Loading
Loading…
Loading…
Tender Value
₹1.3 Cr
EMD Value
₹2.5 L
Closing Date
4 May 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
ELECT BAHL
15 conditions · 4 needing a document upload
In terms of clause 1.1.12.2 (ii) of the the tender document, the tenderer must, the tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where: V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared / audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-15 (Annexure-VIB), along with copies of Audited Balance Sheets duly certified by the Chartered Accountant / Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
In terms of clause 1.1.12.2 (i) of the the tender document, the tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
SIMILAR NATURE OF WORK: The similar work is defined as under: "Design, supply, erection testing & commissioning of 50 Hz, single phase 25 kV AC OHE". (Ref: OHE Works S.No.1.1 of Pr. CEE/NR's Letter No. 181- Elect/TRD/189/Pt.II, dated 29.07.2021)
ELECTRICAL CONTRACTOR'S LICENSE: In terms of clause 1.1.12.2 (iii) of the tender document, the tenderers must submit attested copy of valid 1.1.1 Class-A Electrical contractor license along with his offer. Offer shall be summarily rejected if tenderer does not have Electrical contractor license issued by State / Central government.
27 conditions · 12 needing a document upload
Requisite earnest money, (ON ONLINE mode (No Documentary Proof required))
Cost of tender document
Requisite earnest money ,(ONLINE mode )
(ii) In case tenderer is other than sole proprietorship firm, following documents shall be submitted by the tenderer:
(a) Partnership Firm: The tenderer shall submit (i) a copy of Partnership Deed and (ii) a copy of Power of Attorney (duly registered as per prevailing law) in favour of an individual to sign the tender documents and create liability against the Firm.
(b) Joint Venture (JV): The tenderer shall submit documents as mentioned in Clause 17 of the Tender Form (Second Sheet).
(c) Company registered under Companies Act-2013: The tenderer shall submit (i) the copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company; and (ii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.
(d) LLP (Limited Liability Partnership) Firm: If the tender is submitted on behalf of a LLP Firm registered under LLP Act-2008, the tenderer shall submit alongwith the tender- (i) a copy of LLP Agreement, (ii) a copy of Certificate of Incorporation; and (iii)a copy of Power of Attorney/Authorisation issued by the LLP Firm in favour of the individual to sign the tender on behalf of the LLP Firm and create liability against the Firm.
(e) Registered Society & Registered Trust: The tenderer shall submit (i) a copy of the Certificate of Registration, (ii) Deed of Formation; and (iii) a copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust.
(iii) If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm / Partnership firm / Joint Venture / Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender.
(iv) After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society etc. shall be neither asked nor considered, if submitted.
(v) A tender from JV / Partnership firm etc. shall be considered only where permissible as per the tender conditions.
(vi) The Railway will not be bound by any change in the composition of the firm made subsequent to the submission of tender. Railway may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.
15. The tenderer whether sole proprietor, a company or a partnership firm / joint venture (JV) / registered society / registered trust etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person specifically authorizing him/them to submit the tender, sign the agreement, receive money, co-ordinate measurements through contractor's authorized engineer, witness measurements, sign measurement books, compromise, settle, relinquish any claim(s) preferred by the firm and sign "No Claim Certificate" and refer all or any disputes to arbitration.
16. Employment/Partnership etc. of Retired Railway Employees: (a) Should a tenderer be a retired Engineer of the gazetted rank or any other gazetted officer working before his retirement, whether in the executive or administrative capacity or whether holding a pensionable post or not, in the Engineering or any other department of any of the railways owned and administered by the President of India for the time being, or should a tenderer being partnership firm / company / joint venture (JV) / registered society / registered trust etc have as one of its partners a retired Engineer or retired gazetted officer as aforesaid, or should a tenderer being an incorporated company have any such retired Engineer or retired officer as one of its directors or should a tenderer have in his employment any retired Engineer or retired gazetted officer as aforesaid, the full information as to the date of retirement of such Engineer or gazetted officer from the said service and in case where such Engineer or officer had not retired from government service at least 1 year prior to the date of submission of the tender as to whether permission for taking such contract, or if the Contractor be a partnership firm or an incorporated company, to become a partner or director as the case may be, or to take the employment under the Contractor, has been obtained by the tenderer or the Engineer or officer, as the case may be from the President of India or any officer, duly authorized by him in this behalf, shall be clearly stated in writing at the time of submitting the tender. Tenders without the information above referred to or a statement to the effect that no such retired Engineer or retired gazetted officer is so associated with the tenderer, as the case may be, shall be rejected.
