SPECIAL REAPIR TO OTHER RANK MARRIED ACCOMMADATION BUILDING NO P-96, P-99 AND P-101 AT VIVEK VIHAR AT SUNJUWAN MIL STN UNDER GE JAMMU

Amount

Taking down chowkats or frames with shutter w/o taking off shutter from the frame not exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 sqm but not exc 4 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving's n.exc 15 cm thickness (below or above ground level) and removing unserviceable material exc 100 mtr complete all as specified and as directed.

Demolition of brick masonry built in cement mortar including all quions, arches, pillars etc. complete all as specified and as directed.

Taking down cement plaster on wall , ceiling, chajja, conrnices etc of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc including necessary scaffolding and lifting arrangement upto three story height a complete all as specified and as directed.

Dismantling floors hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling of PVC, cast iron 100mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches. If required complete all as specified and as directed.

Demolition of cement concrete (Reinforced cement concrete) in ground floors and paving's n.exc 15 cm thickness (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Dismantling of PVC, cast iron 75 mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches. If required complete all as specified and as directed.

Taking down GI tubing of 15 mm dia and connection and incl cleaning for refixing or removal complete all as specified and as directed.

Taking down GI tubing of 20 mm dia and connection and incl cleaning for refixing or removal complete all as specified and as directed.

Dismantling/disconnecting/demolition of water storage tank of any type or description PVC exc 500 and n.exc 1000 Ltrs capacity complete all as specified and as directed.

M&L for brick work of old size sub class ‘B’ bricks straight or curved on plan exceeding 6mtr mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

All as per Ser No 14 here-in-before but except bricks complete all as specified and as directed.

S&F powder coated aluminium sliding window (three track) consisting of two shutter of glazed and one shutter of flyproof complete all as specified and as directed. Note :The item shall be included as following :- (a) Aluminium powder coated frame of section 100 x 44 mm x 1.5 mm with or without rebate. (b) Aluminium powder coated fwindow shutters of section 40 x 20 mm x 1.5 mm thick (Two shutter of glass and one shutter of wiremesh) incl self locking catch & roller etc). (c) 4.0 mm thick coloured or tinted glass glazing as in aluminium door/ window/ ventilator with aluminium hollow beading/ glazing clip (included with shutters) size 19mm x 17mm made out of 0.70mm thick hollow section weighing not less than 0.97 Kgs/RM including rubber gasket (d) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples.

S&F powder coated aluminium ventilator consisting of half portion fixed with 4mm frosted glass and another half portion louvers with mosquoto proofing and also provision of exaust fan complete all as specified and as directed. Note :The item shall be included as following :- (a) Aluminium powder coated frame of section 100 x 44 mm x 1.5 mm with or without rebate. (b) 4.0 mm thick coloured or tinted glass glazing as in aluminium door/ window/ ventilator with aluminium hollow beading/ glazing clip (included with shutters) size 19mm x 17mm made out of 0.70mm thick hollow section weighing not less than 0.97 Kgs/RM including rubber gasket (c) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples.

S&F Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3 mm thick flat iron projecting 10 cm on either side including one shop coat of red oxide primer complete all as specified and as directed. Note: PCC 1:3:6 type C-O as in back fill will be paid separately.

S&F Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3 mm thick flat iron projecting 10 cm on either side including one shop coat of red oxide primer complete all as specified and directed. Note: PCC 1:3:6 type C-O as in back fill will be paid separately.

M&L cement concrete 1:3:6 type C-O using 12.5mm graded stone aggregate as in backfill of pressed steel door frames complete all as specified and as directed.

S&F solid PVC door frame and for cupboards of size 50mm x 47mm made out of 5mm PVC sheet & edges will be painted to match with printed sheet, reinforced with MS square tube supplying and fixing in opening complete all as specified and as directed.

S&F 28mm to 30 mm thick (style) factory made soil PVC moulded door shutterwith wood free EPS with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supply and fixing in frame at site as per specifications and drawing shown in SSR complete all as specified and as directed.

