ADDN ALTN TO BLDG NO P-231 41SA RW 12 2024 25 ADDN ALTN TO TOILET BLOCK BLDG NO P-9 41SA RW 10 2024-25 ADDN ALTN TO TOILET BLOCK BLDG NO P74 41SA RW 13/ 2024-25, PROVN OF COVERED PARKING SHED AT SINGLE OFFR

Amount

NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as directed.

Surface excavation not exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Excavation in trenches, not exc. 1.5 m wide and not exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, taking out and laying of cables, laying water tubing, poles, struts/ stay etc. n exc 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft/ loose soil, complete all as specified and directed.

Returning filling in soft/ loose soil, including spreading, levelling, watering and well ramming in layers not exc. 25 cm, complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level not exc. 1.5 m above the starting point, complete all as specified and directed.

Material and labour for, sand filling under floors or in foundations or cushioning for interlocking tiles including watering and consolidation, complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

Material and labour for, hardcore of gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) for holdfast/ bed block, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles, complete all as specified and directed.

Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6), complete all as specified and directed.

Material and labour for, brickwork with sub class ‘B’ bricks, old size brick, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified and directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as required, complete all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

Material and labour for, 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including taking down existing unserbiceable granite, complete all as specified and directed.

Material and labour for,use and waste of wooden formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams, etc., rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surfaces of concrete, complete all as specified and directed.

Supply and fix for, 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); complete all as specified and directed.

Supply and fix for, 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Supply and fix for, solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications & drawing and directed.

Supply and fix for, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, all as per specification & drawing and directed.

Supply and fix for, solid PVC Double door frame of size 50mm x 95mm made out of 5mm single side prelam PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing and directed.

Supply and fiox for, factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing and directed.

Supply and fix for, 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed.

Supply and fix for, extruded aluminium alloy handles, fabricated type, anodised 150mm size, complete all as specified and directed.

Supply and fix for, 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix for, mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

Supply and fix for, 150mm size (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and directed.

Supply and fix for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix in repair for, stainless steel curtain rod 25mm dia with fancy side holders, brackets, complete all as specified and directed.

Supply and fix for, Harrison curtain rails, 20mm dia mild steel, chromium plated with fixing brackets, stops, rollers etc., complete all as specified and directed.

Supply and fix for, mortice lock, vertical type, size 100 mm 4 livers brass, complete all as specified and directed.

Supply and fix for, aluminium door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed

Material and labour for, mild steel flat iron 25x3mm thick as in band, straps, hold fasts etc. and similar small articles conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed.

Supply and fix for, mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Supply and fix for, rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

Material and labour for, mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material and labour for, mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Supply and fix for, pressed steel frames 105 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and fix for, steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

Supply and fix for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fix for, powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per TD drawing No. CESZ/2015/TD/005 dated 05 Jan 2015 and directed.

Supply and fix for, anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. as per TD drawing No.CESZ/2015/TD/005 dated 05 Jan 2015, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Material and labour for, 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed.

Material and labour for, powder coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605mm, including aluminium main / cross tee section of size 35mm x 23mm x 1.5mm (minimum) and aluminium angle 25mm x 23mm x 1.5mm thick, suitable size GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I including providing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface, complete all as specified and directed.

Supply and fix for, Gl frame work for seamlessm ceiling comprising of Gl perimeterm channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurledm web of 50 mm and flange of 26 mm each with lips of 10.5m mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to, centre, complete all as specified and directed.

Mater and labour for, 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately), complete all as specified and directed.

Mater and labour for, 10mm thick plaster of paris ceiling (Gypsum anhydrous) to curved surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately), complete all as specified and directed.

Material and labour for, 100mm thick plain cement concrete (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar (1:6), complete all as specified and directed.

Materials and labour for, glazed ceramic coloured tiles, 450 X 300 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat of cement mortar (1:4), complete all as specified and directed.

Material and labour for, machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade, complete all as specified and directed.

