SPL REPAIR TO BLDG NO KP 1/7 (QTR NO 33 TO 40), Bldg No EN 03 TOTAL 08 QTRS NO 03/17 TO 03/24 AND CS III/5 AND 6 AND CSIII/10 AND 11 AT VARIOUS LOCATIONS AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - A] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteneners 12.5mm dia and 40mm long, including dismantling of wall and ceiling boardscomplete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, including dismantling of wall and ceiling boards complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.(ii) Aluminium frame work shall be measured and paid for separately.

Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc and brushing neat cement slury with 3kg/sqm, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

all as per above item no 10 here-in-before but in vertical surface such as skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:3), complete all as specified and and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

S & F for 25mm thick factory made flush shutters, solid core construction with block board core playwood face panels, commercial type on both sides kiln seasoned and chemically pressure treated with anti termite complete all as specified and and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:3), complete all as specified and and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter complete all as specified and as directed.

M&L for granite (of any type) 20mm thick (Table rubbled and mirror polished ) in steps, jambs, pillars, window-cills, cooking platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 20mm thick screed bed in CM (1:4), complete all as specified and directed.

M&L for 20 to 25mm thick Machine cut kota stone slabs as in flooring, laid over and including 20mm thick screed in cm (1:6), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed.

M&L for 20 to 25mm thick Machine cut kota stone slabs as in riser of step, skirting, dado etc. laid over and including 10mm thick backing layer in cm (1:4), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed .

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks(old size), straight or curved on plan to any radius in half brick walls built in Cement morter (1:4), complete all as specified and directed

M&L for Brickwork with fly as Bricks(old size), straight or curved on plan exc 6m mean radius built in Cement morter (1:6), complete all as specified and directed

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for rendering 5 mm thick in cement mortar (1:3), on concrete surfaces of ceiling , finished even and smooth without using extra cement, complete all as specified and directed.

Supply only integral water proofing compound, complete all as specified and as directed.

M&L for complete removal of existing treatement and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistane, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on old surfaces. complete all as specified

Material & Labour for preparation of new plastered surface of walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparing new plastered surface of walls and applying two coat of oil bond distemper, white or any tint, over a coat of primer over 1 mm thick wall care Putty etc complete as specified and directed.

M&L for newly plastered surfaces on wall and applying Three coat of white wash complete all as specified and as directed

&L for newly plastered surfaces on ceilling and applying Three coat of white wash complete all as specified and as directed

M&L for preparation of old plastered surfaces on ceilling and applying One coat of white wash complete all as specified and as directed

M&L for complete removal of existing treatement of internal wall and appying two coat of oil bound distemper over 1 mm thick wall care putty including a coat of alkali resistant priming paint etc complete all as specified and as directed

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Use & Waste of formvwork to soffits of suspended slabs such as roof, floor,slabs, landings etc n.exc 200mm thick (horizontal or sloping) for rough finished surfaces of concrete complete all as specified and direct

M&L for R.C.C (20 mm graded aggregate type B1 in 1:2:4 ) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc all as specified and directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

Demolition of cement concrete (un-reinforced ) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for 75mm thick pcc type C-2, 1:3:6 (using 40 mm graded aggregrate) as in sub base of floor finishing cement concrete surface even and fair Without using extra cement. Complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C2 (using 20mm graded crushed stone aggregate), as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of (3:1), complete all as specified and directed.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed with neat cement slurry in floorsand pointed with pigment to match the shade, including 15 mm thick screed bed in CM 1:6. Complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat, coping and the like including necessary form work, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsite the premises, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F Factory made 30mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and shown on drawing for SI No. 08095 on Srl Page No. 180 of SSR (Part-II) and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,, complete all as specified and shown on drawing for SI No. 08080on Srl Page No. 176 of SSR (Part-II) and as directed.

S&F 100mm size stainless steel butt hinges, medium weight, cold rolled, mild steel, complete all as specified and as directed.

Dismantling timber scantlings ( framed works) 40 sq. cm and over in section, in any position, complete all as specified and as directed.

M & L for 2nd class hardwood in plain, solid, straight chowkats and frams wrought, framed rebated onnthe solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

M&L in repair 18/19 mm thick Pre laminated interior grade both sides laminated with decorative choice laminations fixed with screw to timber frame as in cupboard shutter, shelve, kitchen cabinet etc complete all as specified and as directed and as directed.