(b) Should a tenderer or Contractor being an individual on the list of approved Contractors, have a relative(s) or in the case of partnership firm/ company / joint venture (jv) / registered society / registered trust etc. one or more of his shareholder(s) or a relative(s) of the shareholder(s) employed in gazetted capacity in the Engineering or any other department of the _____________ railway, the authority inviting tenders shall be informed of the fact at the time of submission of tender, failing which the tender may be disqualified/rejected or if such fact subsequently comes to light, the contract may be rescinded in accordance with provision in clause 62 of standard general conditions of contract.
PAN CERTIFICATE : PAN The tenderer shall submit the photocopy of Permanent Account Number (PAN) issued by Income Tax authority attested by Gazetted officer / self attested.
GSTIN number: Bidder shall submit the photocopy of GSTIN number
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions. Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Payment of Earnest money Deposit (EMD) and Tender Document Cost (TDC) in respect of E- tendering will only be accepted through Net-Banking and payment Gateway only. No other mode of payment except this will be accepted and any offer without the same will be treated as invalid. Details of bank account no. and technical details have been provided for in the software (IREPS) to which prospective registered tenderers will have access at the time of tendering.
However, For service contracts, MSMEs registered with District Industries Centres, Khadi and Village Industries Commission, Khadi and Village Industries Board, Coir Board, National Small Industries Corporation, Directorate of Handicraft and Handloom, Any other body specified by Ministry of MSME, shall be supplied such tender document free of cost on confirmation (Xerox Copy) of their evidence to this effect
Tenderers are required to upload PAN Certificate, GSTIN Certificate as well as Certificates as per Annexure-9, Annexure- 10, Annexure-11, Annexure-12, Annexure-13, Annexure-14, Annexure-15, Annexure-16, Annexure-18, Annexure-19, Annexure-19A, Annexure-20 & Annexure-21.
(iii) If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm / Partnership firm / Joint Venture / Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender.
(iv) After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society etc. shall be neither asked nor considered, if submitted.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Design, supply, erection, testing & commissioning of 25 KV OHE work in connection with setting up of additional Trip shed at Shri Mata Vaishno Devi Katra (SVDK) station".
17-E-C-TRD-TS-SVDK-25
17-E-C-TRD-TS-SVDK-25
Open
Works - General
12 Months
Ramban, Jammu And Kashmir
₹0
₹2.5 L
4 May 2026
7 Apr 2026
20 Apr 2026
187 items across 6 schedules · ₹1,26,75,276.04 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Preparation of drawing as per RDSO design for Over Head Equipment | Per Track KM | 3.00 | 11,347.3 | 34,041.9 |
| 2 | Supply of Concrete for foundation and plinth in other than hard & rocky soil | cum | 25.00 | 6,739.54 | 1,68,488.5 |
| 3 | Erection of Concrete for foundation and plinth in hard & rocky soil | cum | 25.00 | 6,468.2 | 1,61,705 |
| 4 | Supply of galvanized steel fabricated masts / other supporting structure | MT | 8.00 | 1,33,140.05 | 10,65,120.4 |
| 5 | Erection of galvanized steel fabricated masts / other supporting structure | MT | 8.00 | 9,841.96 | 78,735.68 |
| 6 | Supply of fabricated and galvanized steel work (SPS) other than mast with necessary components | MT | 1.00 | 1,36,183.45 | 1,36,183.45 |
