ADDN/ALTN TO 18 ORS MD ACCN OF CERTAIN UNITS AT OLD MD LINE AND PROVN OF 50 X KITCHEN SINK INCLUDING WATER SUPPLY UNDER GE GOLCONDA

Amount

Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground floor) complete all as directed.

M&L 75mm thick plain cement concrete 1 : 3 : 6 mix type C2 (using 40mm graded stone aggregate) as in plinth protection laid in alternative bays and finished even and smooth with out using extra cement including necessary form work.

M & L 75 mm thick PCC 1:4:8 Type D2 (using 40 mm graded stone aggregate) in sub bases, floors and pavings etc.,

M&L 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in floor finished even & smooth without using extra cement all as specified and directed

Demolition of floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises.

Demolition of cement concrete of any description in any position (Reinforced) all as specified and directed

M&L precast reinforced cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in for 50 mm thick kitchen platforms or in manhole covers and jointed/set in cement mortar 1:6 complete all as specified and directed. Note:- (i) Rate shall be inclusive of necessary formwork. (ii) Steel reqd shall be measured and paid separately under relevant item.

M & L Granite (of any type) work (table rubbed and polished) 20 mm thick in steps, jambs, pillars, window-cills, cooking platforms,over and including15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc and grinding the edges to full round complete all spfd and directed.

M&L non skid coloured ceramic floor tiles 7-8 mm thick (square/ rectanglar ) area of each tile exc 0.11 sqm but n'exc 0.18 sqm , set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6.all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm, but n exc. 0.11 sqm, in floor etc. set and jointed in net cement slurry & pointed in white or coloured cement to match over and including 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6 all as specified and directed.

M&L glazed ceramic coloured tiles in vertical surface 375x 250x 7mm thick set and and jointed in cement slurry and pointed with white or coloured cement to match over and including Rendering 10mm thick backing coat in CM 1:4 on fair faces of brick work or concrete surface all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar and disposing the debris outside defence land all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks, old size one brick straight or curved on plan exc 6m mean radius, built in CM 1: 6 all as specified and directed.

M&L for brickwork with sub class B Bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls/ceiling including raking out joints, hacking for keys, scrubbing down with water etc.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete surfaces finished even and smooth without using extra cement

M&L 15mm thick plastering in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement.

M&L 5 mm thick plastering in CM 1:3 finished even and smooth w/o using extra cement on concrete surface of ceilings.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali-resiatant primer on plastered surrfaces complete all as specified.

M&L for preparation of newly plastered surfaces and applying two coats of cement base paint on wall surfaces complete all as specified and directed

M&L for one coats of cement base paint on old surface of wall including preparation of surfaces all as specified and directed.

M & L for one coat of white wash on old surface of ceiling including preparation of surfaces all as specified and directed.

M&L Preparation of old distemper surface of walls and applying one coat of oil bound distemper white or tinted all as specified and directed.

M & L for three coat of white wash on new surface of ceiling including preparation of new surfaces.

Supply only integral water proofing compound complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) n exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm but n exc 4.00 each complete all as specified and directed..

Taking down shutters of any description n. exc. 1 Sqm each complete all as specified and directed..

Taking down shutters of any description exc. 1 Sqm but n exc 2.00 sqm each complete all as specified and directed..

M&L 2nd class hard wood plain straight solid chowkats and frames wrought, framed, rounded, chamfered put together with glue pinned joints all as specified

S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts of size25x3MM MS flat; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0

M&L for cement concrete 1:2:4 type B 1 using 20mm graded stone aggregate in bed black for hold fasts and coping incl necessary form work weathering slighly rounded or chamfered angles and treating and making good the disturbed portion complete all as directed.

S&F Window guard bars, plain, let in wodden frames, L or T section section suppores for shelves etc. and similar articles conforming to Fe 290-0 or Gde E-165

M&Lfactory made 2nd class hard wood plain framed panel shutter 35 mm thick (two or three panels) with lock rail and panel of 9MM BWP Commercial Ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail & style as per IS 1003 (Part-I) Kiln seasoned and chemically pressure treated.

