Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

GENERAL ABSTRACT OF COST

Name of Work : Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji

Nagar, New Delhi

Sub Head No. Description DSR NDSR/MR Total

CHAPTER-1 CIVIL & INTERIOR WORK

SH.1 Carriage Of Materials 8,226.00 0.00 8,226.00

SH.3 Reinforced Cement Concrete Work 48,074.00 0.00 48,074.00

SH.10 Repairs To Building 27,018.00 0.00 27,018.00

SH.11 Dismantling And Demolishing 16,985.00 0.00 16,985.00

SH.13 Water Proofing 8,059.00 0.00 8,059.00

SH.14 Other Miscelleneous Works 3,740,950.00 24,726,115.45 28,467,065.45

CHAPTER-2 Furniture & Chairs Work 81,618,161.53 81,618,161.53

CHAPTER-6 ELECTRICAL WORK 4,940,484.00 29,171,529.00 34,112,013.00

CHAPTER-7 FAS & FSS SYSTEM 8,012,513.00 8,012,513.00

CHAPTER-8 NETWORKING & VC SYSTEM 137,111,337.00 137,111,337.00

Total after Adding GST Factor @ 1.0633 on DSR 63,264,383.96 299,182,334.46 362,446,719.00

Digitally signed by AMIT

Digitally signed by AMIT

ABSTRACT OF COST

Name of Work : Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

I.NO DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

SH 1.00 CARRIAGE OF MATERIALS

Note - item to be applicable in urban areas having directions for restricted hours for movement/

plying of load carrying motor vehicle of 3.5 cum or more.

Total Carried Over to Abstract for Sub Head: 1.00 Carriage Of Materials : 8226.00 0

SH 2.00 CONCRETE WORK

CEMENT CONCRETE (CAST IN SITU)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including

attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor

five level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate

20 mm nominal size derived from natural sources)

2.2 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for : sqm 37.50 669.55 25108.00

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and

string courses fillets, kerbs and steps etc.

Total Carried Over to Abstract for Sub Head: 2.00 Concrete Work : 2478363.00 0.00

SH 3.00 REINFORCED CEMENT CONCRETE WORK

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings,

balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above

3.1 5.3 plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and cum 2.03 10719.3 21707.00

reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3

graded stone aggregate 20 mm nominal size derived from natural sources).

3.2 5.9 Centering and shuttering including strutting, propping etc. and removal of form for

A 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 13.50 608.35 8213.00

Digitally signed by AMIT

STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete above plinth level.

A 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 202.50 89.65 18154.00

Total Carried Over to Abstract for Sub Head: 3.00 Reinforced Cement Concrete Work : 48074.00 0.00

SH 4.00 MASONRY WORK

AUTOCLAVED AERATED CEMENT BLOCKS-AAC

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in

super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand

). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course

of masonry work.

Total Carried Over to Abstract for Sub Head: 4.00 Masonry Work : 160034.00 0.00

SH 5.00 CLADDING WORK

Providing and fixing 12 mm thick gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of

5.1 8.2 required size, approved shade, colour and texture laid over 18 mm thick thick BWP ply board, joints

treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,

curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and fixing angle-iron frames for of mild steel sections, joints mitred with necessary welding

at junctions and fixing the frame to wall with steel dash fasteners of 8 mm dia, 75 mm long bolt, and

applying a priming coat of approved steel primer.

A 8.2.2 Granite stone slab colour black, Cherry/Ruby red

(ii) 8.2.2.2 Area of slab over 0.50 sqm sqm 83.07 4425.35 367614

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine

5.2 8.3 polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-

Granite work metre 784.50 418.85 328588

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops

of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform,

5.4 8.5 vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for each 5.00 808.15 4041

pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Digitally signed by AMIT

4 MM THICK DECORATIVE VENEER FACING

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-

5.5 8.28 1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface

A 8.28.1 Decorative veneer facings of approved manufacture sqm 850.00 1645.8 1398930.00

Total Carried Over to Abstract for Sub Head: 5.00 Cladding Work : 2223529.00 0.00

SH 6.00 WOOD WORK

HARD WOOD BACKFRAMING

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with

necessary stainless steel screws etc.

VISION PANEL GLAZING

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters

for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion

inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25

mm to 40 mm thick :

A 9.7.7 Float glass panes

(i) 9.7.7.2 5.0 mm thick glass panels (weight not less than 12.50 kg/sqm). sqm 65.88 2231.2 146991.00

FLUSH DOOR SHUTTER

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative

type, core of block board construction with frame of 1st class hard wood and well matched

commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of

A 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm 302.40 2015.75 609563.00

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of

flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass

excluded) (overall area of door shutter to be measured):

A 9.24.1 Rectangular or square

Extra if louvers (not exceeding 0.2 sqm) are provided in flush door shutters (overall area of door

shutters to be measured).

A 9.25.1 Decorative type door

GYPSUM BOARD PARTITIONS

Digitally signed by AMIT

Poviding and fixing partition upto ceiling height consisting of G.I. frame and required board,

including providing and fixing of frame work made of special section power pressed/ roll form G.I.

sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel

50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the

spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or

suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one

flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor

and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and

nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and

ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame

work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick

having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to

the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5

mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and

direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum

(GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster

board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

HIGH PRESSURE LAMINATED SHEET FACING

Providing & fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/

6.8 9.127 suede finish with high density protective surface layer and reverse side of adhesive bonding quality

conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Digitally signed by AMIT

PLAIN GYPSUM PLASTER BOARD WALL PANELING

Providing and fixing, in position concealed G.I. section for wall paneling using board of required

thickness fixed on the 'W' profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges

of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one

flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm.

6.9 9.133 Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully

threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed

head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge,

the joints of the boards are finished with specially formulated jointing compound and 48mm wide

jointing tape to provide seamless finish.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on

6.10 9.139 back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- each 2.00 7145.9 14292.00

charge, all complete.

COMMERCIAL PLY PLAIN LINING

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of

6.11 9.140 approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of

Engineer-in charge (Frame work shall be paid for separately).

A 9.140.1 12 mm thick commercial ply conforming to IS : 1328 BWR type sqm 1750.00 1084.6 1898050.00

A MR-1 8 mm thick commercial ply conforming to IS : 1328 BWR type sqm 550.00 1063.75 585063.00

A MR-2 4 mm thick commercial ply conforming to IS : 1328 BWR type sqm 650.00 981.50 637975.00

MILD STEEL TUBE FRAME WORK

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube,

placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre

both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at

6.12 9.154 junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm kg 600.00 133.35 80010.00

long bolt, including making provision for opening for doors, windows, electrical conduits, switch

boards etc., including providing with two coats of approved steel primer etc. complete, all as per

direction of Engineer-in-charge.

Digitally signed by AMIT

DOOR FRAME FOR SOLID FIRE RATED WITH VISION PANEL

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm

on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than

120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled

with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I.

6.13 9.161 Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for metre 12.00 1791.05 21493.00

fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size

100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire

resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of

Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

DOOR SHUTTER FOR GLAZED FIRE RATED WITH VISION PANEL

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming

to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-

charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x

60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating

not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing

with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including

applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all

complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

GLAZING FOR VISION PANEL SOLID FIRE RATED DOOR SHUTTER

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I.

beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33

mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c ,

including applying a coat of approved fire resistant primer/ powder coating of not less than 30

micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per

NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required

6.15 9.164 thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and sqm 0.27 39995.8 10799.00

minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of

fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be

tested in approved NABL accredited lab or by any other accreditation body which operates in

accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration

scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or

BACK PLY/ BOARD

Providing and fixing 6mm thick both sides Pre-laminated cement bonded wood particle board as

per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the

backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per

direction of Engineer in-charge.

Digitally signed by AMIT

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side

balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand

6.17 9.168 including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with sqm 90.00 2563.75 230737.50

auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer in-

charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine

6.18 9.169 ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. sqm 270.00 2339.6 631692.00

including necessary nails,screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of

6.19 9.171 approved make/brand to cupboard shutters with full threaded steel screws including making each 120.00 226.75 27210.00

necessary recess in board and finished etc. complete as per direction of Engineer-in-charge

Providing and fixing stainless steel Concealed Hinge Open 180 degrees of approved make/brand to

6.20 MR -3 door shutters with full threaded steel screws including making necessary recess in board and finished each 18.00 257.55 4635.90

etc. complete as per direction of Engineer-in-charge

D TYPE OFFSET PULL HANDLE

Providing and fixing stainless steel Grade 304 Assa Abloy/ Geze/ Dorma TGDI D type Offset Pull

6.21 MR 4 Handle 600 mm long, bar outer dia 25 mm, center to center 600 mm, Back to back fixing with each 122.00 3695.82 450890.51

suitable fixing accessories etc .complete as per direction of Engineer-in-Charge

SLIDE CHANNEL DOOR CLOSER

Providing and fixing Assa Abloy/ Geze/ Dorma TS 70 aluminium extruded section body slide channel

door closer, closing force adjustable size EN 3–4(door weight upto 36 kg to 80 kg and door width

from 701 mm to 1100 mm), tested according to EN 1154 with necessary accessories and screws etc.

Digitally signed by AMIT

MORTISE LOCK WITH EPC FOR TOILET

Providing and fixing Assa Abloy/ Geze/ Dorma 285 WC mortise dead lock having 55-80 mm Backset,

6.24 MR 6 CE certified Approved for fire-rated doors including Strike Plate (best make of approved quality) for each 2.00 1526.05 3052.10

glazed aluminium auoustic doors including necessary cutting and making good etc. complete.

Providing and fixing stainless steel Grade 304 Assa Abloy/ Geze/ Dorma TDLH 8100 Lever Handle with

6.25 MR 7 6501 Roses,6612 Escutcheons,8mm Spindle with Fixing Screws for door thickness 35-55 mm, Back to each 2.00 2476.10 4952.20

back fixing with suitable fixing accessories etc .complete as per direction of Engineer-in-Charge

SS BALL BEARING HINGES

Extra for providing SS ball bearing hinges instead of ISI marked Stainless Steel butt hinges bright

finished of required size with necessary screws. (Shutter area to be measured).

Total Carried Over to Abstract for Sub Head: 6.00 Wood Work : 12472430.00 1709009.29

SH 7.00 FLOORING WORKS

VITRIFIED FLOOR TILES

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved

7.1 11.41 make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),

jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and

matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of

7.2 11.48 organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including

filling / grouting and finishing complete as per direction of Engineer-in-charge.

GRANITE STONE FLOORING

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as

well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand)

laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of

matching shade including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :

A 11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. sqm 1500.00 2589.9 3884850.00

Digitally signed by AMIT

RAISED/FALSE ACCESS FLOORING

Providing and fixing removable raised/false access flooring with system and its components of

approved make for different plenum height with possible height adjustment upto 50 mm, comprising

7.4 11.54 of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I.

Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by

Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of

thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size

100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check

nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head

in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate

using epoxy based adhesive of approved make or the machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size

570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head

using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the

pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid,

rigid support for access floor panel, the system shall provide a minimum clear uninterrupted

clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as

per the architectural drawings, as specified and as directed by the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static

high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded

construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top

and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together

(minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist

epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with

Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound.

The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp

technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel

is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in

the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly

Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge. All

specification must be printed on the side of the panel to ensure the quality of the product

A 11.54.2 450 mm Finished Floor Height (FFH). sqm 138.00 5407.15 746187.00

Digitally signed by AMIT

Deduct for not grouting the joints with white cement and matching

pigment in the items of fixing of vitrified tiles

WOODEN FLOORING

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws

complete with :

a 11.33.1 Second class teak wood sqm 70.00 4187.95 293157.00

ITALIAN MARBLE STONE FLOORING

Providing and laying machine cut, mirror polished Marble stone flooring,

in required design (Simple geometrical, abstract etc.) and in patterns in

combination with Italian marble stones of different colours, shades and

finished surface texture etc., in linear portions of the building, all complete

as per the architectural drawings, with 18 mm thick stone slab laid over

20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including

pointing with white cement slurry admixed with pigment to match the

marble shade, including rubbing, curing and polishing etc. all complete

as specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona,

Fire Red or Dark Emperadore etc.

Providing and laying of 2mm conductive Vinyl rolls as specified and indicated. The cost to include

preparing surface to receive vinyl flooring requirements like the floor to be absolutely leveled, hard,

dried, even and free from dirt, grease, moisture , and fixed using required adhesive ( water based

adhesives like Arobond 44 of Colourbond mktg/VC 31 of Pidilite Ind. ) and correct laying technique.

The make of vinyl flooring shall be of Armstrong or equivalent of which the specs / samples have to

be submitted for approval.

Flammability : B1 Class

Sound Absorption : 3 dB

Sheet width/length : 180/16-25 cm/m

Tile side length : 60.8/60.8 cm/cm

Total wt : 2.9 kg/m2

Colour fastness : 6 stage

Electrostatic loading limit : <2 Kv

MR 11 Thermal resistance : 0.010 m2K/W sqm 65.00 2365.75 153773.75

Total Carried Over to Abstract for Sub Head: 7.00 Flooring Works : 21899045.00 153773.75

Digitally signed by AMIT

SH 8.00 ROOFING WORKS

PLAIN GYPSUM BOARD CEILING

Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

8.1 12.45 hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of

angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm

centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia

x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre,

with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling

section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but excluding the cost of painting

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with

BIS certification marks)

GI METAL GRID CEILING

Digitally signed by AMIT

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal

level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @

120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get

required length and of size 24x32 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200

mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200

mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to

8.2 12.52 be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of

size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required

cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed

to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised

butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T,

bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all

complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5

mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides

inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction

Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum),

including factory painted after bending and perforation, and backed with a black Glass fiber

acoustical fleece.

ROCK WOOL THERMAL INSULATION

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having

density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel

plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of

Engineer in- Charge.

Total Carried Over to Abstract for Sub Head: 8.00 Roofing Works : 3800086.00 0.00

SH 9.00 FINISHING

INTERIOR FINISHING

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the

surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall

Digitally signed by AMIT

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per

manufacturers specifications :

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer

applied @ 0.75 ltr /10 sqm

LIGHTWEIGHT GYPSUM PLASTER

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight

plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming

9.4 13.78 to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ sqm 1800.00 363.45 654210.00

RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc.

MELAMINE CLEAR POLISH

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden

shade texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and

2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to

remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface

is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat

to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further

allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and

melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface

is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is

applied with compressor pressure spray gun using melamine clear polish and melamine thinner

mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be

done in 1 or 2 layers without gap of time.)

9.6 GYPSUM BOARD LINING

Providing and fixing of plain gypsum plaster board conforming to IS: 2095 Part - 1:2011 (Board with

BIS certification marks) to existing dry partition using metal to metal flat head screws, including

jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle

beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board

as per manufacture's specification and direction of engineer in charge all complete..

12.5 mm thick fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3

(Board with BIS certification marks)

Digitally signed by AMIT

12.5 mm thick tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011

(Board with BIS certification marks)

9.7 COMMERCIAL PLY PLAIN LINING

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of

. approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of

Engineer-in charge (Frame work shall be paid for separately).

9mm thick Decorative plywood one side decorative veneer and commercial veneer on other face

(Type 1) conforming to IS 1328 BWR Type

9.8 TOUGHENED GLASS 10 MM THICKNESS

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with

. EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions

of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

A MR-13B Toughened glass 10 mm thickness sqm 40.00 3123.35 124934.00

9.9 5.5 MM THICK MIRROR FACING

Providing & fixing silvered glass mirror confirming to IS 3438: 1994 with flat polished edge , to MDF

. base backing with neutral silicone and/or double-sided adhesive pads etc. complete( MDF base

backing included in costing).

9.10 6 MM THICK LACQUERED FACING

Providing & fixing 6 mm thick annealed SCG Planilaque Evolution (premium GRIHA rated lacquered

glass i.e. textured from saint gobin) with flat polished edge fixed to 5.5 mm thick plain MDF board

backing with neutral silicone and/or double-sided adhesive pads etc. ,including polishing/MTG all

complete as per the drawing & directions of engineer-in-charge.

9.11 WALL PAPER FACING

Providing & fixing fabric backing commercial grade wall paper of approved shade to MDF/Gypsum

board/POP Punning base backing which have 100% washable, scratch resistance, peel proof, and

MR 16 fire retardant properties, including preparation on the punned surface for receiving the wall paper, sqm 175.00 4934.85 863598.75

adhesive as per the manufacturer specification, all complete as per the drawing & directions of

engineer-in-charge( Base backing to be paid separately).

9.14 MR 17 ARTIFICIAL GRASS sqm 50.00 5476.00 273800.00

Digitally signed by AMIT

Artificial Vertical Green Wall Plant Panels of SIZE 40cm x 60cm, 40cm x 90cm, 50cm x 50cm,

Installation is done on Waterproof ply board with staple gun machine. PATTERNS as per approved

9.15 ROLLER BLINDS

Supplying and fixing Roller Blinds to the following specifications , Fabric shade as approved,

sunscreen, dense basket weave 3% openness factor. Operation: - Manual. Offset side-mounted

metal chain operated Mounting: Pocket mounted. Shade Orientation: Regular roll, shade cloth falls

at window side of roller. Configuration: Single band AVERAGE LENGTH OF BLIND is 2.0 M to 2.5 M. The

fabric to be Fire Retardent certified.

9.16 BLACKOUT ROLLER BLINDS

. Supplying and fixing of Blackout blinds to the following specs.

Black-out material fibre-glass coated fabric, 12 mils thick, 62 threads per sq in., 0.750 lbs per sq in.

(441g per sq mt.)

