SPECIAL REPAIRS TO CERTAIN OMQs (542(02) Sqn Ldr Pool 110 (02) P-51 Flt Lt Pool AT AF STATION SURATGARH

Amount

(SPECIAL REPAIRS TO CERTAIN OMQs {(542(02) Sqn Ldr Pool, 110 (02) & P-51 Flt Lt Pool} AT AF STATION SURATGARH)

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Demolition of stone or brick masonry built in cement mortar including all quoins, arches etc.but excluding ashlar facing, dressed stone work etc, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6, complete all as specified and directed.

All as per Srl item No. 3 here-in-before but except bricks.

M&L for brickwork with sub class 'B' bricks, straight or curved on plan exc. 6m in mean radius, built in cement mortar 1 :4 in half brick thick wall, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6, type C2, using 40mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified and directed.

Taking down chowkats or frames wirh shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified and directed.

M&L for Pressed steel frames of size 105mmx60mm made of 1.25mm thick Cold Rolled sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling of hollow portion with PCC 1:3:6 type C-1 using 20mm graded stone aggregate, complete all as specified and directed.

M&L for Pressed steel frames of size 125mmx60mm made of 1.25mm thick Cold Rolled sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling of hollow portion with PCC 1:3:6 type C-1 using 20mm graded stone aggregate, complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneering on both faces.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

S&F 35mm thick factory made 2nd class hardwood (Sal/ Hollock) glazed and skelton shutters open rebated and prepare to receive glass guage (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass/guage etc size of member etc size members of shutters as specified in SSR part I Section-8 clauses 8.24(a) supplied and fitted to chowkhat, complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement from stiles and plain colour PVC sheet to be fitted with MS frame welded/sealed to the styles & rails with suitable PVC sheet beading, and jointing together with solvent cement, supplied & fitted in the frame at site as per specification & drawings, complete as specified and directed.

S&F butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked), complete all as specified and directed.

S&F butt hinges, stainlees steel 100mm long (ISI marked), complete all as specified and directed

S&F extruded aluminum alloy handles, 150 mm size fabricated type anodised complete all as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long (ISI marked), complete all as specified and directed.

S&F aluminium alloy, 16mm dia and 250mm long anodised, sliding door bolt with hasp and staple (bolt type) with and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, complete all as specified and directed.

S& F in repair 150mm mild steel Brass ordinary rat tail rod pattern springs including roller and rollar plate, fixed including welding/ fixing to steel/ wooden chowkats, complete all as specified and directed.

S&F Aluminum floor door stopper 63 mm with two rubber legged, complete all as specified and directed.

M&L for anti snake rubber beading 75 mm wide 4 mm thick for fixing with door shutter and similar situation including necessary drilling and cutting etc, complete all as specified and directed.

S&F peg set of six made of stainless steel, complete all as specifed and directed.

S&F Aluminum powder coated window and ventilator shutters, sliding type with four track (two track with and including galvanised mild steel wire cloth 0.50 mm nominal dia of wire & average width of aperature 1.00 mm and fixed with tinned tacks or galvanised wire staples, two track with and including 4.8 mm thick tinned glass including necessary fitting and fixture) without sash bars, aluminum sections of size 40x20x1.5 mm fixed in aluminum anodised double frame of section size 63X35X2 mm including necessary jointing cleats, glazing clips, aluminum anodised snap beading, screws, aluminium beading, pvc packing, aluminum anodised fitting and fixture including powder coating of thickness n.exc 50 micron on all aluminium section, Aluminium chequered grills as on aluminium windows weight not less than 1.0 kg/sqm complete all as specified and directed.

S&F steel window with side hung shutter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

S&F steel window with side hung shutter including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges with steel peg stay, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame/steel frame or stone, concrete or brick surrounds, glazed with putty or fixed with beads, exc 1.5 sqm, complete all as specified and directed.

M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in squares not exc. 0.5 Sqm in each pane, complete all as specified and directed.