S&F 35 mm thick IInd class hard wood glazed and skelton shutters sizes of members as specified in SSR(Part-I) clause 8.20(a), open rebated and prepared to receive glass or gauge (without sash bars ) edges of framing plain, chamfered or rounded, fitted with cut and miterd beads for securing glass or gauge etc. complete all as specified as directed

S&F 30 mm thick 2nd class hard wood glazed and skeleton shutter of divided into square, with plain chamfered or rounded metred and rebital sash bar any number and framing moulded windows, ventila-tors, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.20 (b) fitted to chowkats complete all as directed.

S&F MS Butt hinges medium weight cold rolled of size 100mm complete all as directed.

S & F Aluminium anodised,barrel tower bolts of extruded section and fixed, length of bolt in 200 mm etc complete all as spfd and directed.

S & F 150 mm length of extruded aluminium alloy handles, fabricated type., anodised complete.

S & F for Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt in 300 mm etc complete all as spfd and directed.

S & F in repairs 300mm, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed

S&F MS Butt hinges medium weight cold rolled of size 75mm complete all as directed.

S & F 150 mm length of aluminium anodised barrel tower bolts of extruded section and fixed complete all as directed..

S & F 100 mm length of extruded aluminium alloy handles, fabricated type., anodised complete all as specified and directed.

S&F mild steel wire type I, gate & shutter, hooks & eyes 150 mm size complete all as directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.4 mm & fixed with stainless steel wire staples fixed all as specified and directed.

M&L preparation of new surfaces of wood or wood based material description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

M&L preparation of old painted surfaces of wood based material description over 10 cm in width or girth applying one coats of synthetic enamel paint complete all as specified and directed.

S&F PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling fixing in opening etc complete all as specified and directed..

M & L factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat molded plain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing at site as per specification and drawing all as specified and directed

S&F 100 MM Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 all as specified and directed.

S & F Aluminium anodized tower bolt of extruded section 150 mm all as specified and directed

S&F in repairs 140 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring all as specified and directed

S&F 3mm thick sheet glass ordinary quality and glazing with wooden beads or oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed.

Supplying and fixing 16 mm of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling including taking down for bore of pipes in 15 mm, steel tubing complete all as specified and directed

Supplying and fixing 20 mm of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling including taking down for bore of pipes in 20 mm, steel tubing complete all as specified and directed.

S&F triple layered Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top )of 500ltr capecity hoisted and fixed in position all as specified including dismantling of old unserviceable water tanks

S&F in repair 15 mm bore Bib taps cost copper alloy Chromium plated with fancy type, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed

S&F in repair 15 mm dia Stop valves, cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for union with long shank and cup

S&F in repair 15 mm dia concealed Stop cock, cast copper alloy screwed down, high pressure, with crutch or butter fly handle, completed all as specified and directed.

S&F CPVC ball valves, with CPVC lever, screwed both ends to pipes of 20mm bore fixed complete.

S & F in repair 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule completed all as specified and directed.

S&F in repair PVC connection 15mm dia, 45 Cms long with brass ferrules on both ends .

S & F Vitreous China wash basin, white, flat back, size 630x450mm including cutting for & pinning in ends of brackets or erecting stand but exclusive of fixing of supply of waste pipe fixed in repairs.

S&F in repair PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe completed all as specified and directed.

S & F in repair 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement completed all as specified and directed.

S & F in repair 40mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement completed fixed in repairs all as specified and directed.

S&F in repair low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 Bore of pipes in 32mm,as in waste pipe etc completed all as spd and directed.

S&F low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 Bore of pipes in 40mm,as in waste pipe etc completed all as specified and directed.

S & F in repair15mm bore fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, swan pipe, screwed for iron pipe completed all as specified and directed.

S & F in repair Vitreous China squatting pan , water closet "Orrissa" pattern size 580 X 440 mm white with integral footrest (excluding flushing cistern & flush pipe complete including provision of cement concrete completed all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, etc complete all as specifed and directed.

S&F stainless steel sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, etc complete all as specifed and directed.

S&F towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190 gms) completed all as specified and directed.

S&F in repair 15 mm dia Brass chromium plated shower rose 125 mm size completed all as specified and directed.

