PROVN OF SPECIAL REPAIR TO BLDG NO NP-11,NP-20,P-03,T-55,CERTAIN MINOR AND REVENUE WORK UNDER GE SATWARI

Amount

Dismantling of ceiling board(Fibre,pulp,,any type of insulation etc) or insulation board / slabs/any thickness including cover fillets

Dismantling timber scantlings 40 sq. cm and over in section, in any position ( framed work) complete all as specified.

All as per srl item No 02 but in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section framed Work) all as specified.

Demolition of brick/stone/boulder masonary work built in cement mortar or cement lime mortar complete including all quoins, arches, pillar etc complete.

Dismantling wall and ceilling board (fibre, pulp, insulation, etc) or insulation boards/slab/blankets any thickness including cover fillets complete all as specified.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, complete all as specified.

Demolition of cement concrete (unreinforced) of any description and in any position.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, or bedded & pointed in any mortar

Dismantling floor,hearth or wall tilling,cement mortar bedding(but not backing) , terrazzo toping all as spd and directed by Engr-in Charge.

Demolition of brick work masonry built in cement mortar including all quoins, pillars etc but excluding ashlars facing, dressed stone work and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Taking down chowkats or frames n. exc. 1.5 sqm each but with shutter without taking off shutters from the frame.

Taking down chowkats or frames exc. 1.5 sqm & n.exc. 4 sqm each but with shutter without taking off shutters from the frame.

Taking down shutter of any description 1 sqm and n.exc. 2 sqm each

Taking down shutter of any description exc. 1 sqm and n.exc. 2 sqm each and refixing, with resecuring or easing in same opening

Dismantling barbed wire of any description or in any positon complete and removing from site all as specified.

Excavation in trenches not exc. 1.5 m wide and n.exc. 1.5 m in depth etc, for foundation in any type of soil and getting out complete all as required.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for pipe line,underground cables or for manholes not exc 10 Sqm on plan in hard and dense soil and getting out.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil.

Returning, filling in (any type of soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil.

Removal of excavated (soil) to a distancen.exce 250m but not exc 500m and and depositing where directed a t a level not exc 1.5 mtr above the starting point.

Removal of excavated (soil) to a distancen.exce 50m and and depositing where directed a t a level not exc 1.5 mtr above the starting point.

M&L Cement concrete in foundations, Type-D2, 1:4:8 ( 40 mm thick graded aggregate) filling and mass concrete as in foundation complete all as specified.

M&L for Reinforcement concrete M-25 (20 mm graded aggregates) as in foundations, including rafts, footings, foundations beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete.

M&L for Reinforcement concrete M-25 (20 mm graded aggregates) as in beams, cantileveres, bressummers, lintels over 1.5 m span.

M&L RCC M-25 (Design mix ) as in column complete as required.

Form work to side of rough finished concrete surfaces as in foundations, footing, base of column, side of foundation and plinth beam and similar work vertical or to batter fair finished flat surfaces.

Form work to side pillars, post, strust, pier, columns and similar works square or rectangular rough finished and flat concrete surfaces.

M&L for formwork fo rough finish flat surfaces of concrete to sides & soffits of floor & roof beam , lintel, in floors or roofs, landings, balconies and shelves etc for flat surfaces.

S & F angle iron post and strusts/double swan neck horn on security wall including securing bolt, including cutting top, drilled, welding fixing as required confirming to FE-290 Gde-E-165

S&F Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing complete all as specified

S&F Concertina coil 450mm dia complete all as specified

M & L Hard core of gauge n.exc. 63 mm, deosited spread and levelled in layers n.exc. 15 cm thick using broken stone or boulders, watered and rammed to a true surfaces.

Cement concrete work as in pavement/hardstanding of thickness 100 mm thick PCC 1:2:4 type B-2 using 40mm graded stone aggregate finishing the surface concrete topping even and fair including use & waste of form work and and to divide the area in panels all as specified and directed.

Finishing Surface of concrete floor by brooming finishing the surface concrete topping in green Condition

Forming Expension joints 100mm deep x 10mm wide filled with sealing with bituminous sand filler 1:3 complete all as specified and directed.

M&L PCC 1:2:4 type B1, using 20 mm graded stone aggregate as in surface channel and drain complete all as specified.

M&L for cement concrete type B- 0 1:2:4 (12.5 mm graded aggregate) as in copings including formwork , weathering , slightly rounded or chamfered angles all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete using extra cement including forms ,moulds, mitred/stopped ends etc complete all as specified and directed.

S&F for non skid joint free ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor, set & jointed in neat cement slurry & pointed in white or coloured cement to match and incl 25mm thick PCC type B0 1:2:4 using 12.5mm grades stone aggregate & laid over and incl 15mm thick screed bed in CM (1 : 4) complete all as specified & as directed.

S&F glazed ceramic coloured tiles 300mmx200mmx6mm thick set and jointed in neat cement slurry and pointed in colour cement on vertical surfaces such as in dado / skirting etc over and including 10 mm thick rendering in cement mortar 1:4 etc complete.