M&L for figured glass, pin headed type, 3mm thick and glazing with oil putty or wooden beads in squares not exc. 0.5 Sqm in each pane, complete all as specified and directed.

S&F Stainless Steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified and directed.

S&F in repair stainless Steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified and directed.

Supply and fix factory made mild steel cupboards shutters 1 mm thick with frame made from 1.25 mm thick sheet including all fittings i.e. mortice lock with handle ,butt hinges ,peg set of three,etc including two coats of synthetic enamel paint over a coat of primer, complete all as specified and directed.

S&F in repairs 2nd class hard wood plain fillets square or rectangular or tri angular in section and bull- nosed, splayed, chamfered or rounded on one edge or face, clean sawn planed on both sides secured with nails or beads in section exc 3 sq cm & n-exc 6 sq cm in cup board or drawer frame work, complete all as specified and directed.

M&L in repairs for block boards 18/19 mm thick , grade 1 quality, exterior grade, decorative type with decorative face veneer on one face in Cup Board or drawers complete all as specified and directed.

M&L for Decorative laminate 1.5 mm thick type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions with Cup Board,cabinet or drawers complete all as specified and directed.

S&F in repairs Continuous (piano) hinges 30 mm width of flaps, mild steel, bright finish or electro galvanised with Cup Board or drawers complete all as specified and directed.

S&F in repairs wooden decorative type handle 100mm long for cup board, cabinet or drawers, complete all as specified and directed.

S&F in repairs T-C steel Telescopic ball bearing drawer channel (silver) using for modular kitchen , cabinet drawer, loading capacity-45 kg complete all as specified and directed.

S & F in repairs 100 mm Hasp & Staple extruded aluminium alloy , fabricated type, anodised including bolt to hinge plate and fixed with screws with Cup Board shutter, complete all as Specified and directed.

S&F in repairs cupboard, cabinet or drawer knobs wooden polished fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S&F in repairs magnet catchers brass body suitable for cup board shutter, complete all as specified and directed.

Taking down cement plaster on brick or concrete wall surfaces etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for 10 mm thick rendering in cement mortar 1:3 on concrete surfaces of roof projection ceiling etc including repairing of broken portion up to 6m height and surface finished even and smooth (without using extra cement), complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) on wall complete all as specified and directed.

M&L for complete removal of existing treatment from wall surfaces and applying one coat of Dr fixit solution to avoid seepage lekage and effect of effloracence, complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and fair without using extra cement but using water proofing compound as per manufacturer's instructions, complete all as specified and directed. Note :Water proofing compound shall be measured & paid seprately.

M&L for rough cast plaster with a mixture consisting of crushed stone or fine gravel aggregate of size 6 to 8mm as directed, mixed with coarse sand and cement in the ratio 1:1:1, finshed even over rendering with under coat of 15mm thick cement and sand mortar 1:4, complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of wall and applying two coats of oil emulsion distemper over one coat of primer and over and including 1-2mm thick JK/Birla wall care putty to achieve smooth finish surface, complete all as specified and directed.

M&L for complete removal of existing treatment from wall surfaces and applying 1-2 mm thick JK/Birla wall care putty to achieve smooth finish surface, complete all as specified and directed.

M&L for preparation of plastered or unplastered old decorated surfaces on wall including cornices pilasters by brooming down or steel wire brushing, scraping down,smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white wash on wall, complete all as specified and directed.

M&L for preparation of plastered or unplastered old decorated surfaces on ceiling including cornices pilasters by brooming down or steel wire brushing, scraping down, smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of white wash on ceiling complete, all as specified and directed.

M&L for preparation of old decorated surfaces plastered or unplastered on walls including cornices pilasters by brooming down or steel wire brushing and efforescent salts and applying two coats of distemper oil emulsion complete all as specified and directed.

Complete removal of existing treatment and applying multi colour rustic texture coating on walls including preparation of surfaces using wall care putty 1 mm thick complete all as per manufactures instruction and complete all as specified and directed.

