Construction of Municipal Council Office Building Shopping Including Car Parking, Sanitary Fitting, Water Supply, Drainage System (Complete Job) at Hadda Pond Kishtwar. 2nd time

Amount

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 in all kind of soil (Including all leads lifts, & carriages)

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge in all kind of soil (Including all leads lifts, & carriages)

Extra for every additional lift of 1.5 M or part therefore in all kinds of soil. (Including all leads lifts, & carriages)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed. (Including all leads lifts, & carriages)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including Admixtures in recommended proportions, (as per IS 9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge All work upto plinth level. (Including all leads lifts, & carriages)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including Admixtures in recommended proportions, (as per IS 9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge All work above plinth level upto floor V level. (Including all leads lifts, & carriages)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto plinth level in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). (Including all leads lifts, & carriages)

Providing and laying DPC 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) and curing complete. (Including all leads lifts, & carriages)

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. (Including all leads lifts, & carriages)

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 fine sand). (Including all leads lifts, & carriages)

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:6 (1 cement : 6 fine sand). (Including all leads lifts, & carriages)

Extra for brick work in super structure above plinth level upto floor V-level (Including all leads lifts, & carriages).

Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand). (Including all leads lifts, & carriages)

Extra for half brick work in super structure above plinth level upto floor V-level. (Including all leads lifts, & carriages)

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars. (Including all leads lifts, & carriages)

12mm thick cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement : 3 fine sand). (Including all leads lifts, & carriages)

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand). (Including all leads lifts, & carriages)

15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand). (Including all leads lifts, & carriages)

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 6 fine sand). (Including all leads lifts, & carriages)

15mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating cost of neat cement on the rough side of single or half brick wall. (Including all leads lifts, & carriages)

Extra for plastering exterior walls of the height more than 10 Mtrs from ground level for every additional height of 3 Mtrs or part thereof. (Including all leads lifts, & carriages)

Making of grove 12mm x 10mm between brick and RCC. (Including all leads lifts, & carriages)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size below flooring, retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing. (Including all leads lifts, & carriages)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50Mt & lift upto 1.50M. (Including all leads lifts, & carriages)

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete. (Including all leads lifts, & carriages)

Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections. (Including all leads lifts, & carriages)

Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed. (Including all leads lifts, & carriages)

Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75mm including grouting with cement mortar 1:4 (1 cement : 4 fine sand). (Including all leads lifts, & carriages)

Centering and shuttering including strutting, propping etc. and removal of form work for :- (Including all leads lifts, & carriages)

Foundations, footings, bases of columns. (Including all leads lifts, & carriages)

Columns, pillars, piers. (Including all leads lifts, & carriages)

Lintels, beams, plinth beams. (Including all leads lifts, & carriages)

Suspended floors, roofs, landings and access platforms. (Including all leads lifts, & carriages)

Edges of slabs and breaks in floors and walls upto 20cm wide. (Including all leads lifts, & carriages)

Stairs (excluding landings) except spiral stair cases. (Including all leads lifts, & carriages)

Wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc. (Including all leads lifts, & carriages)

Weather shades, chajjas, corbels etc. including edges. (Including all leads lifts, & carriages)

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 mtr. of part thereof (Plan area to be measured). Suspended floors, roofs landing, beams and balconies (Plan area to be measured). (Including all leads lifts, & carriages)

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc. (Make Armocreate of SWC Chryso France) consisting of (a) applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining was upto 300mm height including rounding of junction of walls and slaps. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. (iv) Finishing the surface with 20mm thick joint less cement mortar of mix 1: 4 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm / sq 3mm deep. (e) The whole terrace so finished shall be flooded with water far a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurras as 65mm. (Including all leads lifts, & carriages)

Providing and laying water proofing treatment (Make Armocreate of SWC Chryso France) to vertical and horizontal surface of depressed portions of W.C., kitchen and the consisting of (i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surface. (iii) III course of applying blown or / residual bitumen applied hot at 1.7 kg per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm. (Including all leads lifts, & carriages)

Providing and laying matt finished HEAVY DUTY VITRIFIED TILES of size 1200X600mm with thickness ranging from 10mm to 12mm having water absorption less than 0.08% and conforming to IS: 4457 of approved make In Nitco,Somany, Kajaria in all colours and shades in Platform series,capsule series,Tactile Series Or In digital prints as per the Requirment of user outdoor floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge. (Including all leads lifts, & carriages)

