87639E8 SPECIAL REPAIRS OF BUILDING NO P72 AND T08 UNDER GE AVADI CHENNAI

Amount

REVISED BOQ UPLOADED ON 28 SEP 2021, BOQ UPLOADED ON 14 SEP 2021 CANCELLED

SCH "A" PART-I (CIVIL WORKS)

Dismantling wrought iron or mild steel work of any description not otherwise provided for and taken on credit complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings and taken on credit complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets and and taken on credit complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 150mm thickness (below or above ground level) and removal of unserviceable debris to outside of MD land complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for and removal of unserviceable debris to outside of MD land complete all as specified and as directed.

Demolition of brickwork or stone boulder masonry, built in cement mortar, including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework and precast concrete articles and removal of unserviceable debris to outside of MD land complete all as specified and as directed.

Demolition of stone slabs / tiles of any description or thickness in floors or vertical surfaces, as in ceramic tiles laid, bedded and pointed in any mortar including bedding screed and backing in vertical surfaces and removal of unserviceable debris to outside of MD land complete all as specified and as directed.

Dismantling of stone slabs / tiles of any description or thickness in floors or vertical surfaces, laid, bedded and pointed in any mortar including bedding screed and backing in vertical surfaces and removal of unserviceable debris out of MD land complete all as specified and as directed.

Taking down chowkats or frames (wooden / steel) with shutters (without taking off shutters from the frames) exceeding 1.50 sqm but not exceeding 4.00 sqm each and removing from site under Sch of credit complete all as specified and as directed.

Taking down chowkats or frames (wooden / steel) with shutters (without taking off shutters from the frames) not exceeding 1.50 sqm each and removing from site under Sch of credit complete all as specified and as directed.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each and taken on credit complete all as specified and as directed.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each and refixing in the same opening complete all as specified and as directed.

(a) The rate is deemed to include easing and adjusting the shuters, altering the size of shutters to suit the floor levels after laying of the flooring.

(b) The rate is deemed to include refixing of builders hardware and renewal of builders hardware as required shall be measured and paid separately as supply only.

Taking down cement plaster any description on brick or stone walls, concrete surfaces, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal of unserviceable debris to outside of MD land complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal from site under Sch of credit of bore of pipe 15mm complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal from site under Sch of credit of bore of pipe 20mm complete all as specified and as directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

Plain cement concrete, type B1, 1:2:4, using 20mm graded stone aggregate as in copings, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating and necessary formwork complete all as specified and as directed.

Brickwork with fly ash bricks, old size, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 of designation 50 complete all as specified and as directed.

Brickwork with fly ash bricks, old size, of designation 50, straight or curved on plan to any radius in half thick brick walls built in cement mortar 1:4 complete all as specified and as directed.

Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, as in IInd class hardwood complete all as specified and as directed.

Factory made plain, framed, panelled shutters (any number of panels), of IInd class hardwood, 35mm thick with panels of wood particle board with commercial face veneers complete all as specified and as directed.

Flush shutters, 30mm thick, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

Factory made Glazed and skeleton shutters, of IInd class hardwood, 30mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, with plain, chamfered or rounded.mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and as directed.

Panel inserts, glass or wire cloth as required shall be measured and paid separately.

Factory made Glazed and skeleton shutters, of IInd class hardwood, 30mm thick open rebated and prepared to receive glass, gauze, etc., edges of framing plain, divided into squares, with plain, chamfered or rounded. mitred and rebated sash bars for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b) complete all as specified and as directed.

Glass or wire cloth as required shall be measured and paid separately.

BLANK

Plain particle board 12mm thick with commercial veneers on both sides as inserts in partly panelled door shutters complete all as specified and as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixed in opening as per relevant drawing in SSR Part-II complete all as specified and as directed.

Factory made solid PVC moulded door shutter, with wood free EPS core 28mm to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on the back face all as per relevant drawing in SSR Part-II complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, overall length of cover plate 150mm, including fixing on floor complete all as specified and as directed.

