Expansion of Civil Enclave at Gwalior Airport. SH Furnishing of VIP Lounges of New Terminal Building at RVST Gwalior (2nd Call)

Amount

SH A: Civil Works Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm/230mm/300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately)

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame wok with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: (part 3) : 1996 (Board with BIS certification marks)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Melamine polishing on wood work (one or more coat).

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) On one side only

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250x10mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.On Srone Work/Marble/Granite

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and laying machine cut, mirror polished Marble stone flooring,in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red, Dark Emperadore or Grey etc.

Screeding for Carpet Flooring 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Wooden Flooring 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete in Herringbone pattern with : Second class teak wood

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Wall painting with acrylic plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Texture Paint (Beige/OIKOS or of approved code by EIC) Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints Size of Tile 600x600 mm

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern (if required with marble stone slab pieces of different shapes, sizes & texture but of even thickness) on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore or any color as approved by EIC.

Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 200 mm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart (frames to be paid separately), including fixing 50x12 mm beading complete with : Second class teak wood

Providing and Fixing Rack and pinion Door closer of Dorma /Hafele / ASSA ABLOY of width upto 1100 mm, as per EN1154 or approved equivalent make, SS Grade 304 all complete as per ER

Providing and fixing Dead Lock with 60 mm EPC of Dorma/ Hafele / ASSA ABLOY or approved equivalent, SS Grade 304 all complete as per ER

Providing and fixing Pull Handle of Dorma / Hafele / ASSA ABLOY. Length =300mm, 22mm dia, -, SS Grade 316 all complete as per ER

Providing and fixing Floor stopper half dome 45 mm dia of Dorma / Hafele /ASSA ABLOY or approved equivalent , SS Grade 316 all complete as per ER

FRAMELESS DOUBLE LEAF SWING GLASS DOOR Supply & Installation of glass doors Providing, supplying and fixing of Frameless Double Leaf Swing Glass Door make in glazing using 12mm thick toughened glass with die cast patch fitting with stainless steel cover including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items as detailed, complete in all respects as per detailed drawings, manufacturers specifications and direction of Engineer in charge. Double Leaf Door with Hardware’s as specified:- Swing Glass Door which includes One nos of Top Pivot, Bottom Patch, Top Patch, Floor Lock, Strike Plate , Floor Spring, or any patch as per site requirement with pair of SS Pull Handle 25 mm dia x 450 mm long and other accessories for self closing feature Double door with fan light and side panels consists of the following: a) 2 Set Glass door over/side panel fitting, with pivot and satin SS covers. b) 2 Set Top patch fitting with pivot bearing location, with satin SS covers. c) 2 Set Bottom patch fitting with pivot bearing for floor spring, with satin SS covers. d) 2 Set Floors lock with strike plate and Euro Profile cylinder. e) 2 Set Floor Spring f) 2 Set Back to Back SS Pull Handle 450mm x 22mm diameter.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size, Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size, Size of Tile 600 x 600 mm

FLOCKED CARPET FLOORING i) "Providing & Fixing of Flocked textile floor of Nylon 6.6 face fiber or equivalentof approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, anti-microbial treatment, with resilient waterproof backing, anti allergic which is certified by British allergy foundation. The carpet should have permanent static contro. The work should be carried out by the authorized installer of the Company in India. Carpet should be laid on zero leveled surface. Carpet should be stick with SR 998 on the floor.

TOILET CUBICLES Providing and fixing Toilet cubical (cubical of max size (1550 mm*2100 mm or as per drawing ) of 'Greenlam', 'Merino' or 'Debo India' and equivalent make made up of thermosetting resign treated high pressure, self-supporting decorative compact laminates with permanently incorporate anti-bacterial agents during manufacturing .Compact board should be resistance to water immersion through permissible increase on thickness and mass <0.60% and board density >1.35kg/cm3 and fulfilled the criteria of FSC and green guard gold certification and manufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97 and EN438-6 with classification of BS1D0 standard. Pilaster to be supported with SS(grade316) adjustable foot and intermediate panels will attached to the wall with the help of approved SS(grade316) channels and all required hardware, made up of stainless steel as per manufacturer’s specification.. Door knob, gravity hinges, Thumb turn locksets with occupancy indicators, coat hooks with door stopper, U channel, top rail with corner connector, adjustable foot/pedestal, Rubber noise deafening tape, screw & wall plugs should be approved under the instruction of Engineer- in- charge. The top fitting should consist of SS. All screw will of 304 grade in SS with stain finish. All pilasters are supported by SS bottom cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150 mm. Finish and colour of Toilet cubical should be approved under guidance of engineer-incharge.