Dismantling of cast iron/AC/PVC pipes100/110mm dia, jointed in cement mortar and taking out of trenches if required

Dismantling of cast iron/AC/PVC pipes 75 mm dia, jointed in cement mortar and taking out of trenches if required

Excavation in trenches n.exc 1.50m wide and n.exc. 1.50 m depth and getting out in hard/dense soil.

Returning, filling in incl spreading, leveling, watering and well ramming in layers n. exc 25 cm completed all as specified and directed.

Removing excavated materials n'exc 50 mtr and depositing where directed at a level n. exc 1.5 mtr above the starting point in soils completed all as specified and directed.

M&L PCC 1:3:6 type C2 (using 40 mm graded crushed stone stone aggregates) for providing concrete bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 75/100 mm bore pipe in complete all as specified and directed.

S & F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, bore of pipe in 110 mm, etc complete all as specifed and directed.

All as per item No. 83 above but fixed to walls. (At any height of building, till 4 floors also) completed all as specified and directed..

S & F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, bore of pipe in 75 mm, etc complete all as specifed and directed.

All as per item No.85 above but fixed to wall. (At any height of building, till 4 floors also) completed all as specified and directed..

S&F in repairs 110 mm bore PVC( SWR ) bend with oval access doors, completed all as specified and directed.

S&F in repairs 75 mm bore PVC( SWR ) bend with oval access doors, completed all as specified and directed.

S & F for PVC (SWR) vent cowl, bore of pipe in 110 mm, etc complete all as specifed and directed.

S&F PVC (SWR) bends (size of bore 110mm)

M & L for PVC (SWR) floor trap, plain with grating including jointing with solvent cement, diameter of outlet in 75 mm bend, etc complete all as specifed and directed.

S&F in repairs salt glazed stone ware gully traps square or rounded mouthed tape & fix 150 x 150 mm fixed in cement concrete complete all as specified and directed.

S&F 6 mm thick Non -asbestos Fibre reinforced cement corrugated sheet in roof, fixed with J or L hook or cranked bolt with washers complete including dismantling of old AC sheet (Corrugated/Semi-corrugated) in roof covering all as specified and as directed.

S&F 6mm thick Non -asbestos Fibre reinforced cement corrugated sheet two pieces adjustable serrated ridge fixed with J or L hook or cranked bolt with wahsers complete all as specified and as directed..

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof padding with WPC complete all as specifed and directed. (NOTE : Supply of WPC will be paid under the respective Item)

M&L for APP based polymeric membrane minimum weighing 3Kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm laid over primed surface including bituminious primer conforming to IS -3384 applied @ 0.3 ltrs/sqm by forced application over finished with one coat of aluminium paint @ 100 ml/Sqm, 10 cm overlap fused uniformly by LPG torch flame, including rendering 10mm thick in cm 1:4 on concrete surfaces of roofs, parapet etc. finishing to surfaces even and smooth without using extra cement and provinding necessary slope with using WPC @ 3% by weight of cement complete incl taking down existing roof treatment and cement plaster of any description, roughing, preparing the surface by cleaning the surface with wire brushing scrubbinbg down with water to receive new treatment all as specified and directed.

M&L for Reinforced cement concrete as in shelves,chajja and the like of type B-1 (1:2:4) complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slab, floor slab. Shelves etc finished fair surface all as specified and directed..

All as per item no- 98 but to sides of slab, shelves etc exc 5 but not exc 10 cm wide all as specified and directed..

Mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed.

Ditto but 5mm dia and over upto and including 10mm dia as in reinforcement, cut to length, bent to shape required including cranking binding with mild steel wire (annealed) not less 0.9 mm dia complete all as specified and directed.

BLANK

S&F stainless steel plate rack made out of stainless steel (Non magntic type) of 22 gauze sheet of size 36" x 30"x 10" all as specified.

Supplying and fixing 20 mm of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling complete all as specified.

M & L for Bib taps, cast copper alloy with crutch or butterfly handle, chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed, Bore dia of pipe in 15 mm, etc complete and S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) all as specified and directed.

M&L Cement concrete 1:4:8 Type D 2 (using 40 mm graded aggregate, in foundations, filling and mass concrete complete all as specified and directed.

