Tender for the Interior or Renovation work of NMC Office space at 7th Floor, Core-6, Scope Complex, New Delhi 03

BILL OF QUANTITIES (BOQ) for the Proposed Office Space for NMC,Scope Complex, New Delhi,

S.No. Sub-Head Amount (in Rs.)

1 HVAC WORKS 12,81,504.00

2 ELECTRICAL WORKS 65,69,350.00

3 PLUMBING & FIREFIGHTING WORKS 5,52,697.00

4 CIVIL & INTERIOR WORKS 54,36,717.00

5 FURNITURE 47,78,299.00

GRAND TOTAL i/c GST 1,86,18,567.00

GRAND TOTAL i/c GST 1,86,18,567.00

Digitally signed by ASHWANI

ASHWANI KUMAR BANSWAL

Summary of Civil and Interior Works

S.No. Description of Works Amount

Amount (SR, in Rs.)

2 Masonry & Plaster

3 Paving & Wet Works

4 Partitions & Wall Cladding

7 Finishes & Miscellaneous

GRAND TOTAL (Carried

GRAND TOTAL (Carried

INTERIOR FIT-OUTS for Office Space for NMC, Scope Complex, New Delhi

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

CIVIL & INTERIOR WORKS

TOTAL OF DISMANTLING - 0.00

2 MASONRY AND PLASTER

11.3 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat

cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 392.00 545.00 2,13,640.00

6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth

level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) SQM 56.00 1018.05 57,010.80

2.3 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. SQM 56.00 86.45 4,841.20

13.2.1 CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick wall of mix.

2.5 13.4 12 mm cement plaster of mix

5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas,

lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering,

finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

2.7 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

2.8 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 6.00 608.35 3,650.10

5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above

5.22A.4 Hot rolled deformed bars kg 150.00 89.65 13,447.50

MR POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick POP Punning over cement plaster in line &

plumb finished smooth to receive paint. (Internal surfaces of walls). 20.00

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with

water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg /sqm mixed with water

proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement

2.11 @ 0.242 kg/ sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours

followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners,

junctions of pipes and masonry with polymer mixed slurry.

2.12 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 220.00 200.90 44,198.00

2.35 ANTI- TERMITE - Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of

chemical emulsion) :

2.35.2 Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling

and plugging holes etc.:

2.35.2.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration sqm 392.00 44.70 17,522.40

MR FOAM CONCRETE FILLING UNDER TOILETS AND PNTRY:- Filling and compacting Foam Concrete for raising level of toilets and

2.14 pantry and finishing in a coat of lean concrete screeding with waterproofing compound complete in all respects to take Tile 5,333.79 7,200.61

Flooring as per flooring specifications. CUM 1.35

SUB TOTAL OF MASONRY AND PLASTER 3,99,391.02 13,502.82

3 PAVING AND WET WORKS

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

8.31 TILE DADO :- Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by

3.1 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)

and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less

than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1

cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and

matching pigments etc., complete.

11.40 CERAMIC TILE FLOORING :- Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be

specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White,

3.4 Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry 5,267.93

@ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

11.46 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than

0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of

cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with

white cement & matching pigments etc. complete.

11.48 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired

3.6 shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of

Engineer-in-charge.

MR KITCHEN/ PANTRY/ HAND WASH COUNTER :- Providing and fixing pantry and toilets with Granite stone top (with straight edge

polished nosing) complete with base cabinet made of 20mm BWP board, outside surface (shutters) finished in 1mm thick

Laminate of approved shade. All internal surfaces to have balancing laminate. The rate inclusive of necessary hardware, handle

lock sets, self closing hinges, spring loaded shutter, latch inside, all cabinet hardware complete as per Architects approval. (BR of

stone to be taken as Rs 1600/Sqmt). Width of work top counter 600mm/ detailed drawings.

MR Providing and Fixing of floor tiles with wear layer is of 0.5mm, made upof Stone Polymer composite, 100% Water & Termite proof,

Scratch/ Flame/ UV resistant, anti-microbial, 100% recyclable Green product having click system with suitable skirting.

Classification of abrasion resistance (Abrasion wheelfromH-18 Calibrade, loadApplied 1000 grams, No. of Cycles 14,400). " (

Along with Matching Profiles) SQM 115.00

TOTAL FOR PAVING & WET WORKS 6,59,670.33 4,00,970.09

4 PARTITIONS AND WALL CLADDING

9.105 GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm

thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm

length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and

other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610

mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with

suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both

side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width

(0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using

metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing

tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per

manufacture's specification and direction of engineer in charge all complete.

9.105.1 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board

conforming to IS: 2095: SQM 5.00 1797.65 8,988.25

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

9.133 Gypsum Panelling:-Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness

fixed on the ‘W’ profile (0.55 mm thick ) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm,

placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55

mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with

fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head screws @ 200

mm C/C., all complete as per the drawing & directions of engineer-incharge, the joints of the boards are finished with specially

formulated jointing compound and 48 mm wide jointing tape to provide seamless finish.

9.133.3 Gypsum board conforming to IS: 2095 Part - I

MR GLASS PARTITIONING:- Providing & Fixing Full Height Glass partition using 12mm Thk. Glass with anodised Aluminium frame fixing

glass with snap on option consisting of top, bottom and side frame measuring 40-46mm x 18mm-25mm complete with glazing

rubber as per manufacturer's specifications and instructions of Engineer- in-charge. Rate include supply & Installation of 12 mm

thk toughened glass with double sided adhesive tapes for glass to glass butt joints. Partition system from FFL to False Ceiling level,

inclusive of cost of support required for fixing in the ceiling. The frame to be powder coated in desired shade as per the

instructions of the Architect. SQM 59.00

MR PLYWOOD PARTITIONING- Plywood partition using 12mm fire retardant ply fixed on both sides on aluminium Studs Frame

4.4 50mm x 50mm x 0.5mm & 50mm x 60mm x 0.5mm as per approved sample and architectural drawings placing the same 3,461.47 4,84,605.39

600mm c/c . Aluminuim frame to be fixed to floor and RCC Ceiling using fastners. SQM 140.00

MR PLYWOOD PANELLING- Plywood panelling using 12mm fire retardant Ply fixed on one side on Aluminium Frame 50mm x 25mm as

4.5 per approved sample and architectural drawings. Aluminium frame to be fixed to walls, floor and RCC Ceiling using fastners. 2,248.82 5,23,974.56

MR VEENER CLADDING- Providing and Fixing 4.0 mm thick decorative /Natural Veneer of approved design and shade , cladded on

4.6 to existing partitioning. Complete Cladding to be finished using mellamine polish (gloss/matt) as approved by the architect. 2,746.70 2,06,002.42

4.7 MR LAMINATE CLADDING- P/F 1.5 mm thick laminate including 4 mm thick MDF, on an existing Plywood surface. 1,585.94 5,07,500.09

12.62 INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48

4.8 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in

position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge. SQM 140.00 277.90 38,906.00

9.18 SHELVES:- Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board

IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked,

in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid

based on Cabinet Carcass- Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood

9.18.2 particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS :

12823 marked, in cabinet carcass with screws and fittings wherever required, edges to be painted with polyurethane primer

(fittings to be paid separately). SQM 40.00 1501.00 60,040.00

MR Providing & fixing IInd class teak wood lipping 25 mm wide x 12 mm thick complete with all necessary nails, hardware etc.

9.79 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers

of approved quality including necessary screws etc. complete.

