Renovation of Various buildings at RHRTS Krishi Vigyan Kendra Tabo

Amount

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length etc. complete in all respect as per satisfaction of Engineer-in-Charge. ( hold fast lugs or dash fastener shall be paid for separately. a).Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge.a). 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing ISI marked oxidized/ Cromium plated M.S. sliding door bolts with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 250x16 mm( two hundred fifty into sixteen milimetre)

Providing and fixing ISI marked oxidized// Cromium plated M.S. tower bolt, (Barrel type) with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 200x10 mm ( two hundred into ten milimetre)

Providing and fixing ISI marked oxidized// Cromium plated M.S. Handles conforming to IS: 4992 with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 125mm (one hundred twenty five milimetre)

40 mm (forty milimetre) thick Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimetre)nominal size finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(TATA/ JINDAL MAKE)

6 mm (six milimetre) thick ceiling plaster with cement mortar 1:3 (one Cement: three sand) complete in all respect as per satisfaction of Engineer-in-Charge.

15 mm (fifteen milimetre thick) cement plaster on rough side of single or half brick wall of mix with cement mortar 1:4 (one cement: four sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Pointing on stone work with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Flush / Ruled pointing

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification etc. complete in all respect as per satisfaction of Engineer-in-Charge.. a). one or more coats on Old work.

Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge..a) One or more coats on old work

Finishing walls with water proofing cement paint of required shade in Old work (one or more coats @ 2.20 kg/10 sqm) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 Sqm and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge a).With cement mortar 1:4 (one cement : four sand)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty etc. in all respect as per satisfaction of Engineer-in-Charge a).Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Demolishing cement concrete manually/ by mechanical means including disposal of material within all leads etc. complete as per direction of Engineer - in – charge. a). Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all leads etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Area 3 sq. metres and below.

KESANG (BID ID -517813)

shashikant (BID ID -519905)