Mild steel as in small articles such as hold fast and like conforming to Fe-290 Grade-E-165 complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Anodised aluminium snap grid framework of grid size 605mm x 605mm of main and cross tee of size 40mm x 25mm x 1.5mm thick and wall angle size 25mm x 25mm x 1.5mm thick for false ceiling including fixing of supporting hangers complete all as specified and as directed.

The hangers for support of false ceiling shall be measured and paid separately.

Hangers 6 mm dia. G.I. (hanging depth as per site condition) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long at intervals as per manufacturers instructions complete all as specified and as directed.

Semi-Perforated particle board 12mm thick of size 600mm x 600mm in ceiling fixed with screw as per manufacturers and surface prepared and applying two coats of synthetic enamel paint over a coat of pink primer including hidden side complete all as specified and as directed.

Aluminium anodised barrel tower bolts, of extruded section and fixed, length of bolt 300mm complete all as specified and as directed.

Aluminium anodised barrel tower bolts, of extruded section and fixed, length of bolt 150mm complete all as specified and as directed.

BLANK

Aluminium anodised barrel tower bolts, of extruded section and fixed, length of bolt 75mm complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, length of bolt 300mm complete all as specified and as directed.

Butt hinges, medium weight, cold rolled mild steel and fixed / welded to frame of size 100mm complete all as specified and as directed.

Butt hinges, medium weight, cold rolled mild steel and fixed / welded to frame of size 75mm complete all as specified and as directed.

Butt hinges, extruded aluminium alloy, with galvanised mild steel hinge pin, anodised, type C-21 of size 75mm complete all as specified and as directed.

Butt hinges, extruded aluminium alloy, with galvanised mild steel hinge pin, anodised, type C-21 of size 100mm complete all as specified and as directed.

Ordinary rat tail rod pattern springs, 300mm, mild steel, including roller and roller plate complete all as specified and as directed.

Aluminium handles, cast type, anodised of size 75mm complete all as specified and as directed.

Aluminium handles, cast type, anodised of size 100mm complete all as specified and as directed.

Aluminium handles, cast type, anodised of size 150mm complete all as specified and as directed.

40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and as directed.

Tubular towel rail, brass chromium plated, 20mm dia, D type, 600mm long as in repairs between flanges complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples as in repairs complete all as specified and as directed.

Prelaminated particle board minimum 18mm thick, interior grade, one side prelaminated with decorative choice lamination and other side balancing white fixed with screws to timber framework including lipping with teakwood 6mm thick fixed with nails as in repairs complete all as specified and as directed.

Particle board, medium density, minimum 18mm thick, flat pressed, three layer type, with BWR type adhesive, fixed with screws to timber frame as in repairs complete all as specified and as directed.

Steel windows, with side hung shutters, including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and as directed.

Details of steel windows shall be all as per drg Nos. TD-539 Sheet 1/3 to 3/3 and TD-540 Sheet 1/4 to 4/4 available in the office of GE Avadi and the rate quoted shall be deemed to include for the same.

Steel windows, with side hung shutters, including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and as directed.

Details of steel windows shall be all as per drg Nos. TD-539 Sheet 1/3 to 3/3 and TD-540 Sheet 1/4 to 4/4 available in the office of GE Avadi and the rate quoted shall be deemed to include for the same.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

Details of steel windows shall be all as per drg Nos. TD-539 Sheet 1/3 to 3/3 and TD-540 Sheet 1/4 to 4/4 available in the office of GE Avadi and the rate quoted shall be deemed to include for the same.

Mild steel as in framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors and similar work conforming to Fe-290, Gde-E-65 complete all as specified and as directed.

Rolled mild steel as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of grade Fe-290 (Gde-E-165) complete all as specified and as directed.

Plain cement concrete 75mm thick, 1:3:6, type C1, using 20mm graded stone aggregate as in plinth protection / foot path / hardstanding, surface finished fair and even complete all as specified and as directed.

Plain cement concrete, 1:4:8, type D2, using 40mm graded stone aggregate, 100mm thick as in sub-base complete all as specified and as directed.