| 7 | Erection of fabricated and galvanized steel work (SPS) other than mast with necessary components | MT | 1.00 | 9,062.7 | 9,062.7 |
| 8 | Supply of Single bracket assembly (without insulator) | Numbers | 20.00 | 21,636.61 | 4,32,732.2 |
| 9 | Erection of Single bracket assembly | Numbers | 20.00 | 2,111.39 | 42,227.8 |
| 10 | Supply of composite type Stay and bracket tube insulators (CD 1050mm) for single bracket assembly | Set | 20.00 | 10,966.29 | 2,19,325.8 |
| 11 | Erection of insulators for single bracket assembly | Set | 20.00 | 1,390.8 | 27,816 |
| 12 | Supply of OHE with complete fitting (For Conventional type) without Contact & Catenary Wires as per explanatory Notes | Per Track KM | 0.60 | 28,419.37 | 17,051.62 |
| 13 | Erection of OHE with complete fitting (For Conventional type) without Contact & Catenary Wires as per explanatory Notes | Per Track KM | 0.60 | 28,404.66 | 17,042.8 |
| 14 | Supply of copper jumper wire | Numbers | 5.00 | 7,457.92 | 37,289.6 |
| 15 | Erection of copper jumper wire | Numbers | 5.00 | 731.88 | 3,659.4 |
| 16 | Supply of Guy Rod Assembly | Numbers | 4.00 | 10,432.99 | 41,731.96 |
| 17 | Erection of Guy Rod Assembly | Numbers | 4.00 | 1,226.2 | 4,904.8 |
| 18 | Supply of Composite 9T Insulators (CD 1050mm) as per latest RDSO Specifications | Kg | 6.00 | 7,402.27 | 44,413.62 |
| 19 | Erection of 9-Tonne insulator | Numbers | 6.00 | 1,406.26 | 8,437.56 |
| 20 | Supply of regulating equipment 3 pulley type ATD with counter weight | Numbers | 2.00 | 72,740.08 | 1,45,480.16 |
| 21 | Erection of regulating equipment 3 pulley type ATD with counter weight | Numbers | 2.00 | 4,222.79 | 8,445.58 |
| 22 | Supply of Section Insulator assembly including bar insulator assembly for conventional OHE | Numbers | 2.00 | 54,983.62 | 1,09,967.24 |
| 23 | Erection of Section Insulator assembly including bar insulator for conventional OHE | Numbers | 2.00 | 3,366.41 | 6,732.82 |
| 24 | Supply (without insulator) of 25KV Single Pole(SP) Isolator without earth contact assembly | Numbers | 2.00 | 51,738.44 | 1,03,476.88 |
| 25 | Erection of 25KV Single Pole(SP) Isolator without earth contact assembly | Numbers | 2.00 | 4,510.18 | 9,020.36 |
| 26 | Supply of 25KV post / pedestal insulators for isolators | Numbers | 12.00 | 8,953.89 | 1,07,446.68 |
| 27 | Erection of 25KV post / pedestal insulators for isolators | Numbers | 12.00 | 383.1 | 4,597.2 |
| 28 | Supply of an Earth contact assembly in an isolator | Numbers | 2.00 | 7,985.94 | 15,971.88 |
| 29 | Erection of an Earth contact assembly in an isolator | Numbers | 2.00 | 1,117.49 | 2,234.98 |
| 30 | 1042Supply, Erection, Testing and Commissioning of High Voltage Presence/Absence detection and indication system.Sensing voltage Range: 230V-33KV ,Operating Voltage: 18KV- 27KV, Contactless Sensing: 1.5 meter to 2 meter LED Indicator: Dual Side IndicationmSize of the Indicator: 12" x 6". | Numbers | 8.00 | 1,10,000 | 8,80,000 |
| 31 | Supply of single earth electrode with earth pit complete as per RDSO Drg No. ETI / OHE / P / 7020 or latest | Numbers | 5.00 | 4,137.27 | 20,686.35 |
| 32 | Erection of single earth electrode with earth pit complete as per RDSO Drg No. ETI / OHE / P / 7020 or latest | Numbers | 5.00 | 1,343.47 | 6,717.35 |
| 33 | Manufacturing supply of Retro Reflective type structure Number plate as per RDSO drg. No.ETI / OHE / P / 7503 or latest along with all fixing arrangement. | Numbers | 6.00 | 676.28 | 4,057.68 |
| 34 | Erection / Fixing of Retro Reflective type structure Number plate as per RDSO drg. No.ETI / OHE / P / 7503 or latest along with all fixing arrangement. | Numbers | 6.00 | 85.13 | 510.78 |
| 35 | Supply of material without insulators for termination of OHE conductor | Numbers | 4.00 | 7,226.18 | 28,904.72 |