4.13 9.81 Providing and fixing bright finished brass handles with screws etc. complete:

9.129 SHUTTERS:- Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or

graded wood particle board IS:12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other

4.14 side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright

finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge

MR STORAGE CABINET FOR ELECTRICAL PANEL AND VOLTAGE STABLIZERS- Cabinet Shutters out of 19mm Commercial Plybaord

finished in 1mm Laminate of base cost Rs. 380 per sqmt. Shutters to be fixed to a frame. Rigidly fixed on both sides and top

4.15 finshed in laminate. No internal carcass required. All Hinges of hettich or equivalent. Internal Surface of the shutter in balancing 8,703.25 34,813.00

white laminate. All shutters to be provided with Stainless steel louvers at the top and bottom of the shutter as per the site

requirements and instrcution of the Engineer In charge. SQM 4.00

SUB TOTAL OF PARTITIONS AND WALL CLADDING 3,85,036.69 19,67,328.74

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

12.45 GYPBOARD CEILING :- Providing and fixing false ceiling at all height including providing and fixing of frame work made of special

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre,

one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the

angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with

5.1 intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5

mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall

be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

Including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound

, jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer

suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction

of the Engineer in Charge but excluding the cost of painting with :

a) 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I SQM 250.00 1145.95 2,86,487.50

5.2 MR Providing and fixing of mineral fiber ceiling tiles, with hot dipped galvanized steel grid work (Silhotte) , surface chemically

cleaned capping pre-finished in baked polyester paint, Main Tees of size 38 (H) x 15 mm every 1.2M centre to centre, centre to

centre to form a grid of size 600 X 600 mm and suspending the grid from RCC roof using 3 mm GI rod, 6 mm nylon rawl plug and

6mm J bolt at every 1200 mm intervals. And laying mineral fiber Acoustic ceiling tiles MV B-Pin of size 600 x 600 x 15 OCR mm over

the formed grid having fire rating of 60 minutes as per BS 47G / 23 of 1987. Light Reflection of > 85%. Noise Reduction Coefficient

(NRC) of 0.70, Sound Attenuation of 32 db, K = 0.52-0.57 W/mk. Humidity Resistance up to 99% at 50’C. The grid to be used is

Silhoutte type as per approval of the architect

MR TRAP DOOR :- Providing and fixing trap door in false ceiling made of "Novapan "pre-laminated board with hardwood framing,

5.4 dead locks, lapping all around including all hardware, hinges etc. complete as per design and drawing. 2,913.67 11,654.66

MR CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwood framings hung from ceiling

5.5 @1000mm centre to centre with 1 nos of 12mm thk. fire retardant ply on vertical & 12mm thk. Commercial ply on horizontal 960.18 15,362.93

surface (straight & curved). Inclusive of finishing in Paint. RMT 16.00

MR Providing the gypsum double sided cove of 150mm x 150mm having a facia of 75mm to macth the specifications same as

above RMT 95.00

MR Providing the wooden cove of 150mm x 150mm having a facia of 75mm to macth the specifications same as above.

MR GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum ceiling. In order to make

5.9 the Mineral Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm as per drawings. (visible surface of gypsum 390.55 17,574.70

band to not exceed 100mm) including plastic emulsion paint. RMT 45.00

SUB TOTAL OF CEILING 2,86,487.50 3,93,750.36

6 DOORS/ WINDOWS

6.1 MR 35MM THICK LAMINATED FLUSH DOOR WITH FLOOR SPRING- 35mm thick flush Doors finished using 1mm Thick Highland Pine

Laminate on both sides panel of size upto 2400mm x 1050mm complete with Hardware including floor spring, Door Closer, dead

Lock with inbuilt key, D-Handle etc. including cost of teak lipping all around with melamine/ duco finish. The item to include

installation of all kinds of latches as per the requirement. Nos 9.00

9.1 DOOR FRAMES- Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and

6.2 fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood CUM 0.13 131576.95 17,105.00

9.21 FLUSH DOOR:- Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of

6.3 block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or

cross bands and face veneers on both faces of shutters :

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 2.40 2015.75 4,837.80

9.22 Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters

conforming to IS: 2202 (Part I)

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

9.22.1 On one side only SQM 2.40 408.05 979.32

9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all

area of door shutter to be measured) SQM 2.40 401.40 963.36

9.40 Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on

unexposed surface etc. complete:

9.40.1 2nd class teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and

6.6 9.53 embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm

nominal size). EACH 6.00 194.35 1,166.10

6.7 9.72 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete

DOOR CLOSERS:- Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having

6.8 9.84 brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm),

with double speed adjustment with necessary accessories and screws etc. complete. EACH 2.00 856.3 1,712.60

MR MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123 with Roses & Escutcheon in SS packaged

with Mortice lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all flush doors. EACH 2.00

6.10 9.81 HANDLES;- Providing and fixing bright finished brass handles with screws etc. complete:

9.97 TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic AC 10 as per IS : 1868 ), transparent or

dyed to required colour or shade, complete:

9.82 DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

MR FIRE DOOR- Providing and fixing single leaf 120min Rated Fire Door of size 900x2400. with vision panel using wired glass complete

with Fire proof door frame. One side to be finished in fire retardant paint and one side to be finished in Laminate of approved

shade. All Frame to be finished in fire retardant paint. All hinges and hardware to be thermatically sealed and 120 mins fire rated.

21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including

6.16 providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required

door fittings, all complete as per direction of Engineer- incharge. SQM 3.30 4540.70 14,984.31

MR UPVC Windows : Supply and Fixing of Tripple Track/ Tripple Channel Factory made UPVC Windows along with DGU/

Sandvich Glasses (6 mm Reflective Glass + 12 mm Air Gap + 6 mm Plain Toughned Glass) on two tracks and SS Mesh on One

Track inclding all required hardware i.e. handles, locks and other etc., complete as per the requirement of

engineer in charge. SQM 16.00

SUB TOTAL OF DOORS 46,760.45 4,10,233.24

7 FINISHES & MISCELLANEOUS

13.43.1 PRIMER: Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. Water

thinnable cement primer. SQM 250.00 64.45 16,112.50

13.48A ACRYLIC EMULSION PAINT: Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV

7.2 resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted)

with silicon additives.

13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90

10.25 Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 150.00 142.30 21,345.00

7.4 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

13.61.1 Two or more coats on new work SQM 300.00 131.45 39,435.00

MR Providing & fixing imported decorative Poly décor fabric Wall Paper (Object) of weight 475 g /sqm as per approved shade

& design including prepration of surface with 2 coats of Nubin Glue based epoxy quote. 25.00

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

M.R. ZEBRA BLINDS - 190g/sqm, thickness - 0.50 mm - 0.70mm ( opaue part ), Colorfastness to light - above 4 grade. Blind tube is made

of Aluminum with a diameter of 36mm, botom rail is made of Aluminumwith powder coated having weight 390 gm/meter fitted

with end caps in colour matching to thefabric and mechanism is of plastic with chain and metal bracket. The Blinds comes with

Aluminum cover with the matching fabric designed on it. Aluminium profile should have temper WP consisting of alloy 63400

along with anodizing of 10 micron and powder coating of 60 micron. The tensile strenghth of profile should be 9.10 Kg/mm

square and elongation 18.The control clutch driveunit engineered heavy duty chain drive pulley operating system consisting of

gear clutch housing and locking plug containing minimum 6 ribs and inserted at minimum of 38mm into roller tube. It is self-

lubricating Exclusive clutch with safety pins for secure bracket installation and unlocking pin for quick manual removal. Universal

7.6 clutch is most convenient for large windows down to the smallest windows. It shall be driven by a ball chain pulley with ball 3,338.68 1,30,208.60

chain and can be positioned at Right hand or Left hand side of the shade. Clutch gear ratio of 1.75:1 for reduced operating

force on larger blinds.. Mounting hardware brackets universal brackets including end plug bracket with lock down retainer

device.Brackets finish of powder coated metal installation brackets made of stamped and hardened steel. Roller tube circular-

shaped aluminium tube extruded from alloy 63400 and temper WP. Bottom rail flat-shaped extruded aluminium from alloy 63400

and temper WP. Ball chain shall be 2mm diameter cord with plastic balls moulded to form an endless ball chain. It is used for

raising or lowering action of the shades. Plastic parts all plastic components are UV-stable compounds available white.

M.R. FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface with 15 yrs MCS warranty as approval of the

Architect. (Only film surface area shall be measured and paid). 12.00

Providing and fixing of 4,6 mm thick annealed GRIHA rated lacquered glass manufactured industrially by curtain coating

process with PU lacquer (50 micron thick), opaque (if viewed against a support wall) conforming to EN 16477 standards for back

painted glass , of approved color by Architect/ Client fixed with compatible Silicone having Shear Bond Strength (Dry, 24 hours),

greater than 450 kpa and tack free time of 10 to 30 mins compatible for installation of mirror and lacquered glass / Foam based

double sided adhesive tape for instantaneous adhesion, compatible with mirror and lacquered glass having Shear bond strength

7.9 (Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board 3,532.63 17,663.13

which is mounted on the RCC wall/any other structure. The contractor should submit test reports for backpainted glass from

manufacturer - High humidity Resistance (conforms to BS EN 1036 1999); Color fastness ISO 105B02 standard & Mechanical

Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 ( Cross Hatch Test ) standard The manufactured backpainted glass should be

environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial /

6% post consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass

M.R. Providing & fixing 12mm Thick. 100% Acrylic solid surface of approved make and colour using approved Adhesive to 12 mm thk.