Applying two coats of exterior acrylic emulsion (weather proof treatment ), in camouflaging patterns, over new plastered surfaces , including preparation and using primer on new surfaces ,complete all as specified and directed.

Applying two coats of exterior acrylic emulsion (weather proof treatment), in camouflaging patterns , including preparation of old surfaces like brooming down or steel wire brushing scraping down smoke soot, moulds mass and efflorescent salt and trading oil and greasy spots complete all as specified and directed.

M&L for prepration of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for prepration of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparation of old painted surfaces, of wood and wood based material of any description over 10cm width or girth by cleaning, sand papering, brushing etc, filling in crevices and cracks etc with approved filler and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing old painted surfaces of steel and iron surfaces, over 10 cm in width or girth by cleaning, sand papering, brushing with wire brushes, scrapping by steel scrappers etc, filling in crevices and cracks etc. with approved filler and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition), complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads breaks in floor, window cills, concrete railing, openings in concrete walls, floor and roofs and similar works exc 5cm but n.exc 10cm wide rough finish surface of concrete, complete all as specifed and directed.

M&L for precast cement concrete (nominal mix), type B-1, 1:2:4 using (20mm graded crushed stone aggregate) as in landings, cover slabs (for manhole etc.), and similar articles with plain faces, set in cement mortar 1:6, complete all as specified & directed.

M&L for Reinforced cement concrete, type A-1 (1:1.5:3) nominal mix, using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for TMT mild steel bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for joint free non skid coloured glazed ceramic tiles of approved shade of size 300x 200 mm x 7 mm thick as in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 10mm thick backing coat in cement mortar 1:4, complete all as specified and directed.

M & L Vitrified ceramic tiles 10mm thick (Square/rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade including 15mm thick screed bed or bedding layer in Cement Mortar (1:6) as in floor finished even and rough to receive the top layer, complete all as specified and directed.

All as per item No 71 above but on vertical surfaces such as dado, skirting etc over and including 10 mm thick backing coat finished even and rough to receive tiles in Cement mortar (1:4) complete all as specified.

M&L joint free non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but n exc 0.18 Sqm, in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Demolition of stone slabs/paver block and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, complete all as specified and directed.

M&L for machine cut polished kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over 20mm thick screed bed in cement mortar 1:6, including rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed.

M&L for polished kota stone slab 18 -20 mm thick in riser of steps, skirting, dado and pillar laid over backing coat and jointed with grey cement slurry mixed with pigment to match the shade of the slab, over 10mm thick backing coat in cement mortar 1:3, including rubbing, grinding, rounding of edges and polishing to achieve mirror finish, complete all as specified and directed. Note : Kota stone shall be laid in one pieces for treads and risers for step, window cills and moulding/rounding of edge properly.

M&L for Udaipur green marble (of any type) 14 to 16 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble stone, laid over and including 15mm thick screed in cement mortar 1:4, rubbing, grinding, rounding of edges and polishing(table rubbed & polished) to achieve mirror finish and ,making hole in stone and RCC shelves suitable for gas pipe, with round edges where required, complete all as specified and directed.

M&L for Plain cement concrete (1:4:8), type D-2, using (40 mm graded mechanically crushed stone aggregates) 75mm thick as in sub base or in mass concrete or in base layer, complete all as specified and directed by Engineer-in-Charge.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick set jointed and pointed in neat cement slurry in floors with in grey cement and pigment over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel 25 mm dia curtain rod including stainless steel brackets and stainless steel end knobs fixed with plugs & screws, complete all as specified and directed.

S&F in repairs Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests, white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, complete all as specified and directed.

Supply and fix in repair Vitreous china wash down water closet pan (Pedestal pattern) incl one toilet paper holder, one health faucet and jet ingrated controlled by two way angle valve) incl plastic water closet seat white colour closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging devices complete all as directed and specified by Engr-in-charge.

S&F in repairs, PVC valveless, dual type, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, including 32 mm dia PVC long bend flush pipe 90cm long, complete all as specified and directed.