Operation: - Manual. Offset side-mounted metal chain operated

Mounting: Closure Box in metal

Shade Orientation: Regular roll, shade cloth falls at window side of roller

Configuration: Single band

The Fabric to be as per approved sample (Fabric should be Fire Retardent Certified).

Cellular Semi Opaque 100% Polyester Hardware SpecificationHeadRail: Head rail is 17 mm high and

47 mm wide, Thickness 1.00 mm. It is made up of powder coated high strength aluminum alloy

covered by two end caps made up of PVC.Drum & Cradle: They are molded ABS components with

high strength metalic drum which are meant for controlling the lifting cord.Bottom Rail: This is

Aluminum Extruded Rail Made up of High Strength Aluminum alloy, Which is powder coated in

A MR 19 white.Installation Bracket: It is made up of mild steel with zinc plate.Bottom Rail End Cap: It made up SQM 79.44 4161.00 330549.84

of high strength ABS.White Cord: It is made of Nylon braided non stretchable thread of 1.2 mm

thickness.PVC Slip : It is made up of high strength PVC of width 25 mm.Fabric: 100% spun bonded

non‐woven polyester translucent fabric Pleat dimension 3⁄4” hexagonal cell with a distinct air

pockets Sanitized, Weight : 145 + 5% GSM, Thickness : 0.14 ‐0.17, colour fastness of light – 4‐5 Grade (

DIN EN ISO105‐B02).

9.17 MR 20 Providing & fixing Motor Mechanism nos 7.00 25615.00 179305.00

9.18 MR 21 Providing & fixing Motor Remote 16 channel nos 7.00 18377.00 128639.00

9.20 3M & EQUIVALENT SCOTCHCAL FROSTED CRYSTAL

Digitally signed by AMIT

Providing & Fixing 3M & equivalent Frosted Translucent, cast PVC, self-adhesive vinyl, special

CRYSTAL-effect film to reproduce Sand-blasting effect on glass with customized designs, thickness of

2 mil (0.05mm) without adhesive & 3M & equivalentil (0.8)with adhesive having minimum tensile

strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4

pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct

sunlight) to 15yrs (indoors) must be endorsed by 3M & equivalent India Limited Architectural Market

Department. Code 7725 - 324.

Application - DECORATIVE/PRIVACY FILM ON GLASS

Electronically/computer plotter cut. Applied on glass and other rigid, clear substrates. (partitions,

doors, windows etc.) Available in 5 colours

9.21 3M & EQUIVALENT SCOTCH PRINT CONTROLTAC & COMPLY WALL GRAPHICS

Providing & Fixing Digitally reproduced 3M & equivalent Scotch print decorative graphics on IJ180C

(with controltac & comply feature for direct, bubble-free application on walls) with UV protective

matte over laminate 8520 with a polyethylene-coated paper liner. Customized imagery & the

thickness of 2 mil (0.05mm) without adhesive & 3-4mil (0.8-0.10mm) with adhesive, having minimum

tensile strength of 5 pounds/inch at 73°F (0.9 kg/cm at 23°C ). the adhesive should be Pressure

activated, position able, with air release channels. MCS warranty of 5yrs must be endorsed by 3M &

equivalent India Limited Architectural Market Department.

MR 23 Application - WALL MURAL-Directly pasted on POP finish wall Conformable & durable decorative Sqm 60.00 2610.00 156600.00

graphics directly applied on walls, ceilings, elevator doors, partitions, pillars, aluminum cladding

etc.Note : Cost of approved image included.

Supplying and fixing of Room Signages in imp.aluminum profile with 3 mm acrylic Gents/Ladies

pictograph printed on canvas (Room Names) - Include braile letterings Size is 6"x10".

Rest Room - Include braile letterings

9.23 MR 25 Supplying and fixing of Restroom Signages in imp.aluminum profile with 3 mm acrylic Gents Nos 22.00 799.00 17578.00

pictograph printed on canvas (Room Names) - Include braile letterings Size is 6"x10".

9.24 MR 26 Fire Exit ID - 4mm thk. Acrylic base with autoglow vinyl cut letters. 14"x8".Include braile letterings Nos 1.00 644.00 644.00

Digitally signed by AMIT

Fire Extinguisher Signage -Providing and fixing graphical Triangular signage for fire extinguisher.

signage to be made of 3M & equivalentm thick foam board with edge to edge self adhesive self-

luminescent Forex or equivalent vinyl stuck on it. Fix Green vinyl to cover Forex vinyl leaving 6mm

border around edges with 'FIRE EXTINGUISHER' letters cut-out. (Note : 'FIRE EXTINGUISHER' letters to be

self-luminescent and not the background). 'FIRE EXTINGUISHER' letters height shall be 100mm in HT.

9.26 MR 28 Advisory / notice signage - 4mm thk. Acrylic base with autoglow vinyl cut letters. 19"x8" Nos 6.00 810.00 4860.00

9.27 MR 29 Providing and fixing SS PUSH/PULL signage for all doors. Size 2"x 6" Nos 16.00 541.00 8656.00

9.28 EVACUATION MAP

Providing and fixing evacuation maps of size A3 size, signage shall be made of 3M & equivalentm

thk foam board on to which on to which evacuation plans printed on coated paper shall be stuck.

The signage shall be laminated including the edges. (Note: soft copy of the signage shall be

provided by architect). signage shall be fixed with 3M & equivalent double sided adhesive tape. A3

IN CASE OF FIRE USE STAIRS' photo luminescent sign size: 10"x10"mm I sign aluminum profile with 3M &

equivalentm acrylic

Total Carried Over to Abstract for Sub Head: 9.00 Finishing : 2474533.00 8314256.75

SH 10.00 REPAIRS TO BUILDING

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including

cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with

white cement based polymer modified self curing mortar, including disposal of rubbish, all

complete as per the direction of Engineer-In-Charge.

Total Carried Over to Abstract for Sub Head: 10.00 Repairs To Building : 27018.00 0.00

SH 11.00 DISMANTLING AND DEMOLISHING

Demolishing brick work manually/ by mechanical means including stacking of serviceable material

and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

A 15.7.4 In cement mortar cum 10.00 1698.45 16985.00

Total Carried Over to Abstract for Sub Head: 11.00 Dismantling And Demolishing : 16985.00 0.00

SH 12.00 ALUMINIUM WORK

ALUMINIUM FRAMING

Digitally signed by AMIT

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built

up standard tubular sections/ appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

A 21.1.1 For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)

12.2 DEMOUNTABLE DOUBLE GLAZED ACOUSTIC PARTITION

Providing and fixing, in position demountable double glazed acoustic aluminium framed partition

system of appropriate size and thickness (not less than 2 mm) having sound reduction value >35 Db,

supporting height upto 2700mm with snap on option for installating glass, , the aluminium quality as

per grade 6063 T5 or T6 as per BS 1474, including anodising up to 15-20 microns of required colour

and shade, accessories ie 'T' section, corner section & vertical "I" section between glass to glass

. ,glass packing to adjust the floor level, ceiling profile, floor profile and wall profile as per the

manufacturer specification( The item includes cost of material such as cleats, sleeves, screws etc.

necessary for fabrication of extruded aluminium frame work. Item includes necessary aluminium

frame work to recve 35 mm thick flush door mounting. Nothing extra shall be paid on this account,

all complete as per the architectural drawings and approved shop drawings , & directions of

engineer-in-charge.

100 mm overall thickness 25 mm visible face partition with 10 mm thick double skin clear toughened

glass with double sided adhesive tapes for glass to glass butt joints

Total Carried Over to Abstract for Sub Head: 12.00 Aluminium Work : 43395.00 435164.00

SH 13.00 WATER PROOFING

INTEGRAL CEMENT BASED TREATMENT

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @

0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound

@ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48

Digitally signed by AMIT

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of

pipes and masonry with polymer mixed slurry.

Total Carried Over to Abstract for Sub Head: 13.00 Water Proofing : 8059.00 0.00

SH 14.00 Other Miscelleneous works

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved

texture, design and pattern. The tiles should have Humidity Resistance (RH) of 95-99%, Light

Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt -

6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron

section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length

3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size

15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using

galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash

fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster

of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.

The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of

size19x19X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl

plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of

all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for

all heights. The work shall be carried out as per specifications, drawings and as per directions of the

engineer-in-charge.

A 26.27.1 With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6 sqm 100.00 2069.9 206990.00

B 26.27.2 With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) sqm 602.00 2362.1 1421984.00

14.2 MINERAL FIBRE FALSE CEILING

Digitally signed by AMIT

Providing and fixing mineral fibre false ceiling tiles at all heights of size 300X1200mm of approved

texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance

? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7),

suitable for Green Building application, with Recycled content of >35% in true horizontal level

suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick

(galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size

15x32mm of length 1200 mm to form grid module of size 300x1200 mm suspended from ceiling using

galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash

fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster

of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on

periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of

0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre

& 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling

support system shall be pre-painted with polyester baked paint, for all heights. The work shall be

carried out as per specifications, drawings and as per directions of the engineer-in-charge.

A MR 33 With 15 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.9) sqm 162.00 3719.75 602599.50

14.3 WOODEN PERFORATED CEILING

Providing and fixing Wooden Acoustic false ceiling tiles at all heights of size 595X595mm of approved

texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance

? 85%, in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized

iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of

length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of

size 15x32 mm of length 600 mm to form Wooden Acoustic Ceiling Tiles of size 600x600 mm

suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm

outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length

and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.

The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of

size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl

plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of

all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for

all heights. The work shall be carried out as per specifications, drawings and as per directions of the

engineer-in-charge.

A MR 34 With 15 mm thick Wooden Acoustic false ceiling tile sqm 200.00 8738.80 1747760.00

Digitally signed by AMIT

Providing & fixing acoustic panels any size and shape in approved color and code no. with

Standard size & 25mm thickness. acoustic Panels should have Sound Absorption coefficient (NRC)

0.94. Formaldehyde emission standards of GB18580-2001 class E1, it is a green material with asbestos-

free, non-toxic and tasteless gas under extreme temperature, protecting the ozone layer, non-irritant

and recyclable. acoustic panels have to be Fire-resistant . Good insulation properties, to prevent

transmitting the heat from outdoor to indoor directly as partition or and ceiling, saving 35% of

energy, extending the life of air conditioning. acoustic panels are Light weight and allow free cutting

with paper knife.

14.5 MR 36 STRETCH FABRIC CEILING sqm 10.00 4934.85 49348.50

PVC STRECH FALSE CEILING - TRANSLUCENT

Providing and Fixing Custom made PVC Stretch false ceiling to fit exact dimensions with aluminium

supports. The PVCc ceiling must be stretched and hooked into aluminium rails. Stretch aluminum rails

ensuring good rigidity, to be fixed to the walls or other supports at the specified level. A properitory

semi rigid PVC Anchor ( for Tension mounting ) is welded on the outer periphery of the PVC ceiling.

Following are the Technical Specification :

Ceiling Material : Stretchable PVC with PVC Harpoon welded

Thickness : 0.17mm +- 10%

Dimensional Stability : -5 deg to +45 deg C ( No visisble deformation)

Weight : (200 +_ 15 ) g / sqm

Water Vapor permeability :

For Hydrometric degree > 65% RH = 0.0045 g / hr sqm mm Hg

Very effective impermeable barrier to water

Water proof / Dust Proof / Airtight

Resistant to water , dampness, sea water, copper salt solutions and x-rays

Thermal Cofficient : 0.16 kcal/m H C

Fire Classification : B-s2-d0 acc. With DIN EN 14716

Low Emission : CLASS A+ Certified

14.6 METAL BAFFLE CEILING

Digitally signed by AMIT

Providing and fixing extruded aluminium Baffle Ceiling System false ceiling at all heights of approved

texture, design and pattern. The baffle fixed with aluminiumn end cap at terminals and intermediate

connector piece at joints in true horizontal level suspended on interlocking Grid of hot dipped all

round galvanized iron section of 0.8mm thick (galvanized @120 gsm) comprising of main Baffle

carrier of 23X34mm 0.5mm thick of length 3000 mm, suspended from ceiling using galvanized mild

steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter

fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm,

spaced at 1200 mm centre to centre along main ‘Baffle carrier’.The work shall be carried out as per

specifications, drawings and as per directions of the engineer-in-charge.

Note: All support carriers to be powder coated with approved color

30mm wide 100 mm high 1.2mm thick powder coated aluminium at 150mm center to center

(Sample of Full length baffle to be get apporved prior to installation)

Providing & Fixing of Wooden 1200x600 mm, finished Suspended Ceiling System with Woodworks

Microlook edge tiles with 15mm Suprafine 43 exposed grid.

The Tile in 6mm perforations with approved laminate (Portland Maple, Sea Beech, Siam Wood &

Mystique Walnut or as approved) finish would have an NRC of 0.42, Humidity Resistance (RH) of 70%

in module size of 600mm x 1200mm x 15mm and density of 650 Kgs/M3.

The grid should be of “approved” make with 15mm wide T - section flanges color white/black

16.7 MR 38 having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a sqm 102.00 8369.00 853638.00

web height of 43mm and a load carrying capacity of 15.5 Kgs/M2. The T Sections have a

Galvanizing of 90 grams per M2 and pullout strength of 100kg. Suspension system for grid to be of

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood

particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial

ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain

rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet

with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl

plugs 75 mm long etc. all complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

16.9 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold

fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood cum 11.89 131576.95 1564713.00

Digitally signed by AMIT

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm

dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm

dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per

direction of Engineer-in-charge.

Providing and fixing Judges Table made of 19mm thick both side balancing lamination factory

pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah,

16.7 MR 39 cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of sqm 368.00 2339.6 860972.80

Engineer-in-charge.

Providing & fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/

suede finish with high density protective surface layer and reverse side of adhesive bonding quality

16.7.1 conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Advocates & clerk Tables

Providing and fixing Advocates & clerk Tables made of 19mm thick both side balancing lamination

factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks,

16.8 MR 39 almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction sqm 419.38 2462.70 1032807.13

of Engineer-in-charge.

Providing & fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/

suede finish with high density protective surface layer and reverse side of adhesive bonding quality

16.8.1 conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm

16.9 9.112 fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre- metre 1800.00 85.6 154080.00

laminated particle board as per direction of Engineer-in-charge.

16.10 Providing and fixing of 2 Hours Fire rated doors

MR 41 SIZE :1200 x 2400mm - Single leaf Sqm 5.76 43500 250560.00

Door Jamb: 100 x 80mm GI Fire Rated door frame

Shutter: 40mm thick GI fire rated door finished with approved fire rated paint / powder coated as

Vision Panel: 450 x 200 mm vision panel formed out of Fire rated glass with approved beading

Digitally signed by AMIT

The Doors shall have 6mm thk clear glass of St. Gobain/Pilkington- Pyroshield Make or any other

equivalent with beading. The Fire Doors are to be fully insulated and have been tested as per IS:

3809-1979, ISO: 834-1975, IS: 3614 (PART-II)- 1992 and BS 476 (PART- 20 & 22)- 1987 under live fire

conditions from Central Building Research Institute (CBRI), Roorkee, National Test House Calcutta for

Stability, Integrity and Insulation for 2 Hrs. The glass is to comply with both BS 476: PART 22 and BS

6206 relating to fire resistant and impact performance.

Finalized vendor to submit the Test certificates for the above.

Hinges provided are to be Stainless steel double ball bearing butt hinges of size 100mm x 76mm x

3mm thick conforming to BS 7352 standard for ‘Strength and durability performance of metal hinges

for side hanging applications and dimensional requirements for template drilled hinges’ and are

classified in class 8 i.e., with 20000 annual operations. The screws for hinges are SS 304 grade Philips

head CSK screws of size M6x 15mm. Latching shall be Mortise lock with independent escutcheon. D

pull handles of SS shall be provided.

Hardware : as per manufacturers standards

Hinges - 4 nos Fire rated Hinges

Lockset - as per manufacturers standards

Door Handle: Fire rated Door handle as per manufacturer's standards

Door Closer: Surface mounted Fire rated Door Closer

Door Stopper: Fire rated Door stopper

Seals: Fire Seals as applicable

Security System :Provision shall be made for Magnetic Access Control

Supply of NATURAL MOSS BREATHING PANLES . Each panel is 5 x 5 x 6 cm and weighs 30 g. The panel

is a high-class sound absorber made from natural, hand-picked Moss. The panel element is designed

16.11 MR 42 to cover large surface areas with maximum flexibility in shape and design. Each Pixel element retains sqm 15 10009 150135.00

its colors, is fire-proof, absorbs & releases humidity to remain soft, and is completely maintenance-

free. Per sqm requires 400 pxl

Digitally signed by AMIT

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one

side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of

approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen

cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade),

calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives

(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw

withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/ mm2,

modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property

of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel

piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded

star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel

piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

16.13 Veneer ceiling

Providing and fixing Veneer finished ceiling feature made of 19mm commercial board and all

exposed surfaces finished in 4mm thick veneer of approved shade including framing, all fixing

MR 43 hardware, accessories, making cove, cutout for light fixtures and any other incidentals which may Sqm. 75 7802.00 585150

require to secure to false ceiling and to accomplish the work in all respect as per detail drawings

and as directed & approved by architect.

