ADDITION, ALTERATION TO VRMT (BLDG NO. P-13), ADDITION, ALTERATION AND SPECIAL REPAIRS TO SHOP FLOOR AND OFFICE SPACES YAS DEPT (BLDG NO. P-08), WINDOW GRILLS IN INDUSTRIAL GAS STORAGE (BLDG NO. P-15) AND PROVISION OF STORAGE SHED FOR CHEMICAL DRUMS

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M & L for vitrified ceramic tiles 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for vitrified ceramic tiles 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 Sqm, as in dado/ skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick bedding layer in CM 1:4 complete all as specified and directed.

M & L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 Sqm and not exc 0.38 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Description all as per item No 4.00 above but skirting over 10 mm thick rendering in CM 1:4 complete all as specified.

Taking down PVC chowkhats frames exc 1.5 Sqm but not exc 4.0 Sqm with shutter (without taking off shutters from the frames) all as specified and directed.

M & L for powder coated aluminium frames for doors, windows, ventilators with one or more rebates including jointing cleats, glazing clips, rubber neoprene packing for fixing etc complete all as specified and directed.

M & L for powder coated aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, aluminium snap beading screws etc. complete all as specified and directed.

S & F aluminium body, door closer, hydraulically regulated designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

S & F prelaminated particle board 12 mm thick interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination as in kitchen cabinets/ shutters fixed with screws in aluminium frame work all as specified & directed.

S & F mortice locks brass vertical type size 100 mm, 4 levers brass chromium plated with keys in duplicate all as specified and directed.

S & F aluminium powder coated barrel tower bolts of extruded section 200 mm long all as specified and directed.

S & F butt hinges 125 mm size, medium weight, extruded powder coated aluminium alloy with galvanized mild steel hinge pin anodized type C-21 complete all as specified and directed.

S & F extruded powder coated aluminium handles, fabricated type, 150 mm size complete all as specified and directed.

M & L for preparation of old painted plastered surface of walls of any description including cornices and applying one coat of acrylic emulsion exterior grade, weather proof antifungal paint complete all as specified and directed.

M & L for two coats of distemper oil emulsion including preparation of old plastered surfaces of ceiling all as specified and directed.

M & L for two coats of distemper oil emulsion including preparation of old surfaces of walls all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M & L for brushing neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified and directed.

M & L cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) in bed plates including necessary formwork complete all as specified and directed.

M & L for plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation & filling in mass concrete complete all as specified and directed.

M & L for 40 mm thick wearproof topping (by incorporating an approved metallic floor hardner), laid on concrete floors and pavings. Metallic floor hardener and cement shall be thoroughly mixed to an even colour in dry state in the proportion recommended by the manufacturer. This mixture shall be mixed with crushed granite/ basalt/ trap as indicated (6 mm and down) in the proportion 1:2 by volume. Requisite amount of water shall then be added to form a workable mixture and finished even and smooth complete all as specified and directed. NOTE: Metallic hardner shall be measured and paid separately.

M & L for metallic floor hardner of approved quality consisting of uniformly graded metal particles, free from non-ferrous metal particles, oil, grease sand, soluble alkaline compounds for increasing abrasion resistance and shall be Ironite, Hardonate, Ferronite or other equal and approved metallic floor harderner complete all as specified and directed.

S & F 3 mm thick glass dividing strips of width 22 mm inserted in position and conforming to design complete all as specified and directed.

M & L for preparation of old decorated surfaces including washing, rubbing down and stopping of distempered surfaces and applying one coat of distemper oil emulsion on walls complete all as specified and directed.

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Removing excavated material exc 250 m but not exc 500 m and deposited where directed at a level not exc 1.5 m above the base as in soil complete all as specified and directed.

Returning, filling in soil including spreading, levelling, watering and well ramming in layers not exc. 25 cm all as specified and directed.

M & L for moorum/ red bajri filling in floors or pavings, laid in layers not exc 15 cm thick spread, levelled and rammed including watering complete all as specified and directed.

M & L for hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for providing cement concrete, 75 mm thick, type B-1, 1:2:4 (using 20 mm graded aggregate) as in sub base or sub floor etc complete all as specified and directed.

M & L for providing precast cement concrete solid building blocks masonry exc 10 cm width, type C-5,1:3:6 (using 20 mm graded aggregate) set in cement mortar 1:6 complete all as specified and directed.

M & L for rendering 15 mm thick plaster in CM 1:4 in two coats (10 mm thick backing coat + 5 mm thick finishing coat) on concrete surfaces of walls finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls of any description including and applying two coats of weather proof exterior emulsion paint and over a coat of primer complete all as specified and directed.

M & L for cement concrete (1:3:6) type C-1, using 20 mm graded stone aggregate as in coping etc. including necessary formwork including weathering, slightly rounded or chamfered angles and throating all as specified and directed.

M & L for providing 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded aggregate as in plinth protection and finishing the concrete surface even and smooth without using extra cement complete all as specified and directed.

M & L for MS structural framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M & L for steel work in tubular trusses, purlins, rafter etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

M & L for pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of new steel surfaces of any description exc 10 cm in width or girth complete all as specified and directed.

S & F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls as rain water pipes all as specified and directed.

S & F 110 mm dia PVC (SWR) bends all as specified and directed.

Dismantling wrought iron or mild steel work of any description all as specified and directed.

M & L for cutting holes in brick walls exc half brick but not exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M & L for MS structural framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 410-W (Grade E-250) quality A complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc. all as specified and directed.

Taking down unserviceable DB TPN/ SPN any type, any capacity and making good disturbed surfaces of walls complete all as specified and directed.