S&F in repairs vitreous china wash hand basin flat back 550 x400 mm size white, first quality, with and includingPVC waste coupling 32mm size, PVC waste pipe 32mm bore, brackets of Mild Steel angle iron of suitable size including two coat of synthetic enamel paint over a coat of primer brackets fixed to walls, compelte all specified and directed.

S&F in repairs, 15mm bore, Brass CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F in repairs stop valves, 15mm bore, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., complete all as specified and directed.

S&F in repairs PVC connection 15mm dia, 600mm long, hot water grade with brass chromium plated nuts and washers at both ends, complete all as specified and directed.

S&F in repair Stop valve,15 mm dia cast copper alloy chromium plated fancy type with long shank &cup(concealed type) with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for iron pipe complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose of 125mm size with or without swivel joints any size, including fixing to steel pipe, complete all as specified and directed.

S&F in repairs, sink with drainage board made out of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes coupling, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size 915mmX460mm bowl size 410mmX330mmX160mm, complete all as specified and directed.

S&F stainless steel Plate rack 1mm thick of overall size 750mmx600mm Grade -304 including shelves rod for putting plates etc, complete all as specified and directed.

S&F in repairs bib tap, 15mm bore, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repair 15mm wall mixer fancy type cast copper alloy chromium plated high pressure with crutch or butterfly handle non telephonic complete all as specified and directed.

S&F in repairs soap dish, brass chromium plated of suitable size and 1mm thick, complete all as specified and directed.

S&F in repairs tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

S&F sheet glass corner set of 5.5 mm thick glass of 3 pieces with chromium plated stopper as per sample approved by Engr -in-charge, complete all as specifed and directed.

S&F in repeair sheet glass 5.5 mm thick WHB Shelf 600 mm long and 125 mm wide with chromium plated stopper as per sample approved by Engr -in-charge complete all as specifed and directed.

Dismantling water tank of capacity exc 250 and n exc 500 ltr of any type, PVC/RCC/MS complete all as specified and directed.

S&F Rotational moulded plythelene white water storage tank tripple layered white coloured, 1000 litres capacity (cylinderical vertical with closed top) hoisted with thread tank cover and fixed in position including GI tank nipple & with union(two nos each), including 20mm ball valve of brass, high pressure, with polythene float and fly nut complete all as specified and directed.

S&F Rotational moulded plythelene white water storage tank tripple layered white coloured, 500 litres capacity (cylinderical vertical with closed top) hoisted with thread tank cover and fixed in position including GI tank nipple & with union(two nos each), including 20mm ball valve of brass high pressure, with polythene float and fly nut complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves of 20mm dia, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

S&F in repairs stop valves, 15mm bore, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends screwed for iron pipe or for union etc., complete all as specified and directed.

S&F in repairs PVC (SWR) pipes, 110mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

S&F in repairs 110mm bore PVC (SWR) bends any radius, complete all as specified and directed.

S&F in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval, complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) bends any radius, complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) junction single (Single T ) equal or unequal, complete all as specified and directed.

S&F in repairs 100mm bore spun Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors/wall complete all as specified and as directed.

S&F in repairs 75mm bore spun Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors/wall complete all as specified and as directed.

S&F in repairs CI Bends (any radius), diminishing piecs or tapers (larger bore measured) for 100mm bore pipe fitted with oval access doors complete all as specified and as directed.

S&F in repairs CI Bends (any radius) with duck's foot or heel rest for 100mm bore pipe fitted with oval access doors complete all as specified and as directed.

S&F in repairs CI Bends (any radius) with duck's foot or heel rest for 75mm bore pipe fitted with oval access doors complete all as specified and as directed.

S&F in repairs Cast iron Nahani trap of 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.

S&F in repairs Cast iron floor trap of 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.

S&F in repairs 100 mm bore CI cast iron cowls complete all as specified and directed.

S&F in repairs brass chromium plated grating 100 mm dia complete all as specified and directed.

S&F in repairs brass chromium plated grating 125mm dia with waste hole, complete all as specified and directed.