Rate quoted to include vertical drops, making cove and all cut-outs required for light fixtures and

other services cut-outs and necessary supports with hitech rods from the true ceiling complete as

directed by Architect. BR of Veneer 100/-

Providing & fixing of mineral Fibre Grid Ceiling of size 600x600 with high density / fire resistant Mineral

wool acoustical Ceiling tiles tegular edge of 19mm thick Sound Absorption (NRC) Up to 0.80 Sound

16.14 MR 44 Blocking (CAC) 35 Articulation Class (AC) 170 with light reflectance 87% USDA certified. Sqm. 150 3796.00 569400

Digitally signed by AMIT

Material: Perforated plasterboard 600x600 strato panel cieling

Board Type: Acoustic gypsum panel

Dimensions: <1200 x 2000 or 1200 x 2500> x 12.5mm

Weight: 8.00-9.30 kg/m²

Perforation: Round 8, 15 and 20mm holes (random)

Perforation percent: 9.9%

Surface: Unpainted cardboard

Backside: Black acoustic fleece (white on request)

Fire rating: A2-s1,d0 in accordance with EN 13501-1

Indoor climate: Degasification 10 days

Particle emission: Low

Air purification: Cleaneo technology

Supply, Installation, Testing and Commissioning of Automatic hand dryer of best quality, to be

operated with 230 volts, single phase, with fully hygienic condition, with all accessories including

16.15 cutting and making good the walls, wherever required. near the wash area fixing with necessary

a MR 45 Mystair - ED05 / Euronics Nos 15 5891.00 88365

Providing and fixing ABS Auto aerosol Dispenser, fixed to wooden cleats with C.P brass screws,

complete including cutting and making good the walls wherever required.

a MR 46 UTEC : UT-630 / Euronics Nos 15 2488.00 37320

16.17 ARTIFACTS

MR 47 Digital printing of canvas along with framing and boarding of the canvas including installation and Sqm 27 23000.00 621000

RESTORATION OF PATTCHITRA ARTWORK

MR 48 pattchitra 12' x 5'including artist honorarium , paints , brushes , surface coating and protective Sqm 21 43000.00 903000

ARTWORK ON THE FIRE ESCAPE DOORS

Doors 1.2m x 2.1m along with door jam cover and moulding handcrafted polished with fixing PCS 9 75000.00 675000

including the one that needs to be restored including artwork on the door with artist

iii MR 49 honorarium,paints,brushes,surface coating and protective coating including transportation .

Including artist honorarium , paints , brushes , surface coating and protective coating .

DESIGNER CEILING

Digitally signed by AMIT

MR 50 False ceiling approx along with the GI metal frame work finished with the plasterboard along with SQM 50 22316 1115800

ornate cornice finished in paint . Artwork on the ceiling depicting rich cultural heritage of India

vi either directly on the ceiling or suspended digitly printed artwork .

MR 51 BACKEND GLASS FAÇADE mix of all screens for glazing foldable in digital printing or fabric motifs of SQM 40 40227 1609080

different states , handcrafted glass, jaali and stone cared mural work

Preparation of complete set of shop drawings including finishing, MEP services, details, design % 1 358,858,137.42 3588581.00

calcualtions etc. and any other details as and when desired by Engineer In charge /client. A

vii qualified professsional for the purpose shall be appointed after due appproval from Engineer In

16.18 Laminated Wall Panelling

Providing and fixing woodworks on pre laminated bord of 15mm or higher, made of planks of height

MR 52 195mm, length 2440mm, to be installed on aluminium keel with help of inside clips. The grooves on Sqm. 746.007 5500 4103038.5

the planks to be irregular pattern.

Total Carried Over to Abstract for Sub Head: 14.00 Other Miscelleneous Works : 3740950.00 24726115.45

Digitally signed by AMIT

ABSTRACT OF COST: FURNITURE

AMOUNT Indicative Image UNIT QTY RATE AMOUNT

1.00 Manufacturing, providing and placing in position machine made factory assembled President and Vice Presidnet

Table of approved make following dimensions with the following specifications.

Providing and fixing President and Vice Presidnet Table Cabin Table Table :Main Table of size: 2900W1 x 2300W 2 x

900D/600D x 740/600Hmm and back free standing storage of size: 3000W x 400Dx 2000Hmm ,whose top is made of

40-50mm thick Veneer MDF E-1(Environmental Friendly)with Edge banding (PVC) 2mm. E1 grade Veneer MDF with

zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality.

This should comply with (EN 120-1992). The wiring tray is made of steel sheet thickness 1.2mm. Epoxy powder coated

spray color, baked at temperature 200 C°.Raceways contain the horizontal cable channel that fitted with a modesty

panel tidily and effectively. The understructure is made of 40-50mm thick Veneer MDF Grade E-1(Environmental

Friendly), cover Edge banding (PVC) 2mm. E1 grade Veneer MDF with zero urea formaldehyde emissions (<or=

8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992).

The Aluminium flipper is made from anodised aluminuim with soft closure. The modesty panel(wherever required) is

made of 25-30 mm thick Veneer MDF (E1-Grade) with 2mm PVC edge banding and Brackets used are 3.2 mm Powder

Coated Steel of 80-90 microns.Complete as per the direction of Engineer-in-charge. Product should be BIFMA gold

rated SCSglobal certified for inhouse air quality .Side/Back storage: Side Storage is combination of drawer plus swing

door & open shelf ,Body of storages made out 19 mm thick Veneer MDF (E-1 Grade) with 2 mm PVC edge-banding. E1

grade Veneer MDF to be used which provide no urea formaldehyde emission and formaldehyde should be phenol

base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality.

This should comply with (EN 120-1992).The storage should have extruded aluminum handle, as per requirement.

Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged

doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.

Product should be BIFMA gold rated SCSglobal certified for inhouse air quality .

Manufacturing, providing and Placing High Back revolving chairs for President and Vide President Cabin of

approved make of following dimensions with the following specifications.

Providing and placing High Back chairs for President and Vide President Cabin. The seat shall be made up of 12mm

thick hot pressed plywood & upholstered with leatherite and moulded medium density foam. Overall dimensions of

Chair shall be, Width of Chair - 640mm, Depth of Chair - 645mm, Height of Chair-1185-1245mm as measured till

pedestal . The back shall be designed with contoured lumber support for extra comfort. Size of back shall be W-

510+10m, H-715mm & size of seat shall be W-520+10 mm x D-450mm x H-473-533mm. Medium density foam should

be used in making seat & back which shall be moulded with density 45kg/m ³ and hardness load 16kgf. The seat and

back should be arrested together with spine made of 8mm thick HR steel and should be powder coated in black with

40-60 micron . The fixed armrest are made of aluminuim with PU padded. The mechanism of the chair shall have

following features : 360 degree swivel type, Knee Tilt mechanism, Seat & back tilting ration of 1: 1.5, Front pivot for

tilt with feet resting on ground ensuring more comfort, multiple locking position. Gas lift allows 10mm of height

adjustment. The pedestal shall be made of die-cast aluminium base. it shall be fitted with 5 nos twin wheel castor.

The size of the pedestal shall be 670mm pitch-centre-dia 700-720mm with castors). The twin wheel castors shall be

made of Nylon injection moulded in black color. Product should be BIFMA gold rated SCSglobal certified for inhouse

air quality and with 05 Years warranty.

Digitally signed by AMIT

Manufacturing, providing and Placing Mid Back revolving chairs for President and Vide President Cabin of

approved make of following dimensions with the following specifications.

Providing and placing Mid Back chairs forPresident and Vide President Cabin. The seat shall be made up of 12mm

thick hot pressed plywood & upholstered with Leatherite and moulded medium density foam. Overall dimensions of

Chair shall be, Width of Chair - 640mm, Depth of Chair - 620mm, Height of Chair-1000-1065mm as measured till

pedestal . The back shall be designed with contoured lumber support for extra comfort. Size of back shall be W-

490+10m, H-530mm & size of seat shall be W-500+10 mm x D-450mm x H-470-530mm. Medium density foam should

be used in making seat & back which shall be moulded with density 45kg/m ³ and hardness load 16kgf. The seat and

back should be arrested together with spine made of 8mm thick HR steel and should be powder coated in black with

40-60 micron . The fixed armrest are made of aluminuim with PU padded. The mechanism of the chair shall have

following features : 360 degree swivel type, Knee Tilt mechanism, Seat & back tilting ration of 1: 1.5, Front pivot for

tilt with feet resting on ground ensuring more comfort, multiple locking position. Gas lift allows 10mm of height

adjustment. The pedestal shall be made of die-cast aluminium base. it shall be fitted with 5 nos twin wheel castor.

The size of the pedestal shall be 670mm pitch-centre-dia 700-720mm with castors). The twin wheel castors shall be

made of Nylon injection moulded in black color. Product should be BIFMA gold rated SCSglobal certified for inhouse

air quality and with 05 years warranty.

Digitally signed by AMIT

4 Manufacturing, providing and Placing Sofa for all Cabin of approved make of following dimensions with the

following specifications.

Providing & Placing sofa, Wooden structure of sofa to be fabricated using good quiality hardwood duly seasoned and

applying anti-termite paint of approved brand & manufacture to ensure stability of the frame, On the wooden base

frame of the sofa to be provided with M.S. helical spring, sides & back with jute strips, with polyfill covered with jute

& finished with thick marking cloth before doing final finished with leathrite have basic cost not less than 1000/- Pet

Mt. Seat - 40-45Kg/cum density PU Foam, 100mm thick, Back - 35-40Kg/cum density PU foam, 60mm thick, Sides

(inside) - 40-45 Kg/cum density PU Foam, 45 mm thick Sides (outside) & back (back side) - 35-40 Kgcum density PU

foam, 25mm thick. Seat shall rest on SS square frame of size 25mm x 25mm supported solid wooden section of height

150-220mm. All SS work should be in grade 304. Base of sofa should be infilled with suitable woode sections so as to

give proper support to the seat. Height of the base of sofa shall be 150-220mm(approx). Finished width of arm shall

be 100mm after upholstery work. Sofa to be fully upholstered using approved leatherite of A grade of desired shade

duly embossed including providing & fixing of all other related materials including hardwares etc. complete as

directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air

quality.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

4.10 1 seater sofa overall dimension - 820mm W x 780-820mm D x 780-820mm H Nos. 4.0 52,628 210,512

4.20 3 seater sofa overall dimension - 1950mm W x 780-820mm D x 780-820mm H Nos. 5.0 130,390 651,950

5 Manufacturing, providing and Placing Center & Corner Table for Cabin & Waiting Area of approved make of

following dimensions with the following specifications.

5.10 Providing and fixing tables of Centre table Size - 1100mm W x 500mm D x 365mm H for whose top is made of Particle

board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1

grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for

better in-house quality. This should comply with (EN 120-1992).The understructure is made of SS BASE. Product

should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty

5.20 Providing and fixing tables of Side table Size - 450mm W x 450mm D x 365mm H for whose top is made of Particle

board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1

grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for

better in-house quality. This should comply with (EN 120-1992).The understructure is made of SS BASE.Product

should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Digitally signed by AMIT

6.00 Manufacturing, providing and Placing Meeting Table of approved make of following dimensions with the

following specifications.

Providing and fixing rectangular meeting table, Worktop Made of 25mm thick E-1 grade particle board finished with

2mm ABS edge banding. E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-

perforated method) for better in- house air quality. This should comply with (EN 120-1992). The exposed edge of

worktop shall be secured with 2mm thick PVC edge banding tape of approved colour. The height of Worktop shall be

740-760 mm from ground level. The particle board should be E-1 Grade with pvc edge banding. Understructure: MS

understructure with Loop legs made up of 2mm thick metal of dimension 50mm x 50mm epoxy powder 80-90

microns coated spray color, baked at temperature 200c, well supported with beams under table top. Completely

conseled MS wiremanagement and trays epoxy powder 80-90 microns coated spray color, baked at temperature

200c. Wire management: Completely conseled wiremanagement with Aluminium anodized flipper with soft closure.

wiring tray & beams Made from MS sheet 2 mm., flange structure epoxy powder 80-90 microns coated spray color,

baked at temperature 200c with vertical wire uptake from floor via middle leg having removable cover one side and

wire seperator for data and wire seperation, segregates to hozizontal cable tray below fipper,Product should be

BIFMA gold rated SCSglobal certified for inhouse air quality.

6.10 Meeting table 2800mm x 1200mm x 740mm Nos. 1.0 81,125 81,125

6.20 Meeting table 1500mm x 900mm x 740mm Nos. 1.0 50,303 50,303

6.30 Meeting Table 4500mm x 1500mm x 740mm Nos. 1.0 168,374 168,374

6.40 Round Meeting Table of dia 1200mm x 740mm Nos. 1.0 37,194 37,194

Digitally signed by AMIT

7.00 Manufacturing, providing and placing in position machine made factory assembled Cabin Tableof approved make

of following dimensions with the following specifications. Nos. 16.0 418,529 6,696,472

Providing & Placing Cabin Table with side unit with following details and specification :-Table is of Size: 2200mm(L1) x

2350mm(L2) x 900mm(D1) x 600mm(D2)x 740-760mm(H1)/600-640mm(H2). whose top is made of 40-50mm thick

Veneer MDF E- 1(Environmental Friendly), Edge banding (PVC) 2mm. E1 grade Veneer MDF with zero urea

formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should

comply with (EN 120-1992). The wiring tray is made of steel sheet thickness 1.2mm. Epoxy powder coated spray color,

baked at temperature 200 C°.Raceways contain the horizontal cable channel that fitted with a modesty panel tidily

and effectively. The understructure is made of 40-50mm thick Veneer MDF Grade E-1(Environmental Friendly), cover

Edge banding (PVC) 2mm. E1 grade Veneer MDF with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry

board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The Aluminium flipper

is made from anodised aluminuim with soft closure. The modesty panel(wherever required) is made of 25-30 mm

thick Veneer MDF (E1- Grade) with 2mm PVC edge banding and Brackets used are 3.2 mm Powder Coated Steel of 80-

90 microns.Side Combo Storage: Combination of Drawer plus shutter & open Shelf.Body of storages made out 19 mm

thick Veneer MDF (E-1 Grade) with 2 mm PVC edge-banding. E1 grade Veneer MDF to be used which provide no urea

formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g

oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). The storage

should have extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers.

Door Lock should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided

with Hinge-damping mechanism to enable soft closing of doors. Product should be BIFMA gold rated SCSglobal

certified for inhouse air quality and with 5 years warranty.

8.00 Manufacturing, providing and Placing High Back revolving chairs for Cabin Main Chair of approved make of

following dimensions with the following specifications. Nos. 16.0 54,558 872,936

Digitally signed by AMIT

Providing and placing High Back chairs for Cabin. Chair seat made up of insert moulded Polyurethane Foam

upholstered with foam laminated mesh fabric, insert moulded foam assembled over a load bearing plastic seat cover,

back is made up of two piece injection moulded frame, inner frame upholstered with mesh fabric and mounted on

the main assembly, back adjustable lumbar support for achieving comfortable seating posture, seat size 44.5 - 52.5

cm depth (approx.), 46.4 - 51.0 cm width (approx.), sub assembly back size 55.5 cm- 62 cm height. (approx.), effective

back height from Seat - 57 cm (approx.), polyurethane foam for seat having density 65±4 kg/m3, armrest top

injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest, armrest

height adjustable up to 4.5 cm (approx) in 3 steps & width movement adjustable, 360 degree revolving type.

mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position

locking with antishock feature, pneumatic height adjustment of 8.5 cm spine bracket made of aluminum die cast

piece connecting to back with mechanism, pedestal made of die cast alunimium fitted with 5 nos. twin wheel castors

(castor wheel dia. 6.0 cm approx.), base pedestal dia 65.0cm (approx.) and pitch center dia. 71.0 cm with castors,

twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification, approved sample

and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality

and with 05 years warranty.

Manufacturing, providing and Placing Mid Back revolving chairs for Cabin Mid Back Visitor of approved make of

following dimensions with the following specifications.

Providing and placing Mid Back chairs for Cabin. Chair seat made up of insert moulded Polyurethane Foam

upholstered with foam laminated mesh fabric, insert moulded foam assembled over a load bearing plastic seat cover,

back is made up of two piece injection moulded frame, inner frame upholstered with mesh fabric and mounted on

the main assembly, back adjustable lumbar support for achieving comfortable seating posture, seat size 44.5 - 52.5

cm depth (approx.), 46.4 - 51.0 cm width (approx.), sub assembly back size 55.5 cm- 62 cm height. (approx.), effective

back height from Seat - 57 cm (approx.), polyurethane foam for seat having density 65±4 kg/m3, armrest top

injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest, armrest

height adjustable up to 4.5 cm (approx) in 3 steps & width movement adjustable, 360 degree revolving type.

mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position

locking with antishock feature, pneumatic height adjustment of 8.5 cm spine bracket made of aluminum die cast

piece connecting to back with mechanism, pedestal made of die cast alunimium fitted with 5 nos. twin wheel castors

(castor wheel dia. 6.0 cm approx.), base pedestal dia 65.0cm (approx.) and pitch center dia. 71.0 cm with castors,

twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification, approved sample

and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality

10 Manufacturing,

and with 05 years warranty.and Placing Wooden Sofas for all Cabin (as per finally approved sample by department)

of following dimensions with the following specifications.

Providing, making and installing in position ornamental design, customized wooden sofa of approved design

with seat & back upholstery work. The Sofa legs, arms, seat frame & back rest shall be made with first class

teak wood in approved section, shape & size. Upholstery on the seat and back with 12, 25 ,50 mm (required as

per approved design) U foam of Sleepwell or other make as approved by Engineer-in- charge. The cost shall

Include Jute, elastic niwar, blue cut nails, tingles, cardboard, thread roll adhesive etc. as per requirements.

Covering the seat and back with approved fabric stitched in required design as per approved sample. Finally

finishing with high quality water based P.U polish in desired colored & shade. All complete as per full

satisfaction and direction of the Engineer In charge.

Digitally signed by AMIT

11 Manufacturing, providing and placing in position machine made factory assembled Cabin Tableof approved make

of following dimensions with the following specifications.

