counter shutters in kitchen in 19 mm Marine BWP (boiling water proof) plywood, Imm thick laminate externally and 0.8 mm laminate internally. Frame for fixing shutters to be 19 mm ply with 0.8 mm laminate finish, all edges to be finished in Teak wood lipping patti with 3 or more coats of melamine polish to match the shade of laminate. SS. brush finished brass 'L' hinges and G-profile aluminium handles to be used as per design. All the materials shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

PANELLING IN DIRECTOR'S AND CHAIRMAN'S ROOM (Size- 1800mm(L) x 2800mm(HT) Providing & fixing panelling with 19 mm Marine BWP (boiling water proof) plywood framing at approx 600 centre to centre. 12 mm ply fascia. finished with 6mm back-painted glass pasted with silicon sealant. Also providing recessed LED strip lights on both sides of approved colour with choke and accessories. Cost to include required wire management. All the materials shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

MIRROR (Size- 900mm(L) x1200mm(HT) Providing & fixing in position 6mm thickness Mirror on wall using 304 grade S.S studs with crystal polished edges with required accessories. The mirror shall have holes of suitable diameter for fixing SS. studs, with necessary hardware, labour, fixing in position etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

ACOUSTICAL GRID FALSE CEILING Providing & Fixing of Mineral Fiber Acoustical Suspended Ceiling System using Microlook edge Tiles with 15 mm exposed grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.90, Light Reflectance >88%, Thermal Conductivity k = 0.032 w/m K, Colour White & black, Fire Performance Class 0/ Class 1 (BS476 Class 6&7) in module size of 600 X 600 X 15 mm /20 mm, suitable for Green Building application, with Recycled content of 88% (FG). The grid should be of approved make with 15mm wide T-section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm and a load carrying capacity of 23.71 Kgs/M2. The T Sections should have a Galvanizing of 120 grams/sqm & passed through 500 hrs of Salt test. The Tile & Grid system used together should carry a 15 year warrantee. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum center. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm center to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers. SUSPENSION SYSTEM: Should consist of M6 Anchor Fasteners with Vertical Hangers made of Galvanized steel of size 26 x 26 x 25 x 1.2mm with a Galvanized Thickness of 80gsm, a pre Straightened Hanger wire of dia 2.68 mm of 1.83 m length., thickness of 80gsm and a tensile strength of 344-413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanized spring steel for 2.68 mm with a minimum strength of 110 kg. The adjustable clip should consist of a 3.5 mm aquiline wire to be used with the main runner. All material should be of approved make. All complete as per the drawing, specification and direction of the Engineer.

PIN-UP BOARDS (SOFT BOARDS) Supply and installing in position soft display board having aluminum frame including 12mm thick soft board with blazer cloth top fixed in frame with clip fitting with all stainless steel hardwares and easy fixing to the wall. All material shall be of approved make. All works complete as per the drawing / Image, specification and direction of the Engineer. a) SIZE-1000mm (L) X 350mm (HT)

PIN-UP BOARDS (SOFT BOARDS) Supply and installing in position soft display board having aluminum frame including 12mm thick soft board with blazer cloth top fixed in frame with clip fitting with all stainless steel hardwares and easy fixing to the wall. All material shall be of approved make. All works complete as per the drawing / Image, specification and direction of the Engineer. b) SIZE- 900mm (L) X 600mm (HT)

NOTICE BOARD (SIZE: 1200mm (L) x 900mm (HT) Providing and fixing in position Notice board of size 1200mm(L) X 900(HT) mm made of Aluminium frame with Acrylic shutter including 12mm thick soft board with blazer cloth top fixed in frame with clip fitting with all stainless steel hardwares such as screws, locking arrangement etc. and making arrangement for fixing on wall all complete as per design. All material shall be of approved make. All works complete as per the drawing./ Image, specification and direction of the Engineer.