M&L for Cement concrete type C - 2 (1:3:6) using 40 mm graded stone aggregate as in sub base of drains etc completeall as specified and as directed

M&L for Extra for forming fair finished drain or channel 30Cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM (1:4) finished even and smooth etc complete all as specified and as directed

Taking down cement plaster and decayed concrete of any description from roof projection, repair with 15mm thick rendering on fair face of concrete surfaces in CM 1:4 with water proofing compound ( As per manufacturer detail ) including junction portion, making proper slope towards out side, finished even and smooth with PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) and provision of two coats of cement based paint and including all necessary scaffolding / safety arrangement for carrying out work on outer side of Double Storey Building complete all as specified and directed. (Note: Water proofing admixture measured and paid separately)

M&L for brick work with sub class ‘B’ bricks old size straight or curved on plan exc 6 M radius built in cement mortar (1 : 6) etc complete all as specified and as directed.

M&L for brick work with sub class ‘B’ straight or curved on plan exc 5 M radius built in cement mortar (1 :4) etc complete all as specified and as directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete, but except brick, i.e. using serviceable bricks obtained from ' here-in-before all as specified and as directed.

Brick work in cement mortar 1: 4, using sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall all as specified and directed by Engr. In charge

Treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1: 2 ( 1 cement 2 coarse sand ) to match the existing floors .

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area all as specified and as directed.

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in cm 1:6 finished even and smooth (with out using extra cement) incl taking down cement plaster on brick wall etc. and racking out joints hacking for key complete all as specified and as directed.

M&L Rendering 15 mm thick on fair faces of brick/concrete surfaces in cement plaster 1:4, using water proofing compound mix as per manufacturer detail, finished even and smooth without using extra cement, complete incl taking down cement plaster on brick wall etc. and racking out joints hacking for key complete all as specified and as directed. (WPC measured and paid seperately)

M&L Rendering 10 mm thick on concrete surfaces in CM 1:4 finished on even and smooth without using extra cement as in ceiling, Chajja etc.incl taking down old plaster

Supply only Integral water proofing compound liquid

M&L for Reinforced cement concrete 1:2:4 (nominal mix) as in slabs supported on walls, beams and coloumns and the like slab laid in slops including all necessary form work, all as specified and directed.

S&F mild steel deformed bars 10 mm dia and over cut to length bent to shape required including cranking hooking ends & binding with and including MS wire (annealed) not ness than 0.9 mm dia etc. all as spfd.

M&L TMT steel bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders in reinforcement , cut to length, bend to as required including cranking, bending an binding with annealed wire not less than 0.9 mm dia complete all as required.

M&L Non - skid digital, anti scratch, anti fungus, Ceramic joint less colored tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over 15mm thick screed bed in C:M 1:4. Make : Somany,Kajaria,Orient (sample as approved & kept in GE's sample room)

M& L for vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

M& L vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick backing in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

M& L glazed Ceramic any shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

M& L glazed Ceramic any shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick backing in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

M&L Glazed ceramic coloured tiles 450x300mmx7mm thick for work vertical surfaces such as shirking/dado and risers to step etc set and jointed in neat slurry and pointed in white /coloured cement and pigment to match the tiles over and including 15mm thick cement plaster in CM 1:4 , all as spd and directed Make : Somany,Kajaria ( sample as approved & kept in GE's sample room).

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in flooring, finished fair and even with out using extra cement.

M&L Machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed cement screed base laidand jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for tread of staircase, landing, floor, over 15 mm thick screed bed in CM 1:4 after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc.

M&L Machine cut kota stone slab 15-18 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for risers of staircase over 10mm thick fair and even plaster in CM 1:4 after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

S & F pressed steel frames made of size 1.25mm thick MS steel for door with one or more rebates incl lugs, hold fast, lock strike plate etc complete of size 105 x 60mm including one coat of red oxide primer and PCC 1:3:6 as in back fill to chowkats all as spfd.

S & F pressed steel frames made of size 1.25mm thick MS steel for door with one or more rebates incl lugs, hold fast, lock strike plate etc complete of size 125 x 60mm including one coat of red oxide primer and PCC 1:3:6 as in back fill to chowkats all as spfd.

Solid PVC door/cup board frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening.

Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suippling and fixing in the frame at site as per specification in SSR Part-I.