Providing and laying glossy finished vitrified ULTRA CHARGE TILES PRM QUALITY floor tiles of 120x60cm sizes (thickness to be specified by the manufacturer but not less than 10mm) with water absorption less than 0.08% and conforming to IS : 15622 of approved make of Somany, NITCO and Kajaria make in colours and shade Dacia Series, Crown series, Nuvaro series and Luciano series with the combination of light and dark color laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with matching Epoxy OR Grouts of Make Somany,Nitco, Kajaria etc. complete. (Including all leads lifts, & carriages)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (Including all leads lifts, & carriages)

Providing and laying 16mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. (Area of slab upto 0.5 sqm) (Including all leads lifts, & carriages)

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. (Including all leads lifts, & carriages)

Extra for providing opening of required size and shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete. (Including all leads lifts, & carriages)

Providing and fixing Ceramic glazed floor tiles (Anti skid) 600x600mm of PRM Quality conforming to ISO : 13006 of NITCO, SOMANY, KAJARIA with Water absorption <6% of color and shades In Aegis series, Champion series, Fence series IN SLIP SHIELD laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete. (Including all leads lifts, & carriages)

Providing and fixing PRM Quality Ceramic Glazed wall tiles of Size 300x600 mm conforming to IS : 15622 of minimum thickness 7mm with water absorption < 20% of approved make like NITCO,SOMANY, KAJARIA in all colour and shades in Sierra series, Sterno series, Vivo series, Diano series, Perlino series, Aleta series, Arian series, Edric series, Elemento series, Julian series over 12mm thick bed of cement mortar 1:3 (1cement : 3coarse sand) and jointing with grey cement slurry @ 3.3Kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (Including all leads lifts, & carriages)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing and panelling to be paid for separately). (Including all leads lifts, & carriages)

For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns)(2.60mm or 12 gauge). (Including all leads lifts, & carriages)

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coated 50 microns)(2.60mm or 12 gauge). (Including all leads lifts, & carriages)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5.50 mm thickness (weight not less than 13.75 kg/sqm). (Including all leads lifts, & carriages)

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. (Including all leads lifts, & carriages)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge with brass cover plate. (Including all leads lifts, & carriages)

Providing and fixing structural glazing on required portion of the building with aluminium section (12 gauze using 5.5mm toughen glass with all necessary fittings) as per direction of Engineer-in-charge. (Including all leads lifts, & carriages)

Providing and fixing aluminium composite panel with specific aluminium channel as per approved make with 4mm thick aluminium composite sheet and joint filling with silicone complete as directed by Engineer-in-charge. (Including all leads lifts, & carriages)

Providing and fixing aluminium tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. (Including all leads lifts, & carriages)

Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. (Including all leads lifts, & carriages)

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter. (Including all leads lifts, & carriages)

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion :- (Including all leads lifts, & carriages)

Coupler 110mm.

Single tee with door 110 x 110 x 110mm.

Bend 87.5* 110mm.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters .1 80x1.25 mm M.S. laths with 1.25 mm thick top cover (Including all leads lifts, & carriages)

Providing and fixing ball bearing for rolling shutters. (Including all leads lifts, & carriages)

Providing and fixing aluminium sliding door bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 300x16mm. (Including all leads lifts, & carriages)

Providing and fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper. (Including all leads lifts, & carriages)

Providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087, finished with a coat of aluminum primer on both sides & edges, including two coats of synthetic enamel paint of approved quality on xposed face, fixed to a grid made out of anodized aluminum (with 15 micron anodic coating) Tsections 35 x15x1.5 mm size main runners, cross runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600x1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of zinc chromate yellow primer (aluminum frame work shall be paid separately). (Including all leads lifts, & carriages)

P/F stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc. (Including all leads lifts, & carriages)

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.). (Including all leads lifts, & carriages)

Steel work welded in built-up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, railings, brackets, gates and similar work. (Including all leads lifts, & carriages)

Providing and fixing of 12mm thick GRC wall Cladding (Tiles) of pattern stone castle (size 4” x 10”) on exterior wall / surface. Unistone make as per the approved sample. All complete as per architectural drawings and the directions of Engineer-in-Charge. (Including all leads lifts, & carriages)

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacture,over the plasterted wall surface to prepare the surface even and smooth complete (Including all leads lifts, & carriages)

Finishing wall with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm) (Including all leads lifts, & carriages)