M&L for hardcore of broken stone or boulder gauges n.exc. 63mm deposited spread and leveled in layer n.exc. 15 cm thick watered and rammed and true surface.

M&L 25 mm thick PCC 1:2:4 type B1 using 12.5mm graded stone aggregate as in floor finished even & smooth without using extra cement all as specified and directed.

BLANK

Cutting into existing manhole for connecting new drain of 75 mm bore pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1, smooth finished, reforming benching as required all as specified and directed.

M & L for three coat of white wash on new surface of wall including preparation of new surfaces all as specified.

Taking down carefully existing point wiring of any description for (light, fan ,sockets bells etc) complete including fittings such as sunken boxes, switches, sockets, ceiling rose, lamp holders, brackets ,fittings, pendants, fan regulartors etc and making good the disturbed surface of walls, floors etc. all as specified and directed.

M&L Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including PVC rigid conduit with all fittings for concealed type on stone / brick, masonary walls, roof etc including new CI/MS sunken box of required size and all as directed by Engineer-in-Charge & 3 mm thick plastic laminated sheet for housing switches sockets, regulators etc. including cutting/running chases, pinning in and making good the disturbed surfaces to match with the existing specification, complete all as specified and directed at site .

All as per item no.113 but One 3 pin 5/6 Amps switch socket outlet on independent board complete all as specified and directed by the Engr-in-charge.

All as per item no.113 but One 3 pin 5/6 Amps switch socket outlet on same board complete all as specified and directed by the Engr-in-charge.

All as per item no.113but for One 3 pin 15 / 16 Amps switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed by the Engr-in-charge.

M&L switch piano flush type single pole one way 5 Amps complete all as specified and directed at site.

M&L switch socket combination flush type 5 Amps Multipurpose 2 in 1, 3 pin/5 pin with porcelain base complete all as specified and directed at site.

M&L Switch socket combination 2 in 1 flush type universal 3 pin 5 & 15 Amps complete all as specified and directed at site.

M&L lamp holder insulated body with back plate suitable for battern fittings complete all as specified and directed at site.

S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminals complete all as specified and directed at site.

M&L Fan Regulator (Rotary step type, Switch/Socket type Dimmer) 230/240V, AC complete all as specified and directed at site.

M&L Bell push, flush type, 5 Amps complete all as specified and directed at site.

M&L bell Ding Dong AC, 230 V single pole all as specified complete all as specified and directed at site.

S&F 9 W LED bulb of base B22d with color temp 6500K all as specified and directed.

S&F in repairs sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 8 Ways, double door complete all as specified and directed at site.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

S&F Led Tube light fitting 20W, 220V,AC Aluminium Extruded channel ,Decorative tape including driver and accessaries

S & F LED light fittings, 1x10 watts bulk head luminaires etc complete with all accessories and including connecting up with twin core twisted flexible PVC copper conduct cabe of 23/0.0076 from ceiling rose all as specified

M&L for Submain wiring with two single core PVC (FRLS) insulated flexible copper conductor cable of size 6 Sqmm and one single core PVC (FRLS) insulated unsheathed flexible copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including PVC conduit medium grade/casing caping with all fittings suitable for concealed/surface type and making good the disturbed wall surfaces to match with existing specification all as required at site including taking down existing sub main wiring /Service wire of any description and size including earth wire, batten, conduits and making good the disturbed surfaces of walls, floors etc. complete all as specified and directed at site.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.3 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead complete all as specified and directed by the Engr-in-charge. :- Note :-Item of Earthing includes cost of earth work, 7.5m long galvanised iron earth lead 4mm size and protection pipe of 15mm bore GI light grade

Supply and laying or fixing or passing through pipe 1100 volt grade heavy duty cable with PVC Insulated aluminium conductor served with an inner sheathing of PVC Tape armoured with galvanised steel wire or tape and over all PVC Sheathed 2 Core10 sq mm nominal cross section in service connections including taking down existing /Service wire of any description and size including earth wire, batten, conduits and making good the disturbed surfaces of walls, floors etc.

Sri Associates

NAVANAND ENTERPRISES

BUILDWEL

STANDARD AGENCIES