Waterproof Plywood of approved brand as per shape, pattern & details given in the drawing. The rate includes providing & fixing

beading, cutting, scaffolding, nails, all materials, labour, lead, lifts, HOM etc., complete.-for Lift Cladding. (The make, Shade,

pattern etc., to be approved by Architect). SQM 6.50

SUB TOTAL OF FINISHES 3,58,080.56

Furniture BOQ for Office Space for NMC, Scope Complex, New Delhi

SL Items Unit Qty Rate Amount

Providing & Installation of custom made cabin tables of following sizes made out of 19mm thk. Commercial Board finished in natural Teak finish veneer. All edges to

be finished in teak moulding as per design. The visible faces to be divided in equal parts as per design. Side Unit, Back unit, to be made with storage shutters finished

in natural Teak veneer. The non visible areas to be finished with 0.8mm thk. balancing laminate of approved shade. A Drawer pedestal with 3 drawers to be

provided under the table. All teak veneer surfaces to be finsihed in PU polish. Note: Side Unit & Back units to be provided as per design.

a MR Main table - 2400mm X 900mm X 750mm; side table upto - 1200mm X 450mm X 750mm; back storage - 2300mm X 450mm X 750mm Nos. 2.00 2,08,621.12 4,17,242.24

b MR Main table - 2100mm X 750mm X 750mm; side table - 950mm X 450mm X 750mm; back storage - 2900mm X 450mm X 750mm Nos. 1.00 2,05,000.00 2,05,000.00

c MR Main table - 2100mm X 750mm X 750mm; side table - 950mm X 450mm X 750mm; back storage - 1700mm X 450mm X 750mm Nos. 1.00 1,78,000.00 1,78,000.00

d MR Main table - 1800mm X 750mm X 750mm; side table - 950mm X 450mm X 750mm; back storage - 1700mm X 450mm X 2700mm Nos. 4.00 1,56,000.00 6,24,000.00

Providing & Installation of custom made veneer storages out of 19mm thk. Commercial Board finished in natural Teak finish veneer. All edges to be finished in teak

Veneer moulding as per design. The non visible areas to be finished with 0.8mm thk. balancing laminate of approved shade. The shutters to be provided as per design

storages (sliding of swing). All teak veneer surfaces to be finsihed in PU polish. The storage to be made complete as per approved drawing and satisfaction of engineer-in-

charge. (NOTE: Only the face area of the storage to be measured for payment.)

Providing & Installation of Custom made conference Room Table (3.0 m X 1.2m X 0.75m (h)) in 19mm thk. Commercial Board finished base and top. The top to be

Meeting Room finished in 12mm thick acrylic solid surface in approved sample. Legs of the table ot be hollow for taking the wires upto the table and a 19mm Thk Commercial

table board Raceway below table top to be provided for carriage of cables. The cost to include making of cut outs necessary for electricity pop up boxes. All teak

veneer surfaces to be finsihed in PU polish.

Providing & Installation of custom made Reception table of size upto 1.5m x 0.75m x 0.75m (ht) made out of 19mm thk. Commercial Board finished in veneer and

4 acrylic solid surface of approved shade as per design. The Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above Nos 1.00 95,000.00 95,000.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium

trims. Tiles: Combination of top tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing board/ clear glass tile/ plain metal/ prelam tile.

Bottom tiles - Plain metal/ fabric magnetic / fabric / laminated /prelam. The panel thickness comprises of 38mm (35 mm Minimum) thick paper honeycomb +

3mm MDF on each sides + 0.6mm decorative laminate or fabric on both sides. The uprights and horizontals shall be made of aluminium extrusion having average

wall thickness of 1.2 mm & powder coated with epoxy- polyester powder. Particle board framing is used on outer boundary of these blocks as well as

intermediately at certain locations forming conduit for passing cables. These blocks are located in the mid segment of the panels and can be provided with

cutouts for mounting switch boxes (above or below the worktops). Top tiles can be offered in variety of combinations. The fins along the depth shall be 22.8mm thick.

Worksurface- out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200mm x 600mm x 750H. Brackets shall be made from 2mm thick

CRCA steel. Pedestals with legs - Nova pedestal flat metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm height 3dr = 2box+1file. The

work shall be carried out as per the instructions and guidance received from engineer incharge. Providing and placing ALL WOOD HINGED DOOR UNIT

(HDU). Construction & Material Knockdown construction. Door Opening Twin door with self closing hinges of Wood made from18mm Thick Pre Laminated Board.

Handle · Aesthetically appealing recessed plastic handle for& wooden Doors. Locking Mechanism Cam lock · 3 point locking mechanism in Wood Door Shelving ·

Height wise Adjustable Shelf Mounting. Wooden Top shall be be made from Pre-Laminated Board of 25 mm thk. Skirting of 125 mm High shall be provided. Leveler

Screw type adjustable Leveler with plastic base. height. Back Panel and Sides of the storageunits will be made out from 18mm thick Pre-Laminated Particle Board.

Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 10mm of uneven flooring. The work shall be

carried out as per guidance and instructions received from engineer incharge.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using Quilted knitted fabric. Seat Size:-

47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an

up=Down adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an armrest top. It shall have Front pivot synchro

mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back

8 high back chair tilting ration of 1:2. The lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted Nos 9 20,655.08 1,85,895.73

through two projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment

stroke of 10cm. The pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black polypropylene hub cap. the work shall

be carried out as per guidance and instructions recieved from Engineer Incharge. This shall come along a headrest assembly consisting of polypropylene pad with lumbr support

and covered with polyester fabric. Neckrest assembly has an adjustment stroke of 4.2cm and otation adjustment stroke of 76 degrees.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & upholstered using Quilted knitted fabric. Seat Size:-

47cm(w) × 51.5cm (D). The HR polyurathene foam is moulded with density =45+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an

up=Down adjustment of 8.0 ± 0.5cm which is provided in armrest structure. Armrest structure is chrome plated and fitted with an armrest top. It shall have Front pivot synchro

mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension adjustment, 4 position locking with anti- shock feature, seat/back

9 mid back chair Nos 20 19,402.77 3,88,055.44

tilting ration of 1:2. The lumber support consists of polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be adjusted

through two projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm in height. The pneumatic height adjustment has an adjustment

stroke of 10cm. The pedestal is fabricated from 0.2cm thick HR sheet chrome plated and assembled with injection moulded moulded black polypropylene hub cap. the work shall

be carried out as per guidance and instructions recieved from Engineer Incharge.

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch

knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3.

The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a

simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact cushioning while seating and synchronises with

the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled

10 Polyamide form the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt limiter Nos 22.00 17,060.38 3,75,328.31

feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable armrests assembly consists of armrest housing sliding over the armrest

structure, both moulded in glass filled Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled

Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair shall be

76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat should be made of PU foam with Density

28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM:

The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with

11 3 seater sofa fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) Nos 3.00 53,900.16 1,61,700.47

and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for

cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. The seat should be made of PU foam with Density

28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM:

The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with

12 2 seater sofa fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) Nos 1.00 44,031.53 44,031.53

and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for

cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Vertical Filing Cabinets whcih use less floor space. Size of 4 Drawer VFC shall be 1320mm(H) X 470mm(W) X 620mm(D). All the components shall be made of CRCA . It

should have 1 Point Locking Mechanism and a Rigid Knock Down Construction. The Top, Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside

cover and Side Back Side thickness should be 0.6mm. The Back, Bottom and Drawer thickness should be 0.5mm. Easy to grip Full length Recess Handle shall be

integrated into Metal Drawer for easy pull out convenience. There shall be a Snap on type plastic label holder on Drawer Fronts. In addition, 28 ‘Ezee’ / ‘Visa’ files

(Foolscap) from front to back of thickness 20mm per drawer can be hanged in VFC. The Centralized locking System shall be provided along with Shooting Bolt

Mechanism and 10 Lever Cam Lock. The VFC should have anti-tipping arrangement which ensures that when one drawer is opened for use, it does not allow other

drawers to be opened. The High Quality Precision Ball Slide shall be provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangular

plate pop should be riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partition and Cradle for hanging A4 file folders front to back should

also be available. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).