S & F Box type Steel windows/ventilators comprised of tubular frame and shutters made out of 1.25mm thick MS steel tube factory made with double side shutters wire gauged shutter & glass glazed shutter ( wire and glass panes shall be measured and paid separately ) with side hung shutters with steel handle and steel peg stay dovetailed ot welded incl 2 Nos tower bolts 150mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to F I frame work , incl other fittings ,hinges ,handles tarred hold fasts PCC blocks etc. all as shown on drg No CEPZ /TD-354/09 sheet 1/3 to 3/3 complete

Aluminium anodised powder coated ventilator section of frame of size 101.60 x 44.45 size ,shutters of size 42.45 X 44.45 mm , wire gauged shutter & glass glazed shutter ( wire and glass panes shall be measured and paid separately )made out of 1.2 mm thick aluminium sheet/section including necessary jointing cleats, glazing clips, rubber packing, suitable handle 1 No's in each shutter, tower bolt, hinges 75 mm long ,anodised aluminium snap beading screws, complete all as specified. Note: Sheet glass and wire mesh to be fitted will be measured and paid separately.

M&L 35 mm 2nd class H/.W plain framed factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces .The size of rail and stile as per IS :1003(Part-I ) kiln seasoned and chemically pressure treated.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters open rebated & prepare to receive glass, gauge etc (without sash bars /edges of framing plain chamfered or rounded, fitted with cut and mitred beds for securing glass etc) size of members of shutters as spd in SSR Part-I section-8 clause 8.2 (A).

S&F 225 mm ordinary rat tail mild steel rod pattern springs incl roller and roller plate complete

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm

S & F steel locking bolts with mild steel electrogalvanised plate and bright bolt not less then 10 mm dia , 100 mm size.

Small fittings of 2nd class hard wood such as brackets of any type, hing blocks, shaped doors and window stops, including all necessary labours, article n.exc. 200 cu cm each.

Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 125 mm long complete all as specified

Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 200 mm long complete all as specified

S&F 250mm long mild steel sliding bolts plate type , stove enameled black , with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts .

S & F mild steel barrel tower bolts stove enameled black with bright bolt 150 mm

S & F Aluminium handle cast type anodized of size 150 mm complete all as specified

S & F Aluminium handle cast type anodized of size 100mm complete all as specified

S & F Aluminium handle cast type anodized of size 125mm complete all as specified

S & F Butt hinges 100mm medium weight stainless steel complete all as specified and directed by Engr in charge

S&F in repair Material & labour for 18/19 mm thick MDF board as in shutters/shelves etc exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed to frame work with leaping (15 mm thick three side and 20mm thick leaping hinge side) around the shutter and fix with screws to etc complete all as specified and directed.

S & F 40 mm wide flaps Continuous (piano) hinges , mild steel bright finish or electrogalvanised as in cup boards, kitchen cabinat , etc all as directed by Engr. In Charge.

S&F galvanized mild steel wire cloth 0.456 mm nominal dia of wire and aperture 1.801 mm and fixed with tinned tacks or galvanized wire staple.

Hacking out old broken glass, (any thickness, size, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds,glazed with putty or fixed with beads.

Sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified.

S & F 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square n.exc 0.5 sqm each.

Dismantling water tanks exceeding 250 ltr capacity but not exc 500 ltrs all as spd.

S&F in repair rotational moulded polyethylene water storage tanks with float valve, plastic lid cover, triple layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 ltr incl making connection completed all as specified.

S & F angle iron as in cooler stand , welding fixing as required upto 5 mtr height from ground level confirming to FE-290 Gde-E-165 all as specified and directed by Engr. In Charge .

Preparation of new plastered surfaces of wall and applying two coats of cement base paint all as specified and directed.

Preparation new/old plastered surfaces of wall and applying two coats of oil emulsion distemper roller finish over a coat of primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 1 to 2 mm complete all as specified and as directed.

Preparation of new plastered surface of wall and apply two coat of white wash complete all as specified and directed.

Preparation of old plastered surface of wall and apply two coat of white wash complete all as specified and directed.

Preparation of old plastered surface of ceiling and applying two coat of white wash complete all as specified and directed. .

Preparation of new plastered surface of ceiling and applying two coats of white wash complete all as specified and directed. .

M & L two coats of synthetic enamel paint on steel surfaces of any description not other wise described over 10 cm width or girth incl preparation on new or previously untreated surfaces.

Preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed..

Preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed..

M&L for preparation of old decorative plastered/concreat surface of wall, chajja, facia, face of columns, beam ect by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of weather proof exterior emulsion with necessary scaffoding up to 2nd storey of building,including necessary filling of wall care putty on uneven surface as and where required all as specified.

M&L 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 20 mm thick CM 1:4 as directed by Engr-in-charge.

M&L 75mm cement concrete type C-1 (1:3:6) using 20mm graded stone aggregate as in plinth protection.

Taking down cement plaster and decayed concrete of any description from sunken portion , repair with 15mm thick rendering on fair face of concrete surfaces in CM 1:3 and neru finish , with water proofing compound ( As per manufacturer detail ) including junction portion, making proper slope towards out side, finished even and smooth with PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate). (Note: Water proofing admixture measured and paid seprately)

(a) Applying 1st course of bitumenous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the plastered surface as in WC Sunken portion . (b) Applying 2nd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 2 mm thick weight not less than 3.0 Kilogram/Square Metre with 160 Grams/Square Metre non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat. (d) Applying 4th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm.