Providing & Placing Cabin Table with side Table & mobile pedestal with following details and specification ,whose top

and legs are made of 25mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mm PVC edge-

banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated

method) for better in-house quality. This should comply with (EN 120-1992). The Modesty is Particle board wood

Grade E-1 (Environmental Friendly) thicness 16 mm cover with Melamine Edge-Banding(PVC) 2 mm. Also legs are

made of Particle board wood Grade E-1 (Environmental Friendly) thicness 25 mm, cover with Melamine. Drawer Unit :

3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x

600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80

micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each

pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra

stability.Low Height Back Storage : Body of storages made out 18 mm thick Particle Board (E-1 Grade), melamine 0

finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission

and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated

method) for better in-house quality. This should comply with (EN 120-1992). Front of Medium height Storages should

be made out of 16 mm thick Particle Board (E-1 Grade),melamine finishes with 2 mm. PVC edge-banding fitted with

extruded aluminum handle, as per requirement. Storages should be provided with adjustable levelers. Door Lock

should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-

damping mechanism to enable soft closing of doors. Product should be BIFMA gold rated SCSglobal certified for

inhouse air quality and with 05 years warranty.

11.10 Main Desk 1800mm x 750mm x 740mm, Return/Side Table : 1050mm x 450mm x 740mm, Back Swing Door Storage:

11.20 Main Desk 1500mm x 750mm x 740mm, Return/Side Table : 1050mm x 450mm x 740mm, Back Swing Door Storage:

11.30 Main Desk 1350mm x 750mm x 740mm, Return/Side Table : 1050mm x 450mm x 740mm, Back Swing Door Storage:

Main Desk 1200mm x 600mm x 740mm, Return/Side Table :900mm x 450mm x 740mm

Main Desk 1500mm x 750mm x 740mm, Return/Side Table: 1350mm x 450mm x 740mm

Main Desk 1800mm x 750mm x 740mm, Return/Side Table: 1050mm x 450mm x 740mm

11.70 Main Desk 1350mm x 750mm x 740mm Nos. 2 38,574 77,148

Manufacturing, providing and Placing High Back revolving chairs for Cabin High Back of approved make of

following dimensions with the following specifications.

Providing and placing High Back chairs for Cabins. Chair seat made up of insert moulded Polyurethane Foam

upholstered with foam laminated mesh fabric, insert moulded foam assembled over a load bearing plastic seat cover,

back is made up of two piece injection moulded frame, inner frame upholstered with mesh fabric and mounted on

the main assembly, back adjustable lumbar support for achieving comfortable seating posture, seat size 44.5 - 52.5

cm depth (approx.), 46.4 - 51.0 cm width (approx.), sub assembly back size 55.5 cm- 62 cm height. (approx.), effective

back height from Seat - 57 cm (approx.), polyurethane foam for seat having density 65±4 kg/m3, armrest top

injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest, armrest

height adjustable up to 4.5 cm (approx) in 3 steps & width movement adjustable, 360 degree revolving type.

mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position

locking with antishock feature, pneumatic height adjustment of 8.5 cm spine bracket made of aluminum die cast

piece connecting to back with mechanism, pedestal made of die cast alunimium fitted with 5 nos. twin wheel castors

(castor wheel dia. 6.0 cm approx.), base pedestal dia 65.0cm (approx.) and pitch center dia. 71.0 cm with castors,

twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification, approved sample

and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality

and with 05 years warranty.

Digitally signed by AMIT

13.00 Manufacturing, providing and Placing mid Back revolving chairs for workstations/Cabin Visitor & Meeting Room

Mid Back of approved make of following dimensions with the following specifications. Nos. 176.0 27,699 4,875,080

Providing and placing Mid Back chairs for workstations/Cabin Visitor & Meeting Room. Chair seat made up of insert

moulded Polyurethane Foam upholstered with foam laminated mesh fabric, insert moulded foam assembled over a

load bearing plastic seat cover, back is made up of two piece injection moulded frame, inner frame upholstered with

mesh fabric and mounted on the main assembly, back adjustable lumbar support for achieving comfortable seating

posture, seat size 44.5 - 52.5 cm depth (approx.), 46.4 - 51.0 cm width (approx.), sub assembly back size 55.5 cm- 62

cm height. (approx.), effective back height from Seat - 57 cm (approx.), polyurethane foam for seat having density

65±4 kg/m3, armrest top injection moulded in polyurethane and mounted on the injection moulded height adjustable

type armrest, armrest height adjustable up to 4.5 cm (approx) in 3 steps & width movement adjustable, 360 degree

revolving type. mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for

back in 3position locking with antishock feature, pneumatic height adjustment of 8.5 cm spine bracket made of

aluminum die cast piece connecting to back with mechanism, pedestal made of die cast alunimium fitted with 5 nos.

twin wheel castors (castor wheel dia. 6.0 cm approx.), base pedestal dia 65.0cm (approx.) and pitch center dia. 71.0

cm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per manufacturers specification,

approved sample and direction of Engineer-in-Charge. Product should be BIFMA gold rated SCSglobal certified for

inhouse air quality and with 05 years warranty.

14 Manufacturing, providing and placing in position machine made factory assembled workstation of approved make

of following dimensions with the following specifications.

Frame Work, Partition and Cable management : Frame work shall consist of main spine and return spine of aluminium

extruded section of minimum thickness of 1.2 mm. The overall thinkness of Panel base System should be minimum 60-

70 mm. The panel will be hollow inside to accommodate wiring for electrical/data and outer frame of panel should be

made of extruded aluminium.The panel shall be made up of 3 mm thick MDF both sides of the wooden frame to

create the hollow for the wire management.Finishes of panel above the worktop: Above the top fabric pinup+ Glass

writable marker board with raceway on main spine. The hollow panel made of MDF and 3mm thick foam which is

upholstered with 0.5mm thick fabric with half fabric pinup + half glass marker board. The thickness of main spine

partition panel should be minimum 60-70 mm & minimum 25-28mmmm thick for return & Aisle spine.Finishes of

main spine panel below the worktop: Below the top the hollow panel should be made of MDF tile and 0.5mm thick

steel sheet pasted on MDF which is powder coated with EPC finish 80-90 microns for durability on the inside as well

on the outside.The panel outer aluminium frame is designed such a way that it can be easily slide in to the columns/

Connectors by means of stacking one over the other.Horizontal race way should be 150-170 mm height aluminium

profile. There shall be complete cable management arrangement with openable raceway above/ below worktop with

provision for fitting electrical/data switches and holes for passing cable.

Connectors/ Post Description:

End Post: Aluminium 60-70 mm width – 1200-1250 mm height.

Two way post: Aluminium 30-80 mm width – 1200-1250 mm height.

Three way post: Aluminium 30-80 mm width – 1200-1250 mm height.

Four way post: Aluminium 30-80 mm width – 1200-1250 mm height.

Table top supported with 50-60mm width steel bracket.

Table top to table top connector: 150-170 mm Width x 120-140 mm Depth width connector.

Worktop :Worktop Made of 25mm thick E-1 grade particle board finished with 2mm ABS edge banding. E1 grade

laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-

house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm 0

thick PVC edge banding tape of approved colour. The height of Worktop shall be 740-760 mm from ground level. The

particle board should be E-1 Grade with pvc edge banding.

14.10 Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-

480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated

with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310

mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to

provide extra stability. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

years warranty.

Digitally signed by AMIT

Linear Workstation - 1200mm x 600mm x 740mm(Worktop Height) x 1200-1250 mm (Height of panel from Ground)

15.00 L Shape Workstation - 1500mm (W1) x 1350mm (W2) x 600mm D x 740mm(Worktop Height) x 1200-1250 mm

(Height of panel from Ground)

Manufacturing, providing and Placing Medium height Storages of make of approved makeof following dimensions

with the following specifications.

16.00 Providing & Placing of Medium Height Storage of size: 900mm W x 450mm D x 1200mm H, Body of storages made out

18 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be

used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not

more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with

(EN 120-1992). Front of Medium height Storages should be made out of 16 mm thick Particle Board (E-1

Grade),melamine finishes with 2 mm. PVC edge-banding fitted with extruded aluminum handle, as per requirement.

Storages should be provided with adjustable levelers. Door Lock should be of three-way lock mechanism, the hinged

doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.

Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

16.10 Manufacturing, providing and Placing Court Room Table of approved make of following dimensions with the

following specifications.

16.20 Providing & Placing of Court Room Tables: Work top shall be made of 38mm thick particle board interior grade (4mm

Veneer with Melamine Polish and ABS lipping) of approved shade conforming to relevant IS code and equivalent BS

and CIDB norms. Bottom shall have a backing laminate of minimum 0.6 mm thickness. The front edge of work surface

shall be provided with machine pressed 2 mm thick ABS lipping glued with hot melt EVA glue. For any of above type of

Work surfaces- Non-working edges of the work surface shall be provided with machine pressed 0.5 mm thick ABS

lipping glued with hot melt EVA glue. Under structure: Legs are made up of 38mm thick Pre laminated (4mm Veneer

with Melamine Polish and ABS lipping) particle board interior grade of approved shade conforming to relevant IS code

and equivalent BS and CIDB norms.Side return with Storage: Side return Storage (1Drawer+2 Shelve with Shutter) and

its top shall be made of 25mm thick Pre laminated (4mm Veener with Melamine Polish) particle board interior grade

of approved shade conforming to relevant IS code and equivalent BS and CIDB norms. Inside faces shall have a

backing laminate of minimum 0.6 mm thickness. All Visible edges shall of machine pressed 2 mm thick ABS lipping

glued with hot melt EVA glue and non visible edges shall be provided with machine pressed 0.5 mm thick ABS lipping

glued with hot melt EVA glue. Wire management: Completely concealed wire management with vertical wire uptake

from floor via middle leg having removable cover one side and wire separator for data and wire separation,

segregates to horizontal cable tray below flipper including provision of all Electrical Switch, Socket, Flap out Cover,

accessories completes satisfying to Electrical/LV/AV requirement and as per direction of engineer/employer.

16.30 Court Room Table of size 3000mm x 750mmx 740mm Nos. 1.0 2,411,818 2,411,818

16.40 Court Room Table 4400mm x 750mm x 740mm Nos. 6.0 347,274 2,083,644

16.50 Court Room Table of size 14000mm x 800mm x 740mm Nos. 2.0 341,743 683,487

17.00 Court Room Table of size 2100mm x 750mm x 740mm Nos. 40.0 85,585 3,423,416

Table 2200mm x 600mm x 740mm

Providing and placing in position Customized Higback Revolving Chair for Judges Room (as per finally approved

sample by department) of following dimensions with the following specifications.

Digitally signed by AMIT

Providing, making and installing in position ornamental design, customized wooden Chair (for Judge) of size: 650-

680W x 580-610D x seating height is 460mm & over all Height is 1100-1220mm, with seat & back upholstery work as

per approved design and sample.The chair legs, arms, seat frame & back rest shall be made with Superior class

teak wood in approved section, shape and size. Upholstery the seat and back with 12 ,25, 50mm (required as per

approved design) U foam of make Sleepwell or other make as approved by Engineer-in-charge. The cost shall

Include Jute, elastic niwar, blue cut nails, tingles, cardboard, thread roll adhesive etc. as per requirements.

Covered the seat and back with approved fabric stitched in required design as per approved sample.Finally finished

with high quality water base P.U polish in desired colored & shade.All complete as per ful satisfaction and

direction of the Engineer Incharge.

Providing and placing in position Customized midback non revolving Chair for Court Room (as per finally approved

sample by department) of following dimensions with the following specifications.

Providing, making and installing in position ornamental design, customized wooden conference chair

(Court Room) of size: 650-680W x 580-610D x seating height is 460mm & over all Height is 1000-1120mm of

approved design with seat & back upholstery work. The chair legs, arms, seat frame & back rest shall be made

with Superior class teak wood in approved section, shape and size and upholstery the seat and back with 12, 25,

50 mm (required as per approved design) U foam of Sleepwell or other make as approved in Engineer-in-

Charge.The cost shall Include Jute, elastic niwar, blue cut nails, tingles, cardboard, thread roll adhesive etc. as

per requirements. Covering the seat and back with approved fabric stitched in required design as per approved

sample. Finally finishing with high quality water based P.U polish in desired colored & shade all complete as per

full satisfaction and direction of the Engineer In charge.

Manufacturing, providing and placing in position machine made factory assembled waiting Chair of approved

make of following dimensions with the following specifications.

19.10 Cross beam shall be made up of black powder coated rectangular M.S.ERW tube having 8 ± 0.03 cm x 4 ± 0.03 cm x

0.2 ± 0.014 cm size. Leg and armrest shall be chrome plated made of cold rolled steel with 0.12 ± 0.013 cm thickness.

Seat back shell shall be 1.6 mm thick powder-coated perforated shell made from cold rolled M.S. sheet 0.14 ± 0.013

em thicknesses. The Side Bar shall be made of Chrome plated solid steel 3 ± 0.03 cm x 1.2 ± 0.3 cm (DIN174) with

fluting and plastic inserts. The Shell shall be assembled on the Cross Beam with help of M8 Bolts (Per Seat- 8 nos. Seat

to Bracket and 4nos. Bracket to Cross Beam). The seat & back cushion shall be made up of 12mm PU foam and

upholstered with 0.8 mm thick & 535 GSM leatherette over 12mm plywood.

19.20 2 Seater Waiting Chair : 1180 W x 710/480D x 770/400mm Nos. 5.0 47,790 238,950

3 Seater Waiting Chair : 1665 W x 710/480D x 770/400mm

20 Manufacturing, providing and placing in position machine made factory assembled Café Table of approved make

of following dimensions with the following specifications.

Providing and placing Cafe table, Worktop shall be made out of 25mm thick E-1 grade (Environmental Friendly)

particle board cover with laminate and all the edges of worktop shall be provided with machine pressed 1.5-2 mm

thick ABS edge banding glued with hot melt EVA glue. E1 grade laminate with zero urea formaldehyde emissions (<or=

8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-

1992).The understructure is made of 2mm thick Steel square pipe dimension 50 X 50 mm with Epoxy powder coated

spray paint, baked at temperature 200 C° coated of 70-80 micron thickness. Powder coating should be scratch

resistance (cross hatch test 6x6 grid method). Product should be BIFMA gold rated SCSglobal certified for inhouse air

quality and with 5 years warranty.

20.1 Café Table - 600mm x 600mm x 740mm Nos. 3 17,971 53,914

21.0 Manufacturing, providing and Placing Café Chair of make of of approved make of following dimensions with the

following specifications.

Providing and placing in position Cafe Chair.The seat and back & Understructure (legs) are made up injection molded

high impact strength polypropylene polymer (PP) compound with indoor grade UV Resistance. Leveller are made of

high impact strength polypropylene polymer compound with indoor grad UV Resistance and pressed fitted with

tubular frame.Overall size: 540W x 470D x 810-850Hmm. Product should be BIFMA gold rated SCSglobal certified for

inhouse air quality and with 05 years warranty.

22 Manufacturing, providing and Placing Hospital Bed of approved make of following dimensions with the following

specifications.

Digitally signed by AMIT

Overall Sizes (L)1957mm X (W)625 mm X (H)808. It has gas-lift assisted head rest with continuous adjustment from 0°

to 30°.The design focuses on ease of operation, hygiene, doctor and patient ergonomics, and

aesthetics.Homogeneous soft forms with rounded edges evoke feeling of comfort and safety. Lying surface overall

dimension 625 mmx 65 mm,Mattress and Upholstery is to be made with PU moulded foam with density 50-55, 23

mm thick. Mattress is to be projecting out from the under structure to provide soft touch from all sides. Seamless

upholstery is to be provided to avoid spread of bacteria Head rest overall dimension is 625 mm x 497 mm made of PU

moulded foam with 50 -55 density and 23 mm thick.Under structure is to be made of MS square tubes with unique

styling that provides better strength and stability. It is to be provided to reduce the visual clutter and offers better

access and reach. BP Apparatus tray: CRCA sheet construction with SS handle and SS hinge Dia 10 for handle. Sheet

thickness 1.2 ,0.8 and 0.6. swivel tray is to be designed for BP Apparatus that should be concealed when not in use SS

Handle: SS 202 Dia 10 - Aesthetically designed handles are placed in such a way that to give a unique look also provide

wider space for griping to users.Ergonomics: Increased width of the table (625mm) to give better comfort for patients.

Optimized height (808mm) of the table for comfortable observation and reach. Tapered shape is to be provided to

give a unique look and better access for doctor. L-shape leg is to be provided for better stability.Single Step stool is to

be made of ERW square tube.Textured and Rubber mat is to be provided, of 20mm X 20mm size. Tube 1.2 mm thick

and mat 3.0 mm thick Size:485(L) x 335 (W) X 210 (H) Step stool is to be made of MS square tubes, is to be strong and

firm. Top is to be made of textured rubber offering firm grip for climbingThere should be a ss 304 ERW tube of 12.7

mm dia and 1.2mm thick is to be provided at the back of the back rest section to mount tissue roll which should be

used as tissue roll holder.Powder coating is to be Bacteriostatic and thermosetting epoxy polyester,formulated to fulfil

the requirements for bacterial protection. Maximum patient load is to be 135 kg. Head Rest is to be adjustable 0 -

30°.BP Apparatus tray is to be provided to Swivel angle 0 to 180 deg. Approx.To ensure qood quality welding " Co2

Argon" process should be adhered to. All metal components should be pre treated with zinc phosphate in 9 tank

process and then powder coated with anti microbial epoxy polyester powder coating to fulfil the requirements for

bacterial protection.goods should be supplied inknocked down construction to reduce carbon emission. proof loading

test , cycle tests , impacttest.The manufacturer should compliant with ISO 9001, 14001, OHSAS 1800 and CE

23 Manufacturing, providing and Placing Compactor of make ofof approved make of following dimensions with the

following specifications.