MAGNETIC WHITE MARKER BOARD (SIZE: 2400mm(L) x 1200mm(HT) Providing and fixing in position approved Magnetic white matt finish marker board of (SIZE - 2400 X 1200 )having Moulded Anodized Aluminium frame & stain resistant porcelain coated 28 gauge steel backing with Virgin ABS (Acryloniprile Butadiene Styrene) Molded 300x100mmm Chalk tray and Eraser complete, including all accessories. All material shall be of approved make. All works complete as per the drawing./Image, specification and direction of the Engineer.

GREEN CHALK BOARD (SIZE: 2400mm(L) x 1200mm(HT) Providing and fixing in position non magnetic green chalk board of Ceramic steel sheet matt finish in green colour including Anodized Aluminium frame Virgin ABS (Acryloniprile Butadiene Styrene) Moulded 300x100mm chalk tray & Eraser, Including all accessories complete. All the materials shall be of approved make. All works complete as per the drawing./ Image, specification and direction of the Engineer.

FROSTED FILM FOR CABIN GLASSES Providing and fixing frosted Glass film partly opaque partly translucent on glass internal partitions and doors as per approved sample,design, drawing, specifications & direction of the Engineer with necessary glue, if required, labour, fixing in position etc.complete..All the materials shall be of approved make.

STAINLESS STEEL DUST BIN (300mm dia x 650mm ht) Providing and placing in position 16 gauge pedal stainless steel dust bin of grade 304 cylindrical with cover (300mm dia x 650mm ht). All material shall be of approved make. All complete as per the drawing, specification and direction of the Engineer.

TEXTURE PAINT Providing and applying Texture paint of approved color and texture. Before applying texture paint, surface smoothness has to be checked properly and base should be well prepared and non absorbent. All the materials shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

Providing and fixing vinyl plank flooring of approved make and approved colour with thickness not less than 4mm on the existing mosaic tiled flooring with adhesives, etc complete as per the specification and to the satisfaction of the Engineer - In - Charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 mts. lead.

Dismantling old ceiling plaster or raking out joints and cleaning the ceiling surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm.

Dismantling of flushing cistern,taps, urinals, wash basins, WC & like of any inculding stacking of useful materials near the site.

Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete and staking within 50 mt. Lead. Of area 3 sq.m. and below

Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete and staking within 50 mt. Lead. Area beyond 3 sq.m.

Dismantling steelwork in single sections in channels, angles, tees and flats including dismembering and stacking within 50 mts. Lead.

Dismantling steelwork in built up sections in angles, tees, flats and channels including all gusset plates bolts, nuts, cutting dismembering and staking within 50 mts. Lead

Dismantling G.I. sheets roofing including ridges, hips valleys and gutters etc. and stacking the material within 50 meters lead.

Disposal of debris, building rubbish, undesired material, unserviceable earth to the Contractor's identified dumping location upto 10km including all leads, lifts, required statutory approvals and all costs. (Contractor shall identify the location and take all required Approval to indemnify PMC & Employer)

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm : Jet Black

Wood Finish Wood Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wooden styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) and printed matt having wooden textures used along with UV Resistant resin to give the clear texture on the door. The core of shutter will be filled with MR 2nd grade Block Board. The Shutter to be water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (RV Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001-2015 certified factory. Accessories: i) S.S. Hinges 4" - 3 Nos ii) S.S. Latch - 1 No iii) Tower Bolt 5" - 2 Nos iv) Handle 5" - 2 Nos Shutter Thickness : a) 32 mm Note: For 35 & 40mm thickness shutters, only frames of 5 x 2½ Cross section frames to be used.

FRP (Fiber Reinforced Polymer) Frames with Wood Finish Manufacture, Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001-2015 certified company. Specified Cross Section : c) 4" x 2 and 1/2 "

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with two sliding shutters using 18 mm series shutters section.