M&L in repair 18/19 mm thick Pre laminated exterior grade both sides laminated with decorative choice laminations fixed with screw to timber frame as in cupboard shutter, shelve, kitchen cabinet etc complete all as specified and as directed

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed

S & F ball catches with 8mm dia steel ball, abd brass body and skriking plate including letting in and fixed complete all as specified and as directed

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 75 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 200 mm long of extruded section, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 150 mm long of extruded section, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 100 mm long of extruded section, complete all as specified and as directed.

S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc of 25 mm bore complete all as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

S&F 4mm thick sheet glass of ordinary quality and glazing for Aluminium Joinery, in squares n.exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F 4mm thick one side frosted glass of ordinary quality and glazing for Aluminium Joinery, in squares n.exc 0.50 sqm in each pane, complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

M&L preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

M&L preparation of old painted surfaces of steel surfaces of any description not otherwise described over 10 cm width or girth and applying One coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

S&F in repair rotational moulded polyethylene water storage tank 500ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, including dismantling of existing water tank complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 210 grms), complete all as specified and as directed.

S & F Waste fittings, brass, 32mm bore chromium plated for glazed ware sinks, wash basins, etc.with long screwed shanks and fly-nuts, flange endbedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repair Vitreous china squatting pan 'Orrisa' patterns of size 580mm x 440mm white, (excluding flushing cisterns and flush pipe), including brass chromium plated trap 'P' or 'S' pattern with inlet and outlet integral foot rests, complete all as specified

S&F in repair PVC valveless double syphonic action type flushing cistern low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet including brackets & connection to pipe etc complete all as specified and as directed

S&F in repair of Vitreous china WHB 550x400mm size white flat back with brackets incl cutting or pinning ends of brackets (including waste pipe) incl Waste coupling of PTMT (32 mm dia) (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gm complete all as specified and directed.

S&F as in repair 15mm bore Pillar taps fancy type, with long swan neck , chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and as directed

S&F in repair 15 mm Stop valves/ angle valve fancy type cast copper alloy with chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed.complete all as specified and as directed

S&F in repair 15 mm Stop valves (concealed type long shanks) fancy type cast copper alloy with chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed.complete all as specified and as directed

S&F in repair bib tap fancy type cast copper alloy chromium plated screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed.

Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 15 mm dia bore complete all specified .

Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 20 mm dia bore complete all specified .

Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 25 mm dia bore complete all specified .

S&F 20mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, including taking down complete all as specified and as directed.

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 25 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F laying of CPVC pipes SDR 11& plain CPVC SDR 11 20mm outer dia laid in trenches/wall complete all as specifed

M&L Cutting chases,pinning making good to facing where required and pointing in CM 1:3 for concealled water tubing etc and making good cutting n.exc 10cm girth complete all as specified and as directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm etc. complete all as specified and as directed

S&F 0.5mm thick stainless steel plate rack of overall size 24x 36 x 10 inch of standard quality and shapes completed all specified and as directed.

Supply and fix as 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete as specified.

S& F in repairs CP Soap dish of any type fixed to plugs with chromium plated brass screws complete as specified.

Taking down PVC drain pipes ( any size or pattern) including all fittings head shoes etc complete all as specified and as directed

S&F 110mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed

S&F 110mm bore PVC (SWR) `P' or 'S' trape complete all as specified and directed

S&F 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F PVC (SWR) floor trap, plain with grating 75mm including jointing to wast pipe fixed in cement concrete type B1 (1:2:4) ,in repairs and including waterleak proof treatment complete all as spcified

Taking down existing unserviciable water proofing treatment from roof slab and cleaning the roof slab by wire brush and removing WPT felt beyond the MOD premises etc complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15mm thick in CM (1:4) on roof slab concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

Application of waterproofing Coating : Providing and applying Fostoc Brushbond Roof Guard, a single component High build fibre Reinforced Acrylic Waterproofing render for roofing system to be applied by brush, at three coats at minimum dry film thickness of 1 mm, which should cure by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane. Solid Content - 70%, Tensile strength ASTM D 412-1.10 Mpa, Elongation ASTM D12-100%, Resistance to ageing due to - 1000hours, UV radiation ASTM D4587 E - No Change, Rapid Chloride Penetration ASTM c 1202 - Very low, Pull off adhesion ASTM D541 - 0.92 Mpa, Resistance to Algae growth ASTM D 5589-97 - Passes, Zero rating, Permeability (mm) (BSEN 12390 part 8) -n 5.0, Water vapour transmission (ASTM E 96) - 6.0g/m2

Excavation in trenches n exc 1.5 m deep and n exc 1.5 m width and getting out in soft/loose soil all as directed by Engineer - in - Charge

Returning filling in including spreading watering well ramming in layers n exc 25 cm thick all as directed

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.50 m above the starting point..

