Janpad kaushambi ke thana manjhanpur me Hostel Barrack Kshamta 48 Vyakti ke nirmaan karya ke sambandh me Vidhyut Sambandhi Karya

Wiring point for light point/ fan point/ exhaust fan point/ call bell point / Street light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit with modular switch, modular plate, suitable GI Box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C. [D.S.R. No. 1.10.3]

Wiring for twin Control light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit with modular switch, modular plate, suitable GI Box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C [D.S.R. No. 1.11]

Supplying and fixing Suitable size GI Box with modular plate and cover in front on surface or in recess including providing and fxing 3 pin 5/6 A modular Socket outlet and 5/6 A Modular switch connections etc. as required (for plug point) [D.S.R. No. 1.31]

LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy >135 lm/Watt). Supplying, Installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). [D.S.R. No. 8.14.14]

SITC of LT Panel vermin proof floor mounting,MS Channel base with bottom and fabricated out of 2.0/1.6 mm thick CRCA Sheet steel,painted with powder coated paint of shade as per directin of Engineer incharg after proper sheet treatment process of sheet steel.The busbar of pannel shall be electrical grade high conductivity alluminum alloy of appropriate cross section as per rating.The main busbar shall run through uot the pannel rating as main incommer rating.The busbar shall be supported by non hygroscopic SMC/DMC Bus bar support witch shall be mounted on proper interval to ensure the bear the jerks of short circuit os 50ka for pannel having acb as incommer& 36 kA for pannel having MCCB incommers.pannel shall be constructed in fully segregated compartmrnt design for each feeder as per 3 b construction format.The pannel shall be completed in all respect as per IS:8623 Part-2&3.There shall be seprate metering compartment for incomer metering and outgoing metering. All incommer feeder shall be provided with multifunction meterin along with phase imcluding light and other associated component such as C.T.,control MCB,Terminal block etc.and all outgoing feeder 100& above shall be provided with 3 phase ameter along with phase indicating and other associated component such as CT control MCB Terminal block etc .the the feeder above shall be provided as accomondated all measuring instrument shall be digital type & all indicating Light shall be LED type.wiring shall be done from 1100 v GradePVC insulated copper flexible wire .All ACB shall be electricaly operated draw out type with microprocesssor based with O/L,S/C&E/F realease breakingb/withstnd capacity(ICU/ICs/ICW )50 ka or more all MCCB shall be thermal magnetic/microprocessor with O/L.& S/C Protectionalong with required spreaders & Extended rotary handle with pad locking facility of breaking capacity (ICU/ICS)36KS or more All MCB Shall br thermal 10KA 'C' Curve cubicle type switch board shall be CAT-A and B only INCOMING-200Amp.MCCB 1 No. OUTGOING-63 Amp. MCCB 3 No, [D.S.R. No. 20.1.2. B (ii)]

Supply and laying of Aluminium conductor PVC insulated armoured served sheathed 150 Sq.mm. 3.5 Core cables 1100 Volts grade on wall surface as directed by the Engineer-incharge,complete in all respect including excavation and refilling..The armouring of the cable shall be properly connected with the earth conductor by clamp etc. [D.S.R. No. 20a.1.16]