S&F stailness steel door facoty made box type hollow section 0.80 mm thick size for vertical and top rail 100 mm x 35 mm size of middle rail 150 mm x35mm and bottom rail of size 200x35mm single rebated comprises wire gauged skelton shutter including 02 nos 150 mm handle, 200 mm tower bolts and 01 no 300 mm long sliding door bolts complete all as specified and as directed. Note : Wire gauge measured and paid separatly

S&F 30mm thick Flush shutters, soild core construction, with particle board core and plywood face panels, both faces are covered with decorative face veener with lipping/frame to match complete all as specified and as directed.

S&F for 35 mm thick 2nd class hard wood half glazed and Skelton shutters open rebated and prepared to receive glass/wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of member as per clause 8.20(a) of SSR part -I for door shutter complete all as specified and as directed.

M&L for pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60x40mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkhats including butt hinges 100 mm long piano hinges measured separatly complete all as specified and as directed.

M&L for 19 mm thick prelaminated MDF interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboard shutters/pelmet box and cupboard shelves including teak wood beading all around complete all as specified and as directed.

S&F kitchen cabinet & CBs shutter with frame and shelves made of solid uPVC foam profile with homogenous fine cellular structure having smooth outlet integal skin having 45mm width and 18mm thickness as vertical & horizontal stiles, joints are made and shall be fixed to walls using required size sheet metal acrew and solvent adhesive vertical and horizontal profile made of UPVC profile frame of size 35mmx17mm. The panel shall be filled with accucell polank profile of size250mm width and 6mm thick complete all as specified by manufacturer instruction complete all as specified and as directed.

S&F continious piano hinges MS bright finish or electrogalvanised width of flap 30mm when open complete all as specified and as directed.

S&F Magnet ball catches with 8mm dia steel ball and brass body and striking plate for cup board/cabinet shutters complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. Note : From work required for these item included in the unit rate of this item.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanized with staples including one coat of red oxide primer complete all as specified and as directed.

S&F Stainless steel butt hinges 100mm long medium weight cold rolled complete all as specified and as directed.

S&F 100 mm long hasp and staple, aluminium anodixed with bolt to hinge palte and fixed with screws complete all as specified and as directed.

S&F aluminium tower bolt of size 150 mm complete all as specified and as directed.

S&F aluminium handle of size 150 mm complete all as specified and as directed.

S&F aluminium handle of size 100 mm complete all as specified and as directed.

S&F 20 mm dia Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic balls crewed for iron pipe and fixed (min wt 210 gram), screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F Mild steel helical/ordinary rat tail rod pattern door spring 300 mm including roller and roller plate complete fixed with welding all as specified (ISI marked) complete all as specified and as directed.

S&F small fittings 2nd class hardwood such as brackets of any types latch and hings blocks shaped door and window stops and the like, not exc 200 cu cm each complete all as specified and as directed.

S&F Aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B-1 using 20 mm stone aggregated as in floor finished rough complete all as specified and as directed.

M&L Glazed ceramic coloured tiles 450x300x7 mm thick on vertical surface as in skirting,dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including 10 mm thick screed in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 6 to 8 mm thick (Square/rectangulament) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors over 10mm thick tile adhesive and provided 4mm spacer space gap to filled with approved epoxy grout complete and jointed in epoxy grout with pigment to match the tiles complete all the specified and as directed.

M&L for non skid ceramic coloured tiles 6 to 8 mm thick (Square/rectangulament) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors over 10mm thick tile adhesive and provided 4mm spacer space gap to filled with approved epoxy grout complete and jointed in epoxy grout with pigment to match the tiles complete all the specified and as directed.

M&L for premium quality light shade Vitrified tiles in floor 8 to 10mm thick area of each tile n. exc 0.36 sqm set and jointed inj neat cement slurry and pointed in white or coloured to match over and including10mm thick tiles adhesive and jointed and painted epoxy grout complete all as specified and as directed.

M&L for Premium quality light shade Vitrified tiles 8 to 10mm thick as in vertical surface such as skirting/dados etc as approved size over and including 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

Demolition of stone slabs any description or thickness in floors laid , bedded and pinnedincement mortar complete all as specified and as directed.