STORAGE CABINET FOR GENERAL STORAGE- Out of 19mm Commecial Ply Board finished using 1mm thick laminate, complete with all hinges, drawer glides and

hardware from approved make. All internal surfaces to be completed using balancing white laminate. Including D-type handles for shutters and recessed type

handles for drawers. Storage to be of all heights as per design complete and instruction of engineer-in-charge. (NOTE: Only the face area of the storage to be

measured for payment.)

SUMMARY OF BOQ FOR ELECTRICAL WORKS FOR OFFICE FOR NMC SCOPE COMPLEX, NEW DELHI

S.NO. SUB HEAD NDSR AMOUNT (Rs.) DSR AMOUNT (Rs.)

1 MAIN PANEL Rs. 2,91,344 Rs. 38,083

2 CABELS / MAINS Rs. 2,54,994 Rs. 19,254

4 LIGHTING FIXTURES Rs. 3,35,972

5 WIRING FOR DATA AND VOICE OUTLETS Rs. 1,13,415 Rs. 3,46,069

6 CABLE TRAY.& RACE WAY. Rs. 3,34,707 Rs. 1,17,070

8 FIRE DETECTION & PA SYSTEM Rs. - Rs. 6,84,902

9 UPS & INVERTER SYSTEM Rs. 5,08,216 Rs. -

10 CCTV System Rs. 3,04,246

11 Access Control System Rs. 3,01,050

GRAND TOTAL Rs. 65,69,350

GRAND TOTAL Rs. 65,69,350

VASTU MANDAL arc hitec ts, interior d esig ners

F-328, Old MB Road . Lad o Sarai. Mehrauli, New Delhi 110030

Telfax 41665455 Email :vastumand al@g mail.c om

PROJECT - NMC SCOPE COMPLEX, NEW DELHI _ELECTRICAL WORKS ESTIMATED COST

S.No Description Unit Qty Rate MR Amount DSR Amount

MR Design, manufacture, supply, installation, testing and commissioning of following LT switch-

gear panels suitable for 415 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel

shall be, Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust

and vermin proof type compartmentalized design fabricated out of 14 SWG sheet steel,

complete with aluminium bus bars, separate earth bus bar to be provided through out the

length of the panel. The incoming and outgoing feeders shall be accommodated in a

modular multitier arrangement and shall be interlocked to avoid paralleling, adequate size

cable alley, painting, earthing, numbering, danger plate etc as required as per

specifications and drawings.

One (1) No. 250A, 35 KA, TPN MCCB.

b) Metering & Indication :

One (01) No. digital volt, current & Frequency (VAF) Meter with in built selector switch,

250A/5A CL-1.0,15VA CTs and control fuses.

One (01) set each of three (3) nos. phase indicating lamps with fuses.

Electrolytic high conductivity Aluminium three pole and neutral busbars rated at 300 amps

having a maximum current density of 1 amp per sq mm insulated with heat shrinkable PVC

sleeves as shown in single line diagram.

d) Outgoings :

One Nos 100A TPN MCCB 25 KA

Three (3) Nos. 40 A, 10 KA, TPN MCBs "C" curve type

Five (05) Nos. 32 A, 10 KA, TPN MCB "C" curve type

MCCB shall be provided with thermal magnetic protection releases for short circuit &

overload protection.

MCCB shall be (Ics=100% Icu) with 0.8 - 1 x In adjustable overload protection release.

MCCB shall be provided with spreader terminals, phase barriers and rotary handle operating

2 DISTRIBUTION BOARDS :

Supply ,Installation, Testing & commissioning of following double door type distribution boards

fabricated out of 16 SWG, CRCA sheet steel recessed in wall or surface mounted.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution

board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/Isolator)

2.3.1 6 way , Double door Each 1 1,661.00 1,661.00

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker

2.3 2.10 suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual

2.5 2.14 current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Total of Main Panel/ DB carried over to summary 2,91,343.95 38,083.00

3.0 CABELS / MAINS

8.4 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade

of following size in the existing masonry open duct as required.

b 8.4.2 Above 120 sq. mm and upto 400 sq. mm Meter 150 96.00 14,400.00

Supply of 1100V grade armoured cable having sector / circular shaped aluminium / copper

conductor PVC insulated cores under ground PVC tape wrapped inner sheathed, GI strip /

3.2 wire armoured and overall extruded PVC sheathed confirming to IS: 1554, laid on wall or

ceiling using GI clamps and spacers as per route shown at site and further as directed by

Engineer-in charge

a MR 185 Sq.mm 3 1/2 core Aluminium cable mtr. 150 1,699.96 2,54,993.52

9.1 Supplying and making end termination with brass compression gland and aluminium lugs for

3.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Total of Cables / Mains carried over to summary 2,54,993.52 19,254.00

Point wiring for light point /Fan/Exhaust Fan point/ call bell point using 2 runs of 1100 V grade

1.5 sqmm & one run of 1.5 sq.mm FRLS insulated multistranded copper wires, in & including

25 mm dia , MS conduit surface/ concealed in wall / ceiling conferming to IS 732 including

all accessries such as junction boxes , conduit bends, elbows and ceiling rose , and anodised

GI switch box with modular switch ,modular plate and the box covered with front plate

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without independent

switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed steel conduit,

and earthing the point with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

4.2 1.7 insulated copper conductor, single core cable in surface/ recessed steel conduit as

a 1.7.1 2x1.5sqmm+1x1.5sqmmearth wire 200 208.00 41,600.00

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Per

2 X 4 sq. mm + 1 X 4 sq. mm earth wire Per

4.3 1.3.3 Exhaust fan point including of ceiling rose near fan. - Primary - Group-C Per Pts 1 1,213.00 1,213.00

Wiring for twin control point wiring using 1.5 sqmm copper conductor FRLS PVC insulated

copper conductor cable drawn through 25 dia MS conduit laid in surface/concealed over

4.4 1.4 false ceiling or in slab/wall chases including ,2way modular switches,modular plate ,suitable Per Pts 45 1,290.00 58,050.00

GI box and earthing the point with 1.5 sqm FRLS PVC insulated copper conductor single core

cable as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 132 111.00 14,652.00

d 1.24.5 6 pin 15/16 A socket outlet Each 58 175.00 10,150.00

f 1.24.7 TV antenna socket outlet Each 8 119.00 952.00

Supplying and fixing following size/ modules, GI box along with modular base & cover plate

for modular switches in recess etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes

etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

4.8 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the Meter 200 33.00 6,600.00

existing surface/ recessed steel/ PVC conduit as required.

4.9 MR Supplying and laying HDMI Cable with connector on both ends. Meter 120 133.91 16,068.61

1.20 Supply and fixing of following sizes of MS conduit along with accessories in surface /recess

4.10 including painting in case of surface conduit,or cutting the wall and making good the same

in case of recessed conduit as required

Total of Wiring carried over to summary 16,068.61 11,97,866.00

5 LIGHTING FIXTURES

SITC of 2'X2' recessed mounted Luminaire with Maximum 36 Watt with Lumen output of 3600

lumen. The product should be SMD based and have non integral isolated driver with 3KV

inbuilt surge protection. THD<10%, PF >0.9,Product should have life class of 50K burning hour

at L70 B50 parameter, Luminiare operating temp 0 D to 45D. Internal wiring should have

teflon coted multi strand wires and external wire should have PVC coated multistrand wires.

SITC of Recessed mouted PDC lowdepth(height should not be more than 35mm) downlights

with maximum 12 Watt with minimum 1320 lumen.The product should be SMD based & have

non integral isolated driver with 2KV inbuilt surge protection. THD<10%, PF >0.9,Product

5.2 MR should have life class of 50K burning hour at L70 B50 parameter, Luminiare operating temp 0 Nos. 85 934.21 79,408.27

D to 45D. Internal wiring should have teflon coted multi strand wires and external wire should

have PVC coated multistrand wires.

SITC of Extruded Aluminium surface mounted 36Watt, 4000 lumen LED batten with PC Diffuser

and Spring Steel Clamps for Surface Mounting arrangement. Driver THD<15%, PF >0.9,with 2KV

5.3 MR inbuilt surge protection. Internal wiring should have teflon coted multi strand wires and Nos. 104 1,108.41 1,15,275.10

external wire should have PVC coated multistrand wires.