Finishing walls with textured exterior paint of required shade on New work (two or more coats Rustic Regular of any colour as per Engg. incharge) over and including base coat of exterior primer applied @ 3.00kg/10sqm. (Including all leads lifts, & carriages)

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work. (Including all leads lifts, & carriages)

Applying priming coat with ready mixed pink or grey of primer of approved brand and manufacture on new work (Including all leads lifts, & carriages)

Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. (Including all leads lifts, & carriages)

Structural steel work welded in built-up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Riveted and bolted. (Including all leads lifts, & carriages)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal / vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63mm thick with zinc coating not less than 275gm/sqm. (Including all leads lifts, & carriages)

Providing ridges or hips of width 60cm overall width plain G.S. Sheets fixed with polymer coated J or L hooks, bolts and nuts 8mm dia G.I limpet and bitumen washers complete. 0.63mm thick with zinc coating not less than 275gm/kg (Including all leads lifts, & carriages)

Providing and fixing wind ties of 40x6mm flat iron section. (Including all leads lifts, & carriages)

Plumbing SUB HEAD - I : SANITARY FIXTURES Providing and fixing water closet squatting pan (Indian Type W.C Pan) with 100mm sand cost iron P or S trap, 10 ltrs low lewel PVC flushing cistern including flush pipe (Hindware make Cat No. 20070/ Kerovit make Cat No. 606) Manually controlled device (Handle lever) conforming to IS : 7231, with all fitting and fixture complete including cutting and making good the wall and floows wherever required. Orissa Pan white viterous china pan of size 580x440mm with integral type footrests. (Including all leads lifts, & carriages)

Providing & fixing of white vitreous China pedestial type water closet (European Type) with cistern (A/PHAS-100 Cat No. 201100+Cat No. 21054 / Kerovit model No. 112 and flush tank model no. 1001) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge. (Including all leads lifts, & carriages)

Providing & fixing of white vitreous china under counter oval wash basin/circular basin (Hindware 10080 / Kerovit model No. 206 & 207) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge. (Including all leads lifts, & carriages)

Providing & fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008 + Ped Cat No. 11003 / Kerovit model No. 234 Ped Model no. 305) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge. (Including all leads lifts, & carriages)

Providing and fixing CP single liver extended basin mixer (height 85mm) without Popup waste system with 450mm long Braided Hoses and brass nuts with all fittings and accessories as per direction of Engineer-in-charge (Jaquar FUS 290238). (Including all leads lifts, & carriages)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink without drain board 610 x 460 mm bowl depth 200 mm (Pantry) (Including all leads lifts, & carriages)

Kitchen sink with drain board 510 x 1040mm bowl depth 225mm (Dry Canteen/Kitchen). (Including all leads lifts, & carriages)

Providing and fixing, testing and commissioning of C.P. brass single hole sink mixer with CP wall flange, swinging spout complete as required and making good as per direction of Engineer-in-Charge (Jaquar Cat No. CQT-23167D) (Including all leads lifts, & carriages)

Providing & fixing C.P. hand spray with lever control (health faucet) (Jaquar Cat. No. ALDCHR-565 / Kerovit make KA580001) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge. (Including all leads lifts, & carriages)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore (Make Jaquar CQT 23059 / Kerovit make Cat No. KB 1511003). (Including all leads lifts, & carriages)

Providing & fixing C.P. brass robe hook (Jaquar Cat No. ACN 1191N) or approved equivalent) fixed to wall/door with plastic rawl plugs and C.P brass screws including cutting and making good the walls wherever required as per direction of Engineer-Incharge. (Including all leads lifts, & carriages)

Providing & fixing recessed liquid soap dispenser (Jaquar Cat No. ACN 1135N) as per direction of Engineer-Incharge. (Including all leads lifts, & carriages)

P/F of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat No. ACN 113 N). (Including all leads lifts, & carriages)

Providing and fixing of Tumbler Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat ACN 114 N). (Including all leads lifts, & carriages)

Providing and fixing Bottle Trap (Jaquar Cat No. ALD. 769L) and other ancillary fittings. Cutting and making good the walls wherever required compete as per directions of Engineer-Incharge. (Including all leads lifts, & carriages)

Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat. no. 70002) comprising of EWC - P , Cistern, Seat Cover, Twin Flush Fittings, Wash Basin 450x300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge. (Including all leads lifts, & carriages)

Providing and fixing 6mm copper backed float glass mirror MODI / SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative, etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer in charge. (Including all leads lifts, & carriages)