M&L for Precast RCC 1:2:4 type B1 (20mm graded stone aggregate) as in manhole cover including necessary form work set in cement mortar 1:4 all as specified and as directed

M & L for Plain cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate as in concrete bed including packing under & haunching against sides of bore pipes after the pipe are laid and tested for 150mm complete all as specified and directed by Engineer-in-Charge.

M&L for SGSW pipes 150 mm dia grade 'A' laid in trenches and jointed complete all as specified

M&L for Cutting salt-glazed stoneware drain pipe in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar l:l etc complete all as specified and as directed..

S&F gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and directed.

S&F hard drawn steel wire fabric (weight not exc.4kg/Sqm) fixed in tank caging, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, complete all as specified and directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, complete all as specified and as directed.

S&F chromium plated 2 in 1 long body bib taps including joints to steel pipes or unions and plugging and screwing complete all as specified and as directed

S&F hand shower (Health Faucet) ABS Body with 8 mm dia, 1.25 mtr long flexible tube & wall hook etc complete all as specified and as specifed and as directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

S&F 110 mm bore PVC (SWR) access door bends any radius complete all as specified and directed

S&F 75 mm bore PVC (SWR) access door bends any radius complete all as specified and directed

M & l for Making good under cills over arches, lintel and bresummers,including all pinning when nessesary with using cement mortar 1:6 complete all as specified

M & L for Removing & Hacking of existing concrete Carefully by low impact high frequency hammer OR by manual chipping without damaging the existing concrete or control sand blasting including cleaning the surfaces by air jet etc. complete. (Mode of measurement - per sqmt of breaking area of concrete) complete all as specified and directed

M & L For reebaklens RR with brush for complete wetting of rusted metal iron base surface and allowed to react it for 16-24 hours. Note Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth. complete all as specified and directed

Providing and applying two coats of Nitozinc Primer a two component epoxy zinc rich primer or equilvalent product on the properly cleaned and prepared steel bars after the required chipping and cleaning of the concrete surface as per the manufactures specification. complete all as specified and directed

Providing and applying structural grade long pot life epoxy bond coat of Nitobond EP Std prior to building up of section with any type of mortar / concrete to ensure bond between old concrete and new concrete by brush application as per the mgf specifications. complete all as specified and directed

Supply and apply concrete surface with single component, fibre reinforced shrinkage compensated, polymer modified structural grade repair mortar like Fosroc Renderoc SP 40 or equivalent at a thickness of 40mm. The repair mortar should have a compressive strength 45 N/mm2, flexture strength 7 N/mm2 and tensile strength 2.5 N/mm2 at 28 days. complete all as specified and directed

Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking dwn old/unsv distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/Main Switch including old Unsv MCCBs/MCBs, isloators , etc and making good to disturbed surface complete all as specified and as directed.

M&L for point wiring for one light point/ one fan point/ one exhaust fan controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made anodized pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes suitable size and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM (1:3) to for One light /Fan point controlled by one, one way switch match with the adjoining surfaces , complete all as specified and as directed.

All as per item No 134 here-in-before but for one light point controlled by two , two way switch 5 Amp on the same board complete all as specified and as directed.

All as per item No 134 here-in-before but for one 3pin 5 Amp switch socket outlet, independent board , complete all as specified and as directed.

All as per item No 134 here-in-before but for one fan point/exhaust fan point controlled by one way switch 5amp on the same board complete all as specified and as directed.

All as per item No 134 here-in-before but for one 3pin 5 Amp switch socket outlet,same board complete all as specified and as directed.

All as per item No 134 here-in-before but for one 5/15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

S & for metal clad box suitable for 230 volt 50 HzAC supply three pin with MCB SP 20/32 Amps including removal of old unsv one complete all as specified and as directed.

Supply and fixing switch piano type, single pole, 5 amps, complete all as specified and as directed.

Supply and fixing switch piano type, two pole, 5 amps, complete all as specified and as directed.

Supply and fixing switch piano type, single pole, 15 amps, complete all as specified and as directed.

Supply and fixing switch socket , 2 in 1, 5pin, 5 Amp, complete all as specified and as directed.

S&F switch socket outlet, 2 in 1,6pin, 5 and 15 amp, complete all as specified and as directed.

S&F ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

S&F electronic fan regulator, flush type (Delux model), rotary step type, 5 step, not less than 100 watt, complete all as specified and directed.

S&F call bell ding dong, 230V single pole, complete all as specified and directed.

S&F Bell push, AC, 230volts, single pole, complete all as specified and as directed.