Total of Light Fixture carried over to summary 3,35,971.82

6 WIRING FOR DATA AND VOICE OUTLETS

Supply and fixing the following sizes of PVC medium duty ISI marked conduits (IS : 9537 Part-

III) complete with accessories such as bends, junction boxes, pull boxes etc., in recess or on

surface including cutting chases in the walls/floors and making good the same complete as

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/

PVC conduit as required.

Supply & fixing of Plug in type RJ45 computer data outlet in existing faceplate/ GI Box in

wall/furniture/floor complete as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet Each 51 119.00 6,069.00

7.5 Supply and fixing of the following types Face Plates complete with all accessories.

Supply & Fixing of Single Faceplate, Single Port (RJ45-DATA) square plate having spring

a shuttered front access for preventing ingress of dust, dimension as per commercially Nos. 8 95.72 765.74

available modular office furniture.

Supply & Fixing of Dual Faceplate, Duplex Port (RJ45 for data ) and (RJ-11 for voice) or as

b. required square plate having spring shuttered front access for preventing ingress of dust, Nos. 51 95.72 4,881.58

dimension as per commercially available modular office furniture.

Supply ,laying ,installing , testing and commmissioning of the 50 pair multi core 0.61 mm

annealed copper conductor PVC insulated and PVC sheathed armoured telephone cables

7.6 generally conforming to ITD S/WS-11-C and IS 1554 part I direct in ground /surface and / or in mtr. 120 359.93 43,191.97

existing pipe as required and includig making terminal joints, complete as required.

Supplying, installing, testing and commissioning of 24 port Cat 6 patch panels available with

block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded

CAT6 U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less

connector U/UTP unit in a block.

Supplying, installing, testing and commissioning of Cabinet. Size 24U (800 X 800 mm) (WXD)

following accessories, Width (mm) 800, Depth (mm) 800, Approx.Net Wt (kg) 75, CRCA 'D'

Grade thickness (mm) 1.2, RAL 9017(Matt Black), Glass: 4mm Toughened Tinted Glass

Door,Injected one piece polyurethane gasket on frame, Accessories: Cooling Fan (230V A/C

90 CFM) - 4 Nos, Cable Manager Metal- 4 Nos,PDU 230VAC - 1 No (12 nos. 6A/16A sockets

with plugs 6A/16A - 1/1pc & MCB 16A/32A -0/1 Pc), cable channel 100mm wide 24U- 2

Nos,Heavy Duty Stationary shelf M6 screws,washer,cage nuts (nickel coated))3 Nos. Earthling

Strips 150mm H - 1 No, Door Lock - 1 No, Castor Wheels (with Brake) - 2 Nos, Castor Wheels

(without Brake) - 2 Nos, Front Metal Band - 1 No. Packing: 5 ply cardboard & Inside 28 ply EP

foam. In the rack there must be maintained 1 U = 1.75 inches space. Nos. 1 etc complete as

Total of Data & Voice carried over to summary 1,13,415.10 3,46,069.00

8 CABLE TRAY.& RACE WAY.

Supply, fabrication and fixing of steel frame work in position for cable tray/Panels fabricated

out of 10 mm dia GI rods, ISA-40 MS angle iron, ISMC-50 channels, flats etc.complete with

providing of Anchor fastners and all necessary hardwares as required for fixing, including

cutting, bending, welding, drilling, bolting etc. as per design as required and painted with

one coat of primer and two coats of enamel paint of approved shade.

Supply and fixing of Perforated type 2mm thick Hot dip Galvanised G.I. cable tray of

following sizes complete with bend/tee joints, coupling plate & nuts bolts etc. as required for

fixing and including the cost of providing loop earthing with 2 nos. 50 mm x 6 mm GI earth

strips complete as per specifications, as required and as below.

8.2 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only)

Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with

internal partition/compartmentized of the following sizes including providing removable 3

mm thick GI cover, knock out holes and fixing accessories earthing with 8 SWG copper earth

wire complete as required including floor supports, bends, access boxes, tap off boxes and

cross over as per specification and site requirement. (overhead / wall mounted recovery &

function boxes shall be 1.6 mm thick)

a) 300 mm wide x 38 mm deep raceway RM 20 2,548.40 50,967.93

b) 225 mm wide x 38 mm deep raceway RM 30 2,152.63 64,579.04

c) 150 mm wide x 38 mm deep raceway RM 40 1,576.73 63,069.31

d) 100 mm wide x 38 mm deep raceway RM 40 1,201.44 48,057.65

Providing and fixing 350 x 350 x 60 mm deep 2 mm thick GI sheet junction box including

providing 3 mm thick stainless steel cover as per specification.

Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet junction box including

providing 3 mm thick stainless steel cover as per specification.

Total of Raceway carried over to summary 3,34,706.65 1,17,070.00

7 IP BASED CCTV SYSTEM

7.1 1.20 Supply and fixing of following sizes of MS conduit along with accessories in surface

/recess including painting in case of surface conduit,or cutting the wall and

making good the same in case of recessed conduit as required

7.2 Supply, installation, testing and commissioning of 2MP 2.8mm/3.6mm wide angle

fixed lens IR Dome Camera 1/3" Progressive Scan CMOS;

H.265+/H.265/H.264+/H.264/MJPEG; Colour: 0.01 lux @(F1.2, AGC ON), 0 lux with IR;

25fps/30fps(2560×1440, 1920×1080); 3 VCA functions; 3 streams; 3D DNR; ICR; EXIR

2.0, up to 30m; DC12V&PoE; Built-in micro SD/SDHC/SDXC slot.

7.4 Supply, installation testing and commissioning of Network Video recorder Linux

based to manage and control all the cameras from control room. Software shall

support maximum 32 channel with joystick controller. 256Mbps Bit Rate Input

Max(up to 32-ch IP video), 4 SATA Interfaces, alarm I/O: 16/4, 1.5U case,19" with

4x6TB i.e. 24TB HDD inside Nos. 1 Rs. 49,091 Rs. 49,091

7.6 Supply, installation, testing and commissioning of Video Management software

enabling security related personnel to easily and remotely gather video evidence,

monitor live situations, and configure and maintain a video surveillance system

over Ethernet consisting of digital video recorders (DVRs), hybrid digital video

recorders, network video recorders (NVRs), analogue video cameras, and IP video

cameras should support Detachable Viewers –users have the ability to detach

Viewer panels and move them to other (or the same) monitor(s). A maximum of

two (2) Viewers can be detached for a total of 75-up video tiles [two (2) detached

and one (1) core Viewer.

7.7 Supply Installation Testing & Commissioning of 21 inch Full HD LED monitor including

wall mount brackets/ clamps/ desk mounting stand. Nos. 1 Rs. 33,969 Rs. 33,969

7.8 Supply and fixing of RJ45 Connector Nos. 14 Rs. 274 Rs. 3,836

7.9 Supplying and fixing in position GI box for data outlet suitable for fixing of RJ 45

face plate complete as required. Nos. 14 Rs. 87 Rs. 1,223

7.10 Supply & Fixing of PCB based Information Outlet (I/O) RJ45, TIA-568C Category-6,

Termination of Catergory-6 UTP Cable, UL listed, Shall conform to Category-6 as

per the EIA/TIA-568C.2, Shall support network line speeds up to 1 Gbps, Shall have

RJ-45 type connector with bend limiting and strain relief boot for securing IDC

contacts from external forces and for maintaining the bend radius of the cable,

Shall have minimum durability of 750 mating cycles and 200 termination cycles.

Shall be certified by independent labs like ETL/GHMT for compliance to EIA/TIA-

568C.2. The outlet shall be fixed in existing box & cover plate in wall/furniture/floor

complete as required.

7.11 Supply & Fixing of Single Faceplate, Single Port (RJ45-DATA) square plate having

spring shuttered front access for preventing ingress of dust, dimension as per

commercially available modular office furniture. Nos. 14 Rs. 96 Rs. 1,340

7.12 Supply, installation, testing and commissioning of Rack 12U with all accessories viz 4

Nos of mounting hardware, fan tray, power strip and cable manager as required

as per site. Nos. 1 Rs. 3,397 Rs. 3,397

7.13 Supply & Laying in existing conduits/raceway/furniture of 4-pair Unshielded twisted

pair cable with a cross filler (+), meeting Category 6 standards as per TIA-568C.2.

The cable shall be tested till 600 MHz or more from independent laboratories like

ETL for 4 connections. Test Certificate from independent labs like ETL shall be

required. RM 500 Rs. 58 Rs. 29,185

7.14 Supply & Fixing of UTP Jack Panel UL listed, loaded with 24 no's UTP ports for PCB

based IO Jacks (RJ45, TIA-568C Category-6), having integrated bonding bar or

other mechanism for grounding, loaded with individually replaceable 24 nos.