Taking up or down GI tubing of 15mm bore with all connections and fittings including cleaning for refixing or removal to store, complete all as specified and as directed by Engineer-in-Charge.

Taking up or down GI tubing of 20mm bore with all connections and fittings including cleaning for refixing or removal to store, complete all as specified and as directed by Engineer-in-Charge.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps & similar work etc. and cutting chases for concealed water tubing and making good, cutting exc 10cm but not exc. 20cm girth in brick walls, complete all as specified and directed.

S&F galvanized iron water tubing, ‘medium grade’ 15mm bore, with all fittings such as bend, tee, union etc., fixed complete to walls and ceilings or laid in floors, complete all as specified & directed.

S&F galvanized iron water tubing, ‘medium grade’ of 20mm bore, with all fittings such as bend, tee, union etc., fixed complete to walls and ceilings or laid in floors, complete all as specified & directed.

Refixing old steel tubing of 15mm bore and connections in new or old position (Walls, ceiling, floors etc.), complete all as specified and directed.

Refixing old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors etc.), complete all as specified and directed.

Taking down existing existing water proofing treatment from the top of RCC/arch slab, including taking down existing PCC padding tiles mud phuska or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish outside the premises, complete all as specified and directed.

M&L for PCC type B-1(1:2:4), using 20mm graded crushed stone aggregate as in PCC padding on depression of roof finished even and fair without using extra cement, complete all as specified and directed.

M&L for Water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of cleaning of concrete or plaster surface of roof and applying evenly a bitumen primer conforming to IS 3488@ 0.30Kg per sqm followed by a tack coat @ 1.2kg per Sqm using 85/25 grade industrial hot blown bitumen over it laid with APP modified polymeric water proofing membrane minimum weight 3 kg per Sqm and minimum 3mm thick reinforced with non-woven polyester fabric (weight not less than 150 gm per sqm) unrolled & bonded to substrate with longitudinal and end laps 100mm as per manufacturer's instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.2 kg sqm and as per manufacturer instruction and including taking the APP membrane will be required where the parapet wall exceed 45cm for carrying over and taking into parapet walls, cut out neatly a horizontal groove 6.5 cm deep, 7.5 cm wide section with lower edge at not less than 15 cm above the graded roof surface and groove shall be finished smooth with cement mortar 1:4 with WPC @3% by weight of cement where the parapet wall height is 45cm or less no groove will be required as the water proofing treatment will be carried over the top of parapet wall to its full thickness, complete all as specified and directed.

M&L for 15 mm thick screed bed in cement mortar 1:4 on roof surface using water proofing compound as per manufacturer instruction surfaces finished even and smooth without using extra cement as on wall complete all as specified and directed.

M&L for 40 mm thick brick tiles laid on cement mortar and joints grouted flush in cement mortar 1:3 mixed with 5% crude oil by weight of cement on above treated surface, complete all as specified and directed.

M&L for PCC type B-0 1:2:4 using (12.5mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified & directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for cement concrete type E-2 1:5:10 (using 40mm graded aggregate ) as in sunken flooring complete all as specified and as directed.

M&L for appliying two coats of SHALIMAR SUPERCRETE /NITOBOND water proofing coating on the entire surface of sunken portion, complete all as specified and directed.

M&L for 15mm thick cement screed in CM 1:3 admixed with integred waterproofing compound FOSROC's conplast X 421 IC @ 130ml per bag FOSROC's Nito bond AR cement slurry/STP No 1 liquid @ 200ml per bag of complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B0 using (12.5mm graded aggregate) as in sub floor , sub base; concrete surface finished even & rough to receive topping floor/tiles finish/layer complete all as specified and directed.

S&F in repairs 32mm dia High density polyethylene pipes (HDPE) of pressure rating 6kgf/cm2 laid in trenches, complete all as specified and directed.

Supply only integral water proofing compound (ISI marked), complete all as specified and directed.