Chequered cement concrete tiles with grey cement and pigment of size 200mm x 200mm x 25mm thick set, jointed and pointed in neat cement slurry at the rate of 4.20 kg / sqm in floors laid over cement screed in CM 1:4, 20mm thick complete all as specified and as directed.

Non-skid ceramic coloured tiles, minimum 7mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match of superior finish, grade B-II (a) quality over cement screed 1:4, 20mm thick applied with cement slurry at the rate of 3 kg / sqm complete all as specified and as directed.

Non-skid ceramic coloured tiles, minimum 7mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeeding 0.11 sqm, of superior finish, grade B-II (a) quality in vertical surfaces such as skirting, dados, risers etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including a backing coat of cement mortar 1:3. 10mm thick complete all as specified and as directed.

Non-skid ceramic coloured tiles, minimum 7mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match of superior finish, grade B-II (a) quality over cement screed 1:4, 20mm thick applied with cement slurry at the rate of 3 kg / sqm complete all as specified and as directed.

Glazed ceramic tiles coloured of size 300mm x 200mm, minimum 7mm thick in vertical surfaces such as skirting, dados, risers etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including a backing coat of cement mortar 1:3. 10mm thick complete all as specified and as directed.

Granite (of any type) work, of thickness 18mm to 20mm, (table rubbed and polished) in wash basin platforms, cooking platforms, steps, jambs, pillars, windows and the like set in cement mortar 1:4, 20mm thick, including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite stone complete all as specified and as directed.

Cuddapah stone work, of thickness 18mm to 20mm, (table rubbed and polished) in wash basin platforms, cooking platforms, steps, jambs, pillars, windows and the like set in cement mortar 1:4, 20mm thick, including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of the stone complete all as specified and as directed.

Rendering 10mm thick in CM(1:6) on fair faces of brickwork or concrete surfaces as in walls finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15mm thick in CM(1:6) on fair faces of brickwork or concrete surfaces as in walls finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15mm thick in CM(1:4) on other than fair faces of brickwork or stone masonry surfaces mixed with liquid water proofing compound finished as in walls fair and even complete all as specified and as directed.

Supply only liquid water proofing compound shall be measured and paid separately.

Rendering 5mm thick in CM(1:3) on fair faces of concrete surfaces as in ceiling finished fair and even complete all as specified and as directed.

Preparing old plastered surfaces of ceiling and applying one coat of white wash on plastered ceiling surfaces including in narrow widths, bands, cornices, pilasters etc., complete all as specified and as directed.

Preparing newly plastered surfaces of ceiling and applying three coats of white wash on plastered ceiling surfaces including in narrow widths, bands, cornices, pilasters etc., complete all as specified and as directed.

Preparing newly plastered surfaces of wall,, applying two coats of cement paint over a coat of primer to match with the existing adjoining surfaces including in narrow widths, bands, cornices, pilasters etc., complete all as specified and as directed

Preparing newly plastered surfaces of walland and applying two coats of weather proof paint over a coat of primer to match with the existing adioining surfaces including in narrow widths, bands, cornices, pilasters etc., complete all as specified and as directed

Complete removal of existing treatment from wall surfaces, and applying two coats of weather proof paint over a coat of primer to match with the existing adioining surfaces including in narrow widths, bands, cornices, pilasters etc., complete all as specified and as directed

Preparing newly plastered surfaces of wall, applying two coats of distemper oil emulsion white or tinted including in narrow widths, bands, cornices, pilasters etc., over a coat of alkali resistant priming paint over wall care putty 3mm thick, complete all as specified and as directed

Complete removal of existing treatment from wall surfaces, applying two coats of distemper oil emulsion white or tinted including in narrow widths, bands, cornices, pilasters etc., over a coat of alkali resistant priming paint over wall care putty 3mm thick, complete all as specified and as directed

Sheet glass, 4mm thick, ordinary quality and glazing with oil putty / snap beading in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

