REPAIR TO FLOORING PLUMBING ROOF SHEET CEILING BRICKWORK PLASTERING JOINERY INTERNAL WATER SUPPLY SANATRY FITTING PERIODICAL SERVICES TO CERTAIN OTM ACCN (TY) AT RASPUNJA MIL CAMP UNDER GE (CENTRAL) KOLKATA

Amount

Demolition of cement concrete (Un-reinforced) in ground floor and paving nexc 15cm thick above or below GL complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as directed and directed.

Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed.

Dismantling of Wall and Ceiling Board (Fibre, Pulp, Insulation etc.) or Insulation Board/Slab /Blankets, any thickness including Cover Fillets, complete all as specified and as directed.

Dismantling Timber Scantlings, 40 Sqcm and over in Section, in any Position, in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlings, etc., under 40 Sqcm in Section, in any Position, as in Unframed Work, complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes nexc 1.5 Sqm complete all as specified and directed.

Taking down Chowkat or Frame with shutters (without taking off Shutter from the Frame) exc. 1.50 Sqm but not exc. 4.00 Sqm Each, complete all as specified and as directed.

Taking down of shutters of any description nexc 1.0 Sqm each and keep in Safe Custody for removing to store,complete all as specified and directed.

Taking down Shutters of any description, exc. 1.00 Sqm but not exc 2.00 Sqm Each and keep in Safe Custody for removing to store, complete all as specified and as directed.

Dismantling AC Corrugated Sheets as in Roofing including Ridge or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting any gauge, thickness, including nainital or similar roof coverings/sunshade, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work, viz. MS Flat Iron (Wind Tie) and Similar Work including MS Bolts, Nuts, etc., complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in mortar complete all as specified and directed.

Dismantaling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Hacking out old broken glass any thickness size quality or description from metal frame including punching or drilling out old glazing pins/springs clips complete all as specified.

Taking down unserviceable PVC (SWR) Pipes & Fittings of any size or pattern and in any Position (Measured overall as fixed along the Centre Line over the Fittings and Accessories), complete all as specified and as directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, or removing to store, complete all as specified and as directed.

Taking up or down Steel Water Tubing 20mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removing to store, complete all as specified and as directed.

M&L RCC (Nominal Mix) 1:2:4 type B-1 (Using 20mm graded stone aggreagate) as in slab, shelves supported on walls beam & coloumns in floor roof including balconies, conopies, deck slabs & shelves complete all as specified and directed.

M&L Plain Cement Concrete type C-1, (1:3:6) (40mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

Cutting chase, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe etc. and making good cutting not exc 10Cm girth.

M&L fly ash bricks pulverizes using class 'A 'old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

M&L half brick thick brick work with fly ash bricks pulverizes straigth or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and directed.

M&L Second Class Hardwood in Scantlings Clean swan Timber unframed and fixed complete all as specified and as directed.

Fixing only Second Class Hardwood in Scantlings wrought Timber Framed work and fixed complete all as specified and as directed. Note-Existing Timber shall be reused, obtain from dismantling item here-in-before.

M&L Second Class Hardwood plain fillets, sqaure, rectangular or triangular in section wrought, fixed with Nails, cross sectional area exc 13.0 Sqcm but not exc 25.0 Sqcm, complete all as specified and as directed.

M&L Second Class Hardwood Fillets wrought bull nosed splayed chamfered or round on one edge ,sqaure, rectangular or triangular in section Clean swan, fixed with screws, cross sectional area exc 6.0 Sqcm but not exc. 13.0 Sqcm, complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs,floor,slabs,landings and similar work not exceeding 200mm thick rough finished surfaces without using extra cement(Horizontal or slooping ) complete all as specified and as directed.

S&F Second Class Hardwood Plain, Solid, Straight Chowkats and Frames, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints, complete all as specified and as directed.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed.

S&F for 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed.

All as per item no 33.00 above but 30 mm thick divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers of shutter as specified in SSR Part-I 2009 complete all as specified and directed.complete all as specified and directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed.

S&F for Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

S&F 100mm Butt hinges, extruded brass, with brass hinge pin, bright polished, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section 200mm long complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy of 300mm long complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised 150mm long complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, 150mm long complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to fe 410-S.complete all as specified and as directed.