M&L for repairing of RCC projections, chajjas , roofs, facia etc. by necessary preparation i.e. scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, sufaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregate and reinforced with welded mesh of weight exc 2kg per sq mtr but n.exc 3kg/sqm with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches are n.exc 70mm including applying two coats of finishes to match with the existing surfaces in at any height complete all as specified. Note:- Cost of formwork and welded mesh shall be deemed to be included in unit rate quoted by the contractor.

S&F in repair PVC bath room cabinet of size 400 x 500 mm with mirror, complete all as specified and directed.

Excavating in trenches n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts wells cesspits, manholes, pier holes etc n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in including levelling watering and well ramming in layers n.exc 25 cm thick, complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed.

M&L for 150mm internal dia of salt glazed stoneware drain pipe grade 'A' laid in trenches and joints, complete all as specifeid and directed.

M&L for cement concrete type D2 1:4:8 (40 mm grade aggregate)as in concrete bed to drain pipes 150mm internal dia incl packing under and haunching against the pipe sides of pipe after they are laid and tested, complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) as in foundation filling, mass concrete etc complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 M mean radius built in CM 1:4 including in circular well steining (any radius constructed from the base of curb), complete all as specified and directed by Engr-in-charge.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specifed and directed.

Cutting into existing Manholes for connecting new drains , 150mm dia, making good to pipes and rendering , cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and as directed by Engr-in-Charge

Taking down DB/main switch of any size and making good disturbed surface of wall, complete all as specified and directed by Engineer-in-Charge. Note - Temporary power supply shall be provided by contractor.

Dismantling and taking down fluorescent tube light single/double of any wattage or size street light fittings for repair or replacement of burnt/worm out accessories to MES store complete all as specified and directed.

Taking down unservicable submain wiring copper/aluminium and making good the disturbed surfaces of walls/ floor etc matching with the existing surface, complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminum point wiring (light, fans, socket etc) complete including battens and fittings such as switch, ceiling rose, light fittings, regulators, sockets, light fitting, etc. and making good disturbed surface of wall/floor, etc. complete all as specified and directed by Engineer-in-Charge. Note :- Temporary power supply shall be provided by contractor.

Taking down fan of any type, sealing cable end, dismantling blades and removing fan and blades to store and refixing the same, complete all as specified and directed.

M&L for Point wiring (concealed) complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though medium grade rigid PVC conduit, ISI marked, 19/20 mm dia including all accessories on the surface of walls/floors/ceilings and making good the disturbed surface, with and including sunken type pressed steel/welded MS terminal box 1.2 mm thick bakelite laminated sheet top cover 3 mm thick and 1.5 Sq mm copper earth continuity wire connected to earth dolly, complete all as specified and directed by Engineer-in-Charge. Note : Metal flush box shall be deemed to included in the quoted rate.

One light point/ceiling fan/exhaust fan point controlled by one switch.

One 3 Pin socket outlet 5 Amp on the same board.

One 3 pin socket outlet 5 amp on the independent board.

One 3 Pin socket outlet 15 Amps, independent with cables 4 Sqmm size.

S&F LED tube light fitting 18 to 20 Watt with batten luman maintenance>70% at 50,000hrs, color temperature of 5000-6500K,> color rendering and LM80 test compliance. The driver must be integral APFC and constant current type having THD<15% and power factor>0.95 with short circuit protection, open protection, reverse polarity protection, high voltage protection complete all as specified and directed.

S&F LED mirror optic tube light fitting 10 Watt with batten luman maintenance>70% at 50,000hrs, color temperature of 5000-6500K,> color rendering and LM80 test compliance. The driver must be integral APFC and constant current type having THD<15% and power factor>0.95 with short circuit protection, open protection, reverse polarity protection, high voltage protection complete all as specified and directed.

S&F Step 0-4, modular type electronic regulator for ceiling fan 1200 mm sweep, 240 volts, 100 Watts humfree single pole, complete all as specified and directed by Engineer-in-Charge.

S&F Switch modular type, single pole one way 6 Amps, module 240 volts Ac suitable for modular switch boxes without indicator, complete all as specified and directed by Engineer-in-Charge.

