PROVN OF PATH AND

Amount

Surface Excavation n exc 30 cm deep and averaging 15 cm deep and getting out Hard / dense soil complete all as specified and directed by Engineer-In-Charge.

M&L for 75 mm thick PCC type D-2, 1:4:8 (40 mm graded aggregate) as in sub base complete all as specified and directed by Engineer-In-Charge.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for 60mm thick, M-30 Grade Machine pressed precast concrete interlocking paver block any shape and size casted in plastic moulds and compated on vibratory table confirming to IS 15658-2006 with grey cement and pigment complete all as specified and directed.

M&L for Providing, cement concrete (1:2:4) (20mm graded stone agg) in roof/side kerbs or mud stops, rounded or chamfered on edges making good disturbed surface of ground complete all as specified and directed by Engineer-In-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L for cement concrete 1:3:6 typeC2 (40mm graded stone aggregate) in foundations, filling and mass concrete. complete all as specified and directed by Engineer-In-Charge.

S&F hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-In-Charge.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc. complete all as specified and directed by Engineer-In-Charge.

Supply only Chain link MS galvanised fencing, any size or type weighting complete all as specified and directed by Engineer-In-Charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by Engineer-In-Charge.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long dia of shank 5 to 10 mm complete all as specified and directed by Engineer-In-Charge.

S&F for mild steel round bars, 12 mm dia and over cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality conforming to Fe-410W Gde E-250 complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-In-Charge.

S&F precast factory made polycrete (SFRC) medium duty main hole / Drain covers 80mm thick rectangle in shape upto 0.60 sqm area for main hole/drain with at least 5cm bearing each side complete all as specified and directed by Engineer-In-Charge.

shiv shanker enterprises

Tsmalik

J D ENTERPRISES