Supplying and fixing in position Mobile Storage wherein each body should be of dimensions

(915mm(W)x450mm(D)x1980mm(H) of following configuration and specification consisting of One no.Fixed Single

one side openable Unit & One, one end single openable mobile unit & between the Main Fixed unit & end mobile unit

having single/ double side mobile unit. The System shall be modular & movable type(Knock Down) with 4-5 loading

levels. Each Shelves loading capacity should be 50-55 kg. Each unit shall be connected from the End back with the

Dust proof arrangement with the help of Tong and Groove system arrangement . Handle shall be made of ABS in

round type with Dia of 350mm minimum with a safety lock System at the Centre. channel of the compactor shall be U

– Channels formation to carry more weight and to get more rigidity. Mechanical arrangement shall be concealed

inside the System, only handle shall be installed at the outer Sheet of the Compactor as Shown in the Drawing. The

component specification shall be as follows. channel U - Section: Section shall be minimum 1.0mm thk. Material

Thickness : 0.8mm; Under Carriage Frame - HR sheet 2.5mm thick. channel Post: U - Shaped Post. Wheel: Iron die

casting with anti-rust coating, Loading : 950-1000kg/Wheel There shall be central locking system with wire, handle

lock, Rail lock Plate & Rail Lock assembly in the chain box cover. The material used for the system shall be as per

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji

Nagar, New Delhi

S. No. DESCRIPTION DSR AMOUNT

1 SUB HEAD - II - (PIPING, VALVES AND ACCESSORIES) 1406075.00 600900.00

2 SUB HEAD - III- (HYDRANTS SYSTEM) - 29275.00

3 SUB HEAD - IV - (FIRE EXTINGUISHERS) - 104538.00

TOTAL (DSR+NSR) 2140788.00

Digitally signed by AMIT

SCHEDULE OF QUANTITY -FIRE FIGHTING

Description Of Items Unit Qty Rate (Rs.) Amount (Rs.)

SUB HEAD - II - (PIPING AND ACCESSORIES)

Providing, laying, testing & commissioning of 'C' class heavy duty

MS pipe conforming to IS 3589/IS 1239 including Welding, fittings

like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing

the pipe on the wall/ceiling with suitable clamp/support frame

painting with two or more coats of synthetic enamel paint of

required shade complete as required : (The Welding shall not be

done for piping less than 50 mm dia.)

Providing, fixing, testing & commissioning of 15mm dia quartzoid

2 18.21 bulb type sprinklers of rating 68 degree centigrade with required

2.1 18.21.1 Pendent Sprinkler Each 400 522 208800.00

MR-1 Supplying, installation, testing & commissioning of sprinkler

flexible pipe (UL Listed) of stainless steel complete with 15

NPT on reducer thread with maximum working pressure of 175

PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm

NPT male thread to sprinkler head (Outlet) 15mm NPT female

thread with reducer, nipple, 2 side brackets, center bracket,

stockbar of following sizes complete as required.

MR-2 Providing, installation, testing & commissioning of adjustable

4 rosette plate for 15mm dia in white finish UL Listed or FM approved Each 400 307.00 122800.00

complete as required.

TOTAL CARRIED TO SUMMARY (DSR ITEMS) 1406075.00

TOTAL CARRIED TO SUMMARY (MR ITEMS) 600900.00

Providing two coats of synthetic enamel paint of approved shade

over a coat of primer. Prior to application of primer the surface

5 MR-3 should be cleaned for any dirt, rusts, rough substance etc.

Including painting of legends both direction arrow as per the

approval of the Project Manager.

Digitally signed by AMIT

Description Of Items Unit Qty Rate (Rs.) Amount (Rs.)

TOTAL CARRIED TO SUMMARY (MR ITEMS) 29275.00

SUB HEAD - IV - (FIRE EXTINGUISHERS)

Providing and fixing fire extinguisher of carbon dioxide type

consisting of brand new high pressure steel cylinder bearing IS:

7285 mark and having the approval of controller of explosives

Nagpur, wheel type valve bearing IS:3224 mark internal discharge

tube, 1 meter long high pressure discharge hose, non conducting

horn, suspension bracket, fully charged bearing IS: making fixed to

wall as directed conforming IS : 15683:2006

6.1 4.5kg capacity cylinder Each 6 12952.00 77712

Providing and fixing ISI marked portable fire extinguishers of the

following type.

7.1 Dry Chemical Powder ABC type of 6 Kg as per IS:15683 Each 6 4471.00 26826

TOTAL CARRIED TO SUMMARY 104538.00

Digitally signed by AMIT

ABSTRACT OF COST

S.N. DSR'22 DESCRIPTION UNIT QTY. RATE AMOUNT DSR NDSR

1 NS Air Cooled Precision AC Packaged Unit

Supply, installation, testing & commissioning of double skinned Air

Cooled Package Units of 600 CFM / Ton with COP in complinace to

grren building code, floor discharge type complete with fan section

with dynamically balanced plug type fan with EC motor of IE3

grade with auto speed variation, electronic humdifier, heaters,

externally equalised electronic expansion valve, pre filters, fire

retardent double canvass connection, multi row deep DX copper

cooling coil all of which shall be contained within the cabinet of

The unit should have one independent refrigeration circuits with

refrigerant R-134a / R-410 / R-407C, manual reset HP and an

auto reset LP switch, filter drier and charging port. a thermal

expansion valve, sight glass and filter drier shall be provided for

each circuit. The outdoor unit shall have condenser copper coil,

fixed scroll compressor with variable refrigerant volume or flow

technology, condenser fans with motor of IE-3 grade and drive etc.

The standard controls shall be of microprocessor based

programmable PID logic controller with dew point logic. The

capacity of units are given below which is based on ambient

temperature of 35.0 Deg. C and inside condition of 20+/-2 Deg. C

with RH of 50+/-5%. Precision AC unit shall have provision of inbuilt

The cost ofoperation

BMSgrouped together.

interface card for

integration with BMS System.

1.1 5.5 TR Actual Capacity (1W+1S) - For Server Room including stand for 3610962

indoor and outdoor units.

2.0 Cassette AC Units for Cafeteria

Supply, Installation, testing and commissioning of Air Cooled type

Ceiling Cassette Air-Conditioning unit, each comprising of an

outdoor unit and a single slim indoor unit. Outdoor condensing unit

shall comprise of rotary/reciprocating compressor with first charge of

refrigerent gas & air cooled condenser with fan. Evaporating unit

shall consist of a blower section with dynamically balanced

centrifugal blower driven by TEFC squirrel cage induction motor,

multirows deep copper cooling coil with aluminium fins,

thermostatic expansion valve etc. The evaporating unit shall be

equipped with synthetic fibre filters, insulated drain pan, safety

controls, thermostat, including stand for outdoor units. all complete

The units shall be suitable for 230V±6%,50 Hz, or 415V±10%, 50 Hz.

Digitally signed by AMIT 246496

3.0 Refrigerent Piping

Providing and Fixing of interconnecting Refrigerent Piping (Including

all the Ckts. Length) with tabular insulation between each set of

indoor & outdoor units complete as per our standard specifications.

4.0 Control Cabling

Providing and Fixing of Interconnecting cabling between each set

of indoor & outdoor units complete as per our standard

specifications.

4.1 NS For Cassette AC RM 65 230.00 14950 14950

5.0 Drain Piping

Providing and Fixing of Insulated PVC drain piping for indoor units

complete with necessary elbow, tees, reducers etc.

Digitally signed by AMIT

6.0 Air Distribution Work

6.1 Factory Fabricated GI Duct

Supply, installation, balancing and commissioning of factory

fabricated GSS sheet metal rectangular / round ducting complete

with neoprene rubber gaskets, elbows, splitter, vanes, Hangers &

Supports etc. as per approved drawings and specifications of

following sheet thickness complete as required.

6.2 Site Fabricated GI Duct

Supply, installation, balancing and commissioning of fabricated at

site GSS sheet metal rectangular / round ducting complete with

neoprene rubber gaskets, elbows, splitter, vanes, Hangers & Supports

etc. as per approved drawings and specifications of following sheet

thickness complete as required.

Supply, installation, testing and commissioning of GI volume 42276

control duct damper complete with neoprene rubber gaskets,

nuts, bolts, screws linkages, flanges etc, as per specifications.

6.4 NS Flexible Canvass Connection

Providing and Fixing of Fire Retardent Flexible Canvass Connection. Nos. 5 4200 21000 21000

6.5 Duct Insulation

Supplying and fixing of following thickness duly laminated aluminium

fol of mat finish closed cell nitrile rubber Class 'O' insulation on

16.23 existing duct after appying suitable adhesive for nitrile rubber. The

joimts shall be sealed with 50mm wide and 3 mm thick self adhesive

nitrile rubber tape insulation cpmplete as per specifications and as

16.23.1 required.

6.6 Duct Accoustic lining

Supply and fixing of acoustic lining of supply air duct and plenum 56640

with 25 mm thick resin bonded glass wool having density of 32

kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm

centre to centre covered with Reinforced Plastic tissue paper and

0.5 mm thick perforated aluminum sheet fixed to inside surface of

ducts with cadmium plated nuts, bolts, stick pins, CPRX compound

etc. complete as required and as per specifications.

6.7 Grills, Diffusers & Dampers

Supplying & fixing of powder coated extruded aluminium Supply Air 91050

6.7.1 16.15 Grills with aluminium volume control damper as per specifications. Sq.m 10.0 9105 91050

Digitally signed by AMIT

Supplying & fixing of powder coated extruded aluminium Return Air 88650

6.7.2 16.16 Grills with louver but without aluminium volume control damper as Sq.m 15.0 5910 88650

per specifications.

Supplying & fixing of powder coated extruded aluminium Supply Air 121840

6.7.3 16.17 Diffusers with aluminium volume control damper as per Sq.m 10.0 12184 121840

specifications.

Supplying & fixing of powder coated extruded aluminium Return Air 97452

6.7.4 16.18 Diffusers without aluminium volume control damper as per Sq.m 12.0 8121 97452

specifications.

6.7.5 Fire Dampers & Actuator

Supplying, Fixing, testing and commissioning of fire dampers in

supply air duct/main branch and return air path as and where

required of required sizes i/c control wiring, the damper shall be

motorized and spring return so as to close the damper in the event

16.20 of power failure automatically and open the same in case of

power being restored. The spring return action shall be inbuilt

mechanism and not externally mounted. The damper shall also

be closed in the event of fire signal complete as required and

as per specifications.

6.8 VAV Boxes with Controllers

Supply, installation and testing of Variable Air Volume Damper. The

NS damper shall be complete with controller and electrically operated

actuator, theromstat & sensor etc.

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

A) SANITARY INSTALLATION

1.01 17.78 Providing and fixing white vitreous china extended wall Each 2 13036.55 26073.10 0.00

mounting water closet of size 780x370x690 mm of approved

shape including providing & fixing white vitreous china cistern

with dual flush fitting, of flushing capacity 3 litre/ 6 litre

(adjustable to 4 litre/ 8 litres),including seat cover, and cistern

fittings, nuts, bolts and gasket etc complete.

1.02 8.10 Providing and fixing stone slab with table rubbed, edges

rounded and polished, of size 75x50 cm deep and 1.8 cm thick,

fixed in urinal partitions by cutting a chase of appropriate width

with chase cutter and embedding the stone in the chase with

epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 6 mm nominal size) as per

direction of Engineer-in-charge and finished smooth.

8.10.2 Granite Stone of approved shade Sqm 2 3542.85 7085.70 0.00

1.03 17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia

CP Brass single hole basin mixer of approved quality and make,

including painting of fittings and brackets, cutting and making

good the walls wherever required:-

(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm Each 2 3459.05 6918.10 0.00

CP Brass single hole basin mixer

1.04 17.31 Providing and fixing 600x450 mm beveled edge mirror of Each 2 1411.15 2822.30 0.00

superior glass (of approved quality) complete with 6 mm thick

hard board ground fixed to wooden cleats with C.P. brass

screws and washers complete.

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

1.05 17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink

as per IS: 13983 with C.I. brackets and stainless steel plug 40

mm, including painting of fittings and brackets, cutting and

making good the walls wherever required :

17.10.1 Kitchen sink with drain board

1.06 17.11 Providing and fixing white vitreous china laboratory sink with

C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P

brass waste and 40mm C.P. brass trap with necessary C.P. brass

unions complete, including painting of fittings and brackets,

cutting and making good the wall wherever required :

1.07 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

1.08 17.34 Providing and fixing toilet paper holder :

1.09 17.71 Providing and fixing PTMT liquid soap container 109 mm wide, Each 2 146.30 292.60 0.00

125 mm high and 112 mm distance from wall of standard shape

with bracket of the same materials with snap fittings of

approved quality and colour, weighing not less than 105 gms.

1.10 17.22A Providing and fixing CP Brass 32mm size bottle trap of approved Each 2 886.25 1772.50 0.00

quality & make and as per the direction of engineer in charge.

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

1.11 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm Each 2 204.70 409.40 0.00

long, 200 mm wide with minimum distances of 37 mm from wall

face with concealed fittings arrangement of approved quality

and colour, weighing not less than 88 gms.

1.12 MR Providing and fixing Coat Hook. Each 2 763.00 0.00 1526.00

1.13 MR Providing ,Fixing of straight / offset type flexible single body Each 2 700.00 0.00 1400.00

push fit type WC pan connector of with integral single mould

sealing fins made of flexible EVA body to be fixed with

manufacture supplied grease, including rubber bush / adaptor

for use with C.I pipe as supplied with the pan connector.

1.14 18.49 Providing and fixing C.P. brass bib cock of approved quality Each 2 434.20 868.40 0.00

conforming to IS:8931 :

1.15 17.16a Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube Each 2 299.35 598.70 0.00

upto 1meter long with S.S. Triangular plate to european type

W.C. Of approved quality and make as approved by engineer

1.16 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and Each 14 500.35 7004.90 0.00

geyser points of approved quality conforming to IS:8931 15mm

1.17 18.21.2.1 Providing and fixing uplasticised PVC connection pipe with Each 14 85.20 1192.80 0.00

brass unions : 45 cm length , 15 mm nominal bore

1.18 18.65 Providing and fixing PTMT soap Dish Holder having length of Each 2 96.75 193.50 0.00

138mm, breadth 102mm, height of 75mm with concealed fitting

arrangements, weighing not less than 106 gms.

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

1.19 17.73 Providing and fixing PTMT towel rail complete with brackets

fixed to wooden cleats with CP brass screws with concealed

fittings arrangement of approved quality and colour.

17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide Each 2 573.60 1147.20 0.00

and effective height of 88 mm, weighing not less than 170 gms

1.20 MR Supply,Installation, testing and commissioning of Water Heater

complete with heavy gauge hot and cold water flexible pipe

connections, Nano polymer coated tank, 8 bar pressure ,of

approved make complete with all necessary material as

directed by Engineer - in - Charge.

a) 25-Litre Storage capacity Each 3 12616.00 0.00 37848.00

1.21 MR Providing & Fixing of Grab bar 600 mm of non slipping grip as Each 5 4034.00 0.00 20170.00

per standard specification of use in disabled toilet complete

with brackets suitable for wall installation as per approved

sample complete in all respect.

1.22 MR Supply installation, testing and commissioning of water cooler Each 5 97888.00 0.00 489440.00

with Inbuilt Aquagaurd RO purification + UV(50LPH) .Cooling

capacity shall be 60 liter & 80 liter shall be storage capacity.Its

should have 7 stages purification process,fully

automatic,rectangular tank with Forced fin and tube

condenser,Non-corrosive SS-304 outer body,Food-grade SS-304

stainless steel inner tank (18/8 or 18/10),PUF

insulation,Reciprocating compressor with R22 Refrigerant.Water

outlet temp is aprrox 17 deg c ,Operating power supply 230 +

10% V AC,50 Hz,1 PH,No of Cold water Faucet-2.

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

1.23 MR Providing and fixing of Infrared sensor controlled tap Battery Each 21 19163.00 0.00 402423.00

operation with external battery compartment and 4x AA

alkaline batteries including flexible hoses G 3/8 int. thread x 450

mm with prefilter and flow regulator ; flow volume: max. 3.8

l/min independent of pressure ; can be adjusted to 1.33 lpm

(For LEED) with additional areator 28 931 00 99 ; flow pressure:

0,5 - 5 bar ,max. resting pressure 8 bar (Model no. of 02 172 06

TOTAL FOR SANITARY INSTALLATION 78721.00 952807.00

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

B) WATER SUPPLY

2.01 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing the

pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the

cost of cutting chases and making good the same including

testing of joints complete as per direction of Engineer in

Concealed work, including cutting chases and making good

a) 18.8.1 15 mm nominal dia Pipes Mtr. 5 441.15 2205.75 0.00

b) 18.8.2 20 mm nominal dia Pipes Mtr. 35 513.75 17981.25 0.00

c) 18.8.3 25 mm nominal dia Pipes Mtr. 15 626.05 9390.75 0.00

d) 18.8.4 32 mm nominal dia Pipes Mtr. 10 712.75 7127.50 0.00

e) DSR-2021 40 mm nominal dia Pipes Mtr. 0 865.00 0.00 0.00

f) 50 mm nominal dia Pipes Mtr. DRAINAGE, 1205.00 0.00 0.00

2.02 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, including

fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement

and testing of joints complete as per direction of Engineer in

Internal work - Exposed on wall

a) 18.7.1 15 mm nominal dia Pipes Mtr. 2 255.90 511.80 0.00

b) 18.7.2 20 mm nominal dia Pipes Mtr. 10 325.10 3251.00 0.00

c) 18.7.3 25 mm nominal dia Pipes Mtr. 10 408.55 4085.50 0.00

d) 18.7.4 32 mm nominal dia Pipes Mtr. 5 500.95 2504.75 0.00

e) 18.7.5 40 mm nominal dia Pipes Mtr. 0 674.35 0.00 0.00

e) 18.7.6 50 mm nominal dia Pipes Mtr. 0 927.00 0.00 0.00

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

e) DSR-2021 65 mm nominal dia Pipes Mtr. 50 1714.00 0.00 85700.00

e) BASED 80 mm nominal dia Pipes Mtr. 10 2128.00 0.00 21280.00

e) 100 mm nominal dia Pipes Mtr. 0 3268.00 0.00 0.00

2.03 MR Providing and fixing forged brass operated ball valve of full

flow of superior quality having minimum working pressure of 16

a) 15 mm nominal bore Each 2 765.00 0.00 1530.00

b) 20 mm nominal bore Each 2 985.00 0.00 1970.00

c) 25 mm nominal bore Each 2 1421.00 0.00 2842.00

d) 32 mm nominal bore Each 0 2292.00 0.00 0.00

e) 40 mm nominal bore Each 0 3250.00 0.00 0.00

2.04 DSR E&M- Supplying, fixing, testing and commissioning of butterfly valve of

2022- 18.11 PN 1.6 rating with bronze/gunmetal seat duly ISI marked

complete with nuts, bolts, washers, gaskets conforming to IS

13095 of following sizes as required :

2.05 MR Providing, fixing, testing and commissioning moterise Ball valve

of following sizes, for filling of overhead tanks complete with

high & low level switchs & pressure switch to control the valve.

