REPAIR MAINTENANCE RESURFACING OF ROAD FURNITURE AT OUTLAYING AREA, STEEL YARD, ROBERT COMPLEX, WNC (O) MESS AND INS SHIKRA UNDER AGE B R-II UNDER GE (NW) NOFRA

Amount

Scarifying or packing gravelled, macadam or bituminioussurfaces in area n.exc.400 Sqm and depth exc 50 mm & n.exc 150 mm deep including removal from ste of work complete all as specified and directed.

M & L for 7.5 cm thick (compacted thickness) WBM, with coarse aggregates of granite, trap or basalt of grading 2 (63 to 45 mm size) or of grading 3 (53 to 22.4 mm size), spread, rolled and compacted to required gradient and camber with three wheel-power roller of 80 to 100 kN capacity or an equivalent vibratory roller complete all as specified and as directed.

Ditto- all asper item No 2.00 above but except material Note;- Service material obtained from Item No 1.00 shall be re used.

Repair to pot holes any depth n.exc 1 Sqm each including sweeping free from dust and mud, or water scoring sunken surfaces in roads, paths, etc. cutting around edges to atleast 25mm in depth, making good by filling in screened and graded road metal watering and well ramming including supply of road metal complete all as specified.

Material & Labour for preperation of new bituminous surfaces by wire brushing for removing caked mud etc sweeping with brooms and finally fanning and cleaned the surface with gunny bags to remove all loose dirt etc amd applying evenly a priming tack coat with bituminous primer at 10 Kg per 10 Sqm using paving bitumen on unsurfaced water bound macadam complete all as specified and directed .

Ditto- all asper Item No 5.00 above but on existing black top surfaces applying evenly a priming tack coat with bituminous primer at 05 Kg per 10 Sqm using paving bitumen on unsurfaced water bound macadam complete all as specified and directed .

Material & Labour for Bituminous premix asphaltic semi dense concrete 40 mm consolidated thickness by using paving bitumen VG-30 grade with 6 % binder content by weight of total mix , laying with mechanical paver, rolled and compacted to required camber and gradient by using 8 to 10 tonne capacity power roller complete all as specified and directed. Note- i) Semi dense bituminous concrete shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. ii) The exact bitumen content required shall be determined following the Marshall mix design procedure contained in the Asphalt Institute Manual MS-2 ( Sixth Edition) as referred in case 3.5.3 of IRC 111: 2009, The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of Rs 60.00 per Kg. No claim whatsoever shall be made for adjustment in plus side.

Material and labour for premix bituminous macadam 75 mm consolidated thickness by using paving bitumen VG-30 grade with binder content @ 4% by weight of total mix, laying with mechanical paver, rolled and compacted to required camber and gradient by using 8 to 10 tonne capacity power roller complete all as specified and directed.

Material & Labour for preparation of black bituminous road surfaces by removing all loose dirt, dust etc and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete all as specified and as directed.

S & F solar road studs of size not less than 125X 125 X 25 mm made of weather resistance aluminium alloy and poly carbonate material electronically welded micro- prismatic lens with abrasion resistant coating as approved by the Engineer in charge. The cats eye shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35⁰ ± 5⁰ to base. The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM E: 809 as recommended in BS: 873 part 4 :1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. The solar panel shall be high efficiency mono crystalline 2.5 V/60 m A and the battery shall be one Ni-mh type (1.2 V/1200 m Ah) high temp for backup of 36 hours full charging. The flash frequency shall be 60 ± 5 times per minute.

M&L for raising and repair sewage chamber of any size with brick work , rendering in cement mortar 1:4 with WPC 3% by weight of cement including cast iorn cover with frame workof suitable size , cover not less than 300 Kg/Each including fixing in position and applying black bituminous anticorrossive paint complete allas specified and directed by Engineer-in-Charge..

S & F Manufacturing, supplying and fixing retro reflective Mandatory/Regulatory sign boards of 900 mm diametre with support length of 3750 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting confirming to type-IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual),symbols and boarders etc.as per IRC, 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure confirming to class- 2 of ASTM- D- 4956-01and fixing the same with suitable sized aluminium alloy rivets @ 20 cm C/C to back support frame of MS angle iorn of size 25X25X 3 mm along with theft resistant measures, mounted and fixed with 2 Nos, MS angles of size 35X35X5mm to a vertical post made up to MS Tee section ISMT 50 X50XX6 mm welded with base plate of size 100X100X5 mm at the bottom end and including making holes in pipes angle flats, providing and fixing MS measage plate of requied size, steel work to be painted with two or morre coats of synthetic enamel paint of requied shade and of approved brand & manufacture over priming coat of zyinc chromate yellow primer (vertical MS -Tee support to be painted in the black and white colour) . Back side of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lift etc. Complete all as per specified and directed.

S & F Manufacturing, supplying and fixing retro reflective cautionary/warning sign boards of equlateral triangular shape having each sides of 900 mm with support length of 3650 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting confirming to type-IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual),symbols and boarders etc.as per IRC, 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure confirming to class- 2 of ASTM- D- 4956-01and fixing the same with suitable sized aluminium alloy rivets @ 20 cm C/C to back support frame of MS angle iorn of size 25X25X 3 mm along with theft resistant measures, mounted and fixed with 2 Nos, MS angles of size 35X35X5mm to a vertical post made up to MS Tee section ISMT 50 X50XX6 mm welded with base plate of size 100X100X5 mm at the bottom end and including making holes in pipes angle flats, providing and fixing MS measage plate of requied size, steel work to be painted with two or more coats of synthetic enamel paint of requied shade and of approved brand & manufacture over priming coat of zyinc chromate yellow primer (vertical MS -Tee support to be painted in the black and white colour) . Back side of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lift etc. Complete all as per specified and directed.

Frends Enterprises (BID ID -3511849)

RS Enterprises (BID ID -3505966)

SATGURU ENTERPRISE (BID ID -3505983)

m/s ashoka enterprises (BID ID -3506766)

MUKESH CONSTRUCTION CO (BID ID -3506081)

RAJENDRA CONSTRUCTION (BID ID -3504768)

SHRI SAI ENTERPRISES (BID ID -3502185)