| 36 | Erection of material for termination of OHE conductor | Numbers | 4.00 | 1,018.06 | 4,072.24 |
| 37 | Supply of splicing and extension of anchored over head equipment with components | Numbers | 2.00 | 6,310.36 | 12,620.72 |
| 38 | Erection of splicing and extension of anchored over head equipment with components | Numbers | 2.00 | 5,676.3 | 11,352.6 |
| 39 | Supply of Structure Bonds | Numbers | 10.00 | 896.08 | 8,960.8 |
| 40 | Erection of Structure Bonds | Numbers | 10.00 | 221.8 | 2,218 |
| 41 | Supply of Transverse (cross rail, inter-track, Z & special type) bonds | Numbers | 10.00 | 1,050.94 | 10,509.4 |
| 42 | Erection of Transverse (cross rail, inter-track, Z & special type) bonds | Numbers | 10.00 | 151.73 | 1,517.3 |
| 43 | Supply of Longitudinal bonds | Numbers | 30.00 | 667.99 | 20,039.7 |
| 44 | Erection of Longitudinal bonds | Numbers | 30.00 | 141.79 | 4,253.7 |
| 45 | Dismantling of OHE termination assembly | Numbers | 2.00 | 1,492.22 | 2,984.44 |
| 46 | Dismantling & removal of Anchor assembly | Numbers | 2.00 | 1,161.49 | 2,322.98 |
| 47 | Dismantling of Bracket Assembly | Numbers | 4.00 | 1,625.79 | 6,503.16 |
| 48 | Reclamation of OHE mast | Numbers | 4.00 | 4,455.12 | 17,820.48 |
| 49 | Cutting and removal of existing structure | Numbers | 2.00 | 1,123.3 | 2,246.6 |
| 50 | Dismantling of Guy Rod Assembly | Numbers | 769.19 | 2 | 1,538.38 |
| 51 | Dismantling of fabricated steel other than mast | MT | 0.50 | 15,795.77 | 7,897.89 |
| 52 | Dismantling of OHE / Alluminium Feeder Wire | Per Track KM | 1.00 | 18,279.04 | 18,279.04 |
| 53 | Dismantling of copper jumper | Numbers | 5.00 | 682.82 | 3,414.1 |
| 54 | Raising / Restoration of OHE height as per OHE profile by Change of incumbrance / Re- droppering of span | Each Span | 30.00 | 1,909.29 | 57,278.7 |
| 55 | Adjustment of Turnout or insulated / un- insulated overlap | Numbers | 2.00 | 1,873.45 | 3,746.9 |
| 56 | Dismantling of Three Puley type ATD & termination | Numbers | 2.00 | 4,217.54 | 8,435.08 |
| 57 | Dismantling of section insulator assembly | Numbers | 2.00 | 3,510.91 | 7,021.82 |
| 58 | Dismantling of 9-Tonne insulator | Numbers | 4.00 | 748.88 | 2,995.52 |
| 59 | Dismantling of Pedestal insulator | Numbers | 4.00 | 667.97 | 2,671.88 |
| 60 | Dismantling of an Isolator | Numbers | 2.00 | 2,386.01 | 4,772.02 |
| 61 | Dismantling of Anticreep | Numbers | 2.00 | 2,242 | 4,484 |
| 62 | Supply of Large Span Wire (130 Sq mm) | Metre | 100.00 | 982.78 | 98,278 |
| 63 | Erection of Large Span Wire (130 Sq mm) | Metre | 100.00 | 158.36 | 15,836 |
| 64 | Supply of Large Span Ending (130 Sq mm) | Numbers | 4.00 | 833.51 | 3,334.04 |
| 65 | Erection of Large Span Ending (130 Sq mm) | Numbers | 20.00 | 79.95 | 1,599 |
| 66 | Fabrication, developing and supply of fabricated Sectioning Diagram, Schematic and TSWR diagram Boards with computerized digital printing on adhesive Venyle of adequate size as per requirement | Square Foot | 40.00 | 1,955.08 | 78,203.2 |
| 67 | Supply and erection of "Electric Engine Stop" Board size 900x600x 2mm with supply of fixing material (Clamp, back flat strip & fasteners) | Numbers | 5.00 | 4,141.35 | 20,706.75 |
| 68 | Supply and erection of "Caution unwire turnout" Board size 900x600x 2mm with supply of fixing material (Clamp, back flat strip & fasteners) | Numbers | 5.00 | 2,802.13 | 14,010.65 |
| 69 | Supply and erection of "Caution live wire" Board size 400x270x 2mm with supply of fixing material (Clamp, back flat strip & fasteners) | Numbers | 20.00 | 2,442.52 | 48,850.4 |
| 70 | Supply and erection of "Caution clearance to OHE nearby restricted" Board size 450x270x 2mm with supply of fixing material (Clamp, back flat strip & fasteners) | Numbers | 20.00 | 1,353.31 | 27,066.2 |