S&F Socket modular type single pole 6 Amps 2/3 pin combined 2 module 240 volts, complete all as specified and directed by Engineer-in-Charge.

S&F Ceiling rose, 3 phase/PVC/polyeabnote, isolated body, 65mmx50mm, complete all as specified and directed by Engineer-in-Charge.

S&F Socket modular type 16 Amps, 3 pin combine, 2 module,240 volts , complete all as specified and directed by Engineer-in-Charge.

S&F Switch modular type 1 way 16 Amps, 1 module,240 volts, complete all as specified and directed by Engineer-in-Charge.

S&F Sheet metal enclosure with socket plug top single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 amps , 240 Volts, complete all as specified and directed by Engineer-in-Charge.

S&F Sheet metal enclosures for SPN DB's with double glazed door for incorporating MCBs,IP-43 , 8 way with 200 amps rated busbar, 240 volts, as per IS-8623, fixed in repair complete all as specified and directed by Engineer-in-Charge.

S&F Sheet metal enclosures for SPN DB's with double glazed door for incorporating MCBs,IP-43 , 12 way with 200 amps rated busbar, 240 volts, as per IS-8623, fixed in repair complete all as specified and directed by Engineer-in-Charge.

S&F vertical TPN DB 6 way double door having, IP:43 Protection, Shrouded Neutral Bar & Pan assembly with flexible connecting link, cement spill protector, door earthing with provision of MCCB upto 125 Amps, complete all as specified and directed.

S&F vertical TPN DB 4 way double door having, IP:43 Protection, Shrouded Neutral Bar & Pan assembly with flexible connecting link, cement spill protector, door earthing with provision of MCCB upto 100 Amps, complete all as specified and directed.

S&F MCCB four poles, 100 Amps, breaking capacity 25 KA with adjustable thermal and magnetic setting conforming to IS-8828, 415 Volts, 50 Hz including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc, complete all as specified and directed.

S&F MCCB four poles, 63 Amps, breaking capacity 25 KA with adjustable thermal and magnetic setting conforming to IS-8828, 415 Volts, 50 Hz including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc, complete all as specified and directed.

S&F MCB SPN 32 amps 'C' series, breaking capacity 10 KA, 'C' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP, 6 to 32 Amps, C series, breaking capacity 10 KA, 'C' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

S&F ceiling fan 5 star rated copper wound 230V, 50 Hz, complete all as specified and directed by Engr-in-Charge.

S&F exhaust fan 300mm sweep, 900 RPM 230 Volts single phase AC Supply with louvers complete with bolts, nuts and washers, suitably embedded in the wall making suitable opening and provisioning of flexible copper cord three core PVC sheathed of size 23/0.0076 from ceiling rose to exhaust fan, complete all as specifeid and directed.

S&F LED street light 45W with IP-66 protection, 50Hz single phase with support calmp fixed on wall and with flexible wire, complete all as specifeid and directed. Make:- Crompton Cat part No- CRP-409-45-57-SL-GL-NSG or equivalent make as specified Appx 'B'.

S&F submain wiring with 2 runs of copper conductor FR PVC insulated unsheathed cable 1100 volts grade 6 sqmm drawn through PVC conduit medium grade ISI marked 25mm dia as per IS specification fixed concealed in wall/ceiling including conduit and conduit accessories and including provn of PVC insulated 4 sqmm multistranded copper conductor as earth continuity conductor connected to earth dolly complete all as specified and making good to the disturbed surface, complete all as specified and directed by Engr-in-Charge. Note: Two runs of 6 sqmm cable alongwith one run of 4 Sqmm PVC insulated unsheathed copper conductor as earth wire, one run of PVC conduit and conduit accessories shall be measured as one length.

Contract Amount shall be derived after deducting the amount of Schedule of Credit in General Summary on serial page No 16 of tender documents.

M/S VISHNU ENTERPRISES

DIKSHA ENTERPRISES

Aggarwal brothers and company

MSR INFRATECH

PACHR BUILDERS

H S BUILDERS

MISHRA CONSTRUCTION COMPANY