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with three sliding shutters using 18 mm series shutters section

Supply and installation of Aluminium Louvers. The frame should be made of Aluminium tubes of size Item 100x50X1.50 mm thk and 50X25x1.50 mm thk C channels. Aluminium Z shaped louvers of 100mm should 8052 be fixed to the supporting frame with aluminium cleats, GI screws, etc complete. The whole assembly is powder coated with pure polyester paint. (MS framing to be paid separately)

Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section.

Providing flat iron hold fast 40 cm including fixing to frame with 10 mm Dia bolts, nuts and wooden plugs and embedded in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 stone aggregate 20 mm nominal size. (b) 40 x 3 mm flat iron hold fast, 40 cm long

Provided and fixing 150 mm chromium plated brass floor door stopper with rubber cushion screws etc. to suit shutters thickness complete.

Providing and fixing brass hydraulic door closer of make Everest universal 68 or equivalent with necessary screws and fittings complete.

Providing and fixing bright finished brass handles with necessary screws etc complete 150 mm

Providing & fixing chromium plated brass tower bolts (barrel type) with necessary screws complete. 250 x 10 mm

Provided and fixing chromium plated brass 100-mm. rim latch and lock and a pair of knobs with necessary screws etc. complete (Indian make of approved quality).

12mm cement plaster 1:4 (1 cement: 4 fine sand)

6mm cement plaster to ceiling 1: 4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Providing and laying 20mm thick cuddapah in shelves over 20 mm thick base of cement mortar 1:3 complete

Providing and fixing coloured ceramic tiles spartek or equivalent of 12 " x 12" (399x150 mm cut size) 6 mm thick in skirting and dados on 12 mm thick cement plaster 1:3 (1 cement: 3 coarse sand) and jointed with cement slurry complete.

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete b) Light Shades

Providing and and laying vitrified floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete b) 600 x 600 mm light Shades

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete. b) 600 x 600 mm light Shades

Providing and fixing white vitereous china pedestal type (Europen type) water closet with seat as lid, whth em C.I. brass hinges and rubber fitings 15 lts white vitreous china low level flushing cistern with fittings as 3 brackets 40 mm white precelain 3enameled flush bad, 25 mm overflow pipe with specials and mosquito proof coupling of approved municipal design complete, including cutting and making good the walls and floors where required.: a) W.C. pan with white plastic seat and lid

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. (a) brass trap and union complete, including cutting and making good the walls where required. a) Flat back wash basin size 630 x 450mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone mand making good the walls wherever required. Kitchen sink without drain board. with coupling & all 2 accessories complete with choke stop strainer, Plain type having flat borders for correct sandwiching between the platform top and bottom slabs complete. Overall size 610mmx510mm (24"x20") bowl size 545mmx445mmx200mm (211/2"x 17 1/2"x 8") depth 200 mm. Glossy. 1.0mm thk,

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing NICKEL chrome plated copper alloy Fancy wall mixer with 3 IN 1 SYSTEM WITH 115MM long bend pipe for connection to over head shower Jaquar make or equivalent. Confirming to IS 8931;1993

Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality: a) High pressure with P.V.C. floats: 1) 15 mm nominal bore

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws 750 x 20 mm size

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed: a) 110 mm dia

75 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. a) 110 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. b) 75 mm dia

Providing and fixing NICKEL chrome plated copper alloy Fancy long body make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing nahani trap of rigid PVC (approved make) for S.W.R. pipes including lubricating etc complete, without door: a) 110 mm dia

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with sheet flance 20mm Jaquar make or equivalent. Confirming to IS 8931;1993: a) 20mm nominal bore

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. a) 15 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. b) 20 mm dia nominal outer dia pipes

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge. (External work (heavy duty SDR 11 pipe) d) 32 mm nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge. (External work (heavy duty SDR 11 pipe) e) 40 mm nominal outer dia pipes.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (c) Group C -- with Cat A Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with 2 way modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) with Cat A Modular accessories