Preparing new surfaces of wood and wood based materials of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Preparing old painted surfaces of wood and wood based materials of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparing new surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Preparing old painted surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, as in ends of posts, backs of chowkats etc., area exceeding 0.10 sqm but not exceeding 0.50 sqm each and treated with tar or coal tar black paint and sanding complete all as specified and as directed.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, as in small articles such as stop, covers, gully gratings, hold fasts etc., , area not exceeding 0.10 sqm each and treated with tar or coal tar black paint and sanding complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal from site under Sch of credit and provision of steel tubing, galvanised, medium grade, with all fittings such as bends, elbows, tees etc., and fixed complete to walls and ceilings or laid in floors of bore of pipe 15mm complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal from site under Sch of credit and provision steel tubing, galvanised, medium grade, with all fittings such as bends, elbows, tees etc., and fixed complete to walls and ceilings or laid in floors of bore of pipe 20mm complete all as specified and as directed.

Unplasticised PVC pipes of pressure rating 10 kgf/sqcm fixed to walls, ceilings or in floors etc of bore of pipe 15mm complete all as specified and as directed.

Unplasticised PVC pipes of pressure rating 10 kgf/sqcm fixed to walls, ceilings or in floors etc of bore of pipe 20mm complete all as specified and as directed.

Dismantling existing water tanks, exceeding 500 litres and not exceeding 1000 litres, lowering and taken on charge on credit and provision of rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) , three layered hoisted and fixed in position all as specified in SSR Part-I of capacity 750 litres complete all as specified and as directed.

Gun metal, globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed of bore of pipe 20mm as in repairs complete all as specified and as directed.

Bib taps, cast copper alloy, chromium plated, with flange, with crutch or butterfly handle, screwed down, screwed both ends for iron pipe or for brass ferrule and fixed of bore of pipe 15mm complete all as specified and as directed.

Make shall be of Prayag Cat No. Neptune Series PIS-06 or equivalent of makes listed here-in-after.

Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm-210gms) bore of pipe 20mm as in repairs complete all as specified and as directed.

Stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore of pipe 15mm complete all as specified and as directed.

Angle valves / stop valves, fancy type, chromium plated, with flange, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore of pipe 15mm complete all as specified and as directed.

Make shall be of Prayag Cat No. Neptune Series PIS-10 or equivalent of makes listed here-in-after.

Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed for bore of pipe 15mm (Minimum weight 15mm-90gms) complete all as specified and as directed.

Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed for bore of pipe 15mm (Minimum weight 15mm-90gms) as in repairs complete all as specified and as directed.

Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed for bore of pipe 15mm (Minimum weight 15mm-90gms) as in repairs complete all as specified and as directed.

Towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 170 gms) as in repairs complete all as specified and as directed.

Vitreous china squatting pan, "Orissa" pattern, size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) and including fixing of the following components viz. squatt pattern pan with loose cast iron or vitreous chinaware, "P" or "S" trap, seat, flushing cistern, brackets, chain and pull or lever handle, flushing pipe including jointing to socket of flushing rim and connecting pipe to union of flushing cistern, inlet and overflow pipe, anti-syphonage pipe or stopper, setting the trap in and pan in lime concrete, 150mm minimum thickness and finished just below level of rim of pan to receive floor finishing as in repairs complete all as specified and as directed.

Flushing cistern and flush pipe as required shall be measured and paid for under supply only separately.

Supply only PVC valveless, syphonic action type flushing cistern 10 litres capacity low level, white with inlet, ball valve, float and handle / push button, including brackets complete all as specified and as directed.

Supply only flush pipe of polyethylene of high density, 32mm dia for low level / high level flushing cistern complete all as specified and as directed.

PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

Vitreous china wash basin, white, flat back, size 550mm x 400mm excluding taps, waste fitting, but including brackets and including fixing of the following components viz. pillar taps, waste fittings and union, plugs and chains and connecting upto supply pipes, wastes or traps, screws, plugs, cement mortar and other subsidary materials required for fixing including cutting for and pinning in ends of brackets but exclusive of fixing of supply and waste pipe as in repairs complete all as specified and as directed.