Materials and labour for, rendering 10 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound @3% by weight of cement over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Supply only integral water proofing compound complete all as specified.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of arylic distemper, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of acrylic distemper over a coat of primer over 1mm thick wall care putty, complete all as specified and directed.

Material and labour for, complete removal of existing treatment on wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

Materiala nd labour for, providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over 1.5mm thick wall putty, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying finishing walls with textured exterior paint of required shade (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm over 1mm thick plaster of paris putty over plastered surface to prepare the surface even and smooth, complete all as specified and directed.

Supply and fix for, 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane, complete all as specified and directed.

Supply and fix for, 4mm sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed.

Supply and fix for, 4.0mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane, complete all as specified and directed.

Supply and fix for, solar control film 50 micron reflective type sticked to glass panes as per instructions of manufacturers and complete all as directed.

Material and labour for, preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Supply and fix for, 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for, 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for, bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix in repairs for, bib tap, two way, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore all as per Cat No.ARI-CHR-39041 of make Jaquar or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix for, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

Supply and fix in repair for, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

Supply and fix for, stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for 15mm bore unions, complete all as specified and directed.

Supply and fix in repair for, stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for 15mm bore unions, complete all as specified and directed.

Supply anf fix for, stop valves, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for 15mm bore unions, complete all as specified and directed.

Supply and fix for 15mm bore dia brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks in double layers (cylindrical vertical with closed top) of 1000 litres capacity with ISI marked and all as specified in IS12701, specified in SSR Part I including 20mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash basin, white, flat back, size 550 x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, 32mm dia corrugated PVC waste pipe, chromium plated coupling 32mm dia and cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed.

Supply and fix for, vitreous china wash down water closet pan 'P' or 'S' traps (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash down water closet pan 'P' or 'S' traps (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

Supply and fix for, toilet paper holder, vitreous china, box type fixed to walls with chromium plated (CP) brass screws, complete all as specified and directed.

Supply and fix for, soap dish, vitreous China white, approximate size 160x 160x90mm fixed to plugs with chromium plated brass screws, complete all as specified and directed.

Supply and fix for, liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minimum weight 105gms), complete all as specified and directed.

Supply and fix for, towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms), complete all as specified and directed.

Supply and fix for, towel ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete all as specified and directed.

Supply and fix for, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

Supply and fix in repair for, vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

Supply and fix for, vitreous china urinal partition white of size 310x700 mm, complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 100mm internal dia of pipe, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

Supply and fix for, 110 bore PVC (SWR) bends any radius with access door, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed.

Material and labour for, 100mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1(1:2:4), complete all as specified and directed.

Supply and fix for, PVC (SWR) floor trap 75mm dia, plain with CP grating including jointing with solvent cement, complete all as specified and directed.

Cutting existing 40mm bore steel tubing for alterations or additions (Each cut measured), complete all as specified and directed.

Supply and fix for, 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for 25mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix for, 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Taking down carefully unservoceable copper/ aluminium point wiring (light, fan, bell, socket or power) including all fittings such as switches, ceiling roses, regulators, sockets, switch boxes etc. complete and making good the disturbed surfaces complete all as directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 1.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one light/ ceiling fan/ exhaust fan controlled by one, one way switch, complete all as specified and directed.

Material and labour for point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 1.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one socket outlet 5 pin 6 Amps on independent board, complete all as specified and directed.

Material and labour for point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 1.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one socket outlet 6 Amps on same board, complete all as specified and directed.

Material and labour for point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 4.0 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 4.0 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one socket outlet 5 pin 15/16 Amps on independent board, complete all as specified and directed. Notes for item Nos 94 to 97- : Flush steel terminal box, inner plate and front plates shall be measured and paid sepertely under relevant item.

Supply and fix for, modular metal flush box 3 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 4 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 6 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 8 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 3 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 6 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 4 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 8 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 6A, 1 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 16A, 1 module, complete all as specified and directed.