M & L 50 mm tube medium grade cut to shape required and fixed in wall as in spout pipe complete all as specified.

Providing cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate ) in roof padding, tank stagging ,roof kerbs or mud stops, rounded or chamfered on edges finished even and smooth without using extra cement .

M&L complete removal of the existing roof treatment;taken out membrane etc, including grabbing up of tree roots , roughing and prepration surfaces of old concrete floor by picking , scurubbing down with steel brushes ,sweeping clean and washing down with water to remove dust etc.and applying the following Roof treatment complete all as specified (i) Applying a coat of bitumen primer membrane 0.4ltr/sqm by the same membrane manufacturer of density at 25 degree C’ 0.87-0.89Kg/Litre and viscosity 70-160 CPS till the surface properly impregnates and insolvent oil primer evaporates completely and applying a coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.20 kg /sqm (iii) Applying Polymeric Polypropylene polymer membrane “APP” (Atactic poly propylene polymer ) modified prefabricated five layer 3mm thick not less than 3.6 Kg/Sqm with 160 grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 overlap in length using butane torch with 10cm over laps which shall be thermo fused by flame (iv) Applying course of two coats of aluminium paint over the APP membrane all as specified. All joints and change in direction shall be covered with cement mortar 1:3 mixed with SBR latex @ 200 ml/bag of cement and curved before laying membrane

M&L non skid joint free ceramic coloured tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. Including 15 mm thick screed bed in CM 1 :4 etc complete.

M & L Glazed digital ceramic tiles in vertical surface 450x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick CM 1:4 all as specified. Make : Somany,Kajaria, ( sample as approved & kept in GE's sample room)

M & L Machine cut kota stone slab flooring 20 -25 mm thick over cement screed based laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polish complete including 20 mm screed bed layed with CM 1 :4 etc complete.

M & L Machine cut kota stone slab in skirting 20 -25 mm thick over cement screed based laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polish complete including 10 mm thick rough plastering with CM 1 :6 etc complete.

Material and labour for grinding,rubbing and polishing with machine on existing kota stone/moisac flooring/skirting laid in position including all necessoy repair work and filling of joints with grey cement mixed with pigment to match the shad complete all as directed by the Engineer-in-Charge.

S&F 6mm thick asbestos cement corrugated sheets in roofs,walls etc fixed with L type hook or cranked bolts. complete all as specified and directed by Engr-in-Charge.Make-Chaminar, Ramco, Everest

M&L for fixed in repair 6mm thick Non asbestos fibre cement building board fixed or laid on GI framework in ceiling etc complete all as specified and directed by Engr-in-Charge.

Fixing only 6mm thick Non asbestos fibre cement building board fixed or laid on GI framework in ceiling etc complete all as specified and directed by Engr-in-Charge.

S & F anodised aluminium snap grid (size of grid 605X605mm) frame work for false ceiling and hangers 6mm dia GI (upto 1200mm length) adjustting level fixed to roof slabs by means of celling cleats made out of GI flat 40X 3mm size 60mm long and expansion hold fastners 12.5 mm dia 40mm long complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

S&F wind ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; and similar small articles conforming to Fe410-0 or Fe 310-0 etc complete and all as specified and as directed

S&F prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F prepainted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified.

Taking down cement plaster on brick or stone walls etc incl racking out joints hacking for key and scrabbing down with water etc.

Material and labour for rendering 15mm thick in CM (1:4) on brick surfaces or concrete surfaces finished even and smooth w/o using extra cement etc complete

All as per srl item No 131 but in CM (1:6) finished even and smooth w/o using extra cement.

Material and labour for rendering 15mm thick in CM (1:4) on brick surfaces or concrete surfaces finished even and smooth w/o using extra cement with WPC etccomplete

All as per srl item No 133 but in CM (1:6) finished even and smooth w/o using extra cement.

Material and labour for rendering 15mm thick in CM (1:4) on other than fair faces brick surfaces or concrete surfaces finished even and smooth w/o using extra cement with WPC etc complete all as specified.

S&F in repair vitreous china squatting pan “ORISSA” pattern size 580mm X 440mm, white with PVC (SWR) P or S trap front or back inlet with integral foot rest (excl flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed. Cat Part No Make:- Cera Clovin S3010106 or equivalent in essco, jaquar, kohlar

S&F 15mm bore cast copper alloy chromium plated angle cock & cup concealed type complete all as specified and as directed Make:- ESSCO Cat part No SQT-526KN or equivalent in cera, jaquar, kohlar

S&F 15mm bore cast copper alloy chromium plated bib cock two way with wall flange complete all as specified and as directed Make:- ESSCO Cat part No SQT-512ANKN or equivalent in cera, jaquar, kohlar

S&F in repair fancy type health foucet (ABS Body) with 1 mtr long easy flex tube in chrome finish & wall hook Cat Part No :- ALD579 Make :- ESSCO Cat Part No ALE-ESS-585 or equivalent in cera, jaquar, kohlar

S&F in repairs PVC connection 15mm dia of length not less than 450mm with both ends, brass fly nut complete all as specified & as directed.