The level controller shalll be installed in over head tank. The

level switch will close the valve when water level is high &

open the valve when level is low in the tank. The system should

be complete in all respect with accessories, 220V AC / 24 V DC,

IP 67 water level control unit, Control Panel, copper control

wiring in whether proof casing etc.

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

TOTAL FOR WATER SUPPLY 59446.00 113322.00

C) INTERNAL DRAINAGE SYSTEM

Providing and fixing soil, waste and vent pipes

3.01 MR Providing and fixing low noise insulated Polyproplene piping

system as per DIN EN 12056 and DIN1986-100 with 3 layer pipe

made of External layer -PP, middle layer-Mineral reinforced PP,

Internal layer-PP. push-fit type, food safe, having high impact

and stiffness, offering sound levels of not more than 10 dBA as

per DIN 4109 at a flow rate of 2 l/s and having pipe ring stiffness

as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and

DIN 19560, density of pipe = 1.9 g/cm3, elongation break 50%

and tensile strength 20 N/mm2,Coefficient of linear expansion

0.09 mm/mK with all necessary fittings fitted with factory fitted

lip ring including cutting and making good the walls, floors,

R.C.C. work etc or also incluiding painting with ordinary cement

based paint for external installation. (including MS structural

support & U clamps as required)

a) 110 OD mm dia Pipes Metre 35 1811.00 0.00 63385.00

b) 75 OD mm dia Pipes Metre 10 1166.00 0.00 11660.00

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

3.02 MR Providing and fixing low noise insulated Polyproplene piping

system as per DIN EN 12056 and DIN1986-100 with 3 layer pipe

made of External layer -PP, middle layer-Mineral reinforced PP,

Internal layer-PP. push-fit type, food safe, having high impact

and stiffness, offering sound levels of not more than 10 dBA as

per DIN 4109 at a flow rate of 2 l/s and having pipe ring stiffness

as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and

DIN 19560, density of pipe = 1.9 g/cm3, elongation break 50%

and tensile strength 20 N/mm2,Coefficient of linear expansion

0.09 mm/mK with all necessary fittings fitted with factory fitted

lip ring including cutting and making good the walls, floors,

R.C.C. work etc. (including MS structural support & U clamps as

required) - For indirect waste inside toilet/kitchen

For waste pipes

3.03 MR Providing and fixing PP white Trap with minimum 50mm water

seal with rubber seal on inlet to push fit hopper for indirect

waste connections.

a) 110 mm inlet & 110 mm outlet Long ht Each 2 1505.00 0.00 3010.00

3.04 MR Providing and fixing floor drain (FD) with 50mm outlet and 100

mm inlet having 19mm seal for indirect floor drain (FD).

3.05 MR Providing and fixing Multi Trap (MT) with 50mm outlet and 100

mm inlet having 19mm seal for indirect Multi Trap (MT).

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

3.05 MR Providing, fixing, testing and commissioning of pipe inlet fittings Each 5 827.00 0.00 4135.00

by fixing Tee 110 x50/110 x75 mm (as required) fixed on 'P' traps

for connecting fixture drains/ extension pices in PP including

fixing and sealing inlet joint with drip seal / Pipe seal joint as

required complete.

3.06 MR Providing and fixing 1 mm thick stainless steel grating with

frame for floor traps or drains of required pattern including

cutting and making good the floors complete.

3.07 MR Providing and fixing clean out pipe (door piece) for cleaning

as required complete complete with all fitting, clamps,

accessories and civil works.

3.08 17.77 Providing and fixing M.S. holder bat clamp of approved design

to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat

brackets made of 50x5 mm flat of specified shape, projecting

75 mm outside the wall surface and fixed on wall with 4nos,

6mm dia expansion hold fasteners, including drilling necessary

holes in brick wall/ CC/ RCC surface and the cost of bolts etc.

The pipes shall be fixed to the already fixed brackets with the

help of 30 mm x1.6 mm galvanised M.S. flats of specified shape

and of total length 420 mm and shall be fixed with M.S. nuts,

bolts, & washers of size 25x6 mm, one bolts on each side of the

a) 17.37.3 Total bracket length 1040 mm of approved shape and design Each 10 365.65 3656.50 0.00

(for three 100 mm dia pipes)

TOTAL FOR DRAINAGE 3657.00 98838.00

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE

SI.No. DSR-2021/ Description of Item UNIT TOTAL DSR RATE MR RATE DSR AMOUNT MR AMOUNT

D) DRAINAGE, PUMPS & EQUIPMENT

4 1 Submersible pumps for toilet & sink Sewage sumps

4.01 1.1 Supply, installation, testing and commissioning of continuous

duty submersible centrifugal non-clogging drainage cutter

pumps complete with 3 phase motor with all necessary

protection and mechanical seal etc. complete with all

ancillaries including float type level controllers, electrical

control panels fabricatd from 14 gauge CRCA sheet volt meter

ammeter with selector switch, TPMCB, 5 VA CL : CTs, phase

indicating lamps protected by 2 amp SP MCB, DOL starter,

necessary wiring, cable alleys, earthing, interlocking, starter

with Automatic float type level controller, providion of high

level alarm, sequence timer, both pumps may run

simultaneously at pre determind level. 1Set -(1Working +

1Standby) along with one panel complete. 1 Set of pumps - (1

Working + 1 Standby)

Vendor to submit proposed pump model with duty curve.

a 1.1.1 Flow rate : 2 LPS each

Head : 7.5 Mts

Solid Handling : 10-12 MM

Location : Sump of floor level

Purpose : Plant Room Drainage

MOC : SS body SS Impeller & Shaft Set 2 79,181 158362.00

Note : Shop drawing for the installation to be approved by the

Project Manager prior to execution.

DRAINAGE, PUMPS & EQUIPMENT 158,362.00

GRAND TOTAL (DSR+MR) 1,465,153.00

GRAND TOTAL (DSR+MR) 1,465,153.00

Digitally signed by AMIT

Interior fit out works for office space of ITAT at Tower B, 1st, 2nd 3rd (half) floor, World Trade Centre, Nauroji Nagar, New Delhi

DETAILED ESTIMATE FOR ELECTRIAL INSTALLATION WORK

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

S.H.-I POINT WIRING

1.0 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in

surface/ recessed steel conduit with modular switch modular plate

suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc.as required.

2.0 1.54 Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point (without independent switch etc.) with 1.5 sq. mm

FRLS PVC insulated copper conductor single core cable in surface/

recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable etc. as required.

3.0 1.4 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed steel conduit,

2 way modular switch, modular plate, suitable GI box and earthing the 20 Point 1 981 39 620

point with 1.5 sq.mm. FR PVC insulated copper conductor single core

cable etc as required.

4.0 1.5 Wiring for power plug points with 2 x 4 sq.mm. FRLS PVC insulated, Cu.

Conductor, single core cable in surface/ recessed steel conduit along

with 1 No. 4 sq.mm. FRLS PVC insulated copper conductor single core

cable for loop earthing as required.

5.0 1.6 Wiring for light plug points / power plug points with 4 x 4 sq.mm. FRLS PVC

insulated, Cu. Conductor, single core cable in surface/ recessed steel

conduit along with 2 Nos. 4 sq.mm. FRLS PVC insulated copper conductor 500 Metre 662 3 31 000

single core cable for loop earthing as required.

6.0 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FRLS PVC insulated copper conductor, single core cable in

surface/ recessed Steel conduit as required

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

7.0 1.25 Supplying and fixing two module stepped type electronic fan regulator

on the existing modular plate switch box including connections but 250 Nos. 369 92 250

excluding modular plate etc. as required.

8.0 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts,

complete as required.

9.0 1.31 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 3 pin 5/6 A

modular socket outlet and 5/6 A modular switch, connections etc. as

10.0 1.56 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6

A modular socket outlet and 2 nos. 5/6 A modular switch, connections 378 Nos. 676 2 55 528

etc. as required. (For light plugs to be used in non-residential buildings).

11.0 1.32 Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 5/6 A &

15/16 A modular socket outlet and 15/16 A modular switch, connections

etc. as required.

12.0 1.57 Supplying & fixing suitable size GI box wih modular plate and cover in

front on surface or in recess including providing and fixing 25 A modular

socket outlet (near equipment point) and 25 A modular SP MCB, “C” 40 Nos. 727 29 080

curve (at accessible point) including connections, painting etc. as

13.0 2.18 Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2

pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP,

MCB, in sheet steel enclosure, on surface or in recess, with chained metal

cover for the socket out let and complete with connections, testing and

commissioning etc. as required.

15.0 2.20 Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4

pole and earth, metal enclosed plug top alongwith 30 A, “C” curve,

TPMCB, in sheet steel enclosure, on surface or in recess, with chained 5 Nos. 4 107 20 535

metal cover for the socket out let and complete with connections,

testing and commissioning etc. as required.

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

16.0 1.34 Supplying and fixing brass batten/ angle holder including connection

etc. as required.

17.0 1.26 Supplying and fixing modular blanking plate on the existing modular

plate & switch box excluding modular plate as required.

18.0 Civil-10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for

ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5

mm thick M.S. sheet with its top surface hacked for proper bonding, top

lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 0 Each 156.00

mm dia round headed screws, one lock at the corners. Clamp shall be

made of 12 mm dia M.S. bar bent to shape as per standard drawing.

19.0 1.49 Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

20.0 Raceways and Conduits only

20.1 Supplying and fixing of following MS raceway system with neoprene

gasketted removable cover fixed to the raceway by countersunk

cadmium plated screws at 300 mm intervals recessed in floors including

the cost of chasing and making good. The MS raceway system

alongwith all fittings like bends, T-joints, couplers etc. shall be fabricated

from 1.6 mm thick and covers from 2 mm thick electro galvanised MS

sheets finished with powder coating paint finish of approved colour and

shall include the cost of providing 2 nos 25 mm x 6 mm GI strips fixed to

the metal portion in electrical contact throughout the length of the

raceway complete as per specifications as required and as below.

a) NON DSR 300 mm wide x 50 mm deep 45 Metre 2298.00 1 03 410

b) NON DSR 200 mm wide x 50 mm deep 50 Metre 1876.00 93 800

c) NON DSR 150 mm wide x 50 mm deep 70 Metre 1546.00 1 08 220

d) NON DSR 50 mm wide x 50 mm deep 80 Metre 985.00 78 800

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

20.2 Supplying and fixing of following floor recessed junction boxes for MS

raceway systems fabricated from 1.6 mm thick electro galvanized MS

sheets finished with powder coating paint finish with 2 mm thick

neoprene gasketted removable cover fixed by counter sunk cadmium

plated screws including the cost of earth links at all joints to ensure earth

continuity and including the cost of chasing and making good recess in

floor etc complete as required and as below.

a) NON DSR 350 mm x 350mm x 50 mm deep 40 Nos 2567.00 1 02 680

b) NON DSR 250 mm X 250 mm X 50 mm deep 50 Nos 1987.00 99 350

c) NON DSR 200 mm X 200 mm X 50 mm deep 100 Nos 1897.00 1 89 700

d) NON DSR 100 mm X 100 mm X 50 mm deep 150 Nos 1567.00 2 35 050

20.3 Supply and fixing IS embossed black enamelled MS recessed and/or

surface conduiting system including cost of providing saddles,GI fish

wires etc for surface conduiting and/or cost of cutting and filling chases

for recessed conduiting complete as per specification, as required and

a) NON DSR 20mm dia 100 Metre 250.00 25 000

b) NON DSR 25mm dia 400 Metre 300.00 1 20 000

c) NON DSR 32mm dia 120 Metre 450.00 54 000

S.H.-II MCCB, MCB & DISTRIBUTION BOARDS

1.0 2.2 Providing and fixing following rating and breaking capacity and pole

MCCB in existing cubicle panel board including drilling holes in the

cubical panel, making connections etc. as required. (for VTPN DB)

2.0 2.3 Supplying and fixing following way, single pole and neutral, sheet steel,

MCB distribution board, 240 V, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

3.0 2.4 Supplying and fixing following way, horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess,

complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required.

(But without MCB/RCCB/Isolator)

3.4 NON DSR 12 way (4 + 36), Double door 12 Nos. 10 785 1 29 420

4.0 2.5 Supplying and fixing of following ways surface/ recess mounting, vertical

type, 415 V, TPN MCB distribution board of sheet steel, dust protected,

duly powder painted, inclusive of 200 A tinned copper bus bar, common

neutral link, earth bar, din bar for mounting MCBs (but without MCBs and

incomer ) as required . (Note : Vertical type MCB TPDB is normally used

where 3 phase outlets are required.)

4.2 2.5.2 8 way Double door (4 + 24)-Also used for 6 way VTPN DB 3 Nos. 10 165 30 495

5.0 2.23 Supplying and fixing Cable End Box (Loose Wire Box) suitable for following

single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on

surface/ recess, complete with testing and commissioning etc. as

5.1 2.23.2 For 8 way, Double door SPN MCBDB 4 Nos. 832 3 328

6.0 2.24 Supplying and fixing Cable End Box (Loose Wire Box) suitable for following

triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on

surface / recess, complete with testing and commissioning etc.as

6.1 2.24.1 For 4 way, Double door TPN MCBDB 2 Nos. 1 080 2 160

6.2 2.24.2 For 6 way, Double door TPN MCBDB 2 Nos. 1 124 2 248

6.3 2.24.3 For 8 way, Double door TPN MCBDB 10 Nos. 1 340 13 400

8.0 2.25 Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple

pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts,

on surface/ recess, complete with testing and commissioning etc. as

9.0 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

9.2 2.10.3 Double pole (used as 25A DP MCB) 40 Nos. 656 26 240

9.3 2.10.4 Triple pole (used as 25A TP MCB) 0 Nos. 1 007

10.0 NON DSR Supplying and fixing following rating, double pole, 240 volts, MCB

complete with connections, testing and commissioning etc. as required.

10.1 NON DSR 40 Amp DP MCB 12 Nos. 994 11 928

10.2 NON DSR 63 Amp DP MCB 0 Nos. 994

11.0 NON DSR Supplying and fixing of following rating, 240/415 volts, "C" curve, four pole

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

11.1 NON DSR 25 Amp FP MCB 24 Nos. 1 217 29 208

11.2 NON DSR 32 Amp FP MCB 3 Nos. 1 217 3 651

11.3 NON DSR 40 Amp FP MCB 40 Nos. 1 890 75 600

11.4 NON DSR 63 Amp FP MCB 40 Nos. 1 890 75 600

12.0 NON DSR Supplying and fixing of following rating double pole (Single phase and

neutral) 240 volts, residual current circuit breaker (RCCB), having a

current sensivity current 100 miliampere in the existing MCB DB complete

with connections, testing & commissioning etc. as required.

13.0 NON DSR Supplying and fixing of following rating, 240/415 volts, "C" curve, three

pole miniature circuit breaker suitable for inductive load of following

poles in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

13.1 NON DSR 40 Amp TP MCB 2 Nos. 1 422 2 844

13.2 NON DSR 63 Amp TP MCB 3 Nos. 1 422 4 266

14.0 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

S.H.-III. LIGHT FITTING & FANS

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

1.0 NON DSR Supply, installation, testing & commissioning of Surface mounted LED

downlighter fitting, fixture should have minimum efficacy at System level

(Not Chip Level) ≥ 110lumens/watt, with Minimum system Lumens 1100,

Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50 Lumen

maintenance, CCT should be 5700K-6500K, CRI ≥ 80, PF ≥ 0.95, THD ≤ 5%, 150 Nos. 1 595 2 39 250

IP-20 rated, Die Cast Al heat sink with PMMA Diffuser. Luminaries

manufacture shall provide LM79 report from NABL accredited lab & LM80

report issued by LED manufacturer.

2.0 NON DSR Supply, installation, testing & commissioning of Surface mounted LED

downlighter fitting, fixture should have minimum efficacy at System level

(Not Chip Level) ≥ 110lumens/watt, with Minimum system Lumens 1600,

Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50 Lumen

maintenance, CCT should be 5700K-6500K, CRI ≥ 80, PF ≥ 0.95, THD ≤ 5%, 40 Nos. 1 897 75 880

IP-20 rated, Die Cast Al heat sink with PMMA Diffuser. Luminaries

manufacture shall provide LM79 report from NABL accredited lab & LM80

report issued by LED manufacturer.