Supply and fix for, modular socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, modular socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for ceiling rose, surface bakelite 63.5mm x 23.5mm three terminals, complete all as specified and directed.

Supply and fix for, modular fan regulator, step type, 120W - 2 module, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 8 way 200 Amps rated bus bar, double door type, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 12 way 200 Amps rated bus bar, double door type, complete all as specified and directed.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SP 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SPN 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply and fix for, single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole 20 Amps MCB, complete all as specified and directed.

Supply and fix for, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amps MCB, complete all as specified and directed.

Supply and fix for, sub main wiring with two runs of single core 4.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including rigid PVC non metallic surface conduit medium duty (ISI marked) with all accessories such as junction boxs, bends, tees etc. including one run of single core 4.0 Sqmm (nomonal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of conduit shall be measured as one unit length.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including PVC casing & capping medium duty (ISI marked) with all accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of casing & capping shall be measured as one unit length.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including PVC casing & capping medium duty (ISI marked) with all accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nomonal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire including taking down old sub main wiring, complete all as specified and directed. Notes: All runs of copper conductor and one run of casing & capping shall be measured as one unit length.

Supply and fix for LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

Supply and fix for, LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fix for, LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete, complete all as specified and directed.

Supply and fix for, LED street light/ building security light fitting 25 watt 230 volt AC out door type with high pressure die cast aluminium hosing heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection as per Cat No.LSTS-25-CDL-M of make Crompton or equivalent model of make as per PS, complete all as specified and directed.

Supply and fix for, ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 Volt, 1200 mm sweep min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC), complete all as specified and directed.

Supply and fix for, exhaust fan, steel body AC single phase 230V of size 300m sweep with, blades and frame and louvers, complete all as specified and directed.

Supply and fix for, electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., complete all as specified and directed.

Material and labour for, earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.50 metre below normal ground level connected to galvanised steel earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete earth pit in PCC (1:3:6) type C1, 50mm thick pre-cast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) cover slab (Reinforced with 8mm dia TMT bar @15cm centre to centre bothways and suitable handle made of 10mm dia), provision of funnel, wire mesh, 20mm bore galvanised steel tubing (medium grade) for watering, charcoal or coke and salt in alternate layers of 15cm (compacted thickness), 15mm bore galvanised steel tubing (light grade) for protection of earth lead connection, necessary excavation and earth work in any type of soil complete all as specified and indicated on electrical plate No.3 of SSR Part-I (2009) including testing on completion. (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in the unit quoted rate).

Supply, laying, testing commissioning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm, 4 core (conforming to IS-7098 (Part-I)-1988) with suitable size of aluminium lugs, laid in trenches/ duct/ passing through pipe or fixed on pole, complete all as specified and directed.

Supply, laying, testing commissioning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm, 4 core (conforming to IS-7098 (Part-I)-1988) with suitable size of aluminium lugs, laid in trenches/ duct/ passing through pipe or fixed on pole, complete all as specified and directed.

Material and labour for, sand cushioning (dry) in trenches for protection of UG cables (below, above and around the UG cable laid in trenches) of 230mm spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and directed. (NOTE : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for).

Material and labour for, sub class 'B' brick, well burnt, old size, flat, laid breadth-wise along the axis of cable laid in trenches over sand cushion laid for UG cable protection, complete all as specified and directed.

Supply and fix for, 40mm bore tubes, 'light grad', galvanised, with all fitting; laid in trenches,for cable protection under the road/ path/ pole, complete all as specified and directed.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

KAY CEE CO. INDIA (BID ID -3137281)

A M CHOUDHURY AND CO (BID ID -3138268)

MS J B CONSTRUCTION AND CO (BID ID -3139332)

M/S AK SINGH (BID ID -3140805)

M/S GOPAL ROY AND CO (BID ID -3139310)

SUBHAS CONSTRUCTIONS (BID ID -3141285)

M/S DILIP GOSWAMI (BID ID -3140829)