Category-6 I/O Jacks complying with TIA-568.C.2. Shall be 6 port module

construction for better cable dressing at the rear. The jacks shall have RJ-45 type

connector with bend limiting and strain relief boot for securing IDC contacts from

external forces and for maintaining the bend radius of the cable.

7.15 Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance

modular plug at each end. Patch cord cable shall be offered in multiple coloured

UTP cable for design flexibility with a clear strain relief boot on each modular plug.

All patch cords shall be compatible with both T568A and T568B wiring schemes.

UTP Cable, 2 Meter. Nos. 14 Rs. 182 Rs. 2,548

7.16 Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance

modular plug at each end. Patch cord cable shall be offered in multiple coloured

UTP cable for design flexibility with a clear strain relief boot on each modular plug.

All patch cords shall be compatible with both T568A and T568B wiring schemes.

UTP Cable, 1 Meter. Nos. 14 Rs. 91 Rs. 1,274

7.17 Supply Installation Testing & Commissioning of Managed Layer -2 Switch with Power Nos

on Ethernet (PoE) enabled, 24 Port Fast Ethernet Web Smart Switch, including 2

Gigabit BASE-T and 2 Gigabit Combo BASE-T/SFP. 1 Rs. 10,312 Rs. 10,312

TOTAL OF IP BASED CCTV SYSTEM CARRIED OVER TO SUMMARY Rs. Rs. 3,04,246

20 kVA UPS with 15 minute backup

Supply, unloading, shifting, installation, testing & commissioning of micro processor

controlled following rating UPS capable of operating in parallel redundant mode

so that if any one UPS fails the other can supply 100% load, IGBT based rectifier to

achieve input THDI < 4% and input power factor of greater than 0.99 at 100%

loading with 3 level Inverter Topology. True Online Double Conversion (VFI as per

IEC 62040-3) UPS using PWM IGBT technology , 3 Phase input and 3 phase 415 V

output UPS system; and comprising of the following complete as required and as

per specification: set 1 Rs. 5,08,216 Rs. 5,08,216

Fully rated Rectifier cum charger unit and 100% rated Invertor unit Integrated in UPS

Fully rated Inbuilt static switch at the inverter output and 100% rated Inbuilt static

switch at the static bypass line integrated in UPS module.

Web-enabled Monitoring and Management through SNMP protocols for multi-OS

environments with below features.

Giving notifications like e-mail, paging notification, broadcast notification, battery

replacement notification, run event-based scripts.

Event logging, data logging and action logging (with date, time, description of

fault and event).

Fully rated Inbuilt Maintenance Bypass Switch for the continuous operation of the

load during maintanance.

Local notification through audible alarm.

Fully rated Battery Circuit Breaker with under voltage coil & deep discharge

protection to the batteries.

One time cost of replacement of PCBs to be considered, in case conformal

coated PCBs are not available .

(Vendor to specify the cost considered)

Battery Banks comprising of Valve Regulated Lead Acid Sealed Maintenance Free

batteries of minimum 5years design life to provide 15 minutes backup at 20kVA

,0.9PF, ECV=1.7V with each UPS. Minimum VAH required with each UPS 11232 VAH

.The batteries shall be installed on shelves of rack for quick replacement and

servicing. The temperature sensor shall be provided in the battery section for

temperature compensated charging. The bank of batteries shall comprise of

required numbers of batteries connected in series.

Vendor to provide complete details of make of Batteries, ampere hour ratings, no.

of Batteries, Expected life, Final discharge voltage, Nominal float voltage, Battery

recharge time & configuration of back up time, Battery sizing Calculations

Supply, unloading, installation, testing & commissioning of open type MS racks

including top fully cover to protect from falling object to house SMF batteries for 30

kVA UPS system along with suitable interconnecting links, moulded case circuit

breaker having Ithermal, Imagnetic & automatic U/V trip mechanics for Battery

Banks etc. complete as required & as per specifications.

UPS Testing with External Load Banks (To be provided by vendor) for 8 hours at full

load shall be included in the offer incase Phantom Loading feature as specified in

the data sheet is not available in the UPS.

Supply, laying, testing & commissioning of flexible single core copper cable for

interconnections between UPS to UPS, UPS to batteries( 10 m) , complete as

required for each UPS.

TOTAL OF UPS & INVERTER SYSTEM CARRIED OVER TO SUMMARY Rs. Rs. 5,08,216

Project : JEEVAN TARA BUILDING

ESTIMATED COST FOR FA & PA SYSTEM

A. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : MR. DSR.

DSR Total Total

Sr. No Description Unit Qty Unit Rate

2018.No. amount amount

Supplying, installation, testing and commissioning of micro processor based intelligent addressable

main fire alarm panel, central processing unit with the following loop modules and capable of

supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and

loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display

with touch screen or other keypad and minimum 4000 events history log in the non volatile memory

(EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free

batteries with automatic charger. The panel shall have facility to connect printer to printout log and

facility to have seamless integration with analog/digital voice evacuation system (which is part of the

schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be

compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per

specifications.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal Pcs 35 2846.00

2 17.2.4 detector complete with mounting base complete as required. 99610.00

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of Pcs 1 2713.00

3 17.2.9 rise cum fixed tempreature thermistor complete with base as required. 2713.00

Supplying, installation, testing & commissioning of addressable manual call point complete as required. Pcs 2 3859.00

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. Pcs 2 3494.00

Supplying, installation, testing & commissioning of fault isolator complete with base as required. Pcs 2 3257.00

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box Pcs 10 263.00

7 17.2.5 having two LED, metallic cover complete with all connections etc as required. 2630.00

B CABLES & ACCESSORIES FOR FAS :

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper RM 250 141.00

1 17.5.2 conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. 35250.00

C SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES :

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player Pcs 1 126399.00

1 17.3.1 (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for 126399.00

voice evacuation complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at Pcs 1 96767.00

2 17.3.6 240 volt AC supply complete as required. 96767.00

Supplying, installation, testing & commissioning ofceiling/wall mounted loud speaker, 3/1.5 Watt in ABS Pcs 16 2416.00

enclosure complete as required.

D CABLE & ACCESSORIES FOR PA SYSTEM

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing

1 17.5.3 surface / recessed steel conduit of following pairs, cores and size including connections and

interconnections etc. as required..

17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm RM 250 51.00 12750.00

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and RM 200 50.00

accessories like coupler etc. as required.

GRAND TOTAL Rs. 684902.00

GRAND TOTAL Rs. 684902.00

BOQ - Fire ALarm PA system

Electrical Consultant : DCS Consultant Sons

ESTIMATED COST FOR ACCESS CONTROL SYSTEM

Sr. No Description Unit Qty Rate Amount

11 ACCESS CONTROL SYSTEM

Supply, Installation, Testing & Commissioning of Access Control

System with RFID, Figure Print and Pin Authenication with 3,000

Fingure Print Capacity, 10,000 Card Capacity, 50,000 Transaction

Log Capacity, Built In Buzzer, 128X64 OLED Display, 3x5 Keypad

and Bells, Weigand Output, USB, TCP/IP Network Interface, IP 65

Supply, Installation, Testing & Commissioning of 2 Door/ 2 Reader

IP Controller accommodates a card database of 55,000 cards,

and a transaction buffer of 45,000 transactions,TCP/IP, USB, Serial

Interface unit, Relay Switching Port.

3 Supply, Installation, Testing & Commissioning of Proximity Cards. Nos. 25 314.95 7,873.76

Supply, Installation, Testing & Commissioning of Electromagnetic

Lock 600 lbs, single leaf, LED Status Display, includes Door Sensor,

i/c making conection, integration, testing etc. complete as

required on site

Supply, Installation, Testing & Commissioning of Power Supply 12V 2

5 A for Access Control Reader and Door Lock Unit, Complete in all Nos. 2 3,192.45 6,384.91

respect as required at site.

Supply, Installation, Testing & Commissioning of Alagtech U/L

Clamp made of aluminium anodised for EM Lock on the surface

of frame/structure etc. i/c alignment etc. for smooth operation of

Supply, Installation, Testing & Commissioning of 24 Port Gigabit

Switch, Auto MDI-MDIX for all port,Link Status Detection, 4.8 Gbps

Switching Capacity, Rack Mountable, Complete in all Respect as

required at site.