Disconnecting existing tank of capacity exceeding 250 and not exceeding 500 ltrs, setting aside (or lowering if required) for repair including cleaning & removing all scales/dirt etc from tanks & from mouths of circulating pipes and hoisting if required, reconnecting and refixing position etc, complete all as specified and directed

Disconnecting existing tank of capacity exceeding 500 and not exceeding 1000 ltrs, setting aside (or lowering if required) for repair including cleaning & removing all scales/dirt etc from tanks & from mouths of circulating pipes and hoisting if required, reconnecting and refixing position etc, complete all as specified and directed

Material & labour 35mm thick 2nd class HW factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply. The size of rail and stile as per IS:1003 (Part-I), all as directed by Engr-in-Charge. Make : as sample approved by GE

Material & labour 35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebeated and prepare to recive glass but dived into square with plain chamfered or rounded mitrd and rebeatedd sash bars stiles and rails as specifed in SSR Part-I Sec 8 clause 8.24 (a). Make : as sample approved by GE

S&F butt hinges extruded aluminium alloy with galvanised mild steel hing pin anodised and fixed type C-21, 100 mm size in toilet with PVC doors etc complete all as specified and as directed

Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified.

Supply and fixing in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.60mm complete all as specified.

M & L preparation of New steel surfaces of any description exc. 10 cm width or girth and applying two coat of synthetic enamel paint over a coat red oxide primer etc complete all as specified and as directed.

M&L two coat synthetic enamel paint over one coat of pink primer on new wooden surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed

Material and labour for three coats white wash on new surfaces of wall including preparation of surfaces etc complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint over a coat alkali resistant priming paint etc complete all as specified and as directed

M&L preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed

M&L preparation of old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed

M&L preparaing old decorated plastered or unplastered surfaces of wall, pillasters, cornices etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spot and two coats of white wash, complete all as specified and as directed

M&L preparing old decorated plastered or unplastered surfaces of wall, pilasters, cornices etc by washing rubbing down & stopping etc and applying one coat of cement base paint complete all as specified and as directed

Material and labour 75mm thick PCC 1:2:4 type C-1 using 40mm graded crushed stone aggregate as in floor/ plinth protection laid in alternate bays finished even and smooth without using extra cement including joints filling by using mastic filling comprising one part of bitumen 85/25 mixed with three parts of coarse sand by weight complete all as directed.

Pain Cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cills, lintels upto 1.5 metre clear span, steps, seismic and other similar band, plinth course,string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneels, apex stone, bed plates, kerbs etc and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form work complete, all as specified.

M&L Glazed ceramic coloured joint free tiles 300x450mmx7mm thick for work vertical surfaces such as shirking/dado and risers to step etc set and jointed in neat slurry and pointed in white /coloured cement and pigment to match the tiles over and including 15mm thick cement plaster in CM 1:4 ,including dismantling floor,hearth or wall tilling,cement mortar bedding(but not backing) , terrazzo toping all as spd and directed by Engr-in Charge.

Supply and fixing GI snap grid frame work (Grid size 605cm x 605cm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick,GI angle 24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 2 mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 7 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid complete all as specified and directed by Engr-in- Chage. Make: Gyproc,Lafarg Boral Gypsum India,India Gypsum

Taking down chowkats or frames with shutter (with out taking off shutter from the frame) n exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

Taking down chowkats or frames with shutter (with out taking off shutter from the frame) exc 1.5 sqm & n. exe 4 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

S&F 35 mm thick factory made moulded door shutter consisting of solid core single leaf flush door of 30 mm thickess, lipped with 15 mm (5x3mm) thick x 30 mm width on one stiles and top rails &10 mm (5mmx2) thick x30 mm width on the order stiles & bottom rail. The inner panel laminated with 2mm thick PVC sheet of Density 600 Kg/Cbm, Manufactured by an ISO-9001-2015 certified complany, termite proof, water proof and fire resistant moulded PVC sheet with2,4,6 raised panel design in different plain and/ or prelam colours on one side after routing the mouided design on flush door & 2mm plain and/or prelam PVC sheet on other side using rubbed based adhesive on flush door & solvent cement adhesive on the PVC liping etc, complete as per direction of Engr-in-charge.

5mm thick plaint glass as in aluminium door/windows with aluminium hollow beading/glazing clip of size 60mm x 70mm made out of 0.70mm thick aluminium section weighing not less than 0.097 Kg/RM including rubber gasket all as specified and directed at site

Aluminium anodised powder coated window/ventilator shutter, section of size 44.45 x 44.45mm made out of 1.6mm thick aluminium sheet/section including necessary jointing cleats, glazing clips, rubber packing, suitable handle 1 No's in each shutter, tower bolt, hinges 110mm long ,anodised aluminium snap beading screws, complete all as specified. Note: Sheet glass to be fitted will be measured and paid separately.

