Special Repair of PHC (Health and Wellness Centre) building at Village Balah Kalan in Mohindergarh District. (Re-invited)

Amount

Terracing consisting of tiles 22.86 cm x 11.43 Cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13).

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Make: Duro, Green, Kitply). HSR 17.93 (a)

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA. (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.89).

Providing & fixing vitrified tiles of size 600mm x 600mm of approved make in skirting/dados laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA. (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.90).

Providing & Fixing rectified ceramic anti skid tiles of size 400x400mm of approved make in floors laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note: - Tile shall be of premium quality (1st quality) of reputed manufacturer like NITCO, KAJARIA, SOMANY, ORIENT, JOHNSONS & RACKS (HSR 14.91)

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. Digital Print tiles of Size of 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA shall be used. [HSR 14.92(b)].

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on old work, one coat to give an even shade. (HSR 16.62)

LABOUR FOR LAYING JOINTING, FIXING AND TESTING G.I./P.V.C./W.I.PIPE LINES AND SPECIALS tees bends, sockets elbows etc., INSIDE BUILDING and testing etc., complete including cutting threading. (HSR 28.18) EXCLUDING COST OF SPECIALS (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

EXTRA FOR FIXING AND JOINTING UNION COUPLINGS IN G.I. AND W.I.PIPELINES. (HSR 28.21) 15 mm internal diameter

20 mm internal diameter

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM G.C.I.’P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. (HSR 30.2) Size 580 mm (i) White

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE, EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of- (HSR 30.5)(i) VITREOUS CHINA WARE SYPHONIC SUITE WITH 15 LITRES CAPACITY ATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent;

EXTRA OVER item nos. 30.1 TO 30.4 AND 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. eistern complete (HSR 30.8)

EXTRA FOR providing and fixing 32 MM dia. G.I./C.P.FLUSH PIPE complete with accessories instead of 32/MM dia. galvanised telescopic flush pipe with clips 32 mm dia. C.P. brass flush pipe(HSR 30.15)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design ALL FITTINGS BEST INDIAN MAKE .ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. (HSR 30.41)

PROVIDING AND FIXING IN POSITION 32MM DIA.G.I.WASTE PIPE EMBEDDED IN WALL or lead waste pipe (weighing 3.47kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc., complete (HSR 30.48)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (HSR 30.71)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (HSR 30.75)Bib Cock long body

Bib Cock

Providing and fixing in position C.P. brass stop cocks (HSR 30.76) Stop cock male and female end

Concealed stop cock with flange

PROVIDING AND FIXINGIN POSITION .C.I.SOIL WASTE VENT OR NTISYPHONAGE PIPES TO I.S.I. SPECIFIACTION OF E.L.C. MANUFACTURE OR OF ANY OTHER REPUTED FIRM INCLUDING CUTTING AND WASTAGE ETC. AND CUTTING HOLES IN WALLS, ROOFS OR FLOOR ETC.AND MAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD JOINTING. (HSR 30.84) 100mm internal diameter

75mm internal diameter

PROVIDING AND FIXINGIN POSITION M.S.OR HEAVY FLAT IRON CLAMPS made out of M.S. flat not less than 5 mm of the approved design for fixing C.I. SOIL WASTE vent or anti pipes to walls COMPLETE IN ALL RESPECTS INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS ETC., AND PAINTING. (HSR 30.88) For 100 mm internal diameter pipes

For 50 mm internal diameter pipes

PROVIDING AND FIXINGIN POSITION H.C.I. FLOOR TRAPS I.S.I.MARKED OF THE SELF CLEANING DESIGN WITH C.P. BRASS HIGED GRATING WITH FRAME WITH OR WITHOUT VENT ARM AND INCLUDING CEMENT CONCRETE 1:2:4 under and around the floor trap where required upto floor level COMPLETE IN ALL RESPECTS INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS, ETC., minimum depth of water should be 150 mm with a minimum seal of 50 mm. (HSR 30.89)

PROVIDING AND FIXINGIN POSITION GULLY TRAPS FIXED IN CEMENT CONCRETE 1:4:8 complete WITH H.C.I.GRATING 150 MM X 150 MM CAST IRON COVER WEIGHING APPROXIMATELY 7.26 K.G. AND FRAME CLEAR OPENING 300 MM x 300 MM and outside size 330 MM x 330 MM AND CHAMEBR INCLUDING cost of all brick work in CEMENT MORTAR 1:5 CEMENT CONCRETE 1:8:16 IN FOUNDATIONS, AND CEMENT CONCRETE 1:2:4 IN COPING around C.I. cover and frame etc. (HSR 30.114) 100 mm internal diameter S.W. gully trap

Providing and fixing HDPE Water Storage Tanks of Sintex, Diplast OK Supreme make with covers/lids marked with IS 12701 on roof top of building including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction. (HSR 30.119) 1000 Ltr. Capacity

Supply of G.I. pipe Jindal (N.S.) 15mm dia

20mm dia

Providing G.I. Nipple 20mm dia (NS) 4" Length

6" Length

Providing peet Valve (NS) 20mm dia

25mm dia

Providing and fixing in position best Indian make CP Jet

Providing and fixing best indian make CP Cap

Providing and fixing in position best indian make CP Nipple

Providing and fixing in position best indian make CP Jali complete

Providing and fixing PVC waste pipe 40mm complete

Varun Sharma