Supply, Installation, Testing & Commissioning of Access Control

Software for with Advance Access Management Module &

8 Advance Attandence Mangement Module. It should support Multi Nos. 1 74,442.85 74,442.85

company, Multi location, Multi department, Multi login with

different rights, Muti hierarchy of employee.

Total of Access Control System carried over to summary 3,01,049.75

S.No Item Description UoM Unit Cost (INR) Qty. Total Cost (INR)

Supply, installation, testing, commissioning and programming of following items-

SITC of 65" 4K UHD LED display with 400 Cd/m2

brightess, Contrast ratio:1200:1, Resolution: 3840

x 2160 (16:9), Viewing angle: 178° h/v, Response

time:8ms, Input ports: 2 x HDMI, 1 x DP, 1 x VGA,

1 65" LED Screen LAN, RS232 Control, 2 x 8W in built speakers, NOS Hardware 2,18,684 1 218683.70

input HDMI, VGA, and USB, Landscape and

Protrait Installation Option etc. The item to

include mounting bracket and all other required

accessories complete.

55" Full HD LED display, HDMI X 2, VGA X 1, Video

IN X 1, USB X 1, Audio IN X1, Audio Out X 1, SPDIF

X 1, RS232C x 1, 20W in built speaker, IPS LED

2 55" LED Screen NOS Hardware 1,20,782 1 120782.32

display, USB media player. The item to include

mounting bracket and all other required

accessories complete.

3 Ceiling Speakers Ceiling Speakers NOS Hardware 1,893 4 7570.05

4 Inwall Speakers Inwall Speakers NOS Hardware 7,501 2 15001.63

4-channel 100V bridgeable digital power

5 Audio Amplifier NOS Hardware 1,16,582 1 116581.87

amplifier, 4 x 120W

Supply, Installation, testing and commissioning

of 24 ethernet port 10/100/1000 PoE+ stackable

6 Network Switch NOS Hardware 1,25,000 1 124999.70

switch with 4 SFP+ ports and 2 fixed power

supplies. (Make- CISCO-L3 or equivalent).

Communication Method: SIP, H.323

Video Compression Method: H.261 (mainstream)

H.263, H263+, H.263++ (reception only), H.264

High Profile, H.264 Baseline Profile

No. of Channels: G.711/G.722/G.722.1/G.722.1

7 Video Conference System NOS Hardware 3,62,088 1 362088.48

Annex C: 1 MPEG-4 AAC-LD Mono: 1/ MPEG-4

AAC-LD Stereo: 2

Remote Camera Control: H.224, H.281

(Zoom/Pan/Tilt/Preset)

Encryption: SRTP (AES 128 bit), H.235 (AES 128 bit)

Multi Point Video

8 4-way HD continuous presence. NOS License 1,27,183 1 127183.02

Conferencing License

Should be equipped with a professional 1/2.8

inch image sensor with Full HD 1080p output

resolution and a high dynamic image quality of

60 frames per second.

Must have 20x optical zoom lens with

professional noise reduction and wide dynamic

range technology to deliver a clear image even

low light, backlight or the extreme contrast of

9 Full HD PTZ camera NOS Hardware 1,87,028 1 187027.96

brightness and darkness in the room.

The camera must utilize a highly efficient DC

motor servo controller to achieve high-speed,

quiet and precise positioning movements. It

should support 3G-SDI, DVI, component, and C-

Video interfaces allowing four simultaneous

outputs with the best possible image quality and

compatibility with all video equipment.

Supply, installation, testing and

commissioning of digital / ip based epabx

system in simplex mode and all cards hot

swappable and expandable upto 1000

ports and with all features as per technical

specifications along with hardware for the

(KX NS 1000 Panasonic model or equivalent

a.124 analog extensions

b. 20 NOS. digital extensions

c. 16 NOS. analog trunk

10 EPBAX d.1 no isdn pri (30 channels) System System 3,90,120.54 1.00 390120.54

f.built in least cost routing

g.snmp based system administration

H.SUPPORTS H-320 PROTOCOL FOR VIDEO

CONFERENCING BEHIND EPABX

i.supports dect connectivity - digital

cordless extension

j.lan connectivity

k.music on hold

l..voice mail for all users

m. Online 2KVA UPS dedicated for EPABX

Supply,installation and commissioning

of digital phones with the following

features(KX DT 543 Panasonic model or

i) tiltable graphical display, 2 lines

11 EPBAX monochrome keys Nos 20,921.30 1.00 20921.30

ii) Programmable key

iii) 3 way navigator

iv) 7 fixed function keys

v) hands free talking

with built in speaker complete

Supply, installation and commissioning

of desktop analog telephone complete

Sub Total of Serial No. D 17,06,095

Office for NMC Scope Complex, New Delhi

BOQ FOR PLUMBING & FIRE FIGHTING

SECTION DESCRIPTION S.I (AMOUNT) N.S.I (AMOUNT)

A SANITARY FIXTURES & FITTINGS 38466.90

B WATER SUPPLY 11484.45 0.00

C INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES) 49876.30 0.00

D SPRINKLER PIPING & ACCESSORIES 370237 82631.86

Total Cost ( Carried Forward) in Rs. 552696.51

BOQ FOR PLUMBING & FIRE FIGHTING

SUB HEAD A: SANITARY FIXTURES & FITTINGS

DSR Rate NS Rate DSR -

SL. NO. DESCRIPTION OF ITEMS UNIT Qty Amount NS Amount (Rs)

1.1 Providing & fixing stainless steel sink R.S. or C.I. brackets

painted, 40mm C.P. waste, C.P. brass chain and rubber plug,

40mm C.P. cast brass bottle with necessary union complete

including cutting and making good the walls wherever

Stainless steel sink single bowl with drain board(size

510x1040mm) of approved

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 12069.43 12069.43

1.2 Providing & fixing Sink Mixer with Swinging Casted Spout (Wall

Mounted Model) with 450mm long Copper Pipes & Brass

Nuts.CP brass wall flange NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 3729.97 3729.97

1.3 Providing & fixing, testing and commissioning of storage type

electric water heater with automatic thermostatic control

electric element, pressure release valve, brackets fixed to

expansion fasteners with M.S. nuts and bolts all complete

including cutting and making good the walls wherever

25 litres capacity (Horizontal /Vertical type1.5 kw electrical

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 19385.00 19385.00

1.4 Providing & fixing 15 mm dia C.P. brass bib cock with C.P.

wall flange of approved quality. NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 1641.25 3282.50

i. Detail of Sanitary fixture are for the information of the

Contractor,however model/makes of all sanitary fixtures shall

be selected by Architect/Interior designer/Project manager

and the same shall be binding for execution.

ii. No additional fixing cost shall be paid for change in type of

sanitary fixtures.

iii. Contractor to receive all the above mentioned items & store

at place as directed at site.

TOTAL CARRIED OVER TO SUMMARY 38466.90

SUB HEAD B: WATER SUPPLY

SL. DSR Rate NS Rate DSR -

DESCRIPTION OF ITEMS UNIT Qty Amount Amount

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

(CPVC) plain & brass threaded fittings including fixing the pipe

with clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

20 mm nominal outer dia pipes. Metre 5.00 325.10 1625.50 18.7.2

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

clamps at 1.00 m spacing. This including jointing of pipes & fittings

with one step CPVC solvent cement and the cost of cutting

chases and making good the the same including testing of joints

complete as per direction of engineer in charge.

Concealed work oncluding cutting chases and making good the

20 mm nominal outer dia pipes. Metre 15.00 513.75 7706.25 18.8.2

Providing and fixing brass stop cock of approved quality

3 complete. 18.16

20 mm nominal bore Each 1.00 327.95 327.95 18.16.2

Providing and fixing C.P. bass angle valve for basin mixer and

geyser points of approved quality conforming to I.S:8931 a) 15

5 mm nominal bore. 18.53

15 mm nominal bore Each 3.00 500.35 1501.05 18.53.1

Providing and fixing unplasticised P.V.C connection pipe with

PTMT Nuts coller and bush of approved quality and colour.