(a) Pillar taps and waste fittings as required shall be measured and paid for under supply only separately.

(b) Supply and waste pipes as required shall be measured and paid for separately.

Supply only pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of bore of pipe 15mm complete all as specified and as directed.

Make shall be of Prayag Cat No. Neptune Series PIS-02 or equivalent of makes listed here-in-after.

Supply only Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed of bore of pipe 15mm (Minimum weight 15mm-110gms) complete all as specified and as directed.

BLANK

Supply only Waste coupling of PTMT (half or full threaded) fixed of bore of pipe 32mm (Minimum weight 32mm-45gms) complete all as specified and as directed.

LDPE pipes, 32mm bore of pipe, of pressure rating 6 kgf/sqcm with polyethylene thread union and check nuts, fixed to walls as in waste pipe in wash basin as in repairs complete all as specified and as directed.

Glass shelf including bracket and fittings, matt finish chromium plated (MCH / Colour CP), fixed to walls with chromium plated brass screws as in repairs complete all as specified and as directed.

Make shall be of Prayag Cat No. BEA-45 or equivalent of makes listed here-in-after.

Stainless steel sink with drainage board, 1mm thick, for kitchen, with plugs, waste pipe, waste fittings, washers, including bedding in cement mortar 1:4 on dwarf walls or fixing on and including cantilever cast iron brackets, connecting union to pipe etc., overall size 915mm x 460mm with bowl size 410mm x 330mm x 200mm (size approximate) as in repairs complete all as specified and as directed.

Make shall be of Prayag Cat No. 1239DM matt finish or equivalent of makes listed here-in-after.

Brass Chromium plated shower rose 100mm size with or without swivel joints, arm including fixing to steel pipe or union complete all as specified and as directed.

Make shall be of Prayag Cat No. Cascade Series BOS-32 (Shower) and BOS-47 (Arm) or equivalent of makes listed here-in-after.

Swivel shower of PTMT any colour for fixing with 15mm pipe including fixing to pipe or union as in repairs (Minimum weight 40gms) complete all as specified and as directed.

Soap dish with holder, brass, chromium plated fixedd to plugs with chromium fixed complete all as specified and as directed.

Make shall be of Prayag Cat No. Angelo Series BA-25G or equivalent of makes listed here-in-after.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of bore 110mm as in repairs complete all as specified and as directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of bore 75mm as in repairs complete all as specified and as directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of bore 75mm as in repairs complete all as specified and as directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of bore 110mm as in repairs complete all as specified and as directed.

PVC (SWR) floor trap, plain with grating of diameter of outlet 75mm including jointing with solvent cement as in repairs complete all as specified and as directed.

PVC (SWR) bend any radius of bore 110mm complete all as specified and as directed.

PVC (SWR) bend any radius of bore 75mm complete all as specified and as directed.

PVC (SWR) vent cowl of bore 110mm complete all as specified and as directed.

PVC (SWR) branch piece, single (single Y) equal or unequal of bore 110mm complete all as specified and as directed.

Stainless steel rack kitchen plate rack size 910mm x 780mm x 250mm, with screws and necessary fittings including making holes to fix to walls as in repairs complete all as specified and as directed.

Make shall be of Prayag Cat No.P-348 or equivalent of makes listed here-in-after.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry at the rate of 3.0kg of cement per square metre complete all as specified and as directed.

Plain cement concrete as in roof kerbs, benching etc.,rounded or chamfered on edges, 1:2:4, type B0, using 12.50mm graded stone aggregate mixed with liquid water proofing compound complete all as specified and as directed.

Supply only liquid water proofing compound shall be measured and paid separately.

Rendering 10mm thick in CM(1:3), mixed with liquid water proofing compound and finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound shall be measured and paid separately.

Supply only Liquid Water proofing compound all as specified and as directed.