M & L for surface point wiring 1100 Volts grade 1.5 Sqmm PVC insulated FRLS unsheathed cable with multistranded copper conductor conforming to IS:694:1990 with ISI marking in and including PVC casing & capping medium grade with all accessories in wall/ ceiling/ floor/ roof etc, sunk pressed steel or cast iron terminal boxes with 3 mm thick plastic laminated sheet top cover including 1.5 Sqmm PVC insulated FRLS unsheathed 1100 Volts multistranded copper conductor conforming to IS:694:1990 with ISI marking as continuous earth wire connected to common earth dolly all as specified and directed for the following:-

(a) One light/fan point controlled by one switch.

(b) One 3 pin socket outlet 5 Amp on independent board.

(c) One 3 pin socket outlet 5 Amp on same board.

M & L for point wiring complete for one socket outlet 15 Amps on an independent board with FRLS, PVC insulated and unsheathed cable 2.5 Sqmm (nominal area) multistranded copper conductor single core conforming to IS 694:1990 with ISI marking including PVC casing & capping pressed steel terminal boxes not less than 2 mm thick of required size (factory made) including painting terminal boxes inside and outside with two coats of synthetic enamel paint over a coat of red oxide primer and with top cover 3 mm thick of plastic laminated sheets of required colour, complete with all accessories and all as specified including FRLS PVC insulated and unsheathed cable 2.5 Sqmm (nominal area) multistranded copper conductor single core conforming to IS:694:1990 with ISI marking of green colour as earth wire to common earth and connected to earth dolly drawn in same concealed conduit complete and controlled by one 15 Amp switch complete all as specified and directed by Engr-in-Charge.

M & L for point wiring complete for one socket outlet 15 Amps on an independent board with FRLS, PVC insulated and unsheathed cable 4.0 Sqmm (nominal area) multistranded copper conductor single core conforming to IS:694:1990 with ISI marking including PVC casing & capping pressed steel terminal boxes not less than 2 mm thick of required size (factory made) including painting terminal boxes inside and outside with two coats of synthetic enamel paint over a coat of red oxide primer and with top cover 3 mm thick of plastic laminated sheets of required colour, complete with all accessories and all as specified including FRLS PVC insulated and unsheathed cable 4.0 Sqmm (nominal area) multistranded copper conductor single core conforming to IS:694:1990 with ISI marking of green colour as earth wire to common earth and connected to earth dolly drawn in same concealed conduit complete and controlled by one 15 Amp switch complete all as specified and directed by Engr-in-Charge.

S & F in repairs ceiling fan regulator electronic five step type 230 Volts single phase complete all as specified and directed. MAKE: Havells/Anchor/Cona or equivalent as mentioned in list of makes.

Taking down submain wiring cable of any size/ type alongwith earth wire from the existing concealed/ surface conduit and offering credit complete all as specified and directed. NOTE: Any runs of cable and earth wire will be measured as one unit length.

M & L for sub main wiring with 4 runs of 10 Sqmm single core copper conductor PVC insulated cable and 2 runs of 10 Sqmm single core copper conductor insulated cable as earthing lead, drawn through existing PVC conduit complete all as specified and directed by Engr-in-Charge. NOTE: 4 runs of cable 10 Sqmm and 2 runs of cable 10 Sqmm together will be measured and paid as one unit length.

S & F in repairs switch piano 5 Amps one way flush type, ISI marked complete all as specified and directed. MAKE: Havells/Anchor/Cona or equivalent as mentioned in list of makes.

S & F in repairs socket 5 Amps, ISI marked complete all as specified and directed.

S & F in repairs switch socket combination outlet 3/5 pin, 5/16 Amps flush type multipurpose, ISI marked complete all as specified and directed.

S & F in repairs LED batten suitable ultra slim aluminium square profile LED lighting fixture, 24 W, 230 Volts, complete with all connected accessories including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. MAKE: Havells Cat Part No. LHEXACP7INS024 or equivalent in Bajaj/Philips/ Wipro/ C&S/ Shakti

S & F MCB DB SPN, 12 way, double door powder coated sheet steel enclosure for surface mounting fitted with 200 Amps bus bar and din channel complete all as specified and directed. MAKE: Havells/Indo Asian/Legrand or equivalent as mentioned in list of makes.

S & F in repairs MCB SPN, 40 Amps, ''C'' series 230 Volts, single phase, 10 KA breaking capacity complete all as specified and directed. MAKE: Havells/Indo Asian/Legrand or equivalent as mentioned in list of makes.

S & F in repairs MCB SP, 6 to 30 Amps, ''C'' series 230 Volts, single phase, 10 KA breaking capacity complete all as specified and directed. MAKE: Havells/Indo Asian/Legrand or equivalent as mentioned in list of makes.

M & L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of earth plate not less than 1.5 m below normal ground level connected to galvanized earth lead 4 mm dia by means of bolts, nuts washers and check nuts of steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 15 mm bore for protection of GI wire from each electrode to and including the earth test point of GI/ steel of size 75 x 75 x 25 mm, supplying and laying charcoal dust, common salt, PCC 1:2:4 type B-1 chamber and MS angle iron frame 40 x 40 x 3 mm and RCC cover 40 mm thick (1:2:4) typr B-1 using 20 mm graded stone aggregate reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia, GI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in Plate No. 3 of SSR Part I, 2009 and connected to earth test point including testing complete all as specified and as directed by Engr-in-Charge.

KVL CONSTRUCTION

K.G.SHANKER

Bidder Name

M/S G.N.POWAR

K.G.SHANKER

KVL CONSTRUCTION