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. (c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. (i) 4 x 4 sq.mm + 2 x 4 sq.mm earthwire (25mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. (j) 4 x 6 sq.mm + 2 x 6 sq.mm earthwire (32mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. (k) 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit)

Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required(a) Cat 6

Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required (a) 2 Pair

Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required (d) 20 Pair

Supplying and fixing of following sizes of rigid PVC conduit along including cutting the wall and making good surface(medium)/recess(heavy) recessed conduit as required. (a) 20mm

Supplying and fixing of following sizes of rigid PVC conduit along including cutting the wall and making good surface(medium)/recess(heavy) recessed conduit as required. (b) 25mm

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch connection painting etc. as required. (a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet (a) Cat modular socket outlet and 15/16 A modular switch connection painting etc. as required. (a) Cat A

Supplying, installation and testing of suitable size modular GI box, modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. CAT A

Supplying, installation and testing of suitable size modular GI box, modular plate and cover complete with RJ-11 connector(modular telephone socket) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. CAT A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but 7001(h) without MCB/RCCB/Isolator) (h) 16 way double door Cat A

Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator) (e) 12 way (8+36), double door, Horizontal type Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (a) SP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (b) SPN, Cat A

Supplying and fixing 50 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat A

Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat A

Supplying, erecting & commissioning 2 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB.

Supplying, fixing and commissioning 2 pole RCBO up to 25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCBO.

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 25 sq.mm

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (6) 4 x 25 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface, etc. complete as required

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete.

Providing & erecting hot dipped galvanised perforated type cable tray manufactured from 16 SWG GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Supplying and erecting LED square / circular Max. 14 W down lighter /Panel Light having pressure die-cast aluminium housing, polystyrene diffuserhaving system lumens output of Min. 1500 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Supplying and erecting LED square / circular Max. 18 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG IDF/LED.

Supplying and erecting LED Strip light Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs at L70B50 including driver with minimum 1 year warranty as per specification No. FG-IDF/LED.

Supplying and erecting anodized aluminium mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<20%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs at L70B50 including driver with end caps on provided PVC Block / wooded board with minimum 2 years warranty as per specification No. FG-IDF/LED.

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B- 22/E-27 base as per specification no. FG-LP.

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and 'E' class insulation.

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, Max. Energy Consumption of 28W having service ratio (CMM/W) of Min. 8, PF>0.9, THD<10% with IR remote control, Temperature Rise of Max. 40 deg.C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF

Providing and erecting ms fan clamps of required size fixed with two numbers anchor bolts of 10 mm dia grouted in RCC slab with injectable chemical mortar including drilling of holes, etc complete

Supply and erecting meter box suitable for three phase energy meter and incoming TP/TPN MCB, fabricated out of 16 SWG sheet steel, powder coated, complete as required and conforming to the requirements of Goa Electricity Department

Supply, installation, testing and commissioning of electronic type three phase energy meter (KWh), 4 wire, ISI marked, in polycarbonate or sgheet steel body (base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only. (c) 50 to 100 A

Supplying, installing, testing and commissioning of Junction Box, ITD/DOT approved, indoor type with wall mounting/concealed facility having front door with lock along with aluminium frame for mounting disconnection type Krone modules, complete cabinet fabricated from 18 SWG CRCA sheet with powder coating in appropriate manner and suitable for following capacity of pairs, including Krone makemodules, crimping and terminations, etc. complete as required. (b) 20 Pair

Supplying and fixing 12U wall mount rack (Dimension-DxWxH - 500x550x613mm) as per specification no. WG-NAS/RAK

Supplying and fixing Cat 6, 24 port patch panel with keystone jacks compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 complete as per specification no. WG-NAS/PP

Supplying and fixing 1 m 24 AWG multi stranded UTP patch cord with RJ-45 factory crimped connector of Cat 6 type, compliant ANSI/TIA-568.2-D standards in position as per specification no. WG-ELVC/PC

Supplying, fixing, and configuring 24 ports with 4 combo SFP Port ethernet managed switch compliant with IEEE 802.3 standards, min. 370W PoE capacity, with web view ethernet port for management in provided rack as per specification no. WG-NWC/GBS

Supplying, fixing, and configuring 8-ports 1 GE un-managed gigabit PoE switch compliant with IEEE 802.3 standards, min. 120W PoE capacity with 2GE SFP uplink erected in provided rack complete.

Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 6 x 16 universal extensions compliant to IEC 61000, EN 60950, CISPR 22, IS:9000 part 2/section 4 having LAN/WAN Port, USB port, RS232 port as per specification complete as per specification no. WG-TA

Supplying, installing, testing & commissioning of 8/10 Ch. Network Video Recorder (NVR), suitable for 2 MP cameras only with HDMI/VGA outputs provided HDMI output of 4K resolution or VGA output with output up to 1920 × 1080. Support H.265 or higher, H.264, MJPEG, Incoming Bandwidth 160Mbps with minimum 2 SATA Hard Disks, ANR Technology, 2 SATA interfaces for 2 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 4/1, RJ-45 10/100/1000 Mbps self-adaptive Ethernet interface, support multibrand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer. support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specifications no. CCTV-NVR

Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 210 MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64, Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specification no. CCTV-HDD

Supplying & erecting of High definition 2 Megapixel IP IR Dome Camerawith following featuresImage Sensor: minimum 1/2.8" Progressive Scan CMOS, Video Resolution: minimum 1920 x 1080 Video Compression: H.264, H.265 or higher, at least Three individuallyconfigurable stream, Frame rate: minimum 25 fps at all resolutions, WDR: minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance: 30m, Lens Type: 2.8/4/6 mm Lens, fixed focal, Field of View :2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129°4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102°6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65°Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 30m. Camera minimum Adjustment Angles Pan: 350°, Tilt: 72°, Rotate: 350°. Power Supply: Support 12VDC & PoE, IP67, IK10 Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum ts/screws to take care of undulations in the floor level. Tiles: The fabric tile panels will be Constructed out of 4mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. One of the tile panel will be Whiteboard marker tiles made out of 4mm MDF with 1mm glossy face laminate with a balancing laminate on the back. And one of the tile panels will be Magnetic tile Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Wire management: Internal Concealed raceways to be provided below work surface with switchboard arrangement for Power & Data along with PVC Wire manager with Grommet / scallops & Individual raceway arrangement for Data/ Power cable. Drawer Pedestal: The Pedestal Unit of Dimensions 400W x 470D x 675mmH will be made of 18mm thick pre laminated particle board. All the exposed edges will be sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer fascia will be sealed with 2mm thick PVC edge. STQC or any indian standards as applicable, CE, FCC certified.duly erected in position on wall/ceiling/false ceiling/provided pole (mountingheight not more than 5 meter) etc with all accessories etc complete as perspecification no. CCTV-CAM

Supplying & erecting of High definition 2 Megapixel IP IR Bullet Camera with following features: Image Sensor: minimum 1/2.8" Progressive Scan CMOS, Video Resolution: minimum 1920 x 1080 Video Compression: H.264, H.265 or higher, at least Three individuallyconfigurable stream, Frame rate: minimum 25 fps at all resolutions, WDR: minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance: 30m, Lens Type: 2.8/4/6 mm Lens, fixed focal, Field of View :2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129°4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102°6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65°Lux sensitivity minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White,0.0 Lux (IR) Night Vision Distance minimum IR - 30m. Camera minimum Adjustment Angles Pan: 350°, Tilt: 72°, Rotate: 350°, Power Supply: Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. miniine with the Top trims & end trims. The partitions will be provided with leveling bolts / screws to take care of undulations in the floor level. Tiles: The fabric tile panels will be Constructed out of 4mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. One of the tile panel will be Whiteboard marker tiles made out of 4mm MDF with 1mm glossy face laminate with a balancing laminate on the back. And one of the tile panels will be Magnetic tile Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Wire management: Internal Concealed raceways to be provided below work surface with switchboard arrangement for Power & Data along with PVC Wire manager with Grommet/scallops & Individual raceway arrangement for Data/ Power cable. Drawer Pedestal:- The Pedestal Unit of Dimensions 400W x 470D x 675mmH will be made of 18mm thick pre laminated particle Board conforming to IS: 12823 Interior Grade. All the exposed edges will be sealed with 2mm thick PVC Imported edge banding on sides and bottom. The top and drawer fascia will be sealed with 2mm thick PVC edge. The drawer unit will consist of 2 box drawer and 1 file drawer. The sides of Inside drawer box will be of prelam pa

