REPAIRS TO WOODEN ,STEEL FURNITURE, GI CHARPOY / CHARPOY FOLDING IP WITH HANDTOP REPLACEMENT OF LOCK HANDLE,GI TUBE, NYLON NEWAR, PLY AND RE-CAN OF CHAIR AND PAINT TO STEEL FURNI AT RCMA, DOMESTIC,OFFICE AREA OF DGAQA, AFLE, 11 BRD OJHAR ,BORGAD

Amount

Repairs to Steel Furniture - 1 (a) Table Office Clerk/Officer Steel (FD-1005) :- Taking out existing worn out front & side portion complete of the drawer. Supply & fix new front & side portion complete with lock to the drawer. Removing the dents and bents welding/riveting the damaged portion of the drawer and rectifying portion of the drawer and rectifying other defects to have smooth movement of the drawers all as specified and directed.

1 (b) Table office officer steel (FD-1003) Taking out worn out following components without damaging the other components. Supply the new components made out of 25mm square 16 gauge MS Square tubing and fixing the same by welding to the in place of removed components :- (i) Legs

(ii) Top rails long

(iii) Top rails short

(iv) Foot rest long stiffners

1 (c) Taking out worn out following components without damaging the other components. Supply the new components made out of 25mm square 16 gauge MS Square tubing and fixing the same by welding to the Table office clerk steel in place of removed components :- FD-84, 1004, 1005 (i) Legs

(ii) Top rails long

(iii) Top rails short

(iv) Foot rest long stiffners

(v) Stiffeners short

1 (d) Removing dents and bents and carrying out the minor repairs, repairs to locking device complete of the drawers to have smooth movement. Material and labour for preparation of steel surface of table providing high class glossy finish synthetic enamel paint over a coat of red oxide primer wherever required. including providing of PVC shoes to the legs:- (i) Table office clerk steel

(ii) Table office officer steel

1 (e) Removing of old damaged/unserviceable Table tops from table steel and replacing the top with 18 mm thick pre-laminated particleboard (one side teak face another white balancing coat) 6 mm thick teak wood beading all around and fixed with suitable size of screws to table frame as per drawing including polishing to teakwood edging all as specified and directed by Engineer-in- Charge (i) Table office clerk steel FD-84, 1004, 1005

(ii) Table office officer steel FD-1003

1 (f) Removing existing unserviceable old locks from table. Supply and fix new lock, made out of steel body Grade I type of 50mm size with six brass levers and with duplicate keys, all and fixed to the steel table with screw, complete all as specified and directed.Make:-godrej or equivailent

2 (a) CHAIR CB STEEL WITH/WITHOUT ARMS 14(a) Taking out the old worn out and unserviceable portion of MS tubular frame of chairs as listed below. M&L for new portion/part duly fabricated to shape and size as shown on drawing to match/fit in the chair and made out of 25mm dia 16 gauge MS tubing. Welding the new fabricated portion/part to the chair frame all as specified and directedby Engineer-in- Charge . (i) Complete all shape base portion of steel chair frame

(ii) Pair of L shape vertical base portion of steel chair frame

(iii) 25 mm dia 16 gauge 460mm long on tubing support between the seat and back frame of each steel chair frame

(iv) 50 x 25 x 3mm Mild Steel cleats with a hole to hole a screw, four cleats each, to seat and back frame of each steel chair frame to support wooden seat/back wooden frame all as specified and directed

2 (b) Removing damaged unserviceable Seat frame from chair CB tubular steel with arm/without arm and back frame from chair CB steel with/without arm supply and fix new seat and back frame complete with suitable size of screw as specified all as per drawing and directed by Engr-in-Charge. (i) Back frame for chair CB tubular steel with arm

(ii) Seat frame for chair CB tubular steel with arm

(iii) Back Frame for chair CB tubular steel without arm

(iv) Seat frame for chair CB tubular steel without arm

(v) Arm rest for Chair CB steel with arm

3 (a) Repairs to Almirah Large/ Medium Steel : FD-243, 1032, 67(M), 1031 Removing existing unserviceable old locks from Almirah steel. Supply and fix new lock, made out of steel body Grade I type of 75mm size with six brass levers (Make Aligarh or equivalent as approved by GE) and with duplicate keys, and fixed to the steel Almirah with four screw or as required, complete all as specified and directed

(b) Removing existing unserviceable handle from steel Almirah. S & F new steel chromium plated handle of 150mm size all as per Godrej pattern and fixed to steel Almirah with hexagonal nut and steel pin of appropriate size complete all as specified and directed.