Preparing the rendered surface thoroughly to remove all loose particles, dirt / dust particles and applying a uniform coat of blown grade bitumen VG-10 @ 1.20 kg/sqm conforming to IS 702 over a coat of bitumen primer @ 0.40 Litres / Sqm followed by APP membrane reinforced with polyster non woven fabric 3mm thick weighing not less than 3.6 kg / sqm laid on primed surface by forced application followed by a finishing coat of solar reflective aluminium paint @ 0.10 litres / Sqm complete all as specified and as directed. complete all as specified and as directed.

For detailed specifications please refer particular specifications and list of manufacturers given here-in-after and the rate rate quoted shall include for the same.

Plain cement concrete 1:5:10, type E2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

Plain cement concrete, 1:2:4, type B0, using 12.50mm graded stone aggregate, averaging 25mm thick as in levelling course, finished fair and even complete all as specified and as directed.

Rendering 15mm thick in CM(1:3) on fair faces of brickwork or concrete surfaces as in sunken floors mixed with liquid water proofing compound finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound shall be measured and paid separately.

Preparing the rendered surface thoroughly to remove all loose particles, dirt / dust particles and applying a uniform coat of blown grade bitumen VG-10 @ 1.20 kg/sqm conforming to IS 702 over a coat of bitumen primer @ 0.40 Litres / Sqm followed by APP membrane reinforced with polyster non woven fabric 3mm thick weighing not less than 3.6 kg / sqm laid on primed surface by forced application complete all as specified and as directed.

Steel water tubing, medium grade galvanised with all fittings like bends, elbows, reducers, unions, tees etc and fixed complete to walls and ceilings or laid in floor of bore of pipe 25mm in short length as in spouts in sunken floors complete all as specified and as directed.

SCH "A" PART-II (INTERNAL ELECTRIFICATION)

Taking down carefully unserviceable point wiring copper / aluminium (light, fan, socket or power) complete, including removal of batten / conduit / gutties / wooden board etc., including fittings and fixtures such as switches, ceiling roses, regulators, sockets, light fittings, etc., and separating the serviceable items for reuse, removal from site under Sch of credit and removal of unserviceable items out of site and making good the disturbed surfaces of walls, ceilings etc., complete all as specified and as directed.

Taking down carefully unserviceable sub main wiring aluminium conductor cables any number of runs of any cross section complete, including removal of batten / conduit and separating the serviceable items for reuse, removal from site under Sch of credit and removal of unserviceable items out of site and making good the disturbed surfaces of walls, ceilings etc., complete all as specified and as directed.

Point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated 1100 volts grade unsheathed FRLSH cable confirming to IS-694, 1977 with multistranded copper conductor, drawn through and including non-metalic rigid PVC conduit, conduit fittings and conduit accessories not less than 20 mm dia concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc., and including provision of one 1.5 sqmm PVC insulated single core multistranded copper conductor FRLSH green in colour as earth continuity conductor and connected to common earth dolly, including pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet, 60mm deep, concealed in walls, duly painted with two coats of anti-corrosive over a coat of red oxide zinc chrome primer and covered with bakelite hylam sheet cover 3mm thick fixed with cadmium plated screws for housing the switches, socket outlets, fan regulators etc., complete all as specified and as directed for one light point controlled by one switch.

Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

All as per BOQ No.141 here-in-before but for one ceiling fan point controlled by one switch and regulator

Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

All as per BOQ No.141 here-in-before but for one exhaust fan point controlled by one switch.

Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

All as per BOQ No.141 here-in-before but for One bell / buzzer point controlled by one bell push

Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

All as per BOQ No.141 here-in-before but for One switch socket outlet point 3 pin 5 Amps on independent board.

Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

All as per BOQ No.141 here-in-before but for One switch socket outlet point 3 pin 5 Amps on same board with other switches.

Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

All as per BOQ No.141 here-in-before but for point wiring with two 4.0 sqmm single core copper conductor multistranded FRLSH cable and one 4.0 sqmm PVC insulated single core multistranded cable as earth continuity conductor FRLSH green in colour for one 3 pin switch socket outlet, 15 Amps, on independent board complete all as specified and as directed.

Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

Switch piano, flush type single pole, one way, 5 Amps complete all as specified and as directed.