Supplying & erecting 32" professional LED Monitor with 1920*1080 (FullHD) Display, suitable for 16 channel NVR and following featuresBrightness: minimum 250 cd/m2Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg.Response time: maximum 8 msInputs: HDMI, VGA, BNC, USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle dulyerected on wall or table top with standard accessories like wall mount stand andwiring connections etc. complete as per specifications no. CCTV-MON

Supplying, fixing, and configuring 1200 Mbps dual band wireless router having 4 Nos. of 10/100/1000 LAN ports external with 4 nos. of external antennas compliant with IEEE 802.3 standards erected on desktop/wall complete.

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and ST watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge. The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs (paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately). (b) In rocky strata

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge. The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c) Watering GI pipe, 20 mm Class B, with funnel as per specs. d) Charcoal/salt as per specs (paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. g)watering arrangement (plumbing will be paid seperately). (b) In rocky strata

Extra for using salt and coke for GI or copper plate earth electrode as required( 240 Kgs of Coke and 5 Kgs of Salt)

Supplying and laying 25 mm x 6 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Supplying and laying 25 mm x 5 mm copper strip in 40 mm dia GI pipe from earth electrode as required

Providing and fixing 25 mm x 6 mm GI strip on surface or in recess for coneections etc. as required

Providing and fixing 25 mm x 5 mm copper strip on surface r in recess for coneections etc. as required

Supplying, erecting, testing & commissioning of 6 kVA capacity on line pure sine wave,PWM,IGBT based UPS with 0.9 to unity output pf,single phase input & 1 phase output complete with all protections as per specification no. AP- UPS (Without batteries)

Supplying and erecting 12 V/26Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete

Supplying, erecting, testing and commissioning of diesel generating set withalternator of 30 kVA output continuous rating, 3 phase, 415 V, 50 Hz, 0.8 p.f.,A.C. supply, a totally enclosed air cooled / liquid cooled multi-cylinder dieselengine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12hours, along with standard accessories, self-excited, self-regulated, screenprotected alternator with static excitation system running at 1500 RPM as per IS4722-2001 with voltage regulation +/- 5%, with performance class G2/G3 andmaximum fuel consumption 5.9 ltr/hr @75% loading. Both the engine andalternator direct coupled on a common fabricated steel base frame and mountedon anti-vibrating pads, with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete setenclosed in composite acoustic enclosure as fully assembled integral unit made of16 SWG CRCA sheet, sound absorbing material to restrict sound level up to 75dB at 1.0 m, provided with first filling of oil, diesel not less than 65 ltr etc., on provided M20 grade CC foundation as per specification no. GEN-DG

Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 25 kVA upto 35 kVA capacity 3 phase, 415 V, 50 Hz, A.C. supply with all standard features, safeties etc as per specification no. GEN-AMF.

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.0TR to 1.2TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/SAC

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/SAC

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor. room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 5.0 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position in provided recess with wooden frame complete specification no. AP-AC/SAC

SHIVAM INFRATECH (BID ID -55482)

Desh Pande Construction (BID ID -55604)