Renovation of Quila Library in Ward No. 09 and 10 under MC Panipat.

Providing, fixing, jointing and testing uPVC mineral filled floor traps of self cleansing design with water seal not less than 50 mm., with or without vent, jointing with push fit rubber ring socket fittings complete, cutting chases / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position in case of suspended / open plumbing or setting the trap in 1:2:4 CC in case of concealed plumbing, etc. complete, as required. The trap shall be of following sizes: Temporary airtight PVC cover to be provided to prevent dirt entry

Providing and fixing uPVC pipe conforming to IS:4985 (10 kg/sq cm) including all fittings, This includes jointing of pipes and fittings with one step solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge and as per layout.

Providing and fixing floor drain fixed with cement mortar complete in all respect.

Providing and fixing 100 mm dia uPVC hopper approximately 300 mm long with maximum 3 inlets 32, 50 or 63 mm size fabricated from uPVC heavy duty pipes, sockets, fixed to UPVC trap with joint and set in cement concrete mix 1:2:4 complete as per standard drawing.

Supply of Grape Supporting Bars, 12 mm diameter, 2.4 m long fabricated from mild steel with U-bend at ends for wire holding, surface painted (2 coats red oxide plus 1 coat enamel), suitable for trellis grape farming system

Supply, fix and commission pedal-operated stainless steel dustbin (8-15 L capacity), grade 202/304, complete with removable inner bucket: suitable for public toilets/ washrooms...Robustt 8 L Pedal Dustbin or equivalent

Providing and fixing 25 mm dia motorize valve complete in all respect as per entire satisfaction of engineer-in-charget

Supplying, installing, testing and commissioning of Mono Block Centrifugal Pump with following specifications: |- Capacity: 1 m³/hr |- Head: [Specify head, e.g. 20 m] |- Motor: Single/Three Phase, 230V/415V, 50 Hz -Power Rating: [e.g. 0.5 HP or as required] NS - Material of Construction: Cast Iron body, SS/Brass impeller each 1 17825.00 17825 - Complete with base frame, foundation bolts, antivibration pads, coupling, NRV, gate valve, flexible hose, pressure gauge, etc. as required - Including necessary civil, mechanical and electrical connections and supports. - Make: [Approved make]

Providing and fixing uPVC pipe conforming to IS:4985 (10 kg/sq cm) including all fittings, This includes jointing of pipes and fittings with one step solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge and as per layout.

Providing and fixing uPVC pipe conforming to IS:4985 (10 kg/sq cm) including all fittings,

Providing and fixing of QUILA LIBRARY PANIPAT in Acrylic Letters with light of 24` Height with power Supply and Warrenty of 2 years with fittings complete with all respec

Providing and fixing 50mm Wooden Blinds with single cord operator complete with all respect

Providing and fixing of signages of toilet of size 300x450mm as per design complete in all respect up to the entire satisfaction of Engineer-incharge of the work.

Providing and fixing of 6mm Toughened glass comply with the requirement of BS EN 572 parts 1,2 and3 or ASTM C1036 assessed for optical and visual faults as described in BS EN 572-2. Spot faults to be no worsethan category C. There will be no linear /extended faults. Optical faults to be within the limits set in BS EN 572-2 of model no. ET 150 Toughened glass complete in all respect up to the entire satisfaction of Engineer-in-charge of the work

Providing and fixing of wooden polymer composite panel and WPC Louvers of size 160 x 2900 x 8.5mm as per design complete in all respect as per the entire satisfaction of engineer incharge

Providing and fixing customize Wisteria Feather Paper Wall covering in non-woven paper having width of 108 inches of 260 GSM as per design complete in all respect as per the entire satisfaction of engineer in-charge

Providing and fixing of floor vinyl strickring 3m pasting on floor complete in all respect as per the entire satisfaction of engineer incharge

Providing and fixing of grafity on wall as per design complete with all respect as per the direction of engineer-in-charge...(Make: ART Mahkama , Jakhar Art , Vriddhi Art Gallery )

Providing and fixing of SS Braille handrail signage of 304 grade 0.5mm thick with emboss dots of size 200x50mm complete in all respect up to the entire satisfaction of Engineer-in-charge of the work

Providing and fixing of a FRP Hand sculpture of 4` dia of tree covering complete in all respect as per the direction of engineer in charge .

Providing and installation of HP Laserjet AIO Printer 126NW Complete in all respect as per Satisfaction of Engineer-in-charge...(Make: HP, Brother, Canon)

Providing and installation of HP 379 DW Complete in all respect as per Satisfaction of Engineer-in-charge...(Make: HP, Brother, Canon)

Providing and planting of Hamelia patens (Harbeliya) shrub of height approximately 1 ’ -0” , healthy and well-grown, having dense foliage, planted in prepared pits of suitable size filled with good quality garden soil and manure, including watering , maintaince complete in all respects as directed by the Engineer-in-Charge

Supplying and planting of Washingtonia , approx. 3.6 m in overall height, nursery-grown, healthy, and well-formed specimen having straight trunk with well-developed crown and rootball including Excavation ,Refilling with good garden soil, well-rotted organic manure , complete in all respects as directed by the Engineer-inCharge

Supplying and planting of Cycas , approx. 0.9 m in overall height, nursery-grown, healthy, and well-formed specimen having straight trunk with well-developed crown and rootball including Excavation ,Refilling with good garden soil, well-rotted organic manure , complete in all respects as directed by the Engineer-in-Charge

Supplying and planting of Phoniex palm , approx. 1.5 m in overall height, nursery-grown, healthy, and well-formed specimen having straight trunk with well-developed crown and rootball including Excavation ,Refilling with good garden soil, well-rotted organic manure , complete in all respects as directed by the Engineer-inCharge

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required. (NS)…………… 30 Watt - 2x2 Recessed Mounted LIGHT (MAKE - Philips, Havells, WIPRO)

SITC of 9W Mono color Spike light, Protection Rating : IP66, complying to BIS standard `IS 10322 (Part 5/Sec 1): 2012` and having CE certification against standard `Low Voltage Directive and ProtectiveEquipment - EN 60598-1:2015`, and `Electromagnetic Compatibility Directive - EN 61547: 2009`, Mounting Structure : Spike for fixing the lights. Power consumption : 9W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots and fringing in color mixing applications. Power Input : AC110-230V, Surge Protection : Inbuilt surge protection 2KV- 4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, from NABL Acrediated laboratory. LED Makes should be CREE, Lumil LED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. (MAKE - Philips

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required.(NS)…………… 100-Watt FLOOD LIGHT Philips, Havells, WIPRO)

Design, manufacture supply, installation, testing and commissioning of the following extensible cubicle type indoor mounting, dead front, fully compartmentalised with hinged lockable detachable front and back openable, dust and vermin proof, floor mounting sheet steel clad switchboard fabricated out of 2 mm thick CRCA powder coated sheet steel suitable for use at 415 volts 3 phase 4 wire 50 cycle system and to withstand a symmetrical fault level as specified at 415 volts. Panels shall be fabricated in easily transportable sections, length, height, depth etc. to match with site condition. All incomer breaker and Bus Couplers shall b

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required.(NS)…………… 12-Watt Recessed LED (ROUND TYPE LED LIGHT) Philips, Havells, WIPRO

Supply, Installation, testing and Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R407c/R410a/EQUIVALENT Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50 ° C ambient temperature without tripping. The unit shall be suitable to work on 400V plus /-10%, 3Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. - The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5.

VRF/VRV 4 WAY CASSETTE INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless/corded remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 DegreeC DB and 19 DegreeCWB temperature.

VRF/VRV HI-WALL INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity VRV/VRF Highwall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil ection with DX copper coil, electronic expansion valve, outer cabinet, cordless remote control, drain pan, necessary accessories etc., suitable for operation on 230V ± 10%, 50Hz, single phase AC supply, complete as required. The unit shall have automatic force shutdown provision in caseof fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Supply, Installation, testing and Commissioning of following capacities of wall mounted propeller fan of ABS/metal and complete with suitable 1 phase Motor with gravity louver etc. and required for complete installation include Lifting, shifting, assemblling and positioning of the equipment comprising of the following and complete as per specification/drawings and as directed by Engineer In Charge. 400cfm

6.4 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

9.5 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

12.7 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.9 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia (OD) (Harddrawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

25.4 mm dia (OD) (Harddrawn) with tube thickness 1.2 mm with 19 mm thick insulation.

28.6 mm dia (OD) (Harddrawn) with tube thickness 1.2 mm with 19 mm thick insulation

31.8 mm dia (OD) (Harddrawn) with tube thickness 1.62 mm with 19 mm thick insulation

34.9 mm dia (OD) (Harddrawn) with tube thickness 1.62 mm with 19 mm thick insulation

Y-Joints (Suction plus Liquid

Header Joint

Supply and laying, testing and commissioning of following sizes of Copper conductor control cables through conduit on existing tray including fixing clamps and proper connections to equipments etc. complete as required. As per specification/ drawings and as directed by Engineer In 6.1 NS-19 2C x 1.5 sq.mm.

The overall size of Chair shall be Total height 840 plus /-3 mm, Over all chairir wwidth should be 535 plus / 5mm and Overall chair depth should be 535 plus /-5mm. Back Width 360mm at Top and 440mm at bottom, Seat Width 420 plus /-3 mm, Seat Depth 425 plus /-3 mm and Seat height 450mm plus /-5mm. Seat and back shellshould made by injuction moulding process with plastic material of PPGF20%. Seat and back shall be provided with cushion with fabir Upholstered. The Chair understructure should be provided with 12 mm thicknes

s MS rod loop legs with rod conforming to IS7887. Injuction moulded Polycarbonate Leg shoes shall assembled to understructure. seat assembled shall be with silicon bushes to ensure stratch free when chairs stached. Understructure shall powder coated upto 40 to 60microns.. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green current Guard ULvalid Gold dates. Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with

Double Sided Book Rack : The overall size of the book rack shall be 900 L X 700 D X 1950 (LDH)mm. Uprights shall be made up of - MS Pole 40 x 40 x 1.6 Tube having slot single side, size of 25 x 5mm rctangular slot to support the partition bracket having overall size of 300 x 99mm. Two U channel shall be welded with MS square pole size of 13 x 10 x 13 and have 1mm thick for support of back panel. Shelves should be made of MS powder coated metal 1.2mm, supported with hat shaped brackets size of 9 x 10 x 20 x 10 x 9mm and overall size of 36 x 10mm. Back Panel shall be made up of MS Powder coted metal 0.8mm. Top panel, Side Panel and Bottom Panle shall be made up of 18mm thick PLT. Skriting shall be provided of size of 900 x 40mm. Tolerance of plus /- 5mm to be considered for product sizes i.e Length, Depth and height and tolerance of 5% to be considered in pipe thickness and Pipe sizes.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.

PROPELLER FAN Supply, Installation, testing and Commissioning of following capacities of wall mounted propeller fan of ABS/metal and complete with suitable 1 phase Motor with gravity louver etc. and required for complete installation include Lifting, shifting, assembling and positioning of the equipment comprising of the following and complete as per specification/drawings and as directed by Engineer In Charge.100 CFM

PROPELLER FAN Supply, Installation, testing and Commissioning of following capacities of wall mounted propeller fan of ABS/metal and complete with suitable 1 phase Motor with gravity louver etc. and required for complete installation include Lifting, shifting, assembling and positioning of the equipment comprising of the following and complete as per specification/drawings and as directed by Engineer In Charge.250 CFM

IP Varifocal Dome camera: Design, Supply, installation, testing and commissioning of 4MP BULLET IP CAMERA.,minimum 1 year warranty Make: Hikvision / Bosch / Pelco / Honeywell / GVD

supply , Installation , Testing and commissioning of 8 Channel NVR (Network Vedio Recorder) Make: Hikvision / Bosch / Pelco / Honeywell / GVD

Supply, installation, testing and commissioning of 32` inches LED screen suitable for showing out puts from NVRs on a single screen (24x7) complete in all respect complete as required. Make: Hikvision / Bosch / Pelco / Honeywell / GVD

Supply, installation, testing and commissioning of 4 TB Survillance HDD for camera recording.(24*7 ) Make: Hikvision / Bosch / Pelco / Honeywell / GVD

Supply, installation, testing and commissioning of RJ 45 CONNECTOR Make: Hikvision / Bosch / Pelco / Honeywell / GVD

Supply, installation, testing and commissioning of Fiber patch cord 1 mtr. complete as required.

Supply, installation, testing and commissioning of Cat - 6 Patch cord 2 Mtr. complete as required.

SITC of 6U WALL mount with front glass door and side panels, 2 Fan with lock and key (load bearing capacity of 10Kgs), AC main Channel 4 points 6 Amp (PDU) with Mounting Hardware as per specification etc. all complete Approved Make: Valrack / Netrack / President

Supply, laying and termination of CAT6 cable in existing conduits/ raceway/ cable tray for both video and control.

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Renovation of Quila Library in Ward No. 09 and 10 under MC Panipat.