Providing and fixing undercounter wash basin of make JAQUAR, KOHLER, ROCA or equivalent oval in shape having Model No. CNS-WST-705, 2211IN-0, RS-322307460 respectively, including providing and fixing Undercounter basin with all fixing accesories, waste coupling of make JAQUAR, KOHLER, ROCA or equivalent having Model No. ALD-CHR-705L130, 45432IN-CP, RF5054018A1 and bottle trap of make JAQUAR, KOHLER, ROCA or equivalent having Model No. ALD-CHR-769L250190, 7314IN-CP, RF9066A1 including painting of fittings and brackets, filling the gaps with silicon and making good the walls wherever require with other necessary fittings completed as per site condition and as per the direction of EIC

Providing and fixing wall hung water closet of JAQUAR or equivalent having Model No. CNS-WHT-959SPP, with PP soft close seat cover, Hinges Fixing accesories & Concealed Flush pneumatic Tank with floor mounted frame, installation kit and P trap connection set & Dual Support bracket (Chair bracket) & pneumatic Faceplate of required matching shape and cistern fittings, nuts, bolts and gasket etc complete as per the direction of EIC.

Providing and fixing Pillar cock of JAQUAR, KOHLER, ROCA or equivalent having Model No. ORP-CHR-100001PM, 20747IN-8-CP, RT5A4225CA1 respectively as per the direction of Engineer in charge

Providing and fixing Bib Cock of 15 mm dia with wall flange of make JAQUAR, KOHLER, ROCA or equivalent having Model No. ORP-CHR-10037PM or equivalent as per the direction of Engineer in charge.

Providing and Fixing Health faucet with 1 m flexible pipe and hanging hook of make JAQUAR, KOHLER, ROCA or equivalent having Model No. ALD-CHR-565, 12927IN-CP, RF9061A1 respectively as per the direction of Engineer in Charge

Providing and fixing Stainless Steel Wall Mounted Sink Cock 15 mm dia of make Jaquar or equivalent as per the direction of Engineer in charge

Providing and fixing Two-in-one Bib Cock 15 mm dia of make Jaquar or equivalent as per the direction of Engineer in charge

Providing and fixing Two-in-one Angle Cock 15 mm dia of make Jaquar or equivalent as per the direction of Engineer in charge

providing and installation of Pinewood rafter ceiling as per design and specification finished with PU polish 50 X 50MM WOODEN RAFTERS CEILING PLACED @80MM C/C as per direction of Engineering-in-charge.

Design, Fabrication & fixing Metal Jaali with CNC cutting on Wall Panel of required Size and Shape of approved thickness two coat of PVD Brass Polish finished as per direction of Engineering-in-charge.

Providing and Fixing Photo Frame as per finalization of drawing/design as per direction and satisfaction of Engineer-in-Charge.

Providing and making wooden louvers with pine/beach wood finished with PU polish as per design and specification as per direction of Engineering-in-charge.

Storage : Providing & Fixing of storage of Make Geeken or equivalent, with back storage unit , MDF Top and PU finish as per direction of EIC. Min Size: L-2400mm, B-450mm, H-900mm

Service Counter : Providing & Fixing of service counter of Particle board top of Make Geeken or equivalent as per direction of EIC Min Size: L-2400mm, B-820mm, H-1000mm

Planter Box : Supply & Installation of Wooden Planter Box to be concrete finish as per direction of EIC. Size : L-950mm, B-400mm, H-600mm

Planter Box : Supply & Installation of Wooden Planter Box to be concrete finish Size as per direction of EIC. : L-2550mm, B-400mm, H-600mm

Planter Box : Supply & Installation of Wooden Planter Box to be concrete finish as per direction of EIC. Size : L-950mm, B-400mm, H-600mm

Planter Box : Supply & Installation of Wooden Planter Box to be concrete finish as per direction of EIC. Size : L-1700mm, B-400mm, H-600mm

Reception Table: Supplying reception table of Particle board top of Make Geeken or equivalent as per direction of EIC. Min. Size : L-1500mm, B-1000mm, Ht-600mm

Preparation and submission of lay out plan, customised Furniture arrangement plan, detailed design and execution drawings ( GFC ) based upon conceptual plan attached with tender document. The contractor shall get approved the Architectural consultant from AAI before proceeding with the consultancy. The consultant shall be fully responsible for adequacy, accuracy and quality of the architectural design. At least three conceptual drawings (3D) to be prepared as per Instruction and Satisfaction of EIC. Three Sets of Coloured (A0 Size) 'Good for construction' approved drawings or revisions thereof to be submitted before execution of work.