3.0 NON DSR Supply, installation, testing & commissioning of Surface mounted LED

downlighter fitting, fixture should have minimum efficacy at System level

(Not Chip Level) ≥ 110lumens/watt, with Minimum system Lumens 2000,

Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50 Lumen

maintenance, CCT should be 5700K-6500K, CRI ≥ 80, PF ≥ 0.95, THD ≤ 5%, 20 Nos. 2 309 46 180

IP-20 rated, Die Cast Al heat sink with PMMA Diffuser. Luminaries

manufacture shall provide LM79 report from NABL accredited lab & LM80

report issued by LED manufacturer.

4.0 NON DSR Supply, installation, testing & commissioning of Recess mounted LED

downlighter fitting, fixture should have minimum efficacy at System level

(Not Chip Level) >=110lumens/watt, with Minimum system Lumens 1200,

Life of fixture (Including Driver) : 40000 burning Hrs. @ L70B50 Lumen

maintenance, CCT should be 5700K-6500K, CRI ≥80, PF ≥0.95, THD≤5%, IP- 10 Nos. 2 009 20 090

20 rated, Aluminium Extruded/Die Cast Housing with PMMA Diffuser.

Luminaries manufacture shall provide LM79 report from NABL accredited

lab & LM80 report issued by LED manufacturer.

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

5.0 NON DSR Supply, installation, testing & commissioning of Recess mounted LED

downlighter fitting, fixture should have minimum efficacy at System level

(Not Chip Level) >=110lumens/watt, with Minimum system Lumens 1500,

Life of fixture (Including Driver) : 40000 burning Hrs. @ L70B50 Lumen

maintenance, CCT should be 5700K-6500K, CRI ≥80, PF ≥0.95, THD≤5%, IP- 150 Nos. 2 198 3 29 700

20 rated, Aluminium Extruded/Die Cast Housing with PMMA Diffuser.

Luminaries manufacture shall provide LM79 report from NABL accredited

lab & LM80 report issued by LED manufacturer.

6.0 NON DSR Supply, installation, testing & commissioning of Recess mounted LED

downlighter fitting, fixture should have minimum efficacy at System level

(Not Chip Level) >=110lumens/watt, with Minimum system Lumens 2000,

Life of fixture (Including Driver) : 40000 burning Hrs. @ L70B50 Lumen

maintenance, CCT should be 5700K-6500K, CRI ≥80, PF ≥0.95, THD≤5%, IP- 4 Nos. 2 700 10 800

20 rated, Aluminium Extruded/Die Cast Housing with PMMA Diffuser.

Luminaries manufacture shall provide LM79 report from NABL accredited

lab & LM80 report issued by LED manufacturer.

7.0 NON DSR Supply, installation, testing & commissioning of Surface LED batten made

of aluminium extruded / PVC housing with high efficiency

polycarbonate/Acrylic diffuser, LED Used shall be SMD type and fixture

should have minimum efficacy at System level >=110lumens/watt with

Minimum system Lumens 2200, Life of fixture: 25000 burning Hrs. @ L70B50

Lumen maintenance, CCT of 5700K-6500K, CRI ≥80, PF ≥ 0.95 & THD≤10%,

Minimum Internal Surge Protection 2.5KV. Luminaire manufacture shall

provide LM 79 report from NABL accredited lab & LM80 report issued by

LED manufacturer.

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

8.0 NON DSR Supply, installation, testing & commissioning of Surface mounted IP 66 &

IK 08 LED luminaire made of scratch resistant unbreakable

polycarbonate in grey finish. PG 16 x 1.5 cable gland is used for

maintaining ingress protection with High quality polycarbonate diffuser in

opal finish for glare free uniform light distribution, snap fitted to the

housing , Surface & suspended through 2 nos. SS clamps & screws

provided with fixture LED Used shall be SMD type and fixture should have

minimum efficacy at System level (Not Chip Level) ≥120 lumens / watt

with Minimum system Lumens 2000, Life of fixture (Including Driver) : 50000 10 Nos. 3 500 35 000

burning Hrs. @ L70 B50 Lumen maintenance, CCT of 5700K-6500K, CRI ≥80,

THD≤10% & PF ≥0.95, fixture Min working temp range - 0°C < Ta < 45°C,

integral electronic driver (SMPS based constant current supply) with low

THD, Output Short-circuit / Open Circuit protection, Surge protection &

Safety test as per IS:15885 Part 2/Sec 13, luminaries manufacture shall

provide LM79 report from NABL accredited lab & LM80 report to be issued

by LED manufacturer.

9.0 NON DSR Supply, installation, testing & commissioning of Surface LED batten made

of aluminium extruded / PVC housing with high efficiency

polycarbonate/Acrylic diffuser, LED Used shall be SMD type and fixture

should have minimum efficacy at System level >=110lumens/watt with

Minimum system Lumens 1000, Life of fixture: 25000 burning Hrs. @ L70B50

Lumen maintenance, CCT of 5700K-6500K, CRI ≥80, PF ≥ 0.95 & THD≤10%,

Minimum Internal Surge Protection 2.5KV. Luminaire manufacture shall

provide LM 79 report from NABL accredited lab & LM80 report issued by

LED manufacturer.

10.0 NON DSR Supply, installation, testing & commissioning of Recess mounted LED

panel (2‘ X 2‘) made of CRCA housing with high efficiency PMMA Diffuser

, LED Used shall be SMD type and fixture should have minimum efficacy

at System level (Not Chip Level) ≥120 lumens / watt with Minimum system

Lumens 3600, Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50

Lumen maintenance, CCT of 5700K-6500K, CRI ≥80, THD ≤ 5% & PF ≥ 0.95,

fixture Min working temp range - 0°C < Ta < 45°C, Driver casing should be

of metal & not plastic for better thermal cooling & having Minimum

Internal Surge Protection 2.5KV , luminaries manufacture shall provide

LM79report from NABL accredited lab & LM80 report to be issued by LED

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

11.0 NON DSR Supply, installation, testing & commissioning of Recess mounted LED

panel (4‘ X 1‘) made of CRCA housing with high efficiency PMMA Diffuser

, LED Used shall be SMD type and fixture should have minimum efficacy

at System level (Not Chip Level) ≥120 lumens / watt with Minimum system

Lumens 3600, Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50

Lumen maintenance, CCT of 5700K-6500K, CRI ≥80, THD≤10% & PF ≥0.95,

fixture Min working temp range - 0°C < Ta < 45°C, Driver casing should be

of metal & not plastic for better thermal cooling & having Minimum

Internal Surge Protection 2.5KV , luminaries manufacture shall provide

LM79report from NABL accredited lab & LM80 report to be issued by LED

12.0 NON DSR Supply, installastion, testing & commissioning of Linear LED High Bay

luminaire, surface/suspended mounted, made of Extruded aluminium /

Standard alloy housing. The luminaire should have Highly advanced LEDs

mounted on metal-clad PCB’s. The luminaire shall have system efficacy ≥

130lm/w & shall deliver minimum system lumen output of 16000 lumens.

The LED CCT shall be 4000K. The LED shall be compliant with LM80

standard with Useful life of not less than 50000 burning Hrs (Complete LM

80 test report for LED should be submitted). The LEDs used in luminaire

should comply with CCT of 4000 K and CRI of Minimum 80. LEDs used

must be tested as per EN62471 for Photo biological Safety of humans and

Report of the same from LED Manufacturer shall be submitted. The

luminaire shall be with electronic driver suitable to operate on input

voltage range of 150V to 270V ( nominal rated voltage – 240V) with

minimum 4KV surge protection, PF ≥ 0.95 and THD < 10% . The luminaire 10 Nos. 13 190 1 31 900

shall have following certifications: LM79 Test Report from NABL

accredited Lab , LM 80 report issued by LED manufacturer. The luminaire

shall comply with IS10322. The luminaire & driver shall be BIS registered.

The luminaire shall be IP 20 or higher rated. The areas where the luminaire

is to be installed in false ceiling the successful bidder/contractor shall

ensure to install the luminaire by making correct sized cut-out in the false

ceiling & install the luminaire with a properly fabricated to-the size frame

of same colour as of ceiling. The frame shall be wither made of extruded

aluminium or sheet steel & shall be powder coated with colour matching

the false ceiling.

13.0 NON DSR Supply, installastion, testing & commissioning of 30W LED Bed Head Light.

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

14.0 NON DSR Supply, installastion, testing & commissioning of LED Bulkhead with a

nominal system lumen output of 600 lumens and a minimum system

efficacy of 100 lm/W. The luminaire shall have a rated system lifetime of

50,000 burning hours at L70. The luminaire should have a color

temperature of 6500K and CRI > 70. The luminaire shall meet IP66 rating

and IK 09 rating with THD < 20% and PF > 0.9. The luminaire housing should

made of High pressure die cast Aluminium with polycarbonate front

diffuser. The total power consumption should not exceed 10W (including

driver). Including 3 core 1.5 sq.mm FRLS PVC insulated and PVC sheathed

copper conductor cable and earthing etc. Up to suitable point

complete as required.

15.0 NON DSR Black painted Extruded aluminium housing. Green / Red LED’s mounted

inside the housing. Laser engraved Signage matter on Single / Double

Acrylic sheet fixed on one side. In double sided version black paper is

inserted. Ni-Cd Battery back up to 2 hrs. (Charged up to 8 - 10

Hrs).Mounting strings provided for pendent mounting Operating Voltage

150-280V AC Ambient operating temperature. – 0 to 450C Ingress 25 Nos. 9 913 2 47 825

protection – IP42.

220208 BESL 03 LED SSD WBB GREEN 240 3 8W OR

220209 BESL 03 LED SSD WBB RED 240 3 8W OR

220210 BESL 03 LED DSD WBB GREEN 240 3 8W OR

220211 BESL 03 LED DSD WBB RED 240 3 8W

16.0 19.1 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5

star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of

insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies,

shackle kit, safety rope, copper winding, Power Factor not less than 0.9,

Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210

Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%,

remote or electronic regulator unit for speed control and all remaining

accessories including safety pin, nut bolts, washers, temperature rise=75

degree C (max.), insulation resistance more than 2 mega ohm, suitable

for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

17.0 NON DSR Supplying and fixing of 250 mm sweep Exhaust fan with all accessories

suitable for operation single phase 230 volt 50 cycle per second per sec.

AC supply etc. as required. in the existing opening, including making the

hole to suit the size of the above fan, making good the damage,

connection, testing, commissioning earthing etc. as required.

17.0 NON DSR Natural white (3000/4000K/6500K Luminaire) Hard LED Strip having light

output min 1000 Lumens per mtr and system efficiancy better than 100

LPW, Low Voltage 12VDC system, with Thermo-conductive adhesive 3M

base for safe installation on almost any flat surface for IP-20 protection, 100 Mtr 680 68 000

CE & ROHS complaince with indoor/ Outdoor driver fixed on Surface of

wall complete etc. as required.

1.4 NON DSR Floor Distribution Board

1 No.-100A, Four Pole MCCB, 35KA with standard Thermal Magnetic

releases for over current and short circuit release , Auto Manual Selector

Switch, ON, OFF Indication, 100A Auto Change Over switch (ATS) for Auto

Change over of supply with following accessories:-

a) Multi Function Meter and one set of 3 Nos. Metering tape wound CT’s

of ratio 100/5A, Class-1 accuracy and 15VA Burden -1 Set.

160A TPN Aluminium Bus Bar with heat Shrinkable Coloured PVC Sleaves

and DMC/SMC Bus Bar Supports at required intervals complete for cross

section, size supports & their spacing for with standing fault level of 35 KA

3Nos. 63A 4P MCB of 25 KA.

2Nos. 40A TP MCB of 25 KA.

1Nos. 20A DP MCB of 25 KA.

Item as stated above 3.00 No. 147,166.00 4 41 498

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

1.5 NON DSR UPS DB

1 No.-200A, Four Pole MCCB, 35KA with standard Thermal Magnetic

releases for over current and short circuit release , Auto Manual Selector

Switch, ON, OFF Indication, with following accessories:-

a) Multi Function Meter and one set of 3 Nos. Metering tape wound CT’s

of ratio 200/5A, Class-1 accuracy and 15VA Burden -1 Set.

250A TPN Aluminium Bus Bar with heat Shrinkable Coloured PVC Sleaves

and DMC/SMC Bus Bar Supports at required intervals complete for cross

section, size supports & their spacing for with standing fault level of 35 KA

10 Nos. 63A 4P MCB of 25 KA.

2 Nos. 40A 4P MCB of 25 KA.

Item as stated above 3.00 No. 221,657.00 6 64 971

1.6 NON DSR USP DB - STAIRCASE

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

1 No.-63A, Four Pole MCCB, 25KA with standard Thermal Magnetic

releases for over current and short circuit release , Auto Manual Selector

Switch, ON, OFF Indication, with following accessories:-

a) Multi Function Meter and one set of 3 Nos. Metering tape wound CT’s

of ratio 63/5A, Class-1 accuracy and 15VA Burden -1 Set.

100A TPN Aluminium Bus Bar with heat Shrinkable Coloured PVC Sleaves

and DMC/SMC Bus Bar Supports at required intervals complete for cross

section, size supports & their spacing for with standing fault level of 25 KA

8 Nos. 25A DP MCB of 25 KA.

Item as stated above 2.00 No. 106,047.00 2 12 094

1.7 NON DSR VENTILATION PANEL

1 No. 250 Amp FP Moulded Case Circuit Breaker

1 Set of phase indicating lamps with MCB.

1 Set of ON/OFF indicating lamps with MCB.

1 No.Digital Voltmeter with Voltmeter selector switch.

1 No.Digital Ammeter with Ammeter selector switch.

1 No. Digital MFM with CT's.

300 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

5 Nos. 63 Amp TP Moulded Case Circuit Breaker.

5 Nos. 40 Amp TP Moulded Case Circuit Breaker.

5 Nos. 32 Amp TP Moulded Case Circuit Breaker.

Panel described as above 1 Nos. 5 15 989 5 15 989

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

1.8 NON DSR SUB DISTRIBUTION PANEL (FOR VRV OUTDOOR TYPICAL FLOOR)

1 No. 250 Amp FP Moulded Case Circuit Breaker

1 Set of phase indicating lamps with MCB.

1 Set of ON/OFF indicating lamps with MCB.

1 No.Digital Voltmeter with Voltmeter selector switch.

1 No.Digital Ammeter with Ammeter selector switch.

1 No. Digital MFM with CT's.

300 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

5 Nos. 63 Amp TP Moulded Case Circuit Breaker.

5 Nos. 40 Amp TP Moulded Case Circuit Breaker.

5 Nos. 32 Amp TP Moulded Case Circuit Breaker.

Panel described as above 3 Nos.

1.8 MCCB BOXES

NON DSR Supply, installation, testing & commissioning of MCCB in Sheet Steel

enclosure made out of 2 mm thick CRCA sheet suitable for 3 phase 4 wire

50Hz AC system complete with four pole Moulded Case Circuit Breaker

(ICS = 35KA) suitabel for incoming & outgoing termination including

power coating etc. complete as per specification & as required.

NON DSR 250 Amp FP MCCB 2 Nos.

NON DSR 63 Amp FP MCCB 2 Nos. 12 718 25 436

4 Supplying, installation, testing & commisioning of following capacity Plug

In/ tap off box on the existing Air Insulated CompType bus trunking/ rising

mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply made with 1.6mm

thick sheet steel enclosure (IP54) duly powder coated with provision of

MCCB (but without MCCB) complete etc. as required.

4.1 NON DSR 125 A, Isc = 15 kA for 1 second (For 100A Tap off) 3 Nos. 8 671 26 013

4.2 NON DSR 200 A, Isc = 15 kA for 1 second (For 160A Tap off) 2 Nos. 8 671 17 342

4.3 NON DSR 200 A, Isc = 15 kA for 1 second 1 Nos. 8 671 8 671

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

S.H.-V. EARTHING SYSTEM

1.0 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe of 2.7 metre long etc. with

charcoal/ coke and salt as required.

2.0 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick

including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe of 2.7 metre long etc.

with charcoal/ coke and salt as required.

3.0 5.7 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level

for conductor earth electrode, including connection/ termination with GI 100 Meter 51 5 100

thimble etc. as required.

4.0 5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess

for connections etc. as required.

5.0 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required.

6.0 5.2 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface

for connections etc. as required.

7.0 CHEMICAL GEL EATHING

5.7 Providing and fixing of Gel-Chemical Earthing Electrode of G.I.

made as pipe in pipe technology (IS:3043 1987)duly CPRI Approved

as per following specification: Length - (3000 mm) DIA (outer) - (80 mm)

DIA (Inner) - (40 mm) DIA-Terminal Strip Hole - (25 mm) Space Inside

Electrodes - (Filled with Conductive Mixture) Hot Dip Galvanizing - (70 -

100 Microns) And earth enhancing compound should be used to 4 nos. 45 687 1 82 748

treat the soil for lowering the effective ground impedance 48Kg

for each earth pit to make it maintenance free and to minimize the

ground voltage potential rise and pit covered with MS / CI Cover

with locking arrangements etc. complete as reqd.

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

S.H.-VI. CABLES, CABLE TRAYS, RACE WAYS

(LT Cables and Terminations)

7.0 NON DSR Supplying following 1.1kV grade, heavy duty XLPE insulated PVC

Sheathed Aluminum Conductor FRLS type armoured cables suitable for

415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath

provided with FRLS insulation, galvanised steel armouring (round or flat as

mentioned) and with all components as mentioned in BOQ,

specifications and schedule, complete etc. as required.