Aluminum anodized powder coated frame of size 101.60 x 44.45 made out of 1.60mm thick aluminum section fixed to floor/wall with plugs and screws complete all as specified and directed

Form work to soffit of suspended slab such as kitchen platform not exc 100 mm thick horizontal or slop in flate including fair finished to concrete surfaces.

Form work to Edges of concrete flat floor and roof n.exc 20 cm wide and similar work exc 10 cm but not exc 20 cm wide rough finished to concrete surfaces.

Form work to the side of flat wall of surface channel /drain fair finished complete all as specified and directed.

M&L 18 to 20mm thick black Granite stone (table rubbed and polished) in cooking plateform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 15mm thick screed bed in CM 1:4 after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc including cutting holes into or through reinforced cement concrete slabs for gas pipe .

M&L RCC 1:2:4 Type B-1 (using 20 mm graded aggregate) in kitchen shelves, and the like etc complete as required.

S&F Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete of 20mm bore dia all as specified and as directed.

Fixed in repairs Angle valve cast copper alloy, with chromium plated capstan head, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions and fixed complete, all as specified.

S&F Bib taps, chromium plated cast copper alloy, with capstan head, screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repairs, all as specified and as directed.

S&F in repair PVC connection insulated type suitable for hot water supply 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

S&F in repair Vitreous china wash down water closet pan (Pedestal pattern) white with plastic water closet seat cover, white closed pattern with flate bottom and cover and mild steel chromium plated or aluminised hinging device includingconnecting to drain (or out going pipe) and to flushing pipe with 'P' or 'S' trap complete e all as directed.

S&F in repair cromium plated toilet paper holder, complete all as specified.

S&F in repair cromium plated hand shower (health faucet) with 8mm dia 1.20m long flexible tube and wall hook, complete all as specified. Make :- Jaquar, Cat No- ALD-CHR-573 or equivalent in Kohler/ Artize.

S&F in repair under counter basin with fixing accessories set, size: 555 x 425 x 195mm, Oval shape, including CP cuppling and PVC waste pipe complete all as specified. Make :- Jaquar, Cat No- FLS-WHT-5701 or equivalent in Kohler/ Artize..

S&F in repair single lever basin mixer without Popup waste with 450mm Long Braided Hoses screwed down for iron pipe and fixed of 15mm dia all as per directed and specified. Make :- Jaquar, Cat no OPP- CHR-15011BPM or equivalent in Kohler/ Artize.

Vitreous china coloured half stall urinal, flat back (Large )of size 635x395x420 mm with C.P. flushing nozzle on top , grating and union for discharge pipe including PVC waste pipe , fixed in repairs, complete all as specified and directed.

S&F in repair Central Hole Basin Mixer complete all as specified.

Grating doom 100mm with or without waste hole of PTMT (Minimum weight 40 gm) all as specified and as directed.

Preparation of new/old asbestos surfaces of roof and applying two coats of weather proof paint ( any colour or tint ) all as specified and directed.

Complete removal of existing treatment from internal wall surfaces including preparation of old / new surfaces and applying two coats of oil bound distemper over 2 mm thick wall putty including preparation of old/new or previously untreated surface.

Dismantling of wroght iron or mild steel work (angle iron) of any description not other wise provided in any positon complete all as specified.

Roughning surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry @ 3kg/sqm etc complete.

Material and labour for rendering 05mm thick in CM (1:3) as in ceiling finished even and smooth w/o using extra cement.

Material & labour factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section(65x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/openning for cooler/AC where required. Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No. CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) for Provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat of coal tar on the ends of steel frame in contact with brick/concrete surface. (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames. (iii) PCC block for embedding lugs.

Description is same as above item Ser No 183 but ventilator top hunged double shutter etc complete

Description is same as above item Ser No 183 but ventilator shutter only, double shutter top hunged both gauged and glazed fixed on pressed steel frame above door with complete fitting etc complete

M&L framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165 etc complete all as specified and as directed

M&L for preparation of new plastered surfaces of walls, & applying two coats of oil bound distemper over two coat of wall care putty of 3 mm thick and one coat of primer complete all as specified.

M&L preparing old decorated plastered or unplastered surfaces of wall, pillasters, cornices etc by scraping, washing, rubbing down & stopping etc and applying two coats of oil emulsion distemper over two coat of wall putty complete all as specified and as directed

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings) as per Sample approved by Engr-in -Charge

Taking down CI/PVC pipes 100 mm dia incl all fittings like bend, branch pieces, connectors, heel rest bend etc all as specified and directed.

Taking down CI/PVC pipes 75 mm dia incl all fittings like bend, branch pieces, connectors, heel rest bend etc all as specified and directed.