15mm nominal bore with 45cm length Each 3.00 107.90 323.70 18.74.2

Sub-Total of Water Supply Installation, Separate for Scheduled & Non-Scheduled Items 11484.45

SUB HEAD C: INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES)

SL. DSR Rate NS Rate DSR Amount NS Amount DSR -

DESCRIPTION OF ITEMS UNIT Qty

Providing and fixing cast iron trap of self cleansing design with cast

iron screwed down or hinged grating with or without vent arm

complete, including cost of cutting and making good the walls and

100 mm inlet and 100 mm outlet centrifugally cast (spun) iron S&S as

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

75mm dia cast (spun) iron S&S pipe Metre 35 1,042.10 36,473.50 17.35.2.2

Providing and fixing single equal plain junction of reqd. degree with

access door, insertion rubber washer 3mm thick, bolts and nuts

3 complete. 17.43

Sand cast (spun) iron pipe IS-3989 Each 4 573.80 2,295.20 17.43.2.2

Providing and fixing bend of required degree with access door,

5 insertion rubber washer 3mm thick, bolts and nuts complete. 17.38

Sand cast (spun) iron pipe S&S as per IS 3989. Each 4 453.40 1,813.60 17.38.2.2

7 Providing and fixing collar. 17.57

Sand cast (spun) iron pipe S&S IS-3989 Each 2 271.45 542.90 17.57.2.2

Providing and fixing MS holder bat clamps of approved design to cast

iron (spun) pipe embedded in and Including cement concrete blocks

10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

aggregate 20mm nominal size) including cost of cutting holes and

8 making good the walls etc. 17.37

Painting sand cast iron / centrifugally cast iron( spun) iron soil, waste

and vent pipes and fittings with paint of any colour such as

chocolate, grey or buff etc. over a coat of primer (of approval

12 quality) for new work 17.65

75mm dia cast (spun) iron S&S pipe Metre 20 52.90 1,058.00 17.65.2

Sub-Total of Drainage Installation, Separate for Scheduled & Non-Scheduled Items 49876.30 0.00

SUB-HEAD - D - SPRINKLER PIPING & ACCESSORIES

DESCRIPTION OF ITEMS DSR

SL. DSR Rate NS Rate NS Amount DSR -

UNIT Qty Amount

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming

to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts

1 bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required : 7

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with

2 bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required : 11

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all

accessories as per manufacturer's specifications.

4.1 CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 1 14,782 14782.39

4.2 ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 16 1,830 29280.93

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of

rating 68 degree centigrade with required accessories :

5.1 Pendent Sprinkler NOS. 5 484 2420 21.1

5.2 Horizontal side wall sprinkler NOS. 5 579 2895 21.3

5.3 Uprigth Sprinkler NOS. 41 484 19844 21.2

5.4 Concealed Sprinkler NOS. 41 1397 57277 21.4

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of

stainless steel complete with 15 NPT on reducer thread with maximum working

pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT

male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple,

2 side brackets, center bracket, stockbar of following sizes complete as required.

Providing and fixing signages printed on photoluminescent U1000 aluminium sheet of

1.0 mm (+ -10%) containing lumigen II as base chemical, covered under UV stablized

7 coating and of appropriate size including fixing on wall, door, ceiling etc. with proper

clamps, hangers, cleats anchor fasteners etc. complete in all respacts as diercted by

Engineer-in-charge SQ INCH 1200 22 26400 NS

Providing, jointing and testing of automaticaly operated Halotron fire

8 extinguishers(cap-5kg,temperature rating-68degc,test pressure-30bar) complete with

all accessories/fittings. NOS. 1 12,169 12168.54299 NS

TOTAL CARRIED TO SUMMARY 370237 82631.8607

PART - I (VRV/VRF SYSTEM)

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate Amount

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/ Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and

heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum

two compressors for above 14 HP modules, microprocessor based Controller, top

discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with

1.1 suitable foundation etc. complete as required.The unit shall deliver the rated

capacity at AHRI Conditions and work even at 50°C ambient temperature without

tripping.The unit shall be suitable to work on 400V+/-10%, 3 Phase, 50Hz AC power

supply.The unit shall be filled with first charge of the refrigerant and ready for use as

required.The COP at AHRI conditions shall not be less than 3.1 and IEER not less than

a Supply VRF/VRV Outdoor Unit with Heat pump Per HP 8 16415 131320

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following minimum capacity 4-

wayflow VRV/ VRF Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre-filter, fan section with low noise fan/ dynamically

balanced blower, multi speed motor, coil section with DX Copper coil, electronic

expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

2 isolation, cordless remote control etc., suitable for operation on single phase

230V±10%, 50 HzAC supply, complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from BMS System. The

cooling capacity of indoor unit will be at air inl et conditions of 27 Degree CD Band

19 Degree CWB temperature.

4-Way Cassette type

3.0 REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and

Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant

piping for VRV/ VRF system, complete with fittings, with suitable adjustable ring type

DSR 2019 hanger supports, jointing/ brazing including accessories, insulated with XPLE Class O

VRF/VRV tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves

sections of specified thickness as given below for Suction and Liquidlines, all

accessories as per specifications etc. as required :

3.1 5.4 15.9 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm) Rmt 15 588.0 8820

Supplying and installing of following size of perforated hot dip galvanized G.I cable

tray with perforations not more than 17.5%, in convenient sections, joined with

4 MR connectors, suspended from ceiling with G.I suspenders including bolts and nuts,

etc. for carrying refrigerant pipe in outdoor application as required.

4.1 225mm width x 50 mm depth x 1.6 mm thickness Rmt 30 716 21494

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe ,complete with fittings,

supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and accessories

as per specifications, drawings.

6 MR Imported fittings Y-joints and headers etc. Nos 3 4281 12844.20151

7 Control & Trasmission Wiring

MR Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper in Mtr 40.00 171.49 6859.64

suitable conduits between indoor and outdoor unit.

8 MR SITC of 1.0 T split with rotary compressor of 5 Star rating Inverter technology Nos. 2.00 44553.32 89106.65

approved make make inclusive of 5 year warranty on compressor all complete.

(Note- Indoor and outdoor unit should have copper Condensor and cooling coil.)

9 MR Timer for Split ac for Server Nos. 1.00 3864.23 3864.23

10 MR Providing and fixing lockable MS cage for outdoor units primered and painted black. Nos. 1.00 4585.92 4585.92

11 MS Standard for ODU

MR Providing and fixing MS Stand for ODU along with vibration pad as per approved Nos. 1.00 8766.97 8766.97

SUB TOTAL OF PART - I 3,99,134.60

PART - II (HVAC/ DUCTING SYSTEM)

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate Amount

A AIR DISTRIBUTION SYSTEM

1.0 GSS DUCT (Factory Fabricated Duct)

Supply, installation, balancing and commissioning of factory fabricated GSS sheet

metal rectangular/round ducting complete with neoprene rubber gaskets, elbows,

16.12.1 splitter dampers, vanes, hangers, supports etc. as per approved drawings and

specifications of following sheet thickness complete as required.

2.0 Supply Air Diffusers

Supply , installation , testing and commissioning of supply air diffusers of Powder

coated Aluminium with Aluminium volume control dampers with anti smudge ring

and removable core. Diffusers shall be as per specification & the sizes will be as

per drawings and schedules :

3.0 Return Air Diffusers

Supplying, fixing testing commissioning of Return air diffusers of powder coated

16.18 aluminium without volume control dampers with anti smudge ring & removable core. Sqmt 14 7,559.00 1,05,826.00

4.0 Fire Damper

Supplying, Fixing,testing and commissioning of fire damper in supply air duct/main

branch and return air path as and where required of required sizes i/c control wiring,

the damper shall be motorized and spring return so as to close the damper in the

event of power failure automatically and open the same in case of power being

restored. The spring return action shall be inbuilt mechanism and not externally

mounted. the damper shall also be closed in the event of fire signal complete as

required and as per specifications.

4.2 16.20.2 Actuator (Rated torque-10 N.m/m2) Each 2 9,212.00 18,424.00

B INSULATION & ACOUSTIC

1.0 DUCT INSULATION

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish

closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable

adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick

self adhesive nitrile rubber tape insulation complete as per specifications and as

2.0 DUCT ACOUSTIC LINING

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick

resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section

of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue

16.21 paper and 0.5 mm thick perforated aluminum sheet fixed to inside Sqmt 30 647.00 19,410.00

surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc.

complete as required and as per specifications.

SUB TOTAL OF PART - II 8,82,369.00

TOTAL OF PART - I & PART - II (CARRIED OVER TO SUMMARY) 12,81,503.60