(c) Taking out existing locking device carrying out all minor repairs, dent and bents to the Almirah Large/Med steel refixing the same to the steel Almirah with providing of new screw or nut and bolt all as specified and directed by Engineer-in-Charge

(d) M&L for removing old worn out hinge from Almirah Large/Med Steel and S&F new hinge of best quality and fixed with welding.

(e) Removing dents, bents of steel Almirah, welding to broken portion. Rectifying all minor defects and repairs. Material and labour for preparation of steel surface of Almirah (inside & outside surface) including doors shelves and legs. Providing high class glossy finish synthetic enamel paint over a coat of red oxide primer wherever required. All complete specified shown on drawing and directed for following Almirah:- (i) Almirah Large Steel with Shelves

(ii) Almirah Med Steel with Shelves

M&L for removing/scrapping old worn out paint from the following steel furniture by sand paper and painting with two coats of OG synthetic enamel paint make Asian/Berger over a coat of red oxide primer. Rest all as specified in the drg and as directed by Engr-in-Charge. 4 (a) Almirah Large Steel 1/2 H 1/2 S steel FD-1033

(b) Almirah Steel with Mirror 1950x1500x600mm TP

(c) Shoe Rack Steel 1500x650x300mm TP

(d) Chair CB Steel with Arms FD-75

(e) Almirah Large Steel with shelves FD-109, 67 (M), 1031

(f) Almirah Med Steel with shelves FD-243, 1032

(g) Table office officers steel FD-1003

(h) Table office clerk steel FD-84, 1004, 1005

(j) Rack Shelf with 4 Shelves

(k) Locker Bed Side

(l) Chair Verandah Steel Map (Black)

5 (a) Charpoy GI Pipe with Nylon Newar- FD-220, 221 Removing of unsv nylon tape newar from Charpoy GI Pipe, Tightining of entire the loose frame and converting into Hardtop Charpoy by providing 12 mm thick commercial plywood BWR grade with teak wood beading to complete plytop edging, of size 12 mm wide and 5mm thick fixed Fevicol adhesive and pin panel and 3 Nos MS Square tube of size 25mm x25mm, 16 guage alongwith of charpoy , fixed duly welded with frame as support to plywood with hole and fixd with requred size Nuts & Bolts all as specified and directed by Engr-in-Charge. Make - Century, Kitply, Greenply, Anchor, Hindo)

(b) Removing damaged unserviceable GI Elbow 3 Way 32mm dia from charpoy GI pipe. Supply and fix new GI elbow 3 way 32mm dia medium grade with ISI including GI Check Nut where ever requried fixing as per drawing, all as specified and directed. (Refer to FD-220)

(c) Removing damaged unserviceable long rail of charpoy GI pipe and replacing with new long rail of 32mm dia medium grade GI pipe with ISI mark duly threaded at both ends and fixing as per drawing all as specified and directed by Engineer-in-Charge. Make- Parkash/Surya/Jindal/Swastik) (Refer to FD-220)

(d) Removing damaged unserviceable short rail from Charpoy GI pipe and replacing with the old long Rails/pipes obtained from Ser Nos 03 above and converting by cutting & threading suitably and fixing as per drawing, all as specified and directed.(Refer to FD-220)

6 (a) Charpoy with Hardtop IP (FD/E6/MAP/II/01) Removing of unsv/damaged plytop and Supply and fixing new 12mm Ply with BWR grade commercial to existing Charpoy of size all as shown in drg. Make- Kitply/ Sainik/ Century/ Greenply/ Anchor

7 (a) Bed Hard Steel Map (FD/E6/MAP/08R Removing of unsv/damaged plytop and Supply and fixing new 12mm Ply with BWR grade commercial to esicting charpoy of size all as shown in drg. Make- Kitply/ Sainik/ Century/ Greenply/ Anchor

(b) Removing of unsv/ damaged particle board of Head Rest and Foot Rest and Supply & Fixing new one of exterior grade with PVC beading around to Bed Hard Map of size all as shown on drg. Make- Kitply/ Sainik/ Century

(c) Material & Labour for welding to broken joints or Tighting of entire frame by means of nuts & bolts of Bed Hard Map complete all as specified and directed by Engr-in-Charge

8 (a) CHAIR VARANDAH FD-256 :-Removing of old cane and providing new plastic cane white coloured indigenous not made of recycled plastic, as per existing pattern and size for chair verandah after applying one coat of synthetic enamel paint (white colour) on frame complete all as specified, shown on drawing and as directed by Engr-in-Charge.

(b) M&L for spot welding joints of frame of chair varandah as where required

(c) CHAIR VARANDAH PVC (FD/E6/MAPII/06) :- Removing of old PVC seat / back and providing new PVC moulded seat and back white color to the existing frame of chair varandah after applying one coat of synthetic enamel paint white color complete all as specified and directed by Engineer-in-charge.

REPAIRS TO WOODEN FURNITURE : Removing the unserviceable/worn out components without damaging the other components or structure of chairs, supply and fix new components given below. The new components shall be made of Ist class Hard wood ( Indian Teak wood ) as shown in drawings and also to match with the existing components including sanding, rubbing and applying one coat of French polish to complete chair or only component after repairs (Note : After complete repair of component contractor has to assemble/tightening all the assessories of chairs) 9 (a) CHAIR EASY FD-17, 201, 229 (i) Front Leg

(ii) Rear Leg

(iii) Sides and rear rail of seat frame and side rail of back frame

(iv) Arm rest

(b) CHAIR DINING ( FD-203, 228, 279 ) (i) Front Leg

(ii) Rear Leg

(iii) Top rail

(iv) Back rest

(v) Stiffener

Removing of old cane and recanning with new indigenous plastic cane not made of recycled plastic as per existing pattern and size of cane for any type of chairs (seat & back) as specified and shown in the drg and as directed by Engr-in-Charge. 10 (a) Chair easy

(b) Chair writing

(c) Chair dining

(d) Chair Dining PVC Seat (FD/MAP-II/05)

Material and labour for polishing of furniture including scrapping of rough surface and old worn out polished layer with scrapper /sand paper for smoothing the surface and polishing the same with one coat of approved quality of french polish to glossy finish for the following items of furniture :- 11 (a) Chair easy FD-17, 201, 229

(b) Chair Dining FD-16, 149, 226, 279

(c) Chair Dining Cushioned

(d)Sofa set 5 seater in 3 pieces FD-258, 373

(e) Table Peg FD-25, 236, 277

(f) Table Dining 1200x900mm

(g) Table 900x600 without drawers/with drawer

12. M&L for removing/scrapping old worn out paint from the following steel furniture by sand paper and painting with two coats of Olive Green/ Gray (as per existing) synthetic enamel paint make Asian/Berger over a coat of red oxide primer. Rest all as specified in the drg and as directed by Engr-in-Charge (a) Almirah Large Steel Glazed of 1986X910X480mm (FD-104M)

13. Chair Visitor Cushioned/Chair Tubular Padded Seat & Back - Taking out unserviceable/worn out the following componets of the chair exectutive Vister S&F new components as per existing shape and size to the chair color as approved or as directed by Engr-in-Charge:- (a) Cushioned seat

(b) Cushioned back

(c) PV Handle

14. Chair Executive Revolving High back/ Mid Back - Taking out unserviceable/worn out the following componets of the chair computer, S&F new components as per existing shape and size to the chair color as approved or as directed by Engr-in-Charge (a) Cushioned seat TP

(b) Cushioned back

(c) PV Handle

(d) Bottom stand (PVC) with caster wheel

(e) Hydraulic pump steel

M/s Rajesh G Ramsinghani (BID ID -3190236)