M&L Granite 14 to 18mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed in CM 1:4 complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick in one piece as in treads laid over cement screed base 20mm thick in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and mirror polishing complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick laid over cement screed base 20mm thick in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and mirror polishing complete all as specified and as directed.

M&L for machine cut kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over 10mm thick backing coat in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing complete all as specified and as directed.

Rounding to edges of stone slabs Granite, Kota etc one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

M&L for rendering 15 mm thick cement plaster 1:4 on fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement including necessary scaffolding and kifting arrangement upto three storey height complete all as specified and as directed.

M&L for rendering 10 mm thick cement plaster 1:6 on other than fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick cement plaster 1:3 on fair faces of concrete surfaces as in ceiling, chajja, shelves etc. finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick cement plaster 1:3 on other than fair faces of concrete surfaces as on facia of roof slab, chajja, shelves etc. finished even and smooth without using extra cement (incl all necessary scaffolding, lifting arrangment for three story building on external surfaces) complete all as specified and as directed.

S&F PVC (SWR) P trap 110/110 mm bore complete all as specified and as directed.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and as directed.

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and as directed.

S&F PVC SWR bends of 110 mm bore complete all as specified and as directed.

S&F PVC SWR bends of 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) junction double (double T) equal or unequal provided with access door of 110 mm dia complete all as specified and as directed.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) reducer of 110 mm dia complete all as specified and as directed.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) WC connector with lip ring 110 mm complete all as specified and as directed.

S & F vitreous china Water closet pedestal pattern with sheet cover white and flushing pipe 32mm dia for low level flushing cistern (excluding fixing bolts and flushing cistern) including Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F PVC low level flushing cistern 10 Ltr capacity white with inlet ball value, float valve and handle inc brackets, PVC flush pipe complete all as specified and as directed.

S&F PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipes of 15 mm bore complete all as specified and as directed.

S & F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

S&F in repairs pillar taps 15 mm dia, cast copper alloy, with capstan heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed suitable for 15 mm bore complete all as specified and as directed.

S&F tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodised, fixed with rawl plugs complete all as specified and as directed.

S&F Vitreous China wash basin, white, flat back, size 580x450 mm including 32 mm dia PVC waste pipe, CP brass waste coupling 32 mm dia, pair of MS brackets or MS fastener/bolts for fixing arrangements and 450 mm long PVC connection with PVC nut and washer complete all as specified and as directed.

S&F in repair Bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and as directed.

S&F in repair stop valve/angle valve cast copper chromium plated screwed down high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete all as specified and as directed.

S&F in repair stop valve cast copper chromium plated concealed type screwed down high pressure with capstan head suitable for 15 mm bore complete all as specified and as directed.

S&F stainless steel gratings of outer frame dia 150 mm openable type PTMT incl all necessary fitting such as hinges including embedding in tiles with white cement complete all as specified and as directed.

S&F S/S gratings of 125 mm with waster holes of PTMT (minimumweight of 40 gms) complete all as specified and as directed.

S&F 15 mm bore CP brass centre hole basin mixture quarter turn with U shape round casted spout with 450mm long braided hoses fixed to GI pipe complete all as specified and as directed.

S&F Brass Chromium plated hot & cold water wall mixer 2 in1 system wall unit with over head shower arrangement with hot and cold valves cast copper alloy heavy duty screwed down for iron pipe and fixed complete all as specified and as directed.

S&F fin repair fancy type drapery curatin rod of stainless 25mm dia and side capes fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specfied and as directed.

S&F 15 mm dia galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 20 mm dia galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Fixing only 15 mm dia old galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and as directed.

Fixing only 20 mm dia old galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and as directed.

Cutting chases for concealed water tubing or concealed conduit & making good in Cement Mortar 1:3 of grith exc 10 cm and not exc 20 cm in brick wall complete all as specified and as directed.