S&F Rolled mild steel in joist, channel, angle, or tee section fixed independently, without connecting plates, etc (cut to ordinary length ie. within 20mm of the length indicated) of FE-410- W(Gde-E-250) quality-B complete all as specified and as directed.

M&L Mild Steel Flat Iron 25 x 3 mm, as in Holdfast for Door, Window Frames or Chowkats etc., cut to length or drilled hole and fixed with Screw, etc., grade of Steel conforming to Fe-290 Gde E-165, complete all as specified and as directed.

S&F Steel window with side hung shutter including projection type hinges with steel handles, and steel peg stay with glazing bars dovetailed or welded incl taking out old window complete all as specified.

Material & labour of 1.50mm thick power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc.Complete all as specified and as directed. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass for window & wire mesh shall be measure and paid separately under relevant items of BOQ .

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed.

S&F Plain, galvanised, mild steel sheeting, class-3 thickness0.63mm in ridges,hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with "J" &"L" type hooks complete all as specified and as directed.

S&F Asbestos Cement Corrugated Semi-Corrugated Sheets 6.0mm thick as in Roof Covering fixed with L–type or J–type Cranked Hook Bolts with Washers, etc. and fixed, complete all as specified and as directed.

Fixing only old serviceable Asbestos Cement Corrugated,Semi-Corrugated Sheets 6.0mm thickheets obtained from dismantling item as in Roof Covering fixed with L–type or J–type Cranked Hook Bolts with Washers, etc. and fixed, complete all as specified and as directed.

S&F Asbestos cement two piece adjustable plain wing ridge 6mm thick for corrugated sheet fixed with "J" &"L" type hooks complete all as specified and as directed.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/files with aluminium anodised main 'T' section 35mm x 23mm x 1.50mm cross tee 35mm x 23mm x 1.50mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

M&L Asbestos Cement, Plain Building Board 4.0 mm thick, fixed with nails as in Ceiling, complete all as specified and as directed.

S&F 40mm bore MS tubing medium grade and fixed at wall for ceiling complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as item No.58.00 here in before but in skirting with and including 10mm thick rendering on fair faces of brickwork in CM 1:4 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Glazed ceramic coloured tiles 200x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L Glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L Granite slab 15 to 20mm thick of any type work table rubbed and polished in kitchen platforms and like over and including cement screed bed 15mm thick in CM (1:6) bedded and jointed with grey cement slurry and pointed with white cement mortor (1:2) using marble dust with admixture to match with shade of granite complete all as specified and directed.

M&L Rendering 20mm thick in Cement Mortar on fair faces of brick work or concrete surface of wall in two layer, first layer 10 mm thick in cement morter (1:4) and top layer 10mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. (NOTE:-WPC shall be measured and paid separately)

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

M&L One coat of white wash to old plastered surfaces of wall including preparation surface, complete all as specified & directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 2mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L complete removal of old decorated surfaces and Finishing walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L preparing old decorated surfaces and applying one coat of oil bound distemper complete all as specified and directed.

M&L preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: Old work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing old decorated plastered surfaces of Walls and applying One Coats of Exterior Emulsion Paint Weather Coat (any colour /tint) (as per Manufacturer’s instructions), complete all as specified and as directed. Make- Asian (apex ultima), Berger Paints-Weathercoat Lifelong7 ,Dulux Paints-Wheathershield Ultraclean

M&L preparing previously untreated surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each includ-ing Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L preparing previously untreated surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing new Wood and Wood Based Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

M&L Preparing surfaces of wood and wood based materials,new or old, of any description and girth, not otherwise described and treated with two coat creosote oiling complete all as specified and as directed.

M&L for preparation of old surfaces of wood or wood based materials of any descriptionand applying one coat of synthetic enamel paint (First quality) over 10 Cm width or girth complete all as specified.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

M&L for preparation of old surfaces of steel or steel based materials of any descriptionand applying one coat of synthetic enamel paint (First quality) over 10 Cm width or girth complete all as specified.

S&F Tinted glass with sheet glass 4.80mm thick , pin head type and glazing in squares exc 0.5 sq. M in each pane complete all as specified and as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square nexc 0.5 Sqm each pane complete all as specified and directed.