Bell push, flush type, 5 Amps complete all as specified and as directed.

Switch socket combination, flush type, 2 in 1, 3 pin, 5 Amps universal type complete all as specified and as directed.

Switch socket combination, flush type, 2 in 1, 3 pin, 5 Amps and 15 Amps universal type complete all as specified and as directed.

Ceiling rose, 3 terminal, PVC / polycarbonate, insulated body complete as specified and as directed.

Stepped type electronic fan regulator, 300 W, flush type, including fixing on existing laminated sheet complete as specified and as directed.

Bell, ding dong type, AC, 230 Volts, single pole complete all as specified and as directed.

LED batten fitting 20/22 W, 230 V, extruded aluminium housing provided for easy heat dissipation wall mounted complete pre wired and including tube and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting with the following parameters,complete all as specified and as directed.

(a) Make shall be Havells Cat No. LUMILINEPLUSBS20/22WLED865SPCSS or equivalent of makes as listed here-in-after.

(b) For all other mandatory requirements of LED fittings, please refer Particular Specifications given here-in-after.

LED batten fitting 10 W, 230 V, extruded aluminium housing provided for easy heat dissipation wall mounted complete pre wired and including tube and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting with the following parameters,complete all as specified and as directed.

(a) Make shall be Havells Cat No. LUMILINEPLUSBS10WLED865SPCSS or equivalent of makes as listed here-in-after.

(b) For all other mandatory requirements of LED fittings, please refer Particular Specifications given here-in-after.

Surface mounted, LED bulk head fitting, 10W with PDC aluminium housing and milky diffuser, 230 V, pre wired including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire complete all as specified and as directed.

(a) Make shall be C & S Cat No.SIRIUS / 10W or equivalent of makes as listed here-in-after.

(b) For all other mandatory requirements of LED fittings, please refer under Particular Specifications here-in-after.

Taking down existing light fitting including bracket and provision of LED building security light fitting 20W made up of powder coated pressure die cast aluminium SMD LED Street light without lens with heat resistant toughened glass., IP66 protection and impact resistance of IK07, complete pre-wired and connecting up with suitable twin core flexble copper wire including provision of necessary GI tubing medium grade 25mm bore of pipe 1.5m bent to shape with necessary clamps made out of mild steel, nuts and bolts etc., including two coats of synthetic enamel paint over a coat of red oxide primer on exposed steel surface for fixing the fitting to steel tubular poles etc complete all as specified and as directed.

(a) Make shall be as C & S Cat No. INDUS-i/20W under or equivalent of makes as listed here-in-after.

(b) For all other mandatory requirements of LED fittings, please refer under Particular Specifications here-in-after.

Ceiling fan 1200mm sweep, without regulator, high speed, 5 star rating fan, with suitable down rod, AC single phase, 240 Volts, 50 Hz and connecting including provision of two way PVC connectors, 1 sqmm flexible three core multistranded copper conductor cable from ceiling rose or connector to fan complete all as specified and as directed.

Make shall be of Usha Cat No. ENERGIA 32 or equivalent of makes as listed here-in-after.

Exhaust fan, heavy duty, 300mm sweep, 1370 RPM, with louvers, metal body conforming to IS-2312-1967, AC single phase, 240 Volts, 50 Hz and connecting including provision of two way PVC connectors, 1 sqmm flexible three core multistranded copper conductor cable from ceiling rose or connector to fan including earthing and fixing arrangements like making hole in wall and finishing to shape to match adjoining surface and writing MES No.20mm height with synthetic enamel paint black complete all as specified and as directed.

Make shall be of Usha Cat No. AEROCLEAN PLUS 300MM or equivalent of makes as listed here-in-after.

Taking down ceiling fan any sweep, dismantling and opening up, replacing bearings, bushes, condensors of same existing type and capacity, greasing, assembling back, painting of fans complete, with synthetic enamel paint by spraying including filling cavities with filler, coat after cleaning all dust, dirt, grease, rewinding motor etc., testing and writing MES No.20mm height with synthetic enamel paint black and hanging back in position with all accessories and connecting including 1.5 sqmm flexible three core multistranded copper conductor cable from ceiling rose or connector to fan including earthing complete all as specified and as directed.