M&L 75 mm thick PCC 1:3:6 type C-2 (40mm graded aggregate) as in plinth protection laid to an outward slope of not less than 1:12, cast in panels not exceeding 2.0 sqm areas with 6 mm wide joints. The joint shall be filled with mastic filling and 10 mm wide joints between the walls and plinth protection shall be filled with mastic filling and finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

S&F rotational moulded polythylene water storage tank with plastic lid cover, triple layered, cylindrical verticl with closed top hoisted and fixed in position of capacity 500 Ltr incl making connections complete all as specified and as directed.

Ditto all as per Srl item No 92 here in before but capacity of tank 1000 Litres complete all as specified and as directed.

S&F in repair gate valve 20 mm dia cast copper alloy, secrewed down high pressure with crutch or butterfly handle secrewed both ends for iron pipe and fixed complete all as specified and as directed.

M & L for applying one coat of synthetic enamel paint tint over old painted steel surfaces over 10 cm in width or girth including preparation of old surfaces of steel complete all as specified and as directed.

M&L for preparation of old wood or wood based surface and applying two coats of synthetic enamel paint complete all as specified and as directed.

Material and labour for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of internal wall/ ceiling to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by Berger Bison Putty / crack fill paste of Berger Paints or equivalent make and make good smoothen surface by sand paper and applying two coats of premium acrylic smooth interior emulsion of approved colour with silicon additive & Color stay Technology , Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed.Allow 6-8 hrs to dry the surface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Note :-(a) Work shall be done as per MoU between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed (b) The contractor shall upload MoU between tenderer and manufacturer of paints and their authorized applicator after conclude of tender and before place of Work Order Documents as mentioned in NIT.(c) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE.

Material and labour for preparation of newly plastered surface and applying two coat of premium acrylic smooth interior emulsion on wall and ceiling of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based interior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick interior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airlessspray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed Make: Berger/ Nerolac Paints /Asian Paint. Note :-(a) Work shall be done as per MoU between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed (b) The contractor shall upload MoU between tenderer and manufacturer of paints and their authorized applicator after conclude of tender and before place of Work Order Documents as mentioned in NIT.(c) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE.

Material and labour for preparation of newly plastered surface and applying two coat of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airlessspray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Note :-(a) Work shall be done as per MoU between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed (b) The contractor shall upload MoU between tenderer and manufacturer of paints and their authorized applicator after conclude of tender and before place of Work Order Documents as mentioned in NIT.(c) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE.

S&F Stainless steel kitchen sink made of stainless steel of 1 mm thick sheet including plugs, washers and pvc waste pipe of 40 mm dia. Fixing with complete on appropiate size of cantilever brackets of MS angle or GI pipe 15 mm dia with proper arrangment to hold and fitting of sink complete all as specified and directed at site and connecting union to pipe. The overall size of sink 495mm x 420mm and bowl size 410mm x 430mm x 160mm complete all as specified and as directed.

S&F Stainless steel grade 430, glossy finish, wall hanging plate rack inclusive of spoon hanger, made out of 1mm thick sheet of size 750 x 600 x 250 mm having partition as per sample kept in AGE B/R office and fixed with steel fasteners or steel screwed complete all as specified and as directed.

Glass fibre reinforced modified cementitious coating system before the final coat of (or equivalent) in Sunken treatemen. Base coat : (or equivalent), Consumption base coat : 0.3 Kg/Sqm, Reinforcement : Glass fiber, Second and Third coat :(or equivalent), Consumption top coat: 3 Kg/Sqm, System requirements : density: 2.00 Kg/Ltr, Compressive strength : 0.5 N/Sqmm. (i) Wall penetration through the RCC slab must be sealed using Berger HS Repir (or equivalent). (ii) Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto 1.5 Mtr. (iii) All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus(or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry, including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc

M&L cement concrete type E-2 1:5:10 (40 mm graded aggregate) as in sunken portion complete all as specified to receive floor toping as specified after carrying out the required tests of water proofing complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