S&F MCB, SPN, DB, 8 ways, double door, Metal door, IP-43 IK 09 in 100A protection, isolated neutral bar, insulated busbar assembly complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S & F for sheet metal enclousre MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall , complete all as specified and directed.

S & F for MCB Three pole and neutral rated capacity 40 to 63 amp rating 415V, breaking capacity 10KA 'C' curve and current indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

S & F MCB single pole and neutral rated capacity 32 to 40 amp rating 240V, breaking capacity 10KA 'C' curve and current indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

S & F in replacment MCB single pole rated capacity 5 to 32 amp rating 240V, breaking capacity 10KA 'C' curve and current indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

S & F Decorative wall light fixture, brushed nickel finish, suitable for 9 W LED lamp (B22) including 9/10 W LED Bulb etc, complete with all accessories internally pre-wired and including connecting up with twin core twisted fiexible copper conductor cable suitable size, complete all as specified and directed.

Supply and fixing LED tube light batten type made of CRCA sheet with decirative end caps suitable with ultra bright glass LED tube light 1x18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/celling incl fittings accessories and connecting up with twin core fexible copper conductor cable suitable size all as specified.

S & F energy saving new generator enviromental friendly long life versatile presure die cast aluminium IP 66 for securty ligh fitting luninaire with high power LEDs as light source (100 Im/watt) with LDR sensor for automatic ON/OFF operation and electronic driver of capacity 25 watts with pre-wared and necessary mounting arrangements and provison of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade braket 1.5 mtr long bend to requred shape with clamps, nut bolts including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer , complete all as directed by Engineer-in-charge.

Taking down ceiling fan/exhaust fan any sweep, keeping with safe custody and return to GE Bengdubi store yard complete all as specified and directed by the Engineer-in-charge.

S&F BLDC ceiling fan 1200mm sweep 230 Volts 50Hz 5 star BEE rated with brushless direct current motor (BLDC) energy saving, 100% Copper wound motor with ani corrosive aluminium blades and other accessoried with service value 6.00, BIS certified and on site 5 years of warranty, wattage range 26-32 watts, Min air delivery 220 CFM at various location of GE Bengdubi area, complete all as specified and as directed.

S&F energy saving BLDC ceiling fan; 5 star rating, Type of motor - Brush Less DC Motor (BLDC) and Input Power - 32 to 35 Watts with full speed and reduced power consumption with reduced speed technology, Voltage- 90-300V AC, 50Hz, single phase, RPM - 340 to 375 rpm, Blades- Decorated, Sweep - 1200 mm, Air delivery - Not less than 210 CFM with service value 6.00 BEE and Colour - Glow white/ Toast Brown/ Gloss Black or others as approved by GE, complete all as specified and as directed.

S & F for energy Exhaust fan of 250 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaut fan is deemed to be included in overall rate quoted). complete all as directed and specified.

S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing , high transmissitivity diffuser , high lumen output box type fitting , 230 volts and intregated electronic driver connector block etc , complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193from ceiling rose to fitting complete all as specified and as directed.

Taking down geyser of any capacity, keeping with custody and refing the same complete all as specified and as directed.

S & installation and testing of Electric water heater , storage vertival type BEE 4/5 star rated, 25ltr capacity 240 volts 50 Hz comprising of high wattage heating element for instant heating , extre Mild steel with glass lined coated inner tank , rust & shock proof ABS outer body, non-ferrous pressure plate with & including provn of 4 Nos grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated , sheathed, stranded copper conductor cable/flexible chord and one no 15 amps 3 pin plug top etc complete all as specified and directed.

S & F in replacement light fitting .1x10W LED bulk head luminaries IP65, Min -50,000 burning hrs ,Diffuser made of high grade polycarbonate , high pressure die cast aluminium housing ,CCT-5700K,240 volt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50HZ complete all as specified and as directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 4.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 4.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, including taking down existing sub main wiring complete all as specified and as directed. Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 6.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 6.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, including taking down existing sub main wiring complete all as specified and as directed. Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (Medium grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, including dismantling old unsv ones complete all as specified . Note: GI earth wire 4sqmm dia and 15mm bore protection pipe upto 7.5m from earth plate is deemed to be included in the rate quoted be contrator.

M/S B D ENTERPRISE (BID ID -3513062)

KAMALA INDUSTRIES (BID ID -3513070)

M/S JANATA CONSTRUCTION (BID ID -3512660)

S.N. GHOSH AND CO. (BID ID -3512614)

CHAKRABORTY AND SONS (BID ID -3512592)

NEO BUILDERS (BID ID -3512833)