7.4 NON DSR 3.5 core, 185 sq.mm. 20 Meter 1 460 29 200

7.5 NON DSR 3.5 core, 150 sq.mm. 80 Meter 1 216 97 280

7.6 NON DSR 3.5 core, 120 sq.mm. 30 Meter 1 087 32 610

7.7 NON DSR 3.5 core, 95 sq.mm. 100 Meter 933 93 300

7.8 NON DSR 3.5 core, 70 sq.mm. 40 Meter 807 32 280

7.9 NON DSR 3.5 core, 50 sq.mm. 30 Meter 677 20 310

7.10 NON DSR 3.5 core, 35 sq.mm. 150 Meter 585 87 750

7.11 NON DSR 4 core, 25 sq.mm. 60 Meter 546 32 760

8.0 NON DSR Supplying following 1.1kV grade, heavy duty XLPE insulated PVC

Sheathed Copper Conductor FRLS type armoured cables suitable for

415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath

provided with FRLS insulation, galvanised steel armouring (round or flat as

mentioned) and with all components as mentioned in BOQ,

specifications and schedule, complete etc. as required.

8.1 NON DSR 4 core, 16 sq.mm. 40 Meter 1 434 57 360

8.2 NON DSR 4 core, 10 sq.mm. 60 Meter 1 170 70 200

8.3 NON DSR 4 core, 6 sq.mm. 80 Meter 978 78 240

8.4 NON DSR 4 core, 4 sq.mm. 150 Meter 860 1 29 000

8.5 NON DSR 2 core, 10 sq.mm. 100 Meter 789 78 900

8.6 NON DSR 2 core, 6 sq.mm. 100 Meter 721 72 100

13.0 7.8 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE

power cable of 1.1 KV grade of following size on cable tray as required.

13.1 7.8.1 Upto 35 sq. mm (clamped with cable tie) 2000 Meter 45 90 000

13.2 7.8.2 Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie) 250 Meter 92 23 000

13.3 7.8.3 Above 95 sq. mm and upto 185 sq. mm (clamped with cable tie) 300 Meter 115 34 500

13.4 7.8.4 Above 185 sq. mm and upto 400 sq. mm (clamped with cable tie) 60 Meter 185 11 100

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

14.0 9.1 Supplying and making end termination with brass compression gland

and aluminium lugs for following size of PVC insulated and PVC sheathed

/ XLPE aluminium conductor cable of 1.1 kV grade as required.

16.13 9.1.32 4 X 10 sq. mm (25mm) (used for 4 x 6 sq. mm & 4 x 4 sq. mm cable)

19.0 4.6 Supplying and installing following size of perforated Hot Dipped

Galvanised Iron cable tray (galvanisation thickness not less than 50

microns) with perforation not more than 17.5%, in convenient sections,

joined with connectors, suspended from the ceiling with G.I. suspenders

including G.I. bolts & nuts, etc. as required.

19.1 4.6.1 100 mm width x 50 mm depth x 1.6 mm thickness 50 Meter 669 33 450

19.2 4.6.2 150 mm width x 50 mm depth x 1.6 mm thickness 25 Meter 716 17 900

19.3 4.6.4 300 mm width x 50 mm depth x 1.6 mm thickness 50 Meter 963 48 150

19.4 4.6.6 450 mm wide x 50 mm depth x 2.0 mm thickness. 20 Meter 1 325 26 500

20.0 4.7 Supplying and installing following size of perforated Hot Dipped

Galvanised Iron cable tray “bends” (galvanisation not less than 50

microns) with perforation not more than 17.5%, in convenient sections,

joined with connectors, suspended from the ceiling with G.I. suspenders

including G.I. bolts & nuts, etc. as required.

20.1 4.7.1 100 mm width x 50 mm depth x 1.6 mm thickness 4 Nos. 1 159 4 636

20.2 4.7.2 150 mm width x 50 mm depth x 1.6 mm thickness 2 Nos. 1 270 2 540

20.3 4.7.4 300 mm width x 50 mm depth x 1.6 mm thickness 4 Nos. 1 852 7 408

20.4 4.7.6 450 mm wide x 50 mm depth x 2.0 mm thickness. 1 Nos. 2 683 2 683

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

21.0 4.8 Supplying and installing following size of perforated Hot Dipped

Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns)

with perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with G.I. suspenders including

G.I. bolts & nuts, etc. as required.

21.1 4.8.1 100 mm width x 50 mm depth x 1.6 mm thickness 4 Nos. 1 327 5 308

21.2 4.8.2 150 mm width x 50 mm depth x 1.6 mm thickness 2 Nos. 1 383 2 766

21.3 4.8.4 300 mm width x 50 mm depth x 1.6 mm thickness 4 Nos. 2 156 8 624

21.4 4.8.6 450 mm wide x 50 mm depth x 2.0 mm thickness. 1 Nos. 3 141 3 141

22.0 4.9 Supplying and installing following size of perforated Hot Dipped

Galvanised Iron cable tray “Cross member” (galvanisation not less than

50 microns) with perforation not more than 17.5%, in convenient sections,

joined with connectors, suspended from the ceiling with G.I. suspenders

including G.I. bolts & nuts, etc. as required.

22.1 4.9.1 100 mm width x 50 mm depth x 1.6 mm thickness 2 Nos. 1 327 2 654

22.2 4.9.2 150 mm width x 50 mm depth x 1.6 mm thickness 1 Nos. 1 383 1 383

22.3 4.9.4 300 mm width x 50 mm depth x 1.6 mm thickness 1 Nos. 2 366 2 366

22.4 4.9.6 450 mm wide x 50 mm depth x 2.0 mm thickness. 1 Nos. 3 569 3 569

23.0 4.10 Supplying and installing following size of perforated Hot Dipped

Galvanised Iron cable tray “Reducer” (galvanisation not less than 50

microns) with perforation not more than 17.5%, in convenient sections,

joined with connectors, suspended from the ceiling with G.I. suspenders

including G.I. bolts & nuts, etc. as required.

23.1 4.10.1 100 mm width x 50 mm depth x 1.6 mm thickness 1 Nos. 1 655 1 655

23.2 4.10.2 150 mm width x 50 mm depth x 1.6 mm thickness 1 Nos. 1 921 1 921

23.3 4.10.4 300 mm width x 50 mm depth x 1.6 mm thickness 1 Nos. 2 823 2 823

23.4 4.10.6 450 mm wide x 50 mm depth x 2.0 mm thickness. 1 Nos. 3 721 3 721

24.0 NON DSR Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet

1.6MM) race ways for electrical & LV wiring including neoprene gasket in

joints, cutting the floor & jaming the race way / hanging in ceiling,

supporting arrangement as approved by consultant / architect with all

necssary hard ware (including civil work) as per site requirement. The

thickness of raceway & cover shall be as per technical specification.

24.1 NON DSR 100 mm wide x 40 mm deep. 200 Meter 1 570 3 14 000

24.2 NON DSR 150 mm wide x 40 mm deep 150 Meter 1 962 2 94 300

24.3 NON DSR 200 mm wide x 40 mm deep. 200 Meter 2 682 5 36 400

24.5 NON DSR 300 mm wide x 40 mm deep. 200 Meter 3 532 7 06 400

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

25.0 NON DSR Supply & fixing of following size of Raceway Junction Box made out of GP

Sheet for electrical & LV wiring including, cutting the floor & jaming the

junction box / hanging in ceiling, supporting arrangement as approved

by consultant / architect with all necssary hard ware (including civil

work).(Junction box to be provided as per drawing/ as per site

requirement & as per specification). The thickness of junction box shall be

a as per thechnical specification.

25.1 NON DSR 150 mm wide x 50 mm deep. 100 Nos. 1 590 1 59 000

25.2 NON DSR 200mm wide x 50 mm deep 50 Nos. 1 998 99 900

25.3 NON DSR 250mm wide x 50 mm deep 40 Nos. 2 699 1 07 960

25.4 NON DSR 350mm wide x 50 mm deep 30 Nos. 3 595 1 07 850

26 NON DSR MS Channel 100x50x6mm 100 Kg 255 25 500

27 NON DSR MS angle 50x50x6 -4kg per meter 50 Kg 205 10 250

S.H.-VII. UPS SYSTEM

Supply, Installation, Testing and Commissioning of

160KVA True Online double conversion VFI

technology, High Frequency PWM using IGBT

technology, Parallel redundant, 3 phase AC Input &

1.1 NON DSR 3 phase 4 wire AC Output UPS. Input range should 2 Nos. 38 48 818 76 97 636

be 360 VAC-450 VAC, Frequency Range: 46~60 Hz,

Current Distortion: Less than < 5% at full rated UPS

output load , Dual input (separate input for rectifier

and separate input for bypass).

Output- Voltage

Stability: ± 1%, Distortion:(100% rated load with

crest factor 2.7:1), Less than 2% total harmonic

distortion(THD) for linear loads, <5%THDfor100%

balanced non-linear loads as specified by

Provisions for maintenance by pass

switch module. Microprocessor based LCD display &

indication for various electrical parameters. LED

indication with alarm for major fault. Provisions for

remote monitring indication with potential free contact etc. complete as

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

Supply, Installation, Testing and Commissioning of

12V Monoblock suitable size and nos of sealed

maintenance free batteries supporting for 160KVA

UPS System ) for providing 15 minutes

back up time with each UPS at full load with

interconnecting leads, mounting racks/stands for

stacking the batteries, along with Battery Circuit

Breaker, Connection, Interconnections, and

standard accessories etc. Complete as reqd.

1 Set = One Complet UPS + One Battery Bank of 30

minutes backup.

1.2 NON DSR Supply, Installation, Testing and Commissioning of

Parallel Redundant Kit to control the two separate

160KVA UPS work together as a unified system. The

modules synchronies the output of each UPS so it

can flow into a shared output by balancing the load 2 sets 2 47 122 4 94 244

equally amongst both the UPS. The kit allows the

total load to be taken by Single UPS if the other UPS

is out od order/taken out for service for

maintenance etc. complete as reqd.

Supply, Installation, Testing and Commissioning of

K-13 Isolation Transformer – Cubicle IP-20 With

Copper Winding with H Class Insulation including

specification Input - 415V 3ph, 3W, Delta, Output

– 415, 3Ph, 4W, ZIG ZAG, Digital Meter to Monitor

with RS485 Port Including Manual Soft Start,

Natural Cooling, LED Indicating Light for R, Y, B

Phase etc. complete as reqd. Capacity - 160KVA

Supply, Installation, Testing and Commissioning of

Microprocessor Based Transient Voltage Surge

Suppression (TVSS) System with reset facility

High/Low voltage protection with following

specifications :-

All Modes Protection : L-L, L-N, L-G, N-G

Connection Type : Parallel

Protection Level : < 0.8 kV

MCOV : Min. 320 Volts

Response Time : < 0.5 nanoseconds

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

Status Indication : LED, Dry contacts

EMI/RFI Attenuation : 40 dB typical

Fusing : Individual Fusing of MOV’s

Monitoring : Monitoring Status

Enclosure : IP-20

Mounting : Wall Mounting

1.4 NON DSR TVSS Capacity : 50KA 4 Nos. 2 65 780 10 63 120

1.5 NON DSR TVSS Capacity : 160KA 4 Nos. 4 32 960 17 31 840

Supply Installation Testing and Commissioning of 50 KVA (CVCF)

Constant Voltage Constant Frequency. CVCF is designed to

operate on different level of constant voltages & constant

frequencies as required by connected equipment’s. Constant

Voltage Constant Frequency works on standard available voltage

1.6 NON DSR & frequency & gives regulated voltage & frequency output as per 2 No. 13 41 290 26 82 580

as requirement / application.Constant Voltage Constant frequency

is suitable for unbalance supply and unbalance load. CVCF is fully

controlled by microprocessor and digital sensing circuit with built in

power filters to improve the output wave form to the pure sinusoidal

and controlled each phase individually with following specification.

Input Voltage – 415 Vac, 3 phase, 4 wire Input Voltage range - 360-460

Vac, 3 phase, 4 wire Input Frequency -50 Hz

Input Frequency range - 47-53 Hz

Output Voltage – 415 Vac +/- 0.5%

Output Frequency – 50 Hz +/-0.5%

Rate of Correction of Voltage - More than 150V/sec.

Output Voltage Adjustment:CVCF shall have provision for setting

of out put voltage within +/-5%

Voltage tolerance: static (steady state) ±1%

Frequency distortion: 1%

Total harmonic distortion: <3%

Individual harmonic distortion: 1%

Transient response: 5ms

Over load protection: 110% overload for 10 min

125% overload for 1 min

150% overload for 10 sec

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

Efficiency: More than 92%

Operational temp. 0 – 40 deg c

Storage temp. -20 deg c – 65 deg c

Relative humidity: 0-95% Rh Non-condensing

Input Over / Under Voltage

Output Over / Under Voltage

Output Overload

Output Short-circuit

Output Over / Under Frequency / Over Temperature

Forced Air Cooled

Automatic bypass along with Manual bypass

Supply, Installation, Testing and Commissioning of (AHF/APPF) Active

Harmonic Filter with CT Kit for controlling harmonic distortion at less than

4% and improving power factor from 0.7 to upto unity complete with

monitoring of phase current, phase voltage, frequency, active power, reactive

power, apparent power, power factor, total harmonic distorion of current and

1.7 NON DSR total harmonic disortion of voltage of each phase. Self diagnosis with current 3 Nos. 9 41 277 28 23 831

and voltage wave form. Suitable safeties like current limiting, under / over

voltage protection overloading and over temperature etc. Suitable RS232 port

for remote monitoring. Minor civil work should be done as per site requirement

following details & specification as are as below :-

Capacity :30Amp

Input Voltage Range : 400Volts, 3ph + N, (+10% - 15%)

Input Frequency Range : 50Hz (+ 10%)

Enclosure Protection : IP-40

Acoustics Noise Level : <65 dB @1, 0 mtr distance

Operating Temerature : 0-40 degree Celsius

Relative Humidity : Upto 95% (Non condensing)

Interface : Remote monitoring through

iii. Web Browser

Potential Free Contact : i. Filter `Trip'

ii. Filter `On'

Standards/Approval : i. IEEE 519 for Compensated Harmonics

ii. IEC / EN - 62040 - 2 Category C3

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

iii. EN - 50178

CT : 3000 A : 5A, 15VA, Class 1 with short link

Harmonis Filtering :None zero sequence 3rd to 31st Harmonic

compensation, Attenuation ratio up to 96%

Cable Entry : Bottom Cable Entry

SITC of 63A static switch module with microprocessor based control and

suitable for liner and non linear load at particulars distribution board of critical

load in event of short circuit overload or any other fatal condition with built-in

Technical Protections like short circuit, Overload, High/Low Voltage cutoff

protection of load from source inclusive of Bypass facility Static Bypass Module

is activated during malfunctioning conditions of load like :-

• Short Circuit

• Bypassing of particular load if required

• Resulting in non tripping of main UPS unit

• Input Voltage (320-460VAC) 3 phase

• Input frequency 50Hz

Indication & Monitoring

• UPS Supply on/source I

• Load on UPS supply/source I

• Main supply on/source II

• Load on mains supply/Bypass

• Bypass Switch on

• Bypass Switch off

TOTAL ELECTRICAL CARRIED OVER TO SUMMARY 49 40 484 291 71 529

S.H.-VIII. FIRE ALARM SYSTEM

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

1 NON DSR SITC of Microprocessor based 4 loop control Panel , Networkable

analogue addressable type fire alarm control panel with 640 character

LCD display, The panel should be equipped with sufficient numbers of

loop with 20% spare capacity with each loop shall have a capacity of

318 analog addressable devices in one loop. Four access levels,

capable of taking Flash Scan devices, flash EPROM sufficient numbers of

programmable relay controls for controlling AHUs, pressurization fans,

ventilation fans at fire pump room, monitoring of fire sprinkler and fire

hydrant pump, 240 volts AC power supply, automatic battery charger, 24

volts sealed lead acid batteries sufficient for 24 hours normal working and

then be capable of operating the system for 2 hours during an

emergency conditions as required. The Panel shall have BACKNET CARD

for integration.

2 NON DSR SITC of the GUI based main network software must be capable of

graphically representing each facility being monitored with floor plans

and icons depicting the actual locations of the various systems; and / or

sensors’ locations. The GUI software shall be located in control room in

one of the blocks and shall monitor all the blocks panel connected with

each other. The software shall be capable of monitoring 40 Nodes with

100 MB baud Transmission rate on Fibre Optics Network and 12 MB baud

Transmission on cable or more. The software shall provide the facility to

Monitor, Control all the Digital PAVA as well as 2 way communication

from main control room using voice signals over Fire Network along with

the Fire detection signal.

3 NON DSR SITC of Networked Fire Fighters 19 inch Touch screen Graphical Display

Mimimc Panel (Incident Commander) at main entry to inform & guide Fire

Fighters for carrying out Fire fighting operations. a. The software

shall display “YOU ARE HERE” along with icons representing standard building

objects (stairs, elevators, etc) to be shown on the floor plan b. The

software shall allow icons that represent hazardous materials stored in a

facility. screen that displays preprogrammed building contact information,

building occupancy and other general building information, display all active 1 Nos. 2 98 766 2 98 766

fire, supervisory, and security events within an event list. The screen shall

also provide the arial view of entire building via touch screen navigation.

c. The equipment shall allow the importation of externally developed floor

plans in Windows Metafile (WMF), JPEG (JPG), Graphics Interchange Format

(GIF) and Bitmap (BMP) format.

Digitally signed by AMIT

S.NO. ITEM DESCRIPTION QUANTITY UNIT RATE (IN RS.) AMOUNT (IN RS.)

DSR-2022 MR DSR-2022 MR

4 NON DSR SITC of Network Repeater Panel with 6 inch or 640-characters; The LCD

shall Display all events / detectors, devices status of complete systems in

the networked, The NRP shall be equipped with QWERTY Keypad. 2 Nos 2 34 569 4 69 138

Mounting options include an annunciator box, and blank modules are