Supply, installation, testing and commissioning of storage type water heater electric 25 litres capacity, including suitable size connection pipe, hot / cold type, accessories and connecting up complete all as specified and as directed.

Make shall be Havells Cat No. Senzo GHWASESWH025 or equivalent of makes as listed here-in-after.

MCB 6-32 Amps, SP, 240 Volts, 50 Hz, AC supply, "B" curve, with breaking capacity of 10 kA complete all as specified and as directed.

MCB 40 Amps, SPN, 240 Volts, 50 Hz, AC supply, "C" curve with breaking capacity of 10 kA complete all as specified and as directed.

Sheet metal enclosures with socket plug top and MCBs, single pole and neutral with two pin and earth plug and socket complete one single pole MCB 20 Amps, 10 kA, "C" Curve, 240 V complete all as specified and as directed.

MCB DB SPN 8 way, double door, powder coated, 240 volts, AC, 50Hz, IP 43 protected, with provision for MCB double pole as incomer and DP / SP MCBs as outgoing with tinned copper bus bar, neutral link, earth link and connecting up as in repairs complete all as specified and as directed.

The incomer and outgoing MCBs as required shall be measured and paid separately.

Load line MCB DB TPN 4 way, vertical, double door, powder coated, 415 volts, AC, 50Hz, IP 54 protected, fixed on wall semi flush with provision for MCCB FP, 100 Amps as incomer and MCB SP 40 / 63 Amps as outgoing with tinned copper bus bar, neutral link, earth link and connecting up as in repairs complete all as specified and as directed.

The incomer and outgoing MCCBs/MCBs as required shall be measured and paid separately.

MCCB Four Pole, 100 Amps, 415 V, 16 kA, with fixed magnetic and fixed thermal setting complete all as specified and as directed.

MCCB Four Pole, 160 Amps, 415 V, 16 kA, with fixed magnetic and fixed thermal setting complete all as specified and as directed.

Power / Sub-main wiring with PVC insulated unsheathed, 1100 volts, grade multistranded copper conductor, two runs of single core 6 sqmm FRLSH conforming to IS-694, drawn through and including suitable dia rigid PVC conduit, conduit fittings and conduit accessories alongwith one run 6 sqmm PVC insulated single core multistranded copper conductor cable FRLSH (green) as earth continuity conductor concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc. and connecting to common earth dolly complete all as specified and as directed.

(a) Two runs of 6 sqmm cable and one run of 6 sqmm cable and one run of conduit will be measured as one length.

(b) Cutting chases on walls for concealing pipes and cost of terminal box is deemed to be included in the item rates quoted for sub-main wiring / circuit wiring.

Earth continuity conductor or main earthing lead of 4mm dia GI wire fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required as in repairs complete all as specified and as directed.

Taking out existing earthing and provision of Earthing complete with galvanised iron earth plate electrode 600mm X 600mm X 6mm thick, with and including earthing of 4mm dia GI wire protected by 15mm dia GI pipe light grade upto a length of 7.5m. The plate shall be buried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of the earth plate at a depth not less than 1.5 metres below ground level, connected to earth lead as described here-in-before by means of bolts, nuts, washers and checknuts made out of galvanised iron or mild steel, earthing lead protected by as described here-in-before and connected to main switch board or main control board or electric pole all as shown on electrical plate No.3 of MES Sch Part-I including necessary earth work and excavation in any type of soil, plain cement concrete 1:3:6, type C1 chamber, reinforced cement concrete cover slab with locking arrangement and handle of 10mm dia MS round bars 450mm long, 1:2:4 type B1, 50mm thick with 8mm dia TMT bars at 140mm centre to centre both ways, GI pipe of bore 20mm medium grade for watering with funnel, wiremesh, salt, charcoal, lugs including testing complete all as specified and as directed.

M/s Omm Muruga Enterprises

HARI ENTERPRISES