S&F in repair , PVC (SWR) Type-B pipes single socketed, 110 mm dia, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. Make:- Astral, Supreme, Finolex.

S&F in repair upto 2nd storeyof building PVC (SWR) Type-B pipes single socketed, 110 mm dia, in any length with rubber ring joints, on wall complete all as specified. Make:- Astral, Supreme, Finolex.

S&F in repair PVC (SWR) Type-B pipes single socketed, 75mm dia, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.Make:- Astral, Supreme, Finolex.

S&F PVC (SWR) Type-B pipes single socketed, 75mm dia, in any length with rubber ring fixed to walls complete all as specified.Make:- Astral, Supreme, Finolex.

S&F in repair upto 2nd storeyof building PVC (SWR) Type-B pipes single socketed, 75mm dia, in any length with rubber ring joints, on wall , etc complete all as specified.Make:- Astral, Supreme, Finolex.

S&F in repair PVC (SWR) Type-B bends, 75 mm any radius complete all as specified. Make:- Astral, Supreme, Finolex.

S&F in repair PVC (SWR) Type-B bends, 110 mm any radius complete all as specified. Make:- Astral, Supreme, Finolex.

S&F in repair PVC (SWR) Type-B junction single, 75mm (Single T) equal or unequal complete all as specified. Make:- Astral, Supreme, Finolex.

S&F in repair PVC (SWR) Type-B junction single, 110 mm (Single T) equal or unequal complete all as specified. Make:- Astral, Supreme, Finolex.

S&F in repair PVC (SWR) Type-B floor trap, (75mm diameater for outlet in mm), plain with grating including jointing with solvent cement. Make:- Astral, Supreme, Finolex.

S&F in repair PVC (SWR) Type-B multi floor trap with grating including jointing with solvent cement (75mm diameater for outlet in mm) complete all as specified. Make:- Astral, Supreme, Finolex.

Taking up or down 15 mm steel tubing and connections including cleaning for refixing or removal to store.

Taking up or down 20 mm steel tubing and connections including clearing for refixing or removal to store.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 15 mm, all as specified.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20 mm, all as specified.

Re-Fixing old steel only 20 mm tubing and connections in new or old position (wall ceiling, floors etc.)

S&F in repair Concealed Stop Cock Heavy Body Casted Cap 15 mm complete all as specified. Make:- Essco, Cat No:- SQT-514AKN or equivalent in Kohler/ Artize..

S&F in repair angular stop cock with wall flange , cast copper alloy, chromium plated fency type screwed for 15 mm iron pipe, complete all as specified. Make:-Essco, Cat No- SQT-526KN

S&F Stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20mm bore, complete, fixed in repairs all as specified and as directed.

S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated , aluminium rod & high density plastic ball screwed for iron pipe min wt 210 gms.

Vitreous china Orissa pan of pattern, long pan size 580mm x 440mm, with ‘P’ or ‘S’ trap, front or back inlet and integral foot rest complete including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe, and anti siphon pipe, fixed in repairs complete all as specified and directed.

Cutting chases for concealed water tubing and making good cutting not exc. 10 cm girth in brick wall.

S&F in repair Bib Cock cast copper alloy, chromium plated fency type long body with wall flange & aerator Quarter turn fix with iron pipe, 15 mm bore complete all as specified.

S & F in repair 10 ltrs capacity PVC low level flushing cistern, ISI marked of make specified with inlet, float valve and handle including bracket with 32 mm dia PVC pipe 600 mm long and PVC connection 450mm long complete all as specified and as directed Make :- Cera Cat Part No B1010107 or equivalent in kohlar ,jaquar

Grating doom 125mm dia with waste holes of PTMP (minimum weight 40gm).

S&F in repair Wash hand Basin with Fixing Accessories Set, Size : 550 x 400 ,including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC 32mm dia waste pipe, cutting for and pinning in ends of brackets or erecting stand, complete all as specified. Make :- Cera, Essco , Hindware.

Supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 460mm x 405mm x 203 mm bowl size 405mm x 354mm x 203mm complete with waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge. Make: Prayag Cat No- 1216D. & equivalent in Nirali, Jayana.

S & F in repairTubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs

S&F in repair Overhead Shower 100 mm dia Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System complete. Make:- Essco, Cat No-EOS-542N or equivalent in kohlar,jaquar.

E/M Taking down carefully aluminium conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down of unsv MCB DB SPN /TPN along with MCB's

M&L for complete point wiring for One light/fan point controlled by one, one way switch 6 Amp complete with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , terminated into modular galvanised flush boxes of suitable size including white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

All as per srl item No 231 but for One 3 pin socket outlet 6 amp independent

All as per srl item No 231 but for One 3 pin socket outlet 6 amp same board

All as per srl item No 231 above but for one 2 way light point controlled by two 2 way switch

All as per srl item No 231 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

M&L modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

M&L modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

M&L modular type switch, two way 10 Amps, 1 module,240V complete all as specified and directed.