| 71 | Supply and erection of "Power Block Working Limit" Board size 450x450x2mm with supply of fixing material (Clamp, back flat strip & fasteners) | Numbers | 5.00 | 1,526.74 | 7,633.7 |
| 72 | Supply and erection of "Protective Area" Board size 12"x18" with supply of fixing material (Clamp, back flat strip & fasteners) | Numbers | 20.00 | 2,787.28 | 55,745.6 |
| 73 | Supply of various types 25KV caution Board / Plates as per explanatory Notes | Numbers | 10.00 | 374.27 | 3,742.7 |
| 74 | Erection of various types 25KV caution Boards / plates as per explanatory Notes | Numbers | 10.00 | 89.02 | 890.2 |
| 75 | Supply of various types of 25KV Danger Boards / plates as per explanatory notes | Numbers | 5.00 | 504.69 | 2,523.45 |
| 76 | Erection of various types of 25KV Danger Boards / plates as per explanatory notes | Numbers | 5.00 | 64.13 | 320.65 |
| 77 | Design, manufacturing, supply of Retro Reflective type Sigma Board with non- reflective black ground as per RDSO drg. No. TI/Drg/OHE/PLTBRD/RDSO/ 00036/12/0 (Size 450 mm x 600 mm) and RDSO specification No. ETI/OHE/33A (12/97) Rev. 8 or latest including transportation and all taxes etc. | Numbers | 5.00 | 1,809.36 | 9,046.8 |
| 78 | Cost of 4 Nos. 12mm dia GI nuts & bolts 300 mm long (fully threaded) with necessary washer, spring washer for different OHE Mast / Portals etc including transportation and all taxes | Set | 8.00 | 248.61 | 1,988.88 |
| 79 | Cost of GI backing angle for mounting arrangement size 40x40x5x450mm (4 Nos.) including transportation and all taxes | Set | 8.00 | 425.37 | 3,402.96 |
| 80 | Erection of clamps-GI backing angle for arrangement size 40x40x5x450mm (4 Nos.) 12mm dia GI nuts & bolts 300 mm long (fully threaded) with necessary washer, spring washer including Retro Reflective type sigma board with non reflective back ground at different OHE Mast / Portals etc including transportation and all taxes | Set | 8.00 | 315.12 | 2,520.96 |
| 81 | Handling, Leading, loading and Transportation charges for Railway supply material from different Railway sites and released material from different Railway sites, if any to concerned TRD Depot | MT | 6.00 | 2,780.61 | 16,683.66 |
| 82 | Supply of Stranded Annelaled Copper Jumper wire Large 105 Sq. mm 19/7/1.016 mm Conforming to RDSO Spec. No. ETI/OHE/3 (2/94) with A&C Slip No.1 or latest | Kg | 5.00 | 915 | 4,575 |
| 83 | "Supply of Contact Wire Parallel clamp (LARGE) RI No. 1031-2 with RDSO Drg .No. ETI/OHE/P/1030-2 REV-D or latest " | Numbers | 5.00 | 219.33 | 1,096.65 |
| 84 | Supply of Contact Wire Parallel Groove Clamp RI No. 1031-3 Complete with fasteners as per RDSO Drg. No. ETI/OHE/P/1030-3, Rev-A. RDSO Spec. No. TI/SPC/OHE/Fittings/0130 with A&C slip No. 1 or latest | Numbers | 50.00 | 217.78 | 10,889 |
| 85 | Supply of Contact Wire Parallel Clamp (Small) RI No.-1041-2, RDSO Spec: TI/SPC/OHE/Fittings/0130 with A&C Slip No.1, Drg. No.: ETI/OHE/P/1040-2 Rev.E or latest | Numbers | 200.00 | 194.67 | 38,934 |
| 86 | Supply of Parallel clamp (150/160) RI.No.1051-3 and as per RDSO Drg. No. ETI/OHE/P/1050-3 Rev-A or Latest RDSO Spec No. TI_SPC_OHE_Fittings _0130_with A&C Slip No.1 or latest | Numbers | 25.00 | 325.67 | 8,141.75 |
| 87 | Supply of 160 Sq. mm Stranded Annelaled Copper Jumper wire Conforming to RDSO Spec. No. ETI/OHE/3 (2/94) with A&C Slip No.1 or latest | Numbers | 5.00 | 944.6 | 4,723 |
| Schedule total | ₹47,14,922.1 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderDocumentTSSVDK.pdf
ATTACHMENT
SimilarnatureofworkI.pdf
ATTACHMENT
Letterregfardingpartnershipfirm.pdf
ATTACHMENT
clarification FormV
ATTACHMENT
ClarificationregardingsubmissionofAnnexure-VofGCC.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .