CERTAIN REPAIRS TO ROLLING SHUTTERS JOINERY FLOORING AND MISC WORKS IN OFFICERS ACCOMODATION AT OLD CANTT PATIALA

Amount

S&F in repairs 1.25mm thick steel rolling shutters, but gear operated type with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete : push pull or manual type including and over two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed by Engr-in-charge

M&L for repairing rolling shutters of any description including taking down and greasing, oiling, replacing defective parts such as hasp, staple, safety lever locks, ball bearings, gear box, hood cover etc and refixing the same complete all as specified and directed by Engr-in-charge

Demolition of cement concrete (un-reinforced) in any thickness (below or above ground level), complete all as specified and directed by Engr-in-Charge.

M&L machine pressed rubber moulded ISI marked precast cement concrete interlocking paver block 60mm th any shape and size and of with grey cement and pigment tiles confirming to IS-15658-2006 of M-35 grade complete all as specified and directed by Engr-in-charge

M&L machine pressed rubber moulded ISI marked precast cement concrete interlocking paver block 60mm th any shape and size and of with grey cement and no pigment tiles confirming to IS-15658-2006 of M-35 grade complete all as specified and directed by Engr-in-charge

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-in-charge

M&L for cement concrete D-2 1:4:8 (40 mm graded aggregate ) as in mass concrete, sub base etc complete all as specified and directed.

M&L cement concrete type B1 1:2:4 (20 mm graded stone aggregate) in roof kerbs, paddings or mud stops rounded or chamfered complete all as specified and directed.

M&L for providing and Laying Premium (1st) quality straight edge, ceramic tiles WA value between 3% to 6% , flexural strength greater than 22N/mm², scratch resistance on mohs scale greater than 4 and crazing resistance of 2 cycles in area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqm in floor, 6 to 8 mm thick in floors etc. in any shade and design/pattern of light & dark tiles etc as approved matching with wall tiles, set & jointed in neat cement slurry & pointed in matching colored polymer cement based grout to match over complete all as specified and directed by Engr-in-Charge.

M&L for Screed bed or bedding layer of mortar 20 mmthick in cement mortar 1:4 for laying floor finishes complete all as specified and directed by Engr-in-charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-charge

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes complete all as specified and directed.

Dismantling of asbetos/fibre cement corrugated/semi corrugated sheet in roof covering including ‘J’ or ‘L’hooks complete all as specified and directed by Engr-in-charge

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S &F Pre-painted galvalume zinc coating GI Based corrugated steel sheet of tile profile having TCT 0.45 mm thick, rib height 28 mm, 35 micron total paint coated thickness, min. G300 Mpa grade, weight not less than 4.9 kg/sq.m, pitch 200 mm with 16mm step depth, of colour as approved as in roof covering, including supply and fixing of ridge of plain sheet of same colour, material and manufacturer fixed with fasteneres/screws as recommended by manufacturer complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good to disturbed surfaces completeincluding reqd shape for hold fast block for new frame complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed by Engr-in-Charge.

M&L cement concrete 1:2:4 type B-1, using 20mm graded stone aggregate as in holdfast blocks/ filling in chowkats complete all as specified and directed by Engr-in-Charge.

M & L for Powder coated (Minimum thickness of powder coating 50 micron ) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

M & L for Aluminium window (Casement & sliding) and ventilator shutters with 50 micron powder coating double shutters made and to be fixed with EPDM gasket to render the glazing, air and water tight etc. and aluminium beeds in inner shutters complete fixed in all respect as specified & directed by Enginner-in-Charge. Note :- EPDM gasket shall be measured as supply only separately

M&L for fixed type frameless partition with door of size 1m x 2.1m made of 12 mm thick sand blasted toughened glass fixed to floors, walls and top support with SS 304 grade accessories / conncetors i.e single leg spider, ceiling / bottom to glass connecter, glass to glass connector, handle, doorset, floor spring, pivot etc, all the necessary fittings upto all height including scaffolding all complete all as specified and directed by Engr-in-Charge.

S&F 12mm thick high density fibre board pre-laminated on both sides (water proof) below & above middle/ lock rail in powder coated aluminium doors and to be fixed with and including EPDM gasket to render the glazing, air and watr tight etc aluminium beads 20mm size with and complete all as specified and directed by Engr-in - charge.

S&F factory made aluminium 50 micron powder coated grill, of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows complete all as specified and directed by Engr-in-Charge.

S & F for Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed by Engr-in-charge

S&F 4mm thick tinted glass for aluminium windows including EPDM gasket to render the glazing, air and water tight etc and power coated aluminium beeds 20 mm size complete all as specified and directed by Engr-in-charge

S&F stainless steel wire gauge 0.36 mm nominal dia of wire and average width of aperture 1.40mm to be fixed in Powder coated aluminium windows/ ventilators etc complete all as specified and directed by Engr-in-charge

S&F stainless steel (304 grade) finished butt hinges 100mm complete all as specified and directed.

S&F stainless steel (304 grade) finished butt hinges 75mm complete all as specified and directed.

S&F powder coated aluiminium tower bolt 100mm long complete all as specified and directed by Engr-in-charge.

S&F powder coated aluminium handles 150mm complete all as specified and directed by Engr-in-charge

S&F powder coated aluminium hook and eye of suitabel length adjustable to aluminium window shutters complete all as specified and directed by Engr-in-charge

S&F 4mm thick frosted glass fixed to aluminium ventilator including necessary EPDM gasket to render the galzing, air and water tight etc and powder coated aluminium beeds 20mm sized complete all as specified and directed by Engr-in-charge

Dismantling of boarding of any type/size as in CB/wardrobes or fixed in any position in hardware (if any) etc complete all as specified and directed by Engr-in-Charge.

S&F 18 mm thick with min density 600 Kg/cu.m LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed by Engr-in-Charge.

S&F 18 mm thick with min density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour fixed with ss screws ans solvent cement/ adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s instructions complete all as specified and directed by Engr-in-Charge.

S&F 12 mm thick LEAD FREE PVC Celuka ply fixed with ss screws and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed by Engr-in-Charge.

S&F 5 mm thick with min density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour and pasted with solvent cement/ adhesive on frame work of cup boards complete as per manufacturer’s instructions complete all as specified and directed by Engr-in-Charge.

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs, complete all as specified and directed by Engr-in-Charge.

S&F tower bolts 125mm long of stainless steel 304 finished/of outer plate metal matt finished complete all as specified and directed by Engr-in-Charge.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete all as specified and directed by Engr-in-Charge.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions complete all as specified and directed by Engr-in-Charge.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete all as specified and directed by Engr-in-Charge.

S & F continuous (Piano) hinges 30 mm , mild steel, bright finish or electrogalvanised complete all as specified and as directed

Taking down cement plaster on brick walls built in cement mortar incl raking out joints and concrete surfaces as in wall or ceiling etc incl hacking for key scrubbing down with water etc complete all as specified and directed

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches,pillars etc complete all as specified and directed by Engr-in-charge

M&L Brick work with sub class 'B', old size bricks, designation 100, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per item No above but except brick complete all as specified and directed by Engr-in-charge

M&L for cement plastering 10mm thick in cemet mortar 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Preparation of plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting priming paint complete all as specified and directed by Engr-in-Charge.

M&L for cement plastering 15mm thick in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces complete all as specified and directed by Engr-in-Charge. Note : WPC will be measured and paid separately.

Supply only integral liquid water proofing compound complete all as specified and directed by Engr-in-Charge.

Preparation of plastered surfaces of walls etc. and applying two coat of cement base paint over a coat of chalk whiting (as primer) complete all as specified and directed by Engr-in-Charge.

M&L for preparing new steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

M & L for precast cement concrete type B0 1:2:4 using 12.5mm gr aggr set in CM 1:4 louvers and jallies 25mm thk (measured solid) incl all mouldings complete all as specified and directed

Complete removal of existing treatment including washing rubbing down and stopping of painted surfaces and applying 1-2 mm thick texture painting (Top quality) on walls in any colour/shade/pattern/design including preperatory work for base by applying primer/putty coat by any authorised applicator complete all as specified and directed

M & L in replacement for 8 mm thick prelaminated wooden flooring laid over existing concrete surface by the manufacturer as approved by the GE in writing in a amnner and providing the items as specfied below:- (a) 125 micron polythene sheet (as vapour barrier) laid over existing concrete surface inclding taking all necessary steps to make the levelness and smoothness of existing concrete surface and achieve moisture free conditions. (b) 5 mm thick themocole sheet over polythene sheet. (c) 8 mm thick prelaminated wooden flooring.

M&L for rubber moulded coloured chequered tiles 30cm x 30cm x 22mm thick with grey cement and pigment, set jointed and pointed in neat cement slurry as in floor complete all as specified and directed by Engr-in-charge

M&L for repair to RCC ceiling, sunshades, Chajjas, Balconies, Columns, bands, beams, roof slab and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed by Engr-in-Charge. Note : The extra area of 300mm around the actual affected area will be checked and repaired and only repaired portion will be taken for measurement.

S & F Viterous china premium/1st quality urinal sensor type white colour, of size 310 X 305 X 620 mm including providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and including S&F of all accessries for fixing as recommended by manufacturer like 60 mm long brass secrews/fasteners/rag bolts etc, pointing urinal back in white cement: connecting for discharge pipe including necessary packing, union, including sensor type flushing, complete all as specified and directed.

Arneja Builders

SWAMI ENGINEERS

Nanotech Construction

AR CONSTRUCTIONS

KG BUILDERS

ANIL KUMAR AND CO

HARJIT CONTRACTS

FAVOURITE ENGINEERS