Providing and fixing CP brass towel rail of approved make complete with CP brackets fixed to wooden cleats with CP brass screws.(Jaquar Cat No. ACN1111DNM / Kerovit make Cat No. KA 930001). (Including all leads lifts, & carriages)

P/F brass towel ring round with round flenge of approved make complete with all fittings (Jaquar Cat No. CAN 11021 BN / Kerovit make Cat No. KA 930004). (Including all leads lifts, & carriages)

Providing and fixing of glass shelf 600m long with all C.P fittings of approved quality complete item (Jaquar Cat No. ACN 11071 N). (Including all leads lifts, & carriages)

Providing and fixing toilet paper holder with all fittings Jaquar Contienal ACN 1153 N. (Including all leads lifts, & carriages)

Providing and fixing 15 mm dia. C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (Short Body) (Make Jaquar Cat No. CQT-23047) (Including all leads lifts, & carriages)

P/F of regular body concealed stop cock suitable for 15mm pipe line with protection cap (Jaquar Cat No. ALD 083 / Kerovit make Cat No. KB 111030 CP and exposed part Cat No. KB 1511032) with exposed part angular stop cock with flange FUS 29.53. (Including all leads lifts, & carriages)

Providing and fixing of wall mixer with provision for overhead shower with 115mm long bend pipe on upper side connecting legs and wall flanges of approved quality with all fittings (Jaquar cat no SHA-479L). (Including all leads lifts, & carriages)

Providing and fixing of wall mounted over head shower 200m dia (Jaquar DHS-CHR-1613) with shower arm 450mm long round shape with 90 degree bend with flanges (Jaquar SHA-479L450) with all fittings. (Including all leads lifts, & carriages)

Sub Head- II-Water Supply Internal work:- Exposed on wall Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps, including cutting and making good the walls etc. (Including all leads lifts, & carriages)

25mm dia. Nominal bore (Hot water supply)

32mm dia. Nominal bore

40mm dia. Nominal bore

Conceal Inside the walls:- Providing and fixing Conceled pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. (Including all leads lifts, & carriages)

20mm dia. Nominal bore

20mm dia. Nominal bore (Hot water supply)

External work Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps, including cutting and making good the walls etc. (Including all leads lifts, & carriages)

20mm dia. Nominal bore

25mm dia. Nominal bore

32mm dia. Nominal bore

40mm dia. Nominal bore

Supplying thermal insulation over hot pipes with 6mm thick "Kaiflex" or Careflex or approved equivalent thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber having density of 60-90 kg/m3 over pipes of following sizes including all required accessories complete as per manufacture's specifications and finishing it as per site requirement with cement plaster of 1:3 (1 cement: 3 coarse sand). (Including all leads lifts, & carriages)

20mm dia 9mm thickness

25mm dia 9mm thickness

SUB HEAD - III : DRAINAGE SYSTEM Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed. (Including all leads lifts, & carriages)

Providing and fixing un-plasticised PVC pipe clips of approved design to un-plasticised un-plasticised rain water pipes by mean of 50X50X50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (Including all leads lifts, & carriages)

75MM pipe

110MM pipe

160MM pipe

Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate) (Including all leads lifts, & carriages)

Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. (With F.P.S. bricks) (Including all leads lifts, & carriages)

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked) (Including all leads lifts, & carriages)

Providing and fixing heavy class SS grating plane including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge (Size 100 mm dia) (ISI Marked) (Including all leads lifts, & carriages)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) (1000 ltr. Capacity 15 No.). (Including all leads lifts, & carriages)

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks. (Including all leads lifts, & carriages)

SUB HEAD - WATER SUPPLY, DRAINAGE, PUMPS & EQUIPMENT Supply, assembly, erection, testing and commissioning of pumping system comprising the following: Vertical/Horizontal centrifugal pumps (1 Working + 1 Stand-by) with mechanical seal, SS Volute casing and SS impeller connected to suitable capacity TEFC induction motor suitable for 415 ± 10 % volts, 3 phase, 50 cycles A.C. supply with 100 mm dia. pressure gauges including MS skid and mounting of the pumps on the skid. (Motor to be of the same make as the pump) (wilo,ebara and matherplatt etc.) (Including all leads lifts, & carriages) (Including all leads lifts, & carriages)

Pump Capacity 180 lpm, at 30 m head (1 working + 1 standby) (Domestic water relift pump). (Including all leads lifts, & carriages)

M/S A L CONSTRUCTION

PARDEEP KUMAR AND CO