M&L modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

M&L modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

M&L modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

S & F bell push piano flush type polycarbonate material ISI marked 1 module, 6 amps, 240 V. Make:Legrand, HPL , Havells

Supply & fixing only musical door bell ,AC 230 volts Single Phase.

Supply and fixing ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fixing LED tubelight fitting 18-20 W LED, 230V, Batten type complete in all respect . Cat part No DMLN1LT8-16 of Crompton or equivalent Wipro , Havells alongwith LED tubeRod with heat dissipation capability suitable for G-13 base tubelights base fluorescent T8/T12 luminaire , 20 watt LED wattage with colour temp of 5700 K 1800/2000 lumens and with surge arrestor complete in all respect. Cat Part No LTT8-20 of Crompton or equivalent in Wipro , Havells . Note:- The LED batten and LED tube rod shall be of same make.

S & F of lamp holder,PVC /Polycarbonate type with back plate for batten fitting .

S & F LED lamp suitable for B22 holder of capacity 7 Watt.

Supply and fixing Exhaust fan 450 mm sweep, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated complete with louvers for wall mounting incl grouting,making hole in the wall and holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan incl cutting of hole of required size for fixing of the exhaust fan complete all as specified and directed .

Supply and fixing Exhaust fan 300 mm sweep, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated complete with louvers for wall mounting incl grouting,making hole in the wall and holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan incl cutting of hole of required size for fixing of the exhaust fan complete all as specified and directed .

S&F Distribution Board (SPN) double door 4 Way and should be IP 43 protected with Copper Bus bar,Earth Bar ,neutral Bar Door Earthing .

S&F Distribution Board (SPN) double door 8 Way and should be IP 43 protected with Copper Bus bar,Earth Bar ,neutral Bar Door Earthing .

MCB SPN complete 40 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

MCB SPN complete 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

MCB single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series,ISI Marked complete all as specified and directed.

Taking down and Refixing of ceiling Fan ,dismantling blades and depositing Fan and blades in safe custody of user or MES store yard of AGE E/M.as directed by Engr-in-charge

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Supply and fixing in replacement of LED wall mounted tube fitting 10W LED for Mirror (complete fitting)

S & F complete energy saving new generation 10W LED IP65 bulk head luminary with opal diffuser complete all as specified and directed incl LED 10Watt.

MCB single pole 40 Amp with rupturing capacity 10 KA 'C' series,ISI Marked complete all as specified and directed.

S&F sub main wiring with single core cable 2x 10 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1x10 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty electric cable with XLPE insulated screened PVC bedded aluminium stranded conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 16 Sqm x 4 core.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty electric cable with XLPE insulated screened PVC bedded aluminium stranded conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 10 Sqm x 2 core.

Sand cushioning to under ground cable provided with a layer of 8cm deep before laying the cable and 15cm deep after laying and stretching the cable.

Brick covering with width equal to length of brick as mechanical protection to cables with well burnt sub class 'B' bricks laid dry flat all as directed.

Steel tubing galvanized (light grade) 40 mm bore conforming to IS-1239 forpassing cable under road/floor or fixing to poles for protection of under ground cable complete with Flat iron 50x6mm clampsmade to shape and 12mm dia bolts, nuts and washers for fixing where required complete all as directed by Engr-in-Charge

Supplying,installing,testing and commissioning in replacement of existing Main TPN DB, indoor type totally enclosed weather ,dust & vermin proof CPRI approved factory made LT wall mounted meter panel board 415 volt, 3 phase, 4 wires,AC,50 Hz fabricated from 2 mm thick CRCA sheet steel and epoxy powder coating in RAL 7032 shade with seven tank treatment process,front opening hinged door with a fully transparent cover made of polycarbonate/high grade engineering plastic to permit clear view of display,locking arrangement,copper busbar 20 mm x 5 mm insulated with heat shrinkable sleeves, appropriate space for fixing single phase energy meter 04 Nos upto 10-60 amps,40 mm x 40 mm x 6 mm size angle iron frame,hold fast/fastener/bolts/copper lugs/spacers/terminal blocks,rubber gasket,locking knobs,phenolic laminated sheets for live isolation ,heat shrinkable sleeves,nuts,bolts,washers,connections from MCCB to busbar,busbar to meter & meter to MCB with single core copper cable of size 10 sqmm connection , R- Y-B LED indications to show 3 phase availibility at incomer including the following :- (a) One number MCCB 100 Amps , 415 volts,4 pole, 16 KA, thermally adjustable between 70 to 100 % all as specified and directed (b) Temper proof electric meters single phase -04 Nos (Fixing only alongwith sealing, making sticker of Qtr No in suitable size for identification etc all as directed by engr -in charge) (c) Four numbers MCB SPN 32 Amp,10 KA, 'C' series as per indoasian cat ref no. 81150 or equivalent as approved ( one number in each outgoing side of meter)

M/S RAJ ENGINEERS

M/S Sukhmani Construction Co.