Tender ID

Himachal

Cancelled

Works

Civil Works

HED/421/2025-26

Himachal Pradesh State Electricity Board Limited

ED Haroli | Una, Himachal Pradesh

Amount: ₹9.0 LCloses: 27 Mar 2026Closed

Timeline

Published19 Mar 2026
Closed27 Mar 2026
Cancelled1 Apr 2026

Corrigenda

Corrigendum

2 updatesLatest on 30 Mar 2026Submission Ends:27 Mar 20261 Apr 2026

Date changes

Download Ends27 Mar 20261 Apr 2026Submission Ends27 Mar 20261 Apr 2026Bid Opening27 Mar 20261 Apr 2026

Cancellation Details

Cancellation of Tender

CorrigendumcancelCorrigendumcancelReason: Due to admistrative reasons/issuesDocument: cancelled_1.pdf

Published 1 Apr 2026

Tender Value

₹9.0 L

EMD Value

₹9,042

Closing Date

27 Mar 2026, 1:20 pmClosed

Tender Inviting Organisation

Name

Sr.Xen

Address

(Er.Rahul Puri) Sr. Executive Engineer, Electrical Division, HPSEBL Haroli

Work Description

HED/421/2025-26

Tender Information

Tender ID

2026_HPSEB_131976_1

Reference Number

NO/HED-421/2025-26

Tender Type

Open Tender

Product Category

Civil Works

Form of Contract

Percentage

Period of Work

90 days

Location

ED Haroli

Source Website

Subscribe to view

Eligibility / Pre-Qualification

Please refer Tender documents.

Documents Required

2 documents required · 2 mandatory

Fee/PreQual/Technical

Requirednit (.pdf)

Finance

Requiredboq (.xls)

Fee & Financial Details

Tender Fee Amount

₹590

EMD Fee Amount

₹9,042

Important Dates

Last Activity

1 Apr 2026

Published

19 Mar 2026

Bid Opening

27 Mar 2026

Download Starts

19 Mar 2026

Download Ends

27 Mar 2026

Submission Starts

19 Mar 2026

Bill of Quantities

PercentageBoQ_Ver3.0INR

This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.

BoQ1 (0 items)

Sl No	Description	Qty	Unit	Est. Rate	Est. Amount
115 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)
212 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)
3Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer
4Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work
5Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete.
6Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
7Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)
8Providing and fixing wooden colour coated steel liner sheets (Tata/Jindal make) in eaves board / facia/soffits/ceiling including cutting, fixing & welding to steel roof members at all heights complete in all respect as per the satisfaction of Engineer-in-charge.
9Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately) :
10Powder coated aluminium (minimum thickness of powder coating 50 micron)

Stage Documents

Stage Summary Snapshot

stage.html

html • 0.02 MB

Cancellation Documents

cancelled_1.pdf

pdf • 0.42 MB

Documents

Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.

Tender Page Snapshot

details.html

html • 0.03 MB

NIT Documents

Tendernotice_1.pdf

PDF • 1.16 MB

Work Item Documents

termandcondition.pdf

Tender Documents • 0.82 MB

additionaltermandcondition.pdf

Additional Documents • 0.38 MB

BOQ_195151.xls

BOQ • 0.39 MB

Corrigendum Documents

extendd.pdf

PDF • 0.35 MB

corrgendum.pdf

PDF • 0.41 MB

Ready to Participate?

Download all tender documents and submit your bid

Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .

Loading…

Sl No	Description	Qty	Unit	Est. Rate	Est. Amount
115 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)
212 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)
3Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer
4Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work
5Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete.
6Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
7Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)
8Providing and fixing wooden colour coated steel liner sheets (Tata/Jindal make) in eaves board / facia/soffits/ceiling including cutting, fixing & welding to steel roof members at all heights complete in all respect as per the satisfaction of Engineer-in-charge.
9Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately) :
10Powder coated aluminium (minimum thickness of powder coating 50 micron)

Sl No

Description

Qty

Unit

Est. Rate

Est. Amount

115 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)

212 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

3Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

4Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work

5Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete.

6Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

7Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)

8Providing and fixing wooden colour coated steel liner sheets (Tata/Jindal make) in eaves board / facia/soffits/ceiling including cutting, fixing & welding to steel roof members at all heights complete in all respect as per the satisfaction of Engineer-in-charge.

9Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately) :

10Powder coated aluminium (minimum thickness of powder coating 50 micron)