S&F 4mm thick frosted glass panes and glazing with oil putty in square nexc 0.5 Sqm each pane complete all as specified and directed.

S&F for 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F for 25mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" double socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any type, and Jointing with Solvent Cement as in repair complete all as specified and as directed.

S&F PVC (SWR) junction single (single T) equal or unequal 110mm bore and Jointing with Solvent Cement as in repair complete all as specified and as directed.

S&F Chromium plated Bib taps for 15 mm bore pipe as in repair complete all as specified and directed. Make : Essco (TQT-CHR-511) or equivalent make specified in the particular specification.

S&F Brass chromium plated long body bib cock with Wall Flange for 15 mm bore pipe as in repair complete all as specified and directed. Make : Essco (TQT-CHR-512) or equivalent make specified in the particular specification

S&F Brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe as in repair complete all as specified and directed. Make : Essco (TQT-CHR-512AN) or equivalent make specified in the particular specification

S&F Brass chromium plated Pillar Tap screwed for 15 mm bore pipe as in repair complete all as specified and directed. Make : Essco (TQT-CHR-508) or equivalent make specified in the particular specification

S&F ABS body chrome plated shower rose 125mm size including fixing to steel pipe or union complete all as specified and directe as in repair complete all as specified and directed. Make : Essco (EOS-542A) or equivalent make specified in the particular specification

S&F Shower arm 240mm long round shape with flage including fixing to steel pipe or union as in repair complete all as specified and directed. Make : Essco (ALE-536A) or equivalent make specified in the particular specification

S&F 15mm bore brass chromium plated Angular Valve with Wall Flange as in repair complete all as specified and directed. Make : Essco (TQT-CHR-526N) or equivalent make specified in the particular specification

S&F 15mm bore brass chromium plated 2 Way Angular Valve with Wall Flange as in repair complete all as specified and directed. Make : Essco (TQT-CHR-526AF) or equivalent make specified in the particular specification

S&F Chromium plated Health faucet with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer) as in repair complete all as specified and directed. Make:- Essco (ALE-CHR-583) or equivalent make specified in the particular specification

S&F Plastic water closet seat, in any coloure as directed closed pattern with flat/recessed bottom, and cover and mild steel chromium plated or aluminised hinging device for pedestal pan as in repair complete all as specified and directed. Make - Prayag (Cat No. 721) or equivalent make specified in the particular specification

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat botton cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old one complete all as specified and as directed. Make - Parryware Model No-C0297 Hindware(20011-SW), Essco (ECS-WHT-551PSPP)or equivalent model as specified in Particular Specification here in after.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting and 15mm dia PVC connector pipe, a pair of Cast Iron Brackets duly painted Stand including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down old one complete all as specified and as directed. Make - Parryware Model No-C0406(SP)/C0434(CTH) ,Hindware(10100-sw) Essco (ECS-WHT-801)or equivalent make as specified in the particular specfication.

S&F Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan excluding Flushing Cistern and Flush Pipe, fixing with and including provision of cement Concrete Bedding including taking down old one complete all as specified and as directed. Make - Hindwire cat No -20143, Escco (ECS-WHT-451) or equvilant of approved make specified in particular specification.

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed to WC including taking down old one complete all as specified and as directed. Make : Parryware Model No- E-8090, Cera cat part No CONGO B1010109 ,Hindware(510648-SW), Essco (ECS-WHT-201C)or equivalent model as specified in Particular Specification here in after.

S&F PVC Conncetions 15mm size with PTMT Nuts of length 450mm as in repair complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 500 Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nipples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F PTMT Ball Valve 15mm dia having mini -mum weight 142 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed as in repair, complete all as specified and as directed. Make : Prayag, Cat No 151 or equivalent make specified in the particular specification

S&F PTMT Ball Valve 20mm dia having mini -mum weight 210 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed as in repair, complete all as specified and as directed. Make : Prayag, Cat No 152 or equivalent make specified in the particular specification

S&F PTMT Ball Valve 25mm dia having mini -mum weight 455 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed as in repair complete all as specified and as directed. Make : Prayag, Cat No 153 or equivalent make specified in the particular specification

NIRMAL DAS AND CO.

K.P Construction Co

BHASKAR SUPPLY AGENCY