One component liquid ,solvent free ,cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years Warranty. ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties. (i) UV resistant, prevent yellowing and weathering. (ii) Highly elastic upto 350% and crack bridging. (iii) Excellent adhesion on porous and non-porous substrates. (iv) Tensile Strength >10 N/Sqmm with GeoTextile fleece. (v) Solar Reflective Index (SRI) more then 109-111 ASTM E1980-11. System : First coat : Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent), Coverage : 0.2Kg/Sqm (with 50% dilution of water), Reinforcement: Geotextile 40 gsm, Second coat:Home sheild roofkoat (or equivalent), Consumption: 0.5 Kg/Sqm, Third coat: HS PU roofkoat (or equivalent), Consumption : 0.8 Kg/Sqm. System buildup -1.5Kg/Sqm with geotextile of 40gsm

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for angle iron work fixed indepently without connecting plates etc (cut to ordinery length ) such cooller stand etc of FE 410 -W (E-250 Grade) Quality A complete all as specified and as directed.

Taking down/out loose & damaged concrete/cement plaster from soffits of ceilings, floor/roof slabs, vertical surfaces of columns, beams etc., including exposing and removing rust fron the reinforcement by rubbing with wire brush and removal of debris to a distance n. exc. 100 mtr and depositing where complete all as specified and as directed.

M&L for cleaning existing reinforcement bars with wire brush/rotary wire brush making the surface free from cement skin, loose particle, dirt etc and applying rust remover (Rustoff 100 of Sika/ '8832GM' pidilite or equivelent of Fosroc/ Dr Fixit) on the rebars and removing the loose rust particles after minimum 24 hours by wire brush, all as per manufacture's instructions, complete all as specified and as directed.

M&L for cement based polymer modified anti corrosive rebar coating system ('Sika Top Armatec-108 " of Sika or equivalent of Dr. Fixit/ Fosroc) to existing reinforcement all as per manufacture 's instructions, complete all as specified and as directed. Note: Mode of measurment shall be affected surface area of column, beam, slab etc.

M&L for one layer of 20 mm thick concrete (comprises composition 1:2:1 plain cement concrete i.e. One part of cement (43 Gde OPC), two part of fine aggregate and one part of 10 mm and down size trap stone aggregate) mixed with 'Sprayset SL' of Fosroc( Equivalent to Sika / Dr Fixit) 2 to 2.5% by weight of cement and 12.5 to 16.5 liter of water mixed as per manufacture's instuctions and guniting by pressure nozzle with a delivery capacity of 2.5 Kg per sqm over column , beam, roof , slab, etc complete all as specified and as directed.

S&F hard drawn steel wire fabric, weight not exc 4 Kg per sqm , cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9 mm in dia, supplied and fixed in reinforcement, complete all as specified and as directed.

M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) cleaning nipple one by one commencing from the top to bottom in case of column and one by one in alternate direction incase of wall using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed. (viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Sika Injection -201IN Note : pressure shall be in the range of 1-2 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardener shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket , power , AC Point ) complete, including fittings such as switches,sockets, ceiling roses,bell push,lamp holder, pendants, regulators, sockets,call bell , any type switch board etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking Down carefully UNSV MCB /TPN DBs of any typ/Size with MCBs/TPNs and disconnected and making good disturbed surfaces complete all as specified and as directed.

M&L in replacment for Sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cables of 6 Sqmm 2 Single Core for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, coper conductor FRLS , drawn through concealed rigid PVC Concealed conduit fixed in wall complete all as specified and as directed. Note : 1) Two runs of cable for phase/ neutral and one run of cable for for earth will be measured and as one unit length.2) Wiring shall be done in proper colour coding.3)Rates are inclusive of cutting / chasis and making good to disturbed surfaces with suitable PCC works.

M&L for point wiring for one light/fan point controlled by one 5 Amp modular switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into concealed PVC rigid conduit including supply & fixing of new Modular Steel terminal boxes of required size along with modular white cover plate with frame of suitable size for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Note : (a) wiring shall be done by using proper colour coding incl making the disturb surface good. (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge. (d) The rates are inclusive of cutting / Chasis with suitable PCC works and making good to disturbed surfaces .

All as per item No 115 above but 5 Amp socket outlet on same board ISI marked complete all as specified and as directed.

All as per Item No 115 here in above but for one 5 pin 5 Amp socket outlet on Independent board with cables 1.5 sqmm size complete all as specified and as directed.

All as per item No 115 above but One bell point controlled by one push button on the same board with other switches or independent board complete complete all as specified and as directed.

All as per Item No 115 here in above but for multi 5 Pin 15 Amp Switch Socket Outlet with 2.5 Sqmm Copper conductor multistranded cable , PVC insulated (unsheathed) FRLS drawn into concealed PVC rigid conduit including continuous earth wire of size 2.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) cable complete all as specified and as directed.

All as per Item No 115 here in above but for one light point controlled by 2 way swiitches with cables 1.5 sqmm size complete all as specified and as directed.

S&F Modular socket 6A- 5 Pin combined , 2 module , 240 volts ISI marked complete all as specified and as directed.

S&F Modular switch 1 way 6A, 1 module , 240 volts ISI marked complete all as specified and as directed.

S&F for modular switch 1 module 6A, 2 way, 240 volts ISI marked complete all as specified and as directed.

S&F for modular bell push 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

S&F for ceiling rose, 3 Pin/PVC/polycarbonate isolated body ISI marked complete all as specified and as directed.

S&F for modular switch 1 way 16A, 1 module, 240 volts ISI marked complete all as specified and as directed.

S&F for modular socket 6A/16A-6 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

S&F for Call bell ding dong AC 230 volts, single pole ISI marked complete all as specified and as directed.

M&L Lamp Holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and as directed.

M&L for self ballast LED retrofit lamp with PVC body and PC diffuser 9 Watt 230 Volt 6500K complete all as specified and as directed.

S&F LED Light fitting , 1x 20W, 220V,AC decrative box type complete With LED tube rod 20 walts driver, holder and power factor >0.90 , 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F for Vertical distribution board (V-TP&N) 4 way double door suitable for MCCB TP 125 amp 16 KA , 3 pole as incomer, it should be IP 43 protected with copper busbars, neutral links, earthing bar complete all as specified and as directed.

M&L for distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed. Note:- Distribution board and MCBs should be same make.

Supply and fixing for SPN 40 to 63 amp rating 240v, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

S&F for 240V, 10 KA 'B' curve miniature circuit breaker (MCB)) of single pole and current carrying capacity 6 to 32 AMP complete with connection testing and commisioning complete all as specified and as directed.

M&L in replacement of earthing complete with galvanished mild steel earth plate electrode of size 600x600x6mm thick burried directly in groubnd earth (in vertical) earth pit not less than 2.25 mtr deep below ground level connected to galvanised iron or earth lead wire 4mm dia (8SWG) by means of nut, bolt, check nuts and washer of galvanisesd iron including PCC pit ibn PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with suitable handle made of round bar, including necessary excavation and erth work in any type of soil, 20mmdia medium grade galvanised steel tube flor watering with one end fixed with iron funnel and wire mash 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection ,common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR part-1 and testing on completion complete all as specified and as directed.

S&F in replacement for LED light fitting 10W bulk head luminaires including LED light driver holder complete all as specified and as directed.

Supply and fixing in replacement LED street light fitting 35 Walt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP-65/66 protection complete all as specified and as directed.

Supply and fixing for MCCB, TP, 415 Volts, 16 KA , 125 Amps , complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing modular fan step regulator, 100W-2 module 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement Ceiling fans, BLDC motor tech complete with blades, down rods, hanging hooks and accessories, 230 V, 1200 mm sweep, suitable for working on fan regulator, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). complete with fixing arrangement complete all as specified and as directed.

Supply and fix in replacement of exhaust fan, steel body, AC single phase 230V ,300mm sweep with blades, frame and making hole of suitable shape and size for 300 mm sweep including brick work, Plastering and making good to disturbed surfaces complete all as specified and as directed. Note- Contractor will depost old unsv Exhaust in MES yard for further course of action .

M/S VED PAUL MAHAJAN (BID ID -3518854)