Sub Head B: Furniture Supply of following Furniture Make: Godrej /Geeken/Durian or equivalent as per satisfaction and direction of EIC. Five seater Curved Sofa, Material: Standard Fabric & Leatherite Min. Size: 3600 mm x 700 mm (For Tender Purpose Model Broadway V2 of Godrej & Model Regal L of Geeken considered)

Two seater sofa Material: 3D Woven Fabric Min. Size: 1515 mm x 830 mm (For Tender Purpose Model Edge of Godrej & Model Sirena 2 of Geeken considered)

Single seater sofa mid backwith seams with wooden angular armrests Material: Pinewood with termite resistant fabric frame Min. Size: 900 mm x 820 mm (For Tender Purpose Model Bobbin of Godrej & Model Questo 1 of Geeken considered)

Rectangular centre table Material: Wooden (Shessham frame) with soild wooden legs Min. Size: 1310 mm x 700 mm (For Tender Purpose Model Opulent Plus of Godrej & Model Alpha 2 of Geeken considered)

Circular/Oval centre table Material: Wooden (Shessham frame) with decorative legs Matt finish/SS 304 Gold Plated Frame and Leg, Virtified Tile Top with Gloss Finish Min. Size: 500 mm x 450 mm (For Tender Purpose Model Oval of Godrej & Model Lumis 1 of Geeken considered)

Arm Chair Material: Wooden Frame, Gase lift, wooden base Min. Size: (945-1055) mm x 700 mm (For Tender Purpose Model GP 102 of Geeken considered) (Note: Actual Size of Furniture from 58 to 63 will be decided after finalization of approved architectural drawing)

Sub Head C: Electrical Works SITC of Decorative light 01 as per attached design Concept drawings & as per approved by EIC.

SITC of Decorative light 02 as per attached design Concept drawings for closed lounges & as approved by EIC. .

SITC of 20 W Suspended Cylndrical Downlights as per attached design Concepts drawing & as approved by EIC. ( Make -Philips Cat No. SP320P LED20S-6500 PSU DIA80 WH / Equivalent Make of Bajaj / Crompton / Wipro/Havells)

SITC of 20 W Ceiling recessed Downlighters as per attached design Concepts drawing & as per approved by EIC. ( Make -Philips Cat No. DN590B M LED20S-6500 PSU WH MB/ Equivalent Make of Bajaj / Crompton / Wipro/Havells)

SITC of 140 Mtrs length 25 Watt Cove Light LED Strip , 3000 K with Aluminium Channel with long system life of 30,000 burning hours. Mounting accessories including Al channel,PC diffuser, leader cable & mounting clips With 28 Nos 25 Watt LED Drivers having IP65 Protection in VIP Room & Reserve Lounge completed as required. ( Make :- Philips /Bajaj/ Crompton / Wipro/Havells)

SITC of Grand Crystal Chandelier as per design Concept drawing for open lounges & as approved by EIC. .

SITC of 55' Display LED TV for closed lounges as approved by EIC. ( Make :- Sony/Samsung /LG)

SITC of dish HD connection with Set top Box having initial validity of 06 Months to above TVs complete as required. ( Make -Airtel/Tata Play /Videocon )

Supply of 190 Ltrs , 05 Star , Single door refrigerator for pantries complete as required. ( Make :- LG/ Haier/Samsung / Godrej)

SITC of office Dektop Computer having 21.5" screen , 8 GB RAM , 512 GB SSD , Window 11 with CPU , wired Key Board , Mouse with one year warranty for reception & Dining areas complete as required. ( Make :- Acer /Asus / HP or Equivalent Make )

SITC of 01 KVA UPS for above desktop Computers as required. Make :- ArrowPowetech/Micortek/Uniline)

SITC of laserjet computer Printer complete as required. Make :-HP/Brother/Canon)

Supply of Computer table as required.

Supply of High Back chair for computer operators as required.

Wiring for light Point /Fan Point/Exhaust Fan Point/Call bell point with 1.5 Sqmm FRLS PVC insulated copper conductor single core copper cable in surface /recessed steel conduit with modular switch modular plate suitable GI Box and earthing the the point with 1.5 Sqmm FRLS PVC insulated copper conductor single core cable etc as required. ( Group C )

Wiring for circuit /Sub main wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in surface /recessed steel conduit as required. (i) 2x2.5 Sqmm +1x2.5 Sqmm

RDO